I installed debian jessie on my asus T200TA but wifi isn't recongnized
I nevertheless followed the same steps as for installation on asus T100TA on debian wiki.
[URL] ....
I've tried everything I was able to do alone but I can't figure why my laptop won't suspend. It just goes dark and wakes up again.
Here my /var/log/syslog from my last suspend attempt : [URL] ....
Code: Select all$ uname -a
Linux N550JV 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt9-3~deb8u1 (2015-04-24) x86_64 GNU/Linux
(my PC runs on dual-boot with Windows )....
I recently bought a used Asus eee 1001PX. It came installed with some spyware called windows which I replaced with jessie. Everything works great but one thing. When I plug in headphones I get no sound in the headphones. If I have some audio running and plug them in while it's playing it doesn't cut the audio from the built in speakers off like it should do. If I start and look at Output Devices in pauvcontrol it seems like it at least recognizes that I have headphones inserted.
I didn't have a chance to test if the physical audio jack was broken while it had Windows running on it but assuming that it's not physically broken, what might be wrong? I know very little about audio, alsa, pulse and that kind of stuff so I hardly know even where to start.
Some info:
Code: Select alllspci -v
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Device 8437
Flags: bus master, fast devsel, latency 0, IRQ 44
Memory at f7cf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
[Code] ....
so I had to reinstall Ubuntu.But now my Wireless card won't work. It used to work before (plug and play), and I have no problem with it when I boot from the CD.I cannot use my cable connection because as soon as I plug my computer in, the network crashes, the router doesn't respond, gets hot and refuses to work until I unplug it and let it cool off for 2 minutes.I'm using Ubuntu 10.10, Desktop PC.
Code:
:~$ lsusb
Bus 001 Device 002: ID 0846:4260 Netgear, Inc. WG111v3 54 Mbps Wireless [realtek TRL818B]
[code]....
I use jessie-32bit of kernel 4.1.3 on ASUS EeeBook X205TA. But it doesn't recognize buttery status.Result of my investigation, the incomprehensible ponts is below.
・"acpi -b" outputs no information.
・There is not "battery" directory in /proc/acpi/. (button only exists.)
The following is my system informations.
Code: Select allacpi -V
Adapter 0: on-line
Cooling 0: intel_powerclamp no state information available
Cooling 1: Processor 0 of 10
[code]...
I want to check battery in console and fluxbox Desktop.
I use jessie-32bit of kernel 4.1.3 on ASUS EeeBook X205TA.
And I use Japanese Model. There are key 【,|】and【,_】in this model keyboard. [URL] .... But my system does not recognize the two keys.
In /etc/default/keyboard, edit below
XKBMODEL="jp105"
XKBLAYOUT="jp"
I can japanese layout, but the two keys is nonreactive.
And i can not dpkg-reconfiguration keyboard-configuration. It's no response. No appear.
Code: Select all#dpkg-reconfiguration keyboard-configuration
update-rc.d: warning: start and stop actions are no longer supported; falling back to defaults
update-rc.d: warning: start and stop actions are no longer supported; falling back to defaults
Running Jessie, x64 Intel iCore 7 16 RAM with a properly partitioned drive to the specifications I prefer. Running the KDE Shell. For some reason my third monitor is not detected by Debian Jessie at all. When I run the command to list the monitors lspci | grep VGA I think. Only two monitors are listed, I know the other monitor works. During Grub bootup it even has some startup text running in it.
View 9 Replies View RelatedI have a very weird issue with a Acer chromebook laptop (CB5-571) After fresh install of Jessie I just can't seem to have any trace of the touchpad and by that I mean nothing in dmesg or /proc/bus/input/devices or even /var/log/Xorg.0.log is mentioning anything about any sort of touchpad device.
So being desperate I loaded live Xubuntu 14 and the touchpad worked just fine so after some checks it turned out that Xubuntu is using elan_i2c driver which I can't find anywhere.
Also I've tried loading the psmose module but that made no difference as I guess the HW is just not recognized by the system.
dmesg |grep PS
Code: Select all[ 1.069210] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.069211] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.070064] mousedev: PS/2 mouse device common for all mice
uname -a
Code: Select allLinux localhost 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1+deb8u6 (2015-11-09) x86_64 GNU/Linux
I upgraded my laptop from Debian Wheezy to Jessie the other day, and just as before my wifi auto-connects to my router, and I can "ping http://www.google.com" just fine, but only for like a minute. Then the Internet access dies, but I'm still connected fine to my router, and I can ping its IP address. If I connect to the router through cable / eth0 everything works just fine, and I have full Internet access.
I assume there is something wonky with how ip address is assigned after the upgrade, how can I fix this, or trouble shoot further?
(I run Gnome desktop, with network manager).
A couple of days ago I followed a guide online in order to install Adobe Reader and this guide recommended a specific package that needed the jessie repository, I added it (unaware the jessie was the name of the new distribution on testing) and so I found myself upgrading to Jessie, which is fine since is working quite alright, but since then I can't sent any document to my wi-fi printer.
I had no problem with Wheezy, I installed two printers: one connected to the usb interface and the other one to the wifi (but is actually the same). With Jessie when I try to print something and select the wi-fi one nothing happens. If i try to add a new one I can't since debian doesn't find it and I can't even delete the old "malfunctioning" one.
On install my wifi was working, but when I rebooted it stopped working.Since then I've tried numerous things to attempt recovery of wifi. No luck so far.
View 14 Replies View RelatedMy wifi does not work in the actual debian testing jessie lxde amd64 with wicd version (fresh install). What I've done:
0. Fresh testing jessie install (offline and ignored the question for adding iwlwifi)
1. Adding following sources:
deb http://ftp.de.debian.org/debian/ jessie main contrib non-free
deb-src http://ftp.de.debian.org/debian/ jessie main contrib non-free
deb http://security.debian.org/ jessie/updates main contrib non-free
deb-src http://security.debian.org/ jessie/updates main contrib non-free
2. apt-get update
3. apt-get install firmware-iwlwifi
4. modprobe -r iwlwifi ; modprobe iwlwifi
So searching the web just brings up the wheezy way solution (backport new kernel and iwlwifi).
But in this case, actual jessie testing kernel is already installed by default and so the actual 43 firmware-iwlwifi
Some information:
Code: Select all# dpkg -l |grep -i iwlwifi
ii firmware-iwlwifi 0.43 all Binary firmware for Intel Wireless cards
Code: Select all# dmesg | grep wifi
[ 7.890216] iwlwifi 0000:02:00.0: irq 107 for MSI/MSI-X
[ 8.478878] iwlwifi 0000:02:00.0: firmware: direct-loading firmware iwlwifi-7260-9.ucode
[ 8.479867] iwlwifi 0000:02:00.0: loaded firmware version 23.214.9.0 op_mode iwlmvm
[ 8.553105] iwlwifi 0000:02:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
[ 8.553193] iwlwifi 0000:02:00.0: L1 Enabled - LTR Enabled
[Code] ....
I must add: lxde Debian uses Wicd, so network-manager is not installed !
Wicd seems to be the problem. After changing to network-manager, everthing is ok.
Next install with the official Jessie release, i will look, why wicd not work out of the box.
I'm a brand new user of Debian, and I just bought a (too much?) new laptop, the HP 430 G2. It seems to work great for almost everything, except that I don't have any wifi available.
I tried so many different things (without any success) that it would be hard to resume. But for now, all I have is a new installation (to avoid parasite installations of weird things), and a kernel updated to 3.16. I don't know if it's useful though...
