Debian Hardware :: Failure To Pair Bluetooth Mouse In Squeeze

May 9, 2011

I recently upgraded this machine from Ubuntu Maverick 10.10 to Debian Squeeze, x86_64, by wiping the root partition (I kept my backup and my home partitions). Everything has gone OK except this: for whatever reason I cannot pair my Microsoft Bluetooth Notebook Mouse 5000 with this machine any longer. In bluetooth-applet I can see the mouse when I go to pair it with the machine, but it simply times out and the pairing fails.

The target mouse definitely used to work in Ubuntu, so I doubt it's a problem in the physical layer. I tried another Bluetooth mouse (a Rocketfish/BestBuy POS), and it doesn't pair either. The Microsoft mouse I would like to use pairs just fine with my Debian squeeze laptop, but they're not using identical Bluetooth adapters as far as I can tell. lsusb reports that I've got a Broadcom BCM2210 in my workstation (the subject of this post), and lsusb on my laptop reports some kind of Broadcom Bluetooth adapter, but doesn't report its chipset.I'd really like to stay on squeeze if possible, but my googling for this has only led me to old documentation, or stuff that applies to wheezy or sid.

View 4 Replies


ADVERTISEMENT

Debian :: Bluetooth Doesn't Pair, No Agent Available For User Confirm?

Jun 15, 2010

I'm using debian lenny (5.0.4) on 3 different laptops, two fresh installs and one was installed with etch and then updated.In the one that has been updated pairing works without any problem, while in both the others it doesn't work. I can see this on syslog when I try pairing from the phone:Jun 15 10:31:02 robertof-lt hcid[17891]: io_capa_response sba=00:22:5F:00:C2:1F, dba=C0:38:F9:D3:29:A3)Jun 15 10:31:02 robertof-lt hcid[17891]: io_capa_request (sba=00:22:5F:00:C2:1F, dba=C0:38:F9:D3:29:A3)Jun 15 10:31:04 robertof-lt hcid[17891]: No agent available for user confirm request

View 1 Replies View Related

Debian :: How To Pair Bluetooth Keyboard Via Command Line On Jessie

Mar 27, 2015

I installed the Open Source Media Center (OSMC) on my Raspberry Pi 2. It's based on Debian Jessie. I bought a Blueooth Keyboard (Keysonic KSK-3211) and an USB-Bluetooth adapter (CSL Bluetooth Stick Nano). And now I am looking for a way to pair the keyboard with the raspberry via command line.

I'm new to all this bluetooth stuff in debian. It's the first time I try to install it. As far as I've understood I need an agent that is started with the pairing PIN. Then I type this PIN at the keyboard and that's it. Am I right?

The problem is, that every agent I've found in howtos or descriptions like bluez-simple-agent or bluetooth-agent (like described here [URL] ....) is not installed (and as far as I know can't be installed) under Jessie.

The bluetooth adapter is recognized

Code: Select allosmc@osmc:~$ hcitool dev
Devices:
        hci0    00:1A:7D:DA:71:0C
the keyboard is found
Code: Select allosmc@osmc:~$ hcitool scan
Scanning ...
        00:12:A1:70:42:28       Bluetooth Keyboard

And I can ping the keyboard

Code: Select allosmc@osmc:~$ sudo l2ping 00:12:A1:70:42:28
Ping: 00:12:A1:70:42:28 from 00:1A:7D:DA:71:0C (data size 44) ...
0 bytes from 00:12:A1:70:42:28 id 0 time 14.82ms
0 bytes from 00:12:A1:70:42:28 id 1 time 9.91ms
0 bytes from 00:12:A1:70:42:28 id 2 time 32.62ms
0 bytes from 00:12:A1:70:42:28 id 3 time 28.81ms
^C4 sent, 4 received, 0% loss

So everything seems to be ok ... but I can't find the command for pairing the keyboard. Looks like something changed in Jessie so that the old tutorials are outdated.

