I created a F14 x86_64 guest OS in VirtualBox4 (hosted by F14 x86_64) and configured it to get its IP from my router but it won't do so on boot. The other guest OS's (Fedora 14 i386, 2x Oracle EL5) are able to get their IPs on boot.
I checked the setting in the network manager and they show that the interface is to be activated on boot but it doesn't. When I log in and run ifup eth0 as root it works.
I cannot get static addresses to work on eth0 and eth1. eth0 seems to use DHCP while eth1 uses the static information. Sometimes the static info is used but the interfaces get the addresses reversed.
From /etc/sysconfig/network
NETWORKING=yes
HOSTNAME=mosaic
[code]....
I generally check what updates are being installed. This time sadly I didn't and again this kernel had one missing module. VirtualBox-OSE stopped working. It had been working fine with other upgrades. No it's not a problem with dkms or other stuff. This kernel doesn't have vboxdrv module like other kernels...i verified it...
[Code]...
The 2.6.38.8 version doesn't have vboxdrv module!....hence again I have to roll back to older kernel. So before blindly upgrading....read this message!
I'm trying to set up Virtualbox to run as a service so that it auto starts the VM when the PC boots and shuts down the VM when the PC is shut down.
I've found a set of scripts that do this but set up of the scripts was written for Ubuntu so I'm stuck at one of the steps.
The set of scripts can be found HERE
The part of the install that I'm not sure about is the part in bold. I know what it's trying to do (basically start the script last during the boot process and stop the script first during shutdown) but don't know how to do it in oS.
VBoxTool currently consist only of a set of scripts. With this scripts, virtual machines of VirtualBox in a Linux headless server can be controlled. Start, stop, save, backup and show status of sessions in batch mode from the command line.
Usage and installation is tested only on Ubuntu. Please report if a specific function is not working in another environment, say OpenSUSE, Fedora, etc.
INSTALLATION:
My network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
Fedora (2.6.34.6-47.fc13.x86_64) I installed that update, during the installation process it said that it had to remove three packages, one of them was kmod nvidia for the old kernel (Fedora (2.6.33.8-149.fc13.x86_64))After the update finished installing the new kernel, I restarted the system and Nvidia did not load. (I assume because Update manager removed the old nvidia? But I also assumed that a new version would be installed automatically?)I received the following Boot messages:
Code:
Entering non-interactive startup
Starting monitoring for VG vg_user1: 3 logical volume(s) in volume group "vg_user1" monitored
[code]....
I'm confused, if Update Manager removed kmod nvidia, then why does yum say it is installed? And why doesn't the new kernel update work with that version? Or should I install a driver version for that particular kernel? I've read while searching that I need to install a kmod-nvidia for that particual kernel version and that I should login to my previous kernel until that happens, is that the problem I'm having?
Why don't rpmfusion and fedoraproject release the kmod-nvidia and kernel updates at the same time to avoid problems such as this? Does anyone know how long does it usually take for rpmfusion to release the new kmod-nvidia driver for the latest kernel?
my internet was fine.. until.. i had to work in the school so.. a teacher configured the internet settings.. for something .. ( i don't remember) and everything was fine. but when i returned to my house and conected my lap to internet (cable) the internet didn't work.
ubuntu@VR:/etc/network$ ifconfig
eth0 Link encap:Ethernet direcci�nHW 00:1d:72:46:38:3c
Direc. inet:192.168.1.65 Difus.:192.168.1.255 M�sc:255.255.255.0
Direcci�n inet6: fe80::21d:72ff:fe46:383c/64 Alcance:Enlace
[Code].....
I'm trying to get skype to work on my new system. It seems to install, but trying to run it I get an error message naming a missing dependency. Searching for this with yum whatprovides and installing the result worked in one case, but for the next one, yum install <package containing missing item> returns a few errors of the form:
package <name-version>.fc12.x86_64 (which is newer than <package-version>.fc12.i686) is already installed Is there any way around this? I'd like to get skype working, but am having no luck at the moment. I'd prefer not to remove the .x86_64 packages if I can avoid it in case that breaks something else.
