Fedora Networking :: Connect To A WIFI Require WEP Key?
Jun 21, 2009
I tried to connect to a WIFI require WEP key. I make the WEP key myself. I wrote it down on a piece of paper myself. My PSP can connect to the network, my XP can connect to the network. But same machine, my Fedora 11 can not connect to the network. As long as I tried to connect to the network, network manager just keep asking me for the WEP key. I put in the WEP key and tired out every option the network manage offer(WEP40/128bit, share key, etc),
View 3 Replies
ADVERTISEMENT
Jan 21, 2010
I have just installed the last FC distro, and everything works good, except the wireless network.I have a Linksys N-Ultra WirelessN USB wifi card, model WUSB600N.It uses the rt2x00 driver, concretely the rt2870 driver (at least, thats the driver included in the original device drivers CD).Right now, the problem is that i don't know how to make my Fedora 12 to enable and/or connect to internet.
dmesg | tail
usb 1-3: Manufacturer: Cisco-Linksys LLC
usb 1-3: configuration #1 chosen from 1 choice
[code]...
View 4 Replies
View Related
Aug 10, 2010
My laptop has an internal wifi adapter, but I recently purchased another one because of its extended range.susb, shows that the new adapter is:
Code:
Bus 002 Device 027: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
After disconnecting my internal adapter from the wireless network, I can scan for networks
[code]...
View 13 Replies
View Related
Sep 25, 2010
I just installed Fedora 13 64bit Gnome, but I can't connect to the internet for some odd reason.
If you look at the image below:
I have marked the network icon, but on my desktop I don't have that icon for some reason...
Since I'm new @ Linux(Picking it up again) I went to the services and checked 2 services:
The network manager service was running but the status said: This service is dead.
And the network service was also running but status was: The status of this service is unknown.
I also went to the Administration menu and checked Network, the first tab showed no devices, but when I went to the hardware tab it did show my card.
I also don't believe that this is hardware problem since the card worked just fine under Fedora 9 or 10(Don't remember).
So if anyone got some solutions for me it would be great...
Some related hardware info:
lsusb
Code:
Code:
View 2 Replies
View Related
Aug 29, 2009
I have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
View 3 Replies
View Related
Aug 9, 2011
My wireless card is:
Code:
03:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0083]
On Fedora 15, when I boot kernel 2.6.40, my laptop is unable to connect to my wireless-G AP. dmesg shows the following:
Code:
[ 43.866090] wlan0: direct probe to 00:27:19:14:c2:ca (try 1/3)
[Code].....
It works fine, however, when I boot using kernel 2.6.38 (from which I am posting) and in Windows. Also, I found some emails from the linux-wireless mailing list which appear to be talking about the same problem.
The system is fully updated. I've tried the 11n_disable=1 hint I came across on the ThinkPad wiki, but it didn't help. (I'm on an Asus K42Ja, in case it's relevant)
Although I'm fine with staying at 2.6.38 for now, are there workarounds/fixes for this?
View 7 Replies
View Related
Mar 3, 2010
The auto connect feature of NetworkManager Applet (version 0.7.997) isn't working on my system. If the WiFi connection dies, Network Manager doesn't detect that the connection has been lost and try to reestablish the connection. I have to manually click on the WiFi hotspot to reestablish the connection. This appears to be the case both while the computer is running and when I first boot it up (i.e. when booting, if the first attempt at establishing a WiFi connection doesn't succeed, Network Manager doesn't retry or try another hotspot).Is this "normal" behavior for Network Manager? If not, does anyone know a fix? Here's some more info about my system:
Computer: Dell Inspiron 1318 laptop
WiFi Chip: Broadcomm BCM4238
Kernel Version: 2.6.31.12-174.2.22.fc12.x86_64
[code]....
View 3 Replies
View Related
Aug 6, 2010
I know Windows forward and backward but I am so new to linux it's just wrong. I just installed fedora (like 1hr ago) on and old toshiba laptop with a WiFi PC card. Everything seems to work fine except. My Networks connects to my home Wifi network but it will not connect to internet. When it connects the IP address isn't even close to being in the same range as my other laptops and PCs. Like I said I'm new to linux but I'm wanting to learn. Any fixes for this issue? Which linus book is the best one to read for a beginner? Other then not connecting to internet I have no complaints.