View 2 Replies View Related

General :: Bluetooth Can't Pair Phone

Jan 23, 2010

I recently installed openSuse 11.2 with KDE4.3...When I try to pair my phone, the bluetooth manager finds my phone. However when I try to connect it says "your phone doesnt support input". My phone is set to "discoverable" (ie. visible to all). But, it just wont work.I had it working on previous systems. But not this time.

View 1 Replies View Related

Fedora :: How To Pair Bluetooth Device Without Pin Code?

Jul 12, 2010

I have laptop with bluetooth and I bought PS3 bluetooth remote. In windows this remote is working with EventGhost and I would like to use it in Fedora as well. This remote has to be paired without a pin code, which is how I paired it in windows.In Fedora, however, there is no such option "no pin" when using a standard way to connect bluetooth device.How can I pair this remote in Fedora?

View 11 Replies View Related

Ubuntu Networking :: Pair Bluetooth Rocketfish Keyboard

Feb 19, 2010

I am able to pair a rocketfish bluetooth mouse, but I am not able to pair the keyboard. I was wondering if anyone knew the correct pin. Or if anyone knew what I need to do.

View 5 Replies View Related

Ubuntu Networking :: Unable To Pair Bluetooth Dongle ?

Jul 3, 2010

I have a laptop with no bluetooth on it.So i bought a bluetooth dongle.It works flawlessly under windows but i am having a problem with it under Ubuntu (As well as other Linux distros). As soon as i plug the dongle i see a bluetooth icon in the Notification Area.

When i click on it and choose setup new device....its scans and shows all the bluetooth devices like my Nokia 5800 xpressmusic cell phone but when i try to pair it simply fails....

I have tried all the Pin codes available and even tried the custom pin option but still no success. By the way right now i am using Ubuntu 10.04..i have also tried it with other linux OS but still the problem remains....

View 2 Replies View Related

Ubuntu / Apple :: Can't Get Bluetooth Keyboard To Pair In Maverick?

Oct 13, 2010

I think my computer must be haunted, as I've so far failed at 3 different ways of installing Maverick on my 2007 aluminium imac! I've written off using a VM, and I'm currently stuck trying to make a dual boot setup.

So I've followed the guide at [URL].. and got as far as rebooting with the CD in, and selecting Ubuntu, but then when everything loads I'm left at the screen where I can select try or install, with no way of selecting either as my mouse (apple bluetooth mighty mouse) and keyboard (apple bluetooth wireless aluminium keyboard) don't seem to be connected. I've got past this point by hitting random keys after booting and selecting the CD - this takes me into a more basic looking menu where the keyboard does still work and I can select install, try etc.

So I can get as far as selecting try, and get a working Ubuntu desktop. However, when the desktop loads, my keyboard and mouse are again not working. By connecting a USB keyboard and mouse, I'm able to get my mouse to pair, using the bluetooth menu and going through the setup. However, I'm stuck trying to get my keyboard to pair.

Going into set up new device and searching initially shows up my keyboard, then it disappears. If I wait it randomly comes back and disappears again. If I click on next whilst it is available, I can get as far as putting in a pin, but when I press enter it says Failed..

Sorry for the rambling post - I basically have 2 questions: 1- Is it expected that bluetooth keyboards and mice won't work during the installation menus? Half my problem is that I don't know what should be working and when (should I have to boot into the trial installation and setup the keyboard and mouse, or should it be set up automatically?).

2- Has anyone else seen the same problem with the apple wireless keyboard failing to pair? I've searched the forums and google, and found lots of people with problems with bluetooth keyboards, but none which seem to match what I'm seeing. I don't know if there's any point in pressing on with the installation using the USB keyboard and mouse in the hope that things will work in the full install, or if they don't work in the trial install then thats my lot.

View 6 Replies View Related

SUSE / Novell :: Pair Phone Without Downgrading Bluetooth Packages?