I have installed the Squeeze testing version. i have setup networking for static in the /etc/network/interfaces file. tried to find resolv.conf in the /etc/ since could not find i created this file post trying to start the eth1 i am able to ping my ip, but if try to ping the gateway i get an error saying the ping is not sucessfull. I have 2 network cards, eth0 and eth1. as eth0 does not work i have configured eth1. The dump of the interfaces file is below
[code]...
The same setup works fine in Ubuntu 10.10 setup that i have.
I am running the latest ubuntu and I am having trouble getting networking sorted. I have 2 networks, one wired (eth0) and one wireless (wlan0). I connect to the internet using wireless. The problem is that I can only successfully connect to the internet if I disconnect from eth0. I have hit this problem with Windows machines and the solution was to adjust the "interface metric" in "Advanced TCP/IP Settings" so that the wireless was the preferred connection. How can I achieve something similar in Ubuntu?
View 1 Replies View RelatedProblem: Can't get bridging to work properly.
I'll start by saying that most of this is built inside of a 64bit ESXi 4.1.0 server. Should be obvious by the picture below.
Trying to set up a bridged CentOS box. Ultimate goal is to set up a Transparent Firewall. The machine labeled 'Desktop' is a Windows XP running DHCP. It gets assigned an Internet routeble IP address. At this point, nothing is running a firewall.
Symptoms:
Gateway can ping CentOS bridge
CentOS bridge can ping gateway
CentOS bridge can resolve DNS names and ping FQDNs on the Internet.
CentOS bridge CAN NOT ping Desktop
[Code]....
On my HP TX2500 laptop, dual-booting Vista and 9.04, Ubuntu installation found the WLAN and it works fine.I installed VirtualBox with Vista as the host and 9.04 as the guest. Wired Ethernet works fine but it didn't seem to find my WLAN. What more do I need to do?
View 1 Replies View RelatedI use ubuntu 10.10 x64. Bluetooth dosn't autostart. I can start it pressing Fn + F3.
View 9 Replies View RelatedI just installed Fedora 11 (excellent work by the Fedora team!) and got my Verizon mobile USB CDMA device working after some file modifications (easily found via searching).
I have to click the network icon in the task bar, and select "Auto Mobile Broadband (CDMA) Connection" to get it to connect though. It then shows up via "ifconfig" as ppp0 and all is good.
But how do I get this to auto-start when the system reboots? It doesn't show up in the network manager, and I'm not even sure how to use command-line to start up the CDMA connection! I only can do it via clicking that icon.
I upgraded from 10.10, and there were no apparent problems during install. However, Unity doesn't start when I use the Ubuntu session from GDM. I have guake terminal installed, which starts correctly, so if I open that and run unity as a background process, everything works perfectly. I would like a solution other than adding it to my startup apps, because I still use GNOME every now and then.
View 4 Replies View Related5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.
ifconfig eth0:
Code:
eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
I have a couple VPNs I use for work, and after installing F14 x86_64 it is failing:
Code:
Nov 5 12:40:57 raykj NetworkManager[4106]: <info> VPN service 'vpnc' started (org.freedesktop.NetworkManager.vpnc), PID 4203
Nov 5 12:40:57 raykj NetworkManager[4106]: <info> VPN service 'vpnc' appeared; activating connections
[Code]....
Since 2.6.27.19-170.2.35.fc10.x86_64, dhclient wlan0 doesn't seem to work any more.
However, bizarrely, dhclient eth0 does (to the same D-link wireless router).
The AP shows connected - tail /var/log/messages
No working leases in persistent database - sleeping.
WINXP connects just fine. This (B43) has worked nicely ever since FC10 came out, and I was able to use the WiFi at all kinds of places on a recent trip. Other than a couple of yum updates, I don't think anything else has changed since. Other devices on the wlan are getting their DHCP requests satisfied correctly.
Is anyone else having this problem since about a week ago? Perhaps there's something really obvious I'm missing. I can manually assign an IP address to wlan0, manually edit the routing tables and edit /etc/resolv.conf, and then Wifi seems to work OK, so it doesn't seem to be b43 itself unless it is dropping DHCPOFFERS. If this isn't a regression, does anyone have any tips about how to debug this?
The sc spreadsheet app doesn't really work in 64bits. It launches but you're unable to do anything with it, it's not possible to enter any values in the cells or do anything else. It works fine in 32bit though.
To make it work properly in 64bits, you can use this patch, borrowed from debian: http://salix.enialis.net/x86_64/13.1...changes-7.16-3
And there is also this patch to make DESTDIR work properly with the Makefile: http://salix.enialis.net/x86_64/13.1...-destdir.patch
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
I downloaded Fedora 10 32bit and put it on a Dell Dimension 8200 to save it from the recycle bin. Everything seems to work except I cannot get an IP addr. Roadrunner is my ISP using a cable modem and a Linksys Instant Broadband Series Etherfast Cable/DSL router model BEFSR41. In system-config-network, the nic shows inactive. If I activate it a window opens saying "determining IP information for eth0". After a short time the message adds the word "failed". Using a Windows PC on the same network, I can look at the DHCP connections on the Linksys and I see the MAC addr for the PC running Fedora.
From the OS installation, /etc/sysconfig/networking/devices/ifcfg-eth0 has following:
DEVICE=eth0
HWADDR=00:80:ad:d1:88:c9
ONBOOT=yes
[Code]....
I'm guessing this is a r8169 problem. This worked for a while after upgrading to fc13 (from fc12)
I'm not able to get off the local network with eth0. I can though with eth1. Both interfaces are connected to the same switch and have the same network, gateway, and dns server addresses.
The odd part is I am able to ping eth0 from off the LAN and get a reply.
Wireshark capture is attached.
I can't start eth0 and have read thru many of the threads on this and can't figure it out. What does this message mean?
Code:
[jeff@chladni ~]$ ifup eth0
Active connection state: activating
Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/13
[Code]....
I have a Broadcom Corporation BCM4312 802.11b/g (rev 01) wireless card. I installed these packages:
broadcom-wl-5.10.91.9.3-1.fc12.noarch
akmod-wl-5.10.91.9.3-3.fc12.6.x86_64
kmod-wl-2.6.31.6-145.fc12.x86_64-5.10.91.9.3-3.fc12.8.x86_64
[code]....
uname -a says:
Linux boz.alafkhar 2.6.31.6-145.fc12.x86_64 #1 SMP Sat Nov 21 15:57:45 EST 2009 x86_64 x86_64 x86_64 GNU/Linux
and:
# lsmod | grep wl
wl 1278432 0
lib80211 6436 2 lib80211_crypt_tkip,wl
[code]....
My networkmanager understands that the card is installed. But it can not find any network. Also iwlist scan gives me no result. I did not have this problem on earlier fedora releases. Recently I upgraded to F12 from F11. I should mention that I have another USB DLink wireless card and when I plug it, everything works fine with that card. I also tested wl_apsta driver using fw-cutter. I did not work neither.
I just built some machines with the Intel 82574L gigabit ethernet chip, loaded Fedora 14, and discovered a problem with the e1000e driver dying after a few minutes. A little time spent perusing the web told me that the same driver had problems in Fedora 12 and Fedora 13 as well. Congrats to Fedora for the hat trick.As of kernel 2.6.35.10-74.fc14.x86_64, e1000e driver 1.0.2-k4 still had bugs.[URL]
View 6 Replies View RelatedIt looks like the ocfs2console is broken on openSuse 11.4 64bit. I tested on several servers and my laptop. It works under 11.3 x86_64 but that uses Python 2.6. OpenSuse 11.4 uses Python 2.7.
I tried to submit a bug but I can't seem to get my email address verified so I can use the bug tracker.
Server1:~/python-gtk/pygtk-2.12.1 # ocfs2console
ERROR: Unable to initialize the windowing
system: The CObject type is marked Pending Deprecation in Python 2.7. Please use capsule objects instead.
Server1:~/python-gtk/pygtk-2.12.1 # uname -a
Linux Server1 2.6.37.1-1.2-xen #1 SMP 2011-02-21 10:34:10 +0100 x86_64 x86_64 x86_64 GNU/Linux
Server1:~/python-gtk/pygtk-2.12.1 # python
Python 2.7 (r27:82500, Aug 07 2010, 16:54:59) [GCC] on linux2
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedI just installed Fedora 10. I entered my static network info in Network Configuration. When rebooting, the eth0 says Inactive. I've read many articles about this problem on earlier versions and tried many of the suggestion, but have not found a definite way of solving this. Is there a better way or a workaround to get this machine on the network?
View 6 Replies View Related