View 14 Replies
View Related
Aug 8, 2011
I can connect to the internet through wifi, but I cannot connect to anything on my network. I have a printer and a NAS, so I would really like for this to work again. I have a dell laptop with a Broadcom card.
View 9 Replies
View Related
May 3, 2011
I can not connect to wifi networks, i can see them but not connect.
My wifi device is:
View 9 Replies
View Related
Dec 2, 2010
Having played around with ubuntu a fair bit I decided to breathe life into an old thinkpad with a pcmcia wireless card, by following the minimal install instructions and using lxde window manager etc.. Everything works fine apart from the fact that I cannot connect wirelessly. The card picks up and lists connections but whenever I have clicked on a connection the dail spins and then it gives up.I installed network-manager and managed to get nm-applet appearing in the sysTray otherwise I would not even have known there was wireless connections there.
I was thinking there maybe some conflict with another network manager, does this sound likely?
View 3 Replies
View Related
Jan 14, 2011
I'm having an issue recently with Ubuntu 10.04 x64. Connecting to my wifi is not working. I believe it is some kind of issue with the router. On Windows 7 the only way that I could connect to the net was by copying the network profile to a usb flashdrive from another computer and loading it mine. The wireless signal just keeps attempting to connect.
View 1 Replies
View Related
May 28, 2011
I have Ubuntu 10.04 on my EeePC 1000H. I don't use this computer often but it has always worked before... I suspect an update did this to me. I've recently swapped wireless routers but all my other machines have been able to connect to the new router. I can see the SSID and the signal strength is high but when I try to connect to it, it just attempts for a long time then asks me for my password again. I am currently connected to wired network.
Code:
michael@michaelsEeeUbuntu:~$ nm-tool
NetworkManager Tool
State: connected .....
pan0 Interface doesn't support scanning.
View 8 Replies
View Related
Jun 17, 2011
I installed Ubuntu 11.04 yesterday and my wireless didn't work so I searched a little and found a way to make it work; Uninstalled bcmwl-kernel-source and installed firmware-b43-lpphy-installer and b43-fwcutter. And it worked. But today I accidentally pressed the "turn off wireless" button on my laptop. I obviously pressed it again and thought it would work but it doesn't. Now I find networks and stuff but I can't connect to them. It tries for awhile and then asks me to enter the password which I do (it is correct) and then it tries to connect for a few minutes again and then it asks me for the password again.
Some info:
Code:
lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset
[Code].....
View 9 Replies
View Related
Aug 25, 2011
I'm having a problem to connect to the network at home via wifi, open or protected. Using ubuntu 11.04, attached are more details. I've managed to get a successful connection on an open network at work.
View 7 Replies
View Related
May 20, 2011
Im using Fedora 14, and I use mifi2372 for wireless wifi. The device is new and it will not connect to my laptop. Im sure the device is okay however I dont know about my laptop. The switch that turns on wifi does not turn blue.
View 9 Replies
View Related
Jan 7, 2010
is it possible to connect to my internet router from the console? for some reasone my gnome envirment removed and i want to install it again.
View 5 Replies
View Related
May 21, 2010
I can connect to my home WiFi connection with no trouble at all.
I can't connect to a free public WiFi (like at a library).
View 2 Replies
View Related
Jul 27, 2010
i am tryin to connect to internet through wifi. for this i have to connect to router first and then open the web browser to put UN and PW. I am using ubuntu. i know UN and PW. I can connect to router but my(any) web browser cannot open the authentication page.
View 3 Replies
View Related
Aug 12, 2010
I have a 2wire card and gateway how do I install it and connect to the internet?
View 2 Replies
View Related
Sep 10, 2010
I have a good connection with 9.04 but when I upgrade it to 10.4 the network keeps looking for wiFI. I have a Linksys USB adapter 2.4HZ.
View 8 Replies
View Related
Nov 30, 2010
I just installed the XBMC from the XBMC live CD. I want to configure it in a way to auto-connect to internet. (my router is wpa-password protected.)
i know how to save the password and auto connect to internet from gnome GUI but not how to do it from command line. what should i install, change or configure in order to auto connect to internet? (using command line)
View 1 Replies
View Related
Jan 4, 2011
I am running 10.10 on a Toshiba NB255 netbook. Wireless works find for me at home and worked last week at a hotel. At home I just use WEP, and my office network uses WPA. I can connect just fine from my work laptop but not from this netbook. The network shows up fine in the network manager and it asks for the WPA password, but doesn't establish a connection. Every once in a while it will say it is connected and has full strength but I can't ping anything, and within a minute or so it drops again. IIRC yesterday it connected via wireless and actually worked for maybe a minute before dropping at it hasn't worked since. Like I said, this has worked on other wireless networks.
Here is some output from dmesg:
Code:
[55086.034476] wlan0: authenticate with 00:15:62:ff:6e:89 (try 1)
[55086.037598] wlan0: authenticated
[55086.037658] wlan0: associate with 00:15:62:ff:6e:89 (try 1)
[55086.041880] wlan0: RX AssocResp from 00:15:62:ff:6e:89 (capab=0x431 status=0 aid=4)
[55086.041891] wlan0: associated
[55089.045810] wlan0: deauthenticated from 00:15:62:ff:6e:89 (Reason: 2)
[55089.079974] cfg80211: All devices are disconnected, going to restore regulatory settings .....
View 9 Replies
View Related
Feb 18, 2011
So recently we switched Internet Providers. While we had Bellsouth, my laptop would connect to our wireless internet flawlessly everytime. However, we just switched to Charter because it was both cheaper and faster. But now, my laptop will not connect to our wireless. If I hook it up to an Ethernet cord, it connects just fine. I believe they gave us a new modem/router or whatever it is that sends out the wifi signal.
I have tried to connect with this laptop on Ubuntu, Linux Mint, and Backtrack 4. On Ubuntu and Linux Mint, after I enter the correct WEP key, it sits there and tried to connect for a minute or two, but then the window pops up asking for the WEP key again, even though it's still filled out.
When I tried connecting on Backtrack, it told me that it could not obtain an IP address.
View 9 Replies
View Related
Mar 15, 2011
I think I have unique problem. I have a d-link DWL G510 rev c.(Austrailian) WiFi card in my pc which is detected as
Quote:
Network controller [0280]: RaLink RT2561/RT61 rev B 802.11g [1814:0302] in lspci -nn.
iwconfig shows:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=6 dBm
Retry long limit:7 RTS thrff Fragment thrff
Power Managementff
ppp0 no wireless extensions.
Now sometimes it detects my wifi router and shows its ssid in nm-applet. but when I try to connect, it tries for 3 or 4 minutes and then fails. for most of time it even does not finds my router.
View 1 Replies
View Related
Apr 7, 2011
about 90 percent of the time, i cannot connect to the internet. i click on the icon and select the network, but for some reason, instead of saying, "connection established", it says, "you are now disconnected."
View 2 Replies
View Related
Apr 24, 2011
Wireless adapter is working OK because I can connect when network is unsecured, but when I try to connect to the secured wifi it just won't accept the password.
I can see available networks in Network Manager but can not connect. No error messages, just no connection.
Is there anything I can try to enable connection to the WEP secured router?
View 3 Replies
View Related
Apr 26, 2011
Just reinstalled ubuntu 10.10 x86 on an old laptop.
The wireless doesn't seem to work and I have no idea how to solve this.
In gnome I can see NetworkManager display the network ESSID.
I have entered the key but no success, it tries to connect and then times out after about 1-2 mins.
I have tried to change the encryption from WPA2, to WPA to WEP to nothing but the same issue.
In a terminal/shell running ifconfig/iwconfig I can see eth1 as the networkinterface.
How can I investigate this further. If there was an IRQ collission or something it would not be showing the ESSID right?
View 3 Replies
View Related
Apr 30, 2011
I have installed both win7 and ubuntu, and with win7 i can easily connect to wifi in my arrea. Why i cannot i connect with this? I've installed the system with wired internet, and i'm trying to connect to a unsecured wifi.
View 9 Replies
View Related
Jun 5, 2011
My wifi was working find on 10.10 but since 11.04 it doesn't work. code...
View 5 Replies
View Related