Jan 23, 2010

I recently installed opensuse 11.2 with Kde4.3.I am having trouble with the bluetooth. I'm trying to get kanyremote to work, but i cant pair my phone.I searched google and the only option I see is to downgrade bluetooth.Can anyone help me pair my phone without downgrading my bluetooth packages?

View 1 Replies View Related

Hardware :: Bluetooth On Macbook With Debian Squeeze?

Mar 31, 2011

I have an old(ish) Macbook laptop. It comes with built-in bluetooth. The box says "Built-in Bluetooth 2.0 + EDR (Enhanced Data Rate)".

I'm not sure if it interfaces via USB or not, but I do not see any bluetooth stuff via lsusb. I do see bluetooth stuff when looking at dmesg. But when I look at hciconfig I see nothing at all. Here's what I get with the various commands:

#lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 05ac:8240 Apple, Inc. IR Receiver [built-in]
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

[Code].....

View 6 Replies View Related

Debian :: Boot Failure After Squeeze Install?

Jun 5, 2010

I cannot boot after installing Squeeze. /home partition is missing.

Here is the related information.

df -h

Code:
Filesystem Size Used Avail Use% Mounted on
/dev/hda1 6.5G 4.5G 1.7G 73% /
tmpfs 1.7G 0 1.7G 0% /lib/init/rw
udev 1.7G 196K 1.7G 1% /dev
tmpfs 1.7G 0 1.7G 0% /dev/shm

[Code].......

View 3 Replies View Related

Debian :: ASUS USB-BT211 Bluetooth Dongle - Working In 6.0 Squeeze 64 Bit ?

Jul 26, 2011

I purchased a ASUS USB-BT211 Bluetooth Dongle and I'l like to get it to working in Debian 6.0 Squeeze 64 bit.

uname -r gives....

I plugged in the USB Dongle:

lsusb gives....

lsusb -v -d 0cf3:3000 gives...

cannot read device status, Operation not permitted (1) larry@debian:~$

What do I need to do to get the Bluetooth Dongle Functional?

View 3 Replies View Related

Debian Installation :: Squeeze Installer Yaboot Failure

May 13, 2010

The installer for powerpc is broken in Squeeze. If yaboot is installed, it will break the whole boot process. I don't know exactly what goes wrong but it is a serious bug. I tried many times until I found out that yaboot is broken in Squeeze. In Lenny it still works luckily, so I could get something back after a complete sweep of my hard disk (the Lenny installer could not do anything with the ext4 partition of Squeeze as it is not supported in Lenny, so trying to put yaboot back did not work from there). Let this be a warning to people and a reminder for developers that there is a serious bug in yaboot.

View 2 Replies View Related

Debian Hardware :: Bluetooth Firmware With Windows 7/Squeeze Dual Boot?

Aug 3, 2010

This problem goes back to when I first purchased my laptop 4 years ago: Dell Precision M90. It came with Vista, but I wanted Ubuntu on instead. In order to get bluetooth to work, I had to downgrade the firmware. This is all fine and means bluetooth works in XP too. However, now, I have a dual boot with Windows 7 and Squeeze, I use Vista drivers (as Dell don't provide 7 drivers) and this has upgraded the firmware, and broken bluetooth in Squeeze. How can I get bluetooth working in both Squeeze and Windows 7? Could changing the hardware help? If so, what to?

View 2 Replies View Related

Debian :: Bluetooth Mouse Doesn't Work In Wheezy

Aug 3, 2011

I was in 2.6.38.-2-amd64 and it was upgraded to 2.6.39-2-amd64. After the upgrade, every reboot disables the bluetooth mouse. There is a message from the panel with a bluetooth icon
Bluetooth Device
Authorization request from Logitec mouse...
check authorization

I push the buttons on my mouse and the button on the dongle to try and get them to pair, but, the dongle does not work. It is not scanning when I push the connect button.I unplug the usb dongle, and plug it in again, and this time I am able to pair them, and the mouse works. But, I have to do this every time I reboot which is a pain. I found that in the previous kernel, The Bloothtooh package is 4.91-1, but it has been upgrade to 4.91-2. So, this is creating the problem.