Some information from my system :
Code: Select allbonyhoax@bonybook:~$ sudo ifconfig
[sudo] password for bonyhoax:
eth0 Link encap:Ethernet HWaddr 14:58:d0:09:72:bd
inet adr:130.125.57.144 Bcast:130.125.57.255 Masque:255.255.255.0
adr inet6: fe80::1658:d0ff:fe09:72bd/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:27329 errors:0 dropped:0 overruns:0 frame:0
TX packets:3491 errors:0 dropped:0 overruns:0 carrier:0
[Code] ....
The first element I notice is that I don't have the line with "Kernel driver in use...". Which seems to indicate that there's a problem with the kernel module (is that right?). But I don't know how to fix it...
The other thing that puzzles me with these last two commands is that according to this page, my wifi card is a Broadcom BCM43142. But it's not the result I get with the lspci command.
Anyway, I'm really lost, I don't know what to do, what to check, what to install. I don't want to go by random, testing all the different solutions I see on the web blindely. This is the reason why I ask it here.
I recently finished a mini-itx machine and everything was working great with a fresh Jessie install. I put in a PCIe wifi card and now the computer won't boot. The power LED is on, the PSU fan is spinning, but I get no display output at all and I don't know how far into the boot process the thing even got. I removed the card and the machine boots fine again.
I only have one PCIe slot so it is my only option, I don't have another PCIe card to try, nor do I have another machine to test the wifi card in. The card is brand new, for what it's worth.
WiFi card: [URL] ....
motherboard: [URL] .....
I have did a clean installation of Debian Jessie today on my laptop and my computer.I use the Gnome 3.14.1 Desktop environment.
I installed Spotify-Client via PPA, and i installed the gconf-editor, gufw and Google Earth. Those 3 applications are not visable in the Gnome applications menu.
If i run then via the terminal, e.g. spotify-client, gconf-editor, gufw and google-earth, the applications are started. They seem to be installed correctly. I tried either running apt-get purge spotify-client gconf-editor google-earth-stable gufw, and reinstalled those applications, to no avail.
I even tried installing another desktop environment, mate-desktop. The shortcuts to the applications do exist in /usr/share/applications. Only not in the Gnome 3 menu. It's strange, because this problem happens both on my desktop and my laptop computer.
I run:
Debian Jessie 8.2.0 with Gnome 3.14.1.
Kernel 3.16.0-4
amd64 architecture
I also tried reinstalling Gnome-Shell and GDM. But it doesn't work.
Before, Debian Wheezy 7.9 was installed, and there was no problem. My Debian installation is fully up-to-date.
I have Lenny running on my old Toshiba Qosmio E10 via wired ethernet. what I need to do to get the intergrated wireless adapter recognised, configured etc.
View 4 Replies View RelatedAs the subject states i have a desktop with a radeon 9200 card, when i install the firmware-linux-nonfree the system hangs when x starts(sometimes you can see the login manager, sometimes not, but you cant login at all) and i cant access any of the terminals ctrl+alt+f(1-6), after removing the firmware-linux-nonfree package the system boots, but the graphics are under software render...
View 3 Replies View RelatedI have a desktop PC which initially had the Intel D946gzis mobo, its chipset as video controller, some RAM and so. There I installed Debian without a problem alongside WindowsXP.
I've bought an ASUS HD 4670 video card, installed it on the PC and now the installed Debian does not work, while the Ubuntu live CD refuses to run no matter if I set acpi, apic on or off... it throws me some low memory corruption at position just like shown here. With normal configuration, Debian throws kernel panic (keyboard lights blinking). Anyone have faced this before? Ideas? Thanks!! (meanwhile, debian hides in a virtualbox :'( )
Edited: Tried Ubuntu 9.10 x64 (due to the fact i've a core2duo at 2GHz) and it throws a kernel-panic to me (flashing caps and num LEDs). On screen, can be read different lines with things like:
[ 1.957161] [] rb_erase+0xd6/0x160
[ 1.957266] [] page_fault+0x25/0x30
Could it be something about this new video card having ddr3?
My Asus k52 BBR9 was working great with Meerkat until I put in all the updates.Now it won't recognize my wireless: it says were connected and the icon is clear or it is dark or has the icon look pulsing where there is my connection. But I can't get online.
View 2 Replies View RelatedOS Version: CentOS 5.3
Motherboard: ASUS M3A78-CM (BIOS v.2003)
I have a single disk running the base OS and just installed 2 x Seagate 500GB SATA 3.0 drives in a RAID1 set that I would like to use for data storage. The OS sees the drives individually but not the RAID. Has anyone worked with a similar board and has any ideas what I need to do to get the OS to recognize the RAID1 array?
just installed opensuse 11.3 on my asus eee pc 1018p and have severe problems to make the wireless network card work. tried to install the driver with ndiswrapper and b43-cutter, but without any success. ifconfig does not show any wlan0 device. below find output of
lspci -v
dmesg
ifconfig
installed opensuse on several notebooks/netbooks before but never ran into serious trouble.
[code]...
My office has a box which is, by necessity, dual-boot WinXP/Slack. The Slackware I'm running there is -current, all great and fine. Until now... It turned out that my mobo, an ASUS P5KPL-CM, died after a power surge. Since the XP needs software activation, we replaced it for an exact copy of the mobo. After the change the box worked fine in XP, and I was able to connect to the network via the Ethernet interface. BTW, the Slackware version is Slackware-current, updated as of the Jan 9 update (after that I was no longer able to connect to the Net with Slack). However, in Slackware there was a problem: eth0 was no longer recognized. Using /sbin/ifconfig only listed the lo (loopback) interface. The lspci output is:
Code:
01:00.0 Ethernet controller: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0)
Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
[code]....
Hi,I'm using a Dell Lattitude D620 laptop. I just installed the latest kernel 2.6.38 in my Squeeze amd64 :
Output of uname -r
2.6.38-bpo.2-amd64
Now I'm running on new kernel,everything seems fine except my wifi ( now I'm connected through ethernet ). Before I do the process with the guide in http://wiki.debian.org/wl to activate my wifi,I'd like to ask for some advice here,is this latest kernel support my wifi card? If yes,how to activate it?
Output of lspci :
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
[code]....
i cant get this right for some reason. i switched from ubuntu to fedora. in ubuntu i had the same issue with the touchpad, but there i found a fix which worked with ubuntu, but not with fedora.[URL]... the problem in fedora is that i dont have any psmouse.ko module in /lib/modules/2.6.39.4/kernel/drivers/input/mouse so the patch cant really be applied so i get an error, saying there is no psmouse
i found a fix, but since my knowledge with linux is limited i didnt get it right. "I spent some time trying to get this working (and one will find other threads here, on the Fedora list, etc, where I was trying to get help), but the problem, in the end, is that Fedora doesn't install the PS/2 mouse driver as a module, but builds it into the kernel. So the solution was to recompile the kernel using the changed files from System 76's repo.
This is not nearly as difficult as it sounds. The process described in the Fedora docs, under Building a Custom Kernel, is easy enough to follow. In my case, it was even easier. I unpacked the kernel source by following the steps down through "Prepare the Kernel Source Tree" and then copied the source for the new "module" into drivers/input/mouse, replacing just the elantech.h and elantech.c files. I don't really care about getting an RPM, so I just built the kernel"[URL]..
I've bought a Asus EEEpc 1005 PX and trired to install Ubuntu netbook. But I found that wifi is not working. It's not detecting the wifi cards.I tried ifconfig, and it is showing me,When I tried LSPCI it's showing me
Ethernet controller: Atheros Communications Atheros AR8132/L1c Gigabit ethernet adapter (rev c0)
Network Controller: Atheros Communication inc. Device 002c (rev 01)
how can i set up the wifi here.(I tried with Meego, and Meego detected the wireless autometically..But I want to use Ubuntu)
So I have Ubuntu 9.10 up and running on my T91MT and everything but the wireless is working. The chip is an AR9285 and everything I've read online says I just need to install the backport modules to make it work, however I have done this and it still doesn't work! My wireless reads as "disabled" when I try the nm-applet.
