I have run into a bit of a problem. Trying to get a new install of Centos onto a pair of 750GB drives.
These were once part of a software raid setup. The installer reconises them as a ddf1 raid set. so it does not list the drives as 2 individual drives. I can get around this with the nodmraid
i find this is an issue which might be tiresome for everyone except for those experts. Esp. for the computers which are dual booting(both windows xp and centos installed in the same computer), that when we are in CentOS we need to switch onto windows immediately. and vice versa. i see this is possible only by shutting down the centos/windows and then restarting onto the other OS.
Can anyone tell me the the solution to work simultaneously both xp and centos without the need of shutting down and restarting There maybe or may not be the solution...but i find the pleasure to know if there is for example, remote desktop connection in windows xp, is there any solution, we can work on windows via centos or vice versa ( in the same machine),
Since RHEL is similar to CentOS posting it here.
Upon booting from DVD, i get the below error: "CentOS CD Not found in any of the media drives. Please insert CentOS CD and press OK."
I have IDE Sony DVD RW AW-G170.
BIOS Setting:
Downloaded the CentOS-5.4-i386-bin-DVD image from centos.org from DVD.torrent using bittorrent file.
When booting from the DVD, it gives me the boot prompt:
Upon pressing enter, the log messages of the boot detect the media drive as: hdc: Sony DVD RW AW-G170 IDE ATAPI CD.
The below steps occur:
1) Select the keyboard type: selected us
2) Select the Language : selected us
3) Select the image:
- Local CDROM
- Hard Drive
- NFS Image
...
...
selected Local CDROM
Then the above error "CentOS CD Not found in any of the media drives. Please insert CentOS CD and press OK."
The booting steps does not ask the for media check step.
The below methods have been tried to solve the problem:
- Burnt the image in another 2 DVDs but the same error "CentOS CD Not found in any of the media drives. Please insert CentOS CD and press OK."
- Upon burning the DVD image , selected the DVD read speed: 8x. Upon burning the DVD selected 18x for burning. and then tried to boot with that DVD
- At the boot prompt entered : linux hdc=cdrom replaced hdc=hdb but the error remains.
I've got a some new servers populated with Hitachi 3tb disks. The disks use the GPT partition table with normal size sectors. I was able to complete an install by using Ubuntu Natty to format the drive and install Grub2, then run a patched version of the CentOS installer following these instructions here: [url]
It works, but I've installed Ubuntu on another partition just in case I need to make any changes to the disk. I'm wondering if I can upgrade to Grub2 and install GPT aware partitioning tools so that I don't have to reboot into Ubuntu to make those changes.
The first server I installed installed fine. The second server, installed with the same config, went to "kernel panic not syncing no init found try passing init= option in kernel" error. I tried reinstalling but it keeps going to that error after install reboot. The storage is ISCSI connected via Intel Server Adapter, which allows it to boot from ISCSI. Not sure if that's the cause for the problem, but the first server is connected to the same ISCSI and installed just fine.
Is there a way that I can make sure ISCSI module installs during installation? Although I think it is installed since it's able to copy the files and setup /dev/sda. I just wana make sure that it installs during setup.
I have tried to install debian 5.0 and 4.0 without any luck. I have both tried virt-manager and virt-install with both debian-501-i386-netinst.iso, and full dvd. I't always gives me the same error:Starting install.Could not find an installable distribution at '/xen/debian-501-i386-netinst.iso'
[Code]...
i didnt find a solution to a display problem im having. my server mobo is an asus k8n-dre with built in video. after the install(using built in video) the screen dosnt display fully as in black sections on the left and top of the screen. from the searching i did i found something about an "xrandr" command that would let me change the video settings but it didnt do anything with the black areas when i tried it. i also have a nvidia geforce 9500gt video card so i changed the jumper to boot from it and tried again. the black sections are still there but the centos display covers much more of the screen now. theres still about a third of an inch gap on the left hand side and about 1/4 of an inch on the top. ive also tried updating the software to see if it may be a driver issue but no luck. anyone know how or if it can fit to full sceen? the screen displays up to 1440x900 if im not mistaken but with the built in video it gave me lots of display options including the 1440x900. after changing to the nvidia card it only shows 800x600 and 640x480.