View 14 Replies View Related

Debian Hardware :: Characters Randomly Written When Bluetooth Mouse Is Paired

Nov 16, 2014

I have an ASUS Zenbook UX31E with Debian testing and LXDE as a Desktop environment. I have a Logitech T630 Mouse that I connect through Bluetooth. When the mouse is paired I can use it properly but I get random keys typed in my desktop such as "1", "2" or "/".I am a regular user of Debian, and I have being using the system for several years now even worked as sysadmin for sometime. However I do not have much knowledge about Bluetooth devices management. I found no information on this issue on the internet and I do not know where too look for more info on my own system. Here is some info I got:

Code: Select all:~$ hciconfig -a hci0
hci0:   Type: BR/EDR  Bus: USB
        BD Address: 74:2F:68:CC:5C:74  ACL MTU: 1022:8  SCO MTU: 183:5
        UP RUNNING PSCAN
        RX bytes:606 acl:0 sco:0 events:36 errors:0
        TX bytes:939 acl:0 sco:0 commands:36 errors:0
       
[code]....

I have tested "blueman-applet" and "bluedevil" as desktops applets and pairing through console gives same results, so it seems like a problem with the bluetooth communication.

View 0 Replies View Related

Debian Installation :: Plug USB Mouse And Keyboard In After This Failure Which Then Works

May 10, 2011

I'm trying to net install Wheezy on an Abit IC7-G PIV system. I tried this months ago but the problem still exists. This is not so much an installation problem but after installation when it boots, I lose PS/2 mouse, PS/2 keyboard and network. I get:

startpar. service(s) returned failure udev ... failed I can plug USB mouse and keyboard in after this failure which then works. There is nothing wrong with the hardware. It works fine on other systems. Squeeze works perfectly.

View 7 Replies View Related

Debian Hardware :: Microsoft Designer Bluetooth Mouse System Hang When Pairing

Aug 1, 2015

Just picked up a Microsoft Designer Bluetooth Mouse.Whenever I try to pair it, my system hangs and I have to hard power it down. The mouse is Bluetooth 4.0, but my Bluetooth connectivity is provided by my Intel Wireless 3160 card which does support Bluetooth 4.0.I'm using Blueman as a front end, and one other thing of note is that it shows as "Unknown" after a scan.If I need to return it, I need to return it, but it seems like a good mouse and I'd like to keep it if I can make it work.

I've took this out of syslog:
Code: Select allAug  1 14:58:04 Noah-LEMUR kernel: [  317.772054] BUG: unable to handle kernel NULL pointer dereference at 0000000000000398
Aug  1 14:58:04 Noah-LEMUR kernel: [  317.772090] IP: [<ffffffff81569f7e>] mutex_lock+0xe/0x30
Aug  1 14:58:04 Noah-LEMUR kernel: [  317.772113] PGD 0
Aug  1 14:58:04 Noah-LEMUR kernel: [  317.772123] Oops: 0002 [#1] SMP

[code]...

View 0 Replies View Related

Multimedia :: Configure A Serial Mouse On Debian Squeeze?

Mar 3, 2010

I have a very old Pentium 3 that don`t have USB or PS2 suport.
I need to configure a serial mouse.
I did it on debian etch editing xorg.conf. I chage the mouse protocol to "Microsoft" and it works normaly.
But on squeeze it does not exist!

How can I configure it?

View 13 Replies View Related

Hardware :: Mouse And Keyboard Not Working Debian Squeeze With Kde?

Feb 1, 2010

I have debian with kde on a laptop with a built in ps/2 keyboard and touch pad mouse which have been working without problem since i bought the computer. However, recently i booted the computer up and all of a sudden the mouse and keyboard are not functioning. I know it is not a hardware problem because i can type in the BIOS password, make the selection between normal and recovery mode in grub, and can type in all of my passwords to unencrypt my hard drive.