Also I can confirm the wifi card works under Linux because it works fine under Jolicloud and Elive live CDs...
I have eventually (a week's work) got my Ubuntu 10.04 to recognise my Asus N13 WiFi dongle (had to compile the source from Ralink with the "y" against the two things it tells you to if you want network manager to work (source that came with dongle wouldn't compile) and then set up rules (for some reason the driver - rt2870sta - wouldn't recognise the dongle until the rule about the vendor and product ID was in place; and the drivers that come with Ubuntu wouldn't recognise it even with the rule in place)).
Big thank you to chilli555 for all of the posts that got me this far.I would like to use the Network Manager app that comes with Ubuntu, to control the dongle. At the moment it will aknowledge when the driver has been loaded (have to do a modprobe), but does not "see" any of the many WiFi routers around my house, so I can't click on one to select one.
My only guess on this is that, to get the dongle to work I copied the config file that is part of the driver source files into /etc/Wireless/RT2870, and this is getting in the way. However, I have tried removing it and the network manager still doesn't work. Or is it because the network manager needs the dongle to be called "wlan0" and it's called "ra0"? If so, can you aliase this?
I've got an Asus EEE 1000HE, and it's worked fine for a long time with the EEEBUNTU distro (a distro based on Jaunty (i think) with a custom kernel). Unfortunately, Eeebuntu is no longer maintained, so I recently did a clean install of Ubuntu 10.04.2. I am now unable to get my wifi to work reliably.
The wifi tries to connect for a while, then pops up the "Wireless Network Authentication Required" window. If I hit "connect" it will try again for a while, then pop up the window. Etc. Note I know that my connection information is OK. I haven't mistyped the password (see below). Also note that the wifi antenna is turned on. For example, iwlist scan is able to find my network.
There is a weird twist though: The netbook is always able to connect through an ethernet cable on eth0 just fine. If I boot the netbook with the ethernet cable plugged in, the wifi instantly connects as well! I can then unplug the ethernet cable (eth0 goes away), but I am still able to use the wifi connection for about 5 minutes before it disconnects, and goes back to trying and failing to connect.
This behavior is 100% replicable--the wifi always works fine (for about 5 minutes) if it boots with the ethernet cable plugged in. Very rarely, the wifi will also connect on boot without the ethernet cable, but that is not replicable.
Other EEE netbooks seem to have issues with multiple wireless drivers, like in this thread. Perhaps something similar is happening here? My card seems to be using rt2860sta as a driver. I tried blacklisting it, to see if another driver was trying to load instead, but that just negated my wifi altogether. (It's unblacklisted again)
My router is a very reliable Linksys WRT54GL with factory firmware which has never been flaky.
I'm at my wit's end. This netbook will be useless without wifi.
Below is the suggested information for a first post:
Here's lspci (note there is nothing listed as "Wireless Brand" to grep out):
Code:
lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
[Code]....
I have a backup HDD with a different distro for my laptop and i can boot into it via external usb or if swapped into the laptop. This HDD/install in question is debian testing and was working fine, the issue arose suddenly. I was first suspecting a failure of hardware somewhere on the motherboard, but the hdd i was using with an external usb adapter also works when installed into the machine. also, the HDD is recognized once i have booted using the external HDD and distro, but it is not recognized by the bios. so i dunno, my first guess is something became corrupt within the testing install, but i guess its also possible that there is some wrong with the HDD but thats not immediately apparent as all the data is still accessible.
Should also note that the HDD with testing on it is also recognized when connected via the external usb adapter, while booted from alternative distro/HDD.
Also. just tried this, but i can get the testing HDD/disto to boot if connected externally. it was going pretty quick, but there i did catch a line about a corrupt filesystem. any commands to run to see what might be going on?? log files to look at?
Im a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopś internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...