View 5 Replies View RelatedI am trying to install CentOS 5.2, and the installation ran out of disk space after running for about 2 hours.I checked the FAQ, and it said 1.2 GB. The disk is 3 GB. The default install was selected, and I think that it checks for sufficient available disk space before installing. Still, it ran for quite a while before announcing that it was out of disk space.The Installation Guide is not very helpful, since there is a blank page where the disk space requirement is supposed to be. I just picked the default installation. A search of the forums on "not enough disk space" did not return much.
View 13 Replies View RelatedI have successfully installed CentOS 5.4, and after choosing it from the GRUB menu, I am getting the following error message:1706-Smart Array Controller Extended BIOS Data Area Memory Corrupted. Int 13h BIOS Cannot Continue - System Halted.I'm using two SAS disks that came along with the server, left the default RAID configuration (1+0) on a P410 controller
View 5 Replies View RelatedI've got a box (prev used for WinXP) with 2GB Ram and a new 500GB HD to throw in there.Noticed on the Wiki CreatingUpdateMedia and reading as much as I can ramping up for this.I'm curious how I should partition this disk, and what other decisions I'll need to make on install.I see quite a bit of interest also in virtualization, and if I find a need, this could be useful too.Kernel upgrades?how to do? Does the disk have to be wiped or just use an alternate boot device to replace K on HD? I have a tech background in programming and some solaris, but *nix has grown up in the last 5 years.Hopefully devices will function and networking connectivity can be acheived without too much troubleshooting.
I'm doing this in part to be more educated, especially in the new world of web-hosting where you have a virtualized box, root and shell access, and need to manage it yourself. Beyond that even, my goal is to be able to work on my web-host by setting up a remote linux desktop, and I'll be looking for ways to configure that. There are clients out there (VNC, etc), but I'm not sure on the host-server configuration, and also the port-forwarding setup on my local router.
[URL]VMware Workstation 7.0.1 Release Notes has a list of supported OS:[URL]According to that, RHEL 5.4 is listed as supported for both host andguest but CentOS 5.4 is only for guest. This is quite strange and, ifit is true, that could be a serious issue.I succeed to install vmware workstaion 7.1 on centos 5.5, but have run-time error:
[root@ ~]# /etc/init.d/vmware start
Starting VMware services:
VMware USB Arbitrator [ OK ]
[code]....
I have a problem with a VM running Centos 5.3 on a Centos 5.2 hypervisor. Any kernel install makes the system unbootable and I have to copy an old /boot directory to get it to boot again. After some investigation I found that grub was always failing. These are the partitions I have. xvda is the OS virtual drive. xvda1 is the /boot partitition and xvda2 is the LVM partition. A standard default install.
cat /proc/partitions
major minor #blocks name
202 0 14648448 xvda
202 1 104391 xvda1
202 2 14538825 xvda2
202 16 195313152 xvdb
202 17 195310206 xvdb1
253 0 11337728 dm-0
253 1 2031616 dm-1
253 2 190840832 dm-2
Apparently, this file could be suspect. But it seems to be OK according to what I have read.
cat /boot/grub/device.map
# this device map was generated by anaconda
(hd0) /dev/xvda
If I try to re-install grub I get...
Attempt 1)
grub-install hd0
/dev/xvda1 does not have any corresponding BIOS drive.
Attempt 2)
grub-install /dev/xvda
expr: non-numeric argument
/dev/xvda1 does not have any corresponding BIOS drive.
Attempt 3)
grub-install --recheck hd0
Probing devices to guess BIOS drives. This may take a long time.
No suitable drive was found in the generated device map.
Reverting to backed up copy.
Attempt 4)
grub-install --recheck /dev/xvda
Probing devices to guess BIOS drives. This may take a long time.
No suitable drive was found in the generated device map.
Reverting to backed up copy.
Attempt 5)
grub
Probing devices to guess BIOS drives. This may take a long time.
GNU GRUB version 0.97 (640K lower / 3072K upper memory)
[Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename.]
grub> root (hd0,0