My 4 disk raid is far slower than I expected
measured using: # hdparm -tT /dev/sdb1
Timing cached reads: 32356 MB in 2.00 seconds = 16211.66 MB/sec
Timing buffered disk reads: 44 MB in 3.04 seconds = 14.46 MB/sec
[code]....
I have a 3ware controller that has a RAID 1 of two SATA disks.After an outage, the linux box (which is running ubuntu), restarted and the partition is now mounted read only. I only have the "/" mount point (this is a test server).Now, if I go to the 3ware controller by pressing ALT-3 while booting, I don't see any indication that there is something wrong with the disks.If I let the computer boot, I'm asked by fdisk if I want to fix/ignore/etc the inconsistencies found.
View 1 Replies View RelatedI am using Fedora 14 64 bit with two 1T drives. There is a Raid 1 for the important information and I use a Raid 0 for cached files that can be generated on the fly. Yesterday my Raid 0 went into read only mode.
Here are a couple of tests:
What caused the Raid 0 drive from /dev/md1 to get removed? Is there a way to get it back to active sync?
I have tried:
But it can not open /dev/sda2: Device or resource busy.
I set up software RAID 5 on three 7200rpm Seagate Barracudas (2x80GB, 1x40GB) with 40 GB partitions on the beginning of all three disks.Now, when I do benchmarks using the Disk Utility I get about 52 MB/s read speed on the array. This seems kinda slow considering the average read speed on each individual drive is about 48 MB/s. Also, boot up takes about 30 seconds, which is the same as when I had Ubuntu installed on just one of the 'cudas, without RAID. Now, I am I missing something? Shouldn't the read speed be more that twice as fast since it can read from all three disks?
View 1 Replies View RelatedI'm looking to set up a server with attached mass storage device and tape autoloader to run linux. It's set up under Windows at the moment. Goal is to have users, connecting from individual workstations and laptops, backup their data to the linux server. On their personal machine, some users run linux, some MacOS, some Windows. I plan to set up the 5 500 GB drives as RAID5. I understand that if setting up as software raid the format is "physical volume for RAID". Under this setup, will Windows users be able to read/write and function as expected? I can't assume only linux user access.
View 3 Replies View RelatedI am trying to install Ubuntu on a nvidia board which, based on the forums I have perused, is a FAKERaid chipset. Originally I tried to install according to https://help.ubuntu.com/community/FakeRaidHowto to no avail. I gave up and am resorting to breaking down my raid setup (thus losing my Windows XP installation) and using Linux's software raid (which seems to be the recommended method) with the Alternate CD install.
I went in to the bios and completely disabled my board's RAID function. I then followed the instructions here: https://help.ubuntu.com/community/In...n/SoftwareRAID , except it popped up with a window advising me "one or more serial ATA RAID configurations have been found. Do you wish to activate these RAID devices?" which that page didn't mention. I believe I selected "Yes". Setting up the partitions I made (from beginning of disk to end of disk) a RAID1 200MB /boot partition, a RAID0 / partition (90GB?), free space not set up in RAID (approx 20GB for each SATA drive to later install Windows on [if that's even possible]) & then the SWAP partition 2GB at the end of one of the disks (is it OK that this one wasn't in RAID?).
The installation completed, as far as I can tell, without a hitch. Except also of note: my network card doesn't work in the installer (gives an error message about unable to configure dhcp) so i'm not connected to the internet. Then I restart and the following appears: grub loading: error: biosdisk read error. Followed by what appears to be the Ubuntu loading splash (just a small white shape in the middle of the screen), and then:
[Code]....
migrate an installed Ubuntu system from a software raid to a hardware raid on the same machine? how would you go about doing so?
View 1 Replies View RelatedCould any RAID gurus kindly assist me on the following RAID-5 issue?I have an mdadm-created RAID5 array consisting of 4 discs. One of the discs was dropping out, so I decided to replace it. Somehow, this went terribly wrong and I succeeded in marking two of the drives as faulty, and the re-adding them as spare.
Now the array is (logically) no longer able to start:
mdadm: Not enough devices to start the array.Degraded and can't create RAID ,auto stop RAID [md1]
I was able to examine the disks though:
Code:
root@127.0.0.1:/etc# mdadm --examine /dev/sdb2
/dev/sdb2:
Magic : a92b4efc
Version : 00.90.00
code....
Code:
mdadm --create --assume-clean --level=5 --raid-devices=4 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2
As I don't want to ruin the maybe small chance I have left to rescue my data, I would like to hear the input of this wise community.
I want my samba to keep my windows attributes exactly what the user setted in windows I mean if it has read only file in win box and copy it to samba share ,samba keep it read only and same for other attributes but it does not do it now with my configuration:Quote:
[global]
workgroup = DOMAIN
server string = File Server
[code]...
What are the possible problem when Windows access the file from Ubuntu got Read Only even though have a full permission to read, write and execute the file? Ubuntu to Ubuntu accessing the file there is no problem only Windows got a problem.
View 1 Replies View RelatedI have a raid5 on 10 disk, 750gb and it have worked fine with grub for a long time with ubuntu 10.04 lts. A couple of days ago I added a disk to the raid, growd it and then resized it.. BUT, I started the resize-process on a terminal on another computer, and after some time my girlfriend powered down that computer!
So the resize process cancelled in the middle and i couldn't acess any of the HDDs so I rebooted the server.
Now the problem, the system is not booting up, simple black with a blinking line. Used a rescue CD to boot it up, finised the resize-process and the raid seems to be working fine so I tried to boot normal again. Same problem. Rescue cd, updated grub, got several errors: error: unsupported RAID version: 0.91. I have tried to purge grub, grub-pc, grub commmon, removed /boot/grub and installed grub again. Same problem.
I have tried to erased mbr (# dd if=/dev/null of=/dev/sdX bs=446 count=1) on sda (ide disk, system), sdb (sata, new raid disk). Same problem. Removed and reinstalled ubuntu 11.04 and is now getting error: no such device: (hdd id). Again tried to reinstall grub on both sda and sdb, no luck. update-grub is still generating error about raid id 0.91 and is back on a blinking line on normal boot. When you'r resizeing a raid MDADM changed the ID from 0.90 to 0.91 to prevent something that happend happened. But since I have completed the resize-process MDADM have indeed changed the ID back to 0.90 on all disks.
I have also tried to follow a howto on a similar problem with a patch on [URL] But I cant compile, various error about dpkg. So my problem is, I cant get grub to work. It just gives me a blinking line and unsupported RAID version: 0.91.
How long does hardware Raid card (raid 1, 2 drives)take to mirror a 1 TB drive (500gb used)?Is there a general rule of thumb for this?4 hours? 12 hours? 24 hours?
View 1 Replies View RelatedI am trying to connect a RAID Box to the server via LSI 8880EM2 RAID controller.The raid box is FUjitsu Externus DX60 with raid 1 configured.The server is Fujitsu Primergy SX300 S5 with LSI 8880EM2 RAID card.The external raid box is being recognised by the raid controllers bios.
The server runs CentOS 5.5 64bit. I have installed the megaraid_sas driver from LSI website and MegaCLI utility but CentOS still fails to see the box.MegaCLI utility, when launched from CentOS, recognises the raid box, CentOS does not(no mapping being created in /dev).
I have also tried to create a logical RAID0 HDD on one physical HDD(as seen by MegaCLI) with MegaCLI utility in CentOS.The result was success and the new logical drive could have been used, but when restarting the server, the controllers' bios fails with an error (not surprised(one logical RAID0 on one physical HDD)) and configuration is being erased.
Has anyone tried connecting 8880EM2 controller to a raid box with raid configured on the box, running it all under CentOS and what were the results.
I have installed Ubuntu on my m1530 since 8.04 and currently dual boot Win7 and 10.10. I would like to dual boot on my PC, but I have run into a problem. I am not a pro at Ubuntu, but this problem I can not solve by reading forums like I have in the past.
I realize this is a common problem, but I have noticed people having success.
I have a M4A87TD EVO MB with two Seagate drives in Raid 0. (The raid controller is a SB850 on that MB) I use the raid utility to create the raid drive that Windows7x64 uses. I have 2 partitions and 1 unused space. Partition 1 is Windows, partition 2 is for media, and the remaining unused space is for Ubuntu.
I am running ubuntu-10.10-desktop-amd64 off a Cruzer 16GB flash drive that was installed via Universal-USB-Installer-1.8.1.4.
My problem like so many others is that when I load into Ubuntu, gparted detects two separate hard drives instead of the raid. I read that this is because kpartx is not installed on 10.10. I then went in LiveCD mode and downloaded kpartx from Synaptic Manager. Gparted still reported two drives. I opened terminal and run a few commands with kpartx. I received an error. (Forgive me I didn't write it down, but I believe it said something about a communication error. I will try again later and see.)
Currently I am reflashing the Cruzer with a persistence of 4GB. I am not familiar with this process, but I understand that my LiveCD boot will save information I download to it. I decided to try this method because I was going to install kpartx and reboot to see if this made a difference.
I am looking for any suggestions on a different method or perhaps someone to tell me that the raid controller or some hardware isn't supported. I did install ubuntu-10.10-alternate-amd64 on my flash drive, but fail to get past detecting my CD-ROM drive since it's not plugged in. If this method is viable, I will plug it in. I also watched the ..... video were a guy creates Raid 0 with the alternated CD, but it wasn't a dual boot and didn't use a raid controller from a MB.
how can I create RAID 1+0 using two drives (one is with data and second one is new). Is it possible to synchronize data drive with empty drive and create RAID 1+0 ?
View 3 Replies View RelatedIf I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?
View 1 Replies View RelatedI have two 1TB hard drives in a RAID 1 (mirroring) array. I would like to add a third 1TB drive and create a RAID 5 with the 3 drives for a 2TB system. I have ubuntu installed on a separate drive. Is it possible to convert my RAID 1 system to a RAID 5 without losing the data? Is there a better solution?
View 1 Replies View RelatedI am going to be using CentOs 5.4 for a home storage server. It will be RAID6 on 6 x 1TB drives. I plan on using an external enclosure which is connected via two SFF-8088 cables (4 drives a piece). I am looking to try and find a non-RAID HBA which would support this external enclosure and allow to use standard linux software raid.
If this is not an option, I'd consider using a hardware based raid card, but they are very expensive. The Adaptec 5085 is one option but is almost $800. If that is what I need for this thing to be solid then that is fine, I will spend the money but I am thinking that software raid may be the way to go.
Ubuntu main O/S windows 7 running in Virtualbox how or can i read a usb flash drive in the windows O/S i want to read my mp3 player
View 4 Replies View RelatedIt's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
I am looking to convert a raid 1 server I have to raid 10. It is using software raid, currently I have 3 drives in raid 1. Is it possible to boot into centos rescue, stop the raid 1 array. Then create the raid 10 with 4 drives, 3 of which still has the raid 1 metadata, will mdadm be able to figure it out and resync properly keeping my data? or is there a better way to do it?
View 2 Replies View RelatedI have a box that doesn't have a Raid controller or a software raid running currently. I would like to make it a RAID 1. Since it seems there isn't any IDE RAID controllers hardly around, I have another HD that is the exact model as the drive currently in the box running CentOS. Can I some how add the second drive and get the box to mirror from here own out? The box gets really hot and I want to be ready for a HD failure.
View 3 Replies View RelatedThe titles says about everything. CD's are perfectly automounted.WhenI insert a DVD however (I tried various DVDs), absolutely nothing happens, as if I would have inserted nothing or a blank DVD.I already read lots of threads and nothing o help... Here are the outputs of a few commands that might or might not be useful.A line I added myself in fstab which appears completely useless:
Code:
/dev/sr0 /media/dvd auto utf8,user,noauto,exec 0 0
Code:
[code]...
I've tried to install Fedora 11, both 32 and 64 on my main machine.It could not install as it stops on the first install window. I've already filed a bug but really haven't seen any feed back yet.The bug has something to do with Anaconda and the Raid array but I really can't tell.
I have an Intel Board (see signature). I am running intel raid software under W7 currently.It works fine. But, I'm wondering, when I attempt to install F!!, is my current raid set-up causing problems? Do I need to get rid of the intel raid software and use a Fedor/Linux raid program to manage the raid array??
I'm thinking of adding a 40GB H/D to a 80GB H/D using RAID.I don't know if the size difference will affect performance.Is it worth the time? Would it run like a 120GB H/D?(or close to it).
View 3 Replies View RelatedI have been having problem with my failed disk RAID server.
The regular mdadm --assemble cmd does not work.
After trial&error, I am able to add all disks to the RAID using mdadm.
However, it is still inactive. How do I activate this RAID md0?
The result from cat /proc/mdstat
Code:
I have 2 drives and wish to use the following partition setup.
sda1 /boot 1GB ext4
sda2 / 50GB ext4 raid 0
sdb1 / 50GB ext4 raid 0
Unfortunately only Ubuntu server has the option to make a raid in the install. Can somebody point me to a howto on something like this up. I'm thinking I will want to install onto a sdb2 set up the raid and copy the file system to the raid.
Using: Linux server 2.6.32-25-generic #45-Ubuntu SMP Sat Oct 16 19:52:42 UTC 2010 x86_64 GNU/Linux
I have two identical 2 TB eSata external harddisks. Until recently I had them configured as a RAID-1 array. I find that resyncing takes a lot of time, reducing availability too much. Is it good idea to split the disks into 4 partitions of 500GB and use LVM to make them appear as 1 again? The idea is to reduce syncing time to 1/4-th but I might be over-designing here. How likely is it that only 1 partition would need resyncing? Is there a significant performance-penalty when combining RAID and LVM? Is there a simpler solution? How about using notify to automatically back-up essential changes?
What is use of lvm and raid in industries? I want to know this.
View 11 Replies View RelatedI am trying to partition my server before installing CentOS and cPanel.I have hardware RAID 1/10 On RAID 1 I would have
/
/boot
On RAID 10 I would have
/tmp
/usr
/var
/var/log
2 GB swap
/home
Is it correct partionining setup?What should I have on RAID 10 ?