I'm facing some problems with FC11 in my PPC G4. I tried installing and everything went well until it reaches a stage where I'm being prompted to select my network interface.
The options are: wlan and eth0
But no matter which one I choose I still get this error "An error occurred trying to bring up the wlan0 (or eth0) network interface". And if I click cancel, the installation aborts. how can I can FC installed??
when I tried to configure network I came across a problem that the enable button on top of network manager GUI is disabled. So alternatively I enabled it with ifconfig command. I also configured DNS servers. But the problem is whenever I reboot my machine. I have to reactivate the network from terminal and give the DNS servers again, because DNS settings are not saved.
In short, attached a terminal screenshot of me trying to install hplip. Why hplip-3.9.10.run doesn't recognize the fact that gcc has already been installed? In detail: I have HP PSC 1210 connected to a Windoze XP machine. I want to enable network printing, but the only printer showing up standard in the F12 drivers is the HP PSC 1200. When I use that one, I reach the printer, and the Windoze printer queue, but no matter how long I wait, nothing ever comes out of the printer. It'll start moving like "I'm about to print!" but then does nothing. So through the hp-opensource website I determined which driver I want, and get a long way into installing the file. It hangs up on the attached screenshot.
Config: Squeeze, 2.6.32-5-amd64I just installed squeeze and the network is up and nm-manager deamon if working but the Gnome applet doesn't seem to work as usual. It indicates no network although the network is available as indicated by ifconfig and route below. When I switch WiFi on, the nm works flawlessly. When I click on the applet icon it says "Wired Network: device not supported" (or similar, msg in french is
I have a laptop connected to the the net thru an adsl modem, when I switch off the laptop network interface,(thru system-config-network) the light of the laptop network card plugged in the router stays on ( green) where as in my pc, when i do the same thing , the light of my pc network card goes off in the modem
After an online upgrade from f11 to f13, on rebooting the setup attempts to configure the wireless connection and fails with a not very illuminating "error configuring your network interface" notice, offering no option but to go back and try again, which of course fails again with the same error.
Wireless card is a D-link that works fine with the ath5k driver in f11.
how I can get out of this vicious cycle and proceed with booting the upgrade?
I was told to simply go into the fstab folder to allow myself permissions to execute files without becoming root, but instead of following it blindly I need a 2nd opinion. I cannot install a specific program because of configuration problems even though I downloaded all the gcc, g++ etc packages.
I found multiple sites explaining how to add IPs to a network interface as virtual interface like eth0:0. However I can add IPs to an interface as well using the ip command: ip a a 192.168.2.2/24 dev eth0 What I want to know is how I can make this persistent on rhel/centos.
tell me how to activate my wired NIC permanently?Also, how do I disable the 'work offline' check box in Firefox.At present I am required to action both before accessing internet.
I simply cannot get this to work, has anybody managed it?
My problem is related to tuncfg I believe. I make the modification to the source of tuncfg to change ifconfig to /sbin/ifconfig. If I run hamachi start debug I get the following output:
It appears it cannot create the hamachi network interface because it doesn't appear under ifconfig.
My setup is as follows, Machine-1 - Two network interface cards on same network with different MAC say MAC-1 and MAC-2 - IP 10.209.193.130 and 10.209.193.131 - Firewall IP tables empty iptables -F Machine-2 - One NIC with IP 10.209.193.135 switch - both machines are connected to common switch and can ping happily.
Problem: when I send ping request from Machine-2 to Machine-1 arp tables are initialized for IP MAC pair. Surprisingly both IP are get resolved to one MAC i.e MAC-1. general observation is, MAC of first interface which has route in kernel route table. I cross checked this on Suse11 and RHEL5 same result. but In suse10 I am getting expected behavior [i.e IP1-MAC1 and IP2-MAC2 pair in arp cache]. Do any one know why kernel is using same NIC for two different interfaces?
Output for Suse11 and RHEL 5 Code: ? (10.209.193.131) at 00:0c:29:34:e7:6f [ether] on eth3 ? (10.209.193.130) at 00:0c:29:34:e7:6f [ether] on eth3 Output for Suse10 Code: ? (10.209.193.128) at 00:0c:29:02:9a:7c [ether] on eth3 <-------- Suse 10 machine-1 ? (10.209.193.131) at 00:0c:29:34:e7:6f [ether] on eth3 ? (10.209.193.127) at 00:0c:29:02:9a:72 [ether] on eth3 <-------- Suse 10 machine-2 ? (10.209.192.1) at 00:00:0c:07:ac:07 [ether] on eth3
I have just installed debian-live-8.3.0-i386-lxde on my old hp530 32-bit laptop
Everything went well but every time I start my laptop I get following message which lasts for approx 1m 20s ...
Code: Select allLoading, please wait... fsck from util-linux 2.25.2 fsck error 2 (No such file or directory) while executing fsck.ext4 for /dev/sda1 fsck exited with status code 8 [Â 13.941532] systemd-fsck[145]: DEBIAN8: clean,140919/640848 files, 978992/2560942 blocks [ ***]A start job is running for LSB: Raise network interfaces. (1min 20s / no limit) with the 3 asterisks above moving back and forth.
... then it boots OK into operating system. so apart from the delay everything is working ok.
I'm a newbie on Linux and trying to find my feet so please be kind.I have installed vmware on my XP laptop and have installed fedora core 9. Network setting on the VMware is set to bridged. My interface eth0 which is using the wireless does not start on boot. I have to run ifup ifcfg-eth0.The file ifcfg-eth0 had onboot=yes and NM=no, so i changed it so that the NM=yes.However this does not resolve the problem at all. I have put the file back to its original configuration and I have disabled network manager and have had no luck
I'm writing to you because I encountered the following problem. My program displayes all network interfaces that are available in the system, but I would like to adda functionality in which a user can enter a destination address IP (ex. the IP address of the Google search engine) and will get information which network interface will be used to send it. As I know it is associated with reading information from routing table in the system. Maybe you know the API (functions/methods) which I could use to do it in RedHat ? I program in C/C++, but if you know how to do it in other programming languages (Java, Perl, Python) I will be grateful for any information.
Someone just erased my HWADDR line from /etc/sysconfig/network-scripts/ifcfg-eth0. How can I obtain my original MAC address?
Code:
ifconfig eth0 does not work (it shows the wrong MAC address) since the HWADDR line from the file I mentioned above was erased. Also there is no ifcfg-eth0.bak backup configuration file.
I use chrony on my laptop thinking it would be better for it than ntp because I'm frequently connecting and disconnecting from wireless cafe access points and going in and out of suspend mode. But I've also noticed that if chrony is started before the access point is connected it never syncs to the time servers. I have to manually restart it via the service command after I connect. This doesn't seem right to me, if chrony fails to find a network at start time, doesn't it periodically try again ?
I have b43 wireless. In network Configuration on system->administration the interface it appears as inactive it appers in hardware also as b43 associated to wlan0 but i cannot have access to any wireless network. What i have to do to put this b43 to work.
I have a dell optiplex configured with an extra PCI network card, because I plan to set it up as a gateway / LTSP server, but I have troubles getting the second network card to work. It is recognized during installation (where I can choose the primary network interface) and doing a
Code: lshw -class network
After installation shows both network cards, with network 0 being labeled Disabled. I have tried configuring the other network interface in the /etc/network/interfaces file, but it has failed to work. I have also briefly looked at udev rules, but it seems that it renames the interfaces fine during bootup, as
Code: dmesg | grep "udev" Shows the following Code: [1.138307] udev: starting version 160 [6.003002] udev: starting version 160 [7.237092] udev: renamed network interface eth1 to ethlokal [7.253775] udev: renamed network interface eth0 to eth1
I also noticed a briefly shown "address collision" error of some sort during boot, but it never shown for long enough for me to read it through. The network card that is enabled is an Intel 825662EZ 10/100 ethernet controller, and the one that is disabled is a Realtek RTL-8139/8139C+.
I don't want my wireless network card to be automatically enabled in Network Manager when I start my computer. I keep setting it to disabled in Network Manager but when I reboot Network Manager has re-enabled it again.
Is there some way of starting with wireless disabled until I tell Network Manager to enable it?
I am totally new to Linux and have just installed ubuntu 10.10. After configuring the network interface via dhcp I started getting these messages that come in so frequently I can't configure anything else.
[87.186415] Stack:
Why I am getting this messages and more importantly how do I get rid of them.
today I tried to configure a network route to a host for testing my network interface. Code: route add 192.168.1.15 eth0 As I have to eth interfaces and both interface got their IP from DHCP (192.168.1.11 and 192.168.1.12) and are in the same subnet, I shut the other interface down:
Code: ifconfig eth1 down Then I tried to test the interface by doing a ping to 192.168.1.15. Problem: When I unplug the cable from eth0 (and eth1 is still plugged) the ping still works. Somehow my linux (it's debian) powers up again eth0 and pings over this port.
How can I stop my linux doing this. I just want to have the route added only on the one interface - not the other. Is it maybe some case of a default-gateway?
Last night while setting up wired & wireless connection in openSuse 11.2 Gnome version via YAST's ifup, I got wireless but lost wired connection (interface eth0). Dmesg shows that eth0 became eth1. I cannot get eth0 back. Is there any way to remedy this situation, eg. get info from the Ubuntu partition in my triple-boot laptop, without having to re-install openSUSE?
This may be more suited for the networking forums, but I figured Community Cafe would be well rounded enough for someone to tell me if this is even possible (with minimal configuration that is).There are a few places I travel where I only have a wired connection to the Internet (no wifi), but when this happens is there a simple way to create an adhoc network so wireless devices can route through my computer and to the network? Reason I'm asking is I'm thinking of getting an iPad or iPod Touch which have wireless connections, but in the cases where my laptop is using a wired ethernet connection and the wireless card isn't used, I'd like to create an adhoc wireless network that'll let such wireless devices work.
I tried to install VPN server/client on my Linux machines. But the instruction document mentioned: "The following should work (assuming your outside interface is eth1 and your inside interface is eth0):". What is " outside interface" and what is " inside interface"
My machine showed this: ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7392 (7.2 KiB) TX bytes:7392 (7.2 KiB)
p2p1 Link encap:Ethernet HWaddr 00:21C:42:A4:19 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:43
Ubuntu rocks but I am having trouble enabling PAE.
I want to do it to have my full 4Gb RAM recognized by my 32bit OS. At the moment System Monitor only recognizes 3.2Gb and the command "free -m" shows the same value.
I followed these instructions but they don't seem to work: [URL]
PS: The point is to really understand how to achieve this and not to start a debate "32bit vs 64bit OS choice"
Is there an easy way to enable libfaac in ffmpeg? I'm hoping to not have to compile it myself, but it appears that it was compiled without libfaac support. Not sure if what I'm using is from rpmfusion, but it's enabled.