Fedora :: Loading Modules To Work With Card Reader Using F13?
Aug 7, 2010
I found a solution to my card reader problem in a another fedora post but when I type the code in terminal I get:
all config files need.conf /etc/modprobe.d/blacklist
How to write this code so I wont get this error and I can load these modules and also how to edit the modprobe.conf.
The code is below, using fedora 13.
You must load these two modules to work with card reader.
First : Remove the card from the Reader!
AS superuser type in console :
1. /sbin/modprobe tifm_core <enter>
2. /sbin/modprobe tifm_sd <enter>
If you want to automate these modules loading do the following :
edit the /etc/modprobe.conf file
add these :
alias mmc_core tifm_core
alias mmc_card tifm_sd
View 2 Replies
ADVERTISEMENT
Mar 29, 2011
I have problem with my Genesys Logic memory card reader. I'm trying to read SD-memory card. When I put the memory card in to the card reader, nothing happens. Also ls /dev/sd* don't show any new drives/partitions.Here is my dmesg when I put the card in:
Code:
[ 2808.136056] usb 1-5: new high speed USB device using ehci_hcd and address 82
[ 2808.264921] usb 1-5: New USB device found, idVendor=05e3, idProduct=0710
[code]....
View 4 Replies
View Related
Jul 13, 2015
I have a Thinkpad X220 (stretch/sid) with a built-in SD card reader.But when I plug in an SD card it won't show up in the file manager (thunar), nor as a /dev/sd* or /dev/mm*.. URL...
Code: Select all$ udisksctl status
Just my internal SSD shows up.How do I get my SD card reader to work?
View 5 Replies
View Related
Dec 9, 2009
I could use some instructions on how to get firefox to read and use my cac card. Under Yast the card reader shows up in hardware. I have install pcsc ccid and coolkey through Yast but not sure if I need to do anything else. I have followed instructions for loading the device in firefox but it does not load my certs off of the card.
View 8 Replies
View Related
Feb 25, 2010
My multimedia card reader does not work with new ubuntu version fresh install:
lsusb says:
Code:
Bus 001 Device 002: alcor micro corp. multimedia card reader
dmesg:
Code:
[6.544269] usb-storage: device scan complete
[6.544848] scsi 2:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[6.545482] scsi 2:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[6.546102] scsi 2:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[6.546728] scsi 2:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[6.547227] sd 2:0:0:0: Attached scsi generic sg2 type 0
[6.547338] sd 2:0:0:1: Attached scsi generic sg3 type 0
[6.547439] sd 2:0:0:2: Attached scsi generic sg4 type 0
[6.547550] sd 2:0:0:3: Attached scsi generic sg5 type 0 .....
View 2 Replies
View Related
Jun 28, 2011
I can't seem to get my card reader to work. The USB port on the reader works and sometimes I can read my SD card. Usually, nothing shows up in the media/ folder. I looked at this write-up [URL]... but I'm not sure if this is what I should do. Here are some info I was able to pull up:
sg_scan -i Code:
/dev/sg0: scsi0 channel=0 id=0 lun=0 [em]
HL-DT-ST DVD-RAM GH22NP20 2.00 [rmb=1 cmdq=0 pqual=0 pdev=0x5]
/dev/sg1: scsi0 channel=0 id=1 lun=0 [em]
[Code]...
View 7 Replies
View Related
Sep 1, 2010
I have installed Ubuntu 10.04 32 bits version on a desktop PC. Every thing works OK, exept for a USB hub and card-reader combination from IN-WIN Inc. I could not find a clue on the Internet.
The manufacturer and apparatus code is: ID 10df:0500 (as from "lsusb").
Below I have listed all the hardwire of the PC, as obtained from "lshw". The italic part at the bottom deals with the IN-WIN module. I suspect that it may have to do something with the "emulated scsi-host" thing, of which I just know nothing about.
JGMS:
View 2 Replies
View Related
May 10, 2010
I just installed opensuse 11.2 on my laptop in a dualboot configuration with windows 7.I prefer using suse, but also recognize, that once in a while, windows is useful.One of the things i like to do in linux is handle my photos with f-spot/gimp, but for some reason my laptops built in card reader is not recognized by the system. If a card is inserted, it doesn't even show up in the partition manager..?I'm not completely new to linux, but i'm not an advanced user either, so i can't figure out what to do here
View 5 Replies
View Related
Feb 13, 2010
When I insert the xD card into the built-in 5 in 1 card reader of my laptop it doesn't work. An SD card for example does work with this reader, so it is not a "faulty hardware" problem we are talking about right now, and neither is a "HW is not recognized" kind of a problem. My card reader is seen as a
Code:0f:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)in the lspci output.I use debian testing with a 2.6.32-trunk kernel (what is this "trunk" here anyway?)I know this isn't a unique problem and with a cheap external USB powered card reader (I have one) this whole thing can be worked around, but still.
View 2 Replies
View Related
May 11, 2010
I've been trying to load my pcmcia network card driver "xirc2ps_cs" at startup with no success. I have added "modprobe xirc2ps_cs" to the rc.modules file but it doesn't load at startup. Curiously, though, if I execute rc.modules AFTER the machine has booted it will load the modules just fine. Just not during the boot up process. Thinking that hotstart might have been causing problems I've disabled hotstart (chmod -x) temporarilly to remove it from the picture, but there was no change.
View 5 Replies
View Related
Nov 24, 2010
Everything worked fine in Kubuntu 10.04 (64-bit). On the upgrade to 10.10 (64-bit) it takes about a minute until I can move the mouse after startup and the integrated memory card reader doesn't work (but the green LED which used to only come on when there was a card in there is now always on). This has been discussed twice before: here (closed and solved by unplugging cardreader which I do not want to do) and here (unsolved but closed as maverick no longer in beta) dmesg (note the errer -110) follows. Let me know if I can/should include any other logs/info!
Code:
[ 13.575002] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 13.790470] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 13.903728] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 16.280020] usb 1-5: device descriptor read/64, error -110
[ 17.375755] sky2 0000:02:00.0: eth0: enabling interface
[ 17.376174] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.377028] type=1400 audit(1290608578.996:5): apparmor="STATUS" operation="profile_load"
[Code]......
View 2 Replies
View Related
Jan 1, 2009
I have an Acer Aspire One running Fedora 10.The Aspire One has a built in multi-format memory card reader compatible with SDHC, XD, Memory Stick Pro and MMC cards, however the card reader is only detected during bootup if a card is inserted otherwise the device isn't detected, the relevant drivers aren't loaded and the card reader doesn't work.
In other words if Fedora is booted without a card in the reader and I then want to use the card reader I have to insert a card and reboot in order to use it, after which cards can be inserted & removed and are detected and automounted with no problems.When the card reader is working lsmod shows the following modules are loaded.
[Code]...
If the laptop is booted without a card in the reader none this shows up. I've also tried manually loading the mmc_core, mmc_block, sdhci, memstick & jmb38x_ms modules to see if this kicks the reader into life but it doesn't. Is there a way of forcing the detection of this device during bootup?
View 14 Replies
View Related
Jan 20, 2010
Looking for a card reader/writter that will support most current card types. I am running Fedora 12 x86_64. Are there any gotchas, that I need to watch for? Also, Internal vs. external, any benifits of one over the other, or is it just personal preference?
View 2 Replies
View Related
Jun 10, 2009
Anyone running fedora 11 have any luck getting a smart card reader added as a security device under firefox?
Specifically from firefox: Edit-Preferences-Advanced-Encryption tab-Security_Devices-Load;
Enter arbitrary name and "/usr/lib64/libcoolkeypk11.so" as the module.
This worked fine in fedora10 and was the necessary step to getting a card reader to work with firefox. In fedora11 (with firefox beta) the browser just comes back with nothing, it doesn't even respond. Note I am familiar with the concept of pki and certificates as well as certutil, pkcs11_inspect, pklogin_finder, etc. Also note utlities like pkcs11_inspect and pklogin_finder and esc all work and communicate with the reader and read the contents of the card but smart card login configured via the authentication applet (as working in fedora 10) is not working either.
View 3 Replies
View Related
Jun 10, 2010
I have fedora 13 (64 bit) in my laptop with athlon amd processor (64 bit). I installed adobe pdf reader. but does not work. any solution?
View 3 Replies
View Related
Jun 10, 2010
I installed adobe pdf reader in my lap top with amd 64 bit processor and fedora 13 (64 bit). But it does not work
View 2 Replies
View Related
Feb 1, 2010
I've got a wireless card and would like to make a driver module for it from the ralink tarball. Here's the details:
1. The Asus PCI-G31 uses the RaLink RT2561/RT61 802.11g chipset.
Code:
lspci
<some output omitted>
04:03.0 Network controller: RaLink RT2561/RT61 802.11g PCI
2. I am using the latest driver download from www.ralinktech.com which is
2009_0123_RT61_Linux_STA_v1.1.2.3.tar.bz2
3. I followed the documentation and I think it makes a script. Here's part of the README from the tarball.
Code:
Build Instructions:
1> $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
2> $cp Makefile.4 ./Makefile # [kernel 2.4]
[code]....
View 3 Replies
View Related
Jan 20, 2010
Looking for a card reader/writer that will support most current card types. I am running Fedora 12 x86_64 on a home-grown desktop. Are there any gotchas, that I need to watch for?Also, Internal vs. external, any benefits of one over the other, or is it just personal preference?
View 5 Replies
View Related
Nov 8, 2010
im currently using fedora 14 kde and i cant find a working comic book reader, i currently have the comic "the last man" and all the files are in .cbr, if someone could help me with this it would be greatly appreicated, i have tried installing mulitple comic book readers, so mabye a lil step by stepalso while i am posting, i currently use yumex to download all of my apps and stuff but some are out of date is there any way to update all the databases to recieve the most up to date apps?
View 6 Replies
View Related
May 21, 2011
I am running 11.04 and would like to stop the loading of the parport and lp modules. I put entries in the /etc/modprobe.d/blacklist.conf file and ran update-initramfs -u. After a reboot lsmod shows both modules as being loaded.
View 1 Replies
View Related
Aug 29, 2010
I have to load the ip_conntrack modules every time I reboot. How do I get the iptables modules to load automatically at boot. It seems they are supposed to auto load when they are needed but they are not doing that. I have to do modprobe on them. also does anyone know where I can download all the modules available for iptables? I looked on the netfiler site and did not learn much.
View 1 Replies
View Related
May 21, 2011
I am running 11.04 and would like to stop the loading of the parport and lp modules. I put entries in the /etc/modprobe.d/blacklist.conf file and ran update-initramfs -u. After a reboot lsmod shows both modules as being loaded.
View 4 Replies
View Related
Jun 10, 2011
For some reason, it seems that 13.37 isn't loading the modules I need for cpu frequency scaling. I've edited /etc/rc.d/rc.modules so that CPUFREQ is set to on. On 13.1, this would mean the powernow-k8 module would be loaded for my AMD cpu, and the subsequent "ondemand" governor would be loaded. However, for some reason this isn't being done during the boot process. I've tried it using both the generic kernel and the huge kernel (I'd been using huge for a long time before without realizing it.) Has anything changed in 13.37 with regards to CPU frequency scaling?
View 5 Replies
View Related
Jan 23, 2010
The problem I am having is that iptables won't load the required modules for my firewall rules.
iptables -F
iptables -P INPUT DROP
iptables -P FORWARD DROP
[code]....
View 1 Replies
View Related
Sep 1, 2011
I've recently been having a lot of trouble trying to install a ralink 3062 driver on my ubuntu 11.04 desktop. There are quite a few excellent tutorials on this website. [URL]... In my case, however, adding the conflicting drivers to /etc/modprobe.d/blacklist.conf didn't prevent them being loaded at boot-time, so I could not make the change permanent. I eventually found a workaround online which I thought I'd share here. Once you have updated your blacklist and module list, use Quote:
sudo update-initramfs -u
I'm a beginner so I'm not sure, but I think the problem is that initramfs loads the conflicting modules into memory before the system comes to reading the blacklist and module files. Once you've done this, restart your system and you shouldn't have any further problems. P.s. As far as I know this only works (but should only be a problem for kernel 2.6 and later)
View 2 Replies
View Related
Apr 8, 2011
i don't see my sd card reader ?(under xp this card reader "works" but don't read datas ?)
hwinfo give
57: SCSI 00.0: 10600 Disk
[Created at block.254]
[code]...
View 14 Replies
View Related
Dec 6, 2010
I have all of my music on an SD card so it doesn't take up space on my hard drive. I put it into my SD card reader and ubuntu is all like, "gtfo doesn't exist."
View 2 Replies
View Related
Mar 30, 2011
I have installed Ubuntu 10.10 in my system. I have plug in th USB card reader but it is not detected. Eventhough the same card is detected when I'd pluged in at last night and I have just browse the folders in the memory card.Then I just right click on the icon in media folder and click eject the texts in file /var/ log/messages for above operation.
View 2 Replies
View Related
Apr 9, 2010
I am very new to Linux. I installed ubuntu 9.10 on my Acer 3050 aspire. It works very well except for a few issues. I can not use my 5 in 1 card reader, nothing shows up in "computer" except "cd/dvd" and "file system". My lg phone does not show up when using my data cable as mass storage, and the touch pad is too sensitive, (i have adjusted the settings listed under mouse/touchpad but to no avail. The biggest problems is the card reader and phone. Can this be fixed?
View 14 Replies
View Related
Jul 18, 2011
Stuck an SD card into my laptop (acer timelinex 5830tg) for the first time today, and to no avail. I've done an lspci, but don't seem to see my card reader there. here's the output
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family HECI Controller #1 (rev 04)
00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4)
00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4)
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b4)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4)
00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04)
01:00.0 VGA compatible controller: nVidia Corporation Device 1050 (rev a1)
02:00.0 Ethernet controller: Atheros Communications AR8151 v2.0 Gigabit Ethernet (rev c0)
03:00.0 Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PCI-Express) (rev 01)
04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01)
05:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
I'm running kernel 3.0-rc6. Issue still remains when booting into 2.6.39 also.
View 14 Replies
View Related