Also, it recognizes the keyboard all the way up until the point where kde starts, at which point it loads a login screen with the mouse and cursor on the screen, but no ability to type, not even caps lock or ctrl+alt+f1 to switch to console mode. does anyone know why this is? I have performed not updates and have not changed the configuration of my computer so i am not sure why this would happen.

P.S.1 out 15 times when i load the part where i need to type in the passwords to unencrypt the hard drive the keyboard will stop working then instaed of with kde.

View 8 Replies View Related

Debian Installation :: Mouse Not Recognized After Lenny To Squeeze Upgrade

Feb 17, 2011

my mouse wouldn't work in any fashion after going through most of the install process from Debian Lenny to Squeeze (couldn't click, move the mouse, etc. under both Compiz and Metacity). My system is a Lenovo ThinkPad T61 laptop; I keep the touchpad disabled, but the button mouse (TrackPoint) wouldn't work either. I was following the instructions here:

[URL]

So, the first thing I did was run the following commands, as it says to do:

# apt-get upgrade
# apt-get install linux-image-2.6-686
# apt-get install udev

Then, I rebooted my machine into the new kernel (2.6.32-5-686). I got a ton of udev warning messages at startup (all along the lines of "SYSFS{}= will be removed in a future udev version, please use ATTR{}= to match the event device, or ATTRS{}= to match a parent device, in something-or-other" - details can be provided if needed), but got a functioning prompt. I logged in, ran startx, and everything worked except the mouse, which couldn't do anything - as if it wasn't recognized at all. Switching window managers from Compiz to Metacity, as mentioned before, didn't help. "modprobe psmouse" revealed that that module was correctly loaded.

Rebooting into my old backported kernel (2.6.32-bpo.3-686) restored mouse function, although I still had the udev warning messages (so maybe those aren't relevant, I don't know). Apparently, something about the different kernels is causing the problem, but I'm not sure what - any thoughts? I haven't wanted to complete the upgrade with "apt-get dist-upgrade" without knowing that I'll have a working mouse, since I need a functional GUI at the moment and don't have a good way of fixing it if I trash it.

View 4 Replies View Related

Debian Multimedia :: Keyboard And Mouse Freeze After Login In Squeeze

Feb 10, 2011

I have a problem with mouse and keyboard. Both freeze within 30sec to half an hour after logging into squeeze 64bit (using gnome). My hardware is Asus P7P55D EVO (tested with linux according to ASUS) with Intel i5 760 CPU. I use IBM keyboard and Trust PS2 mouse. I also have MSI HD4350 graphics card, that was at least listed on Ubuntu to be supported, worked fine also with Lenny.

When using same combination with Lenny (64-bit) I never found any problem with either keyboard nor mouse, even running long nights. However there was need to upgrade to Squeeze since it has newer kernel supporting the sensors on board my MB. I used same mouse and keyboard also on Ubuntu 9.10 and had never problems. However when I upgraded to new MB I started with Ubuntu 10.04 64 bit version and experienced same keyboard and mouse freeze as I have now in squeeze. Only way out from this status is hard reset using PC reset button.

I connected with putty to my linux box and found following (while the linux box was on frozen state) from dmesg on keyboard: :/var/log$ dmesg | grep -i keyboard [ 1.064628] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0

View 12 Replies View Related

General :: Invisible Mouse Cursor After Updating Debian Squeeze?

Mar 26, 2011

I have just updated Debian Squeeze and my mouse cursor is invisible. However, it still functions... I can right click and get a menu, clock on things and get the normal functions.

I have filed a bug report and found one other bug report on this but haven't found a fix or any other info.

View 2 Replies View Related

Debian Configuration :: PS2 Mouse On Laptop Compaq Evo N610c, Squeeze - Doesn't Work?

Mar 2, 2011

how to fix the detection of ps2 mouse under Debian Squeeze? It is the optical mouse with wheel, red light shines, but mouse doesn't work.

View 14 Replies View Related

Debian Configuration :: KDM "failure" On Boot - Squeeze

May 26, 2010

Hardware at issue is an nVidia GeForce 9600 GT. Issue occurs regardless whether the driver is downloaded and installed from nVidia, or installed via Synaptic courtesy of the new dkms package in the repositories.

It should also be noted that the issue only arose after an update today, as follows:

I do not believe it is related to the last three items in that list. Because everything worked perfectly before todays update, it would appear that one of those other updates is causing KDM and nVidia to not want to co-operate with each other.I also notice that, new to the boot sequence, the system is booting with "concurrency" - never seen that scroll by before - which may have something to do with it too.

OK, what happens. KDM "fails" to start when booting the computer. Symptoms : At the appropriate spot in the boot sequence, the screen goes black (as usual), but then, instead of the cycling cursor followed by the logon screen, the nVidia logo appears, and after about 7 or 8 seconds, the screen goes black for about a second, then drops me back at the console. From there, I can log in as root.

Now, the thing is, KDM is actually running, but using <control> <alt> <F7> only brings me to a blank black screen. By issuing the command /etc/init.d/kdm restart, I come up to a normal logon and can proceed as usual. As well, if I delete xorg.conf, system boots OK.

Looking at the system log, we find :

And then some way past that we get :

Should mention that was using the latest stable driver from nVidia (195.36.24), but in the hope that maybe something in the latest beta may solve the issue, installed that, but the answer is nope And yes, completely uninstalled the nVidia drivers between each test of the nVidia driver, the same driver in the repositories and the latest beta driver, before anyone mentions.

View 3 Replies View Related

Debian :: Make A Boot RAID0 LVM On A Pair Of SSDs

Aug 20, 2015

I would like to make a boot RAID0 LVM on a pair of SSDs (sdc and sdd). The system is already running off of a HDD. I built the RAID0 through the Asus BIOS on the Intel controller. I see:

# cat /proc/mdstat
Personalities : [raid0]
md124 : active raid0 sdc[1] sdd[0]
59346944 blocks super external:/md126/0 32k chunks
md125 : active raid0 sda[1] sdb[0]
222715904 blocks super external:/md127/0 32k chunks

[code]....

My challenge is that when I open Gparted, it only show one disk at a time. I would like to learn how to use Gparted to partition this RAID0 with a UEFI sector and LVM for the rest.

View 2 Replies View Related

Hardware :: Bluetooth Breaks After Using Mouse In Other OS

Oct 17, 2010

If I use my bluetooth apple Mighty Mouse in a LiveCD of Ubuntu, or in mac OSX, when I next boot linux from disk, the mouse won't connect to it. I do not know if it is something about the mouse that is changing or if it is something on the linux side. This has just happened to me again, and I am sure that the mouse was working before.

View 2 Replies View Related

OpenSUSE Hardware :: Cannot Setup The Bluetooth Mouse

May 18, 2010

I've just set up dual boot Win 7 with openSUSE 11.2 but unfortunately I have run into a couple of problems. One of them is that I cannot set up my Bluetooth mouse, which works under windows.

I am typing this from Windows right now (wireless is not working either) so I cannot reproduce the exact steps but anyways, when I try to add a new Bluetooth device it first finds my mouse, and keeps searching, and then removes the mouse from the list, and keeps searching, then it finds it again, ... and it goes endlessly. If I select mouse on the list and click forward on the next screen I get an error saying that the mouse was not set up.

View 4 Replies View Related

Ubuntu :: Attach Dell Bluetooth Mouse ?

Oct 17, 2010

How to attach dell bluetooth mouse in ubuntu?

View 1 Replies View Related

Ubuntu :: Bluetooth Mouse Does Not Move The Pointer

Jan 26, 2011

I have an issue with a bluetooth mouse. The mouse connects with the pc normally, and the bluetooth manager reports that the bluetooth device sends data. However, the mouse does not move the pointer, or seems to do any kind of effect on the pc.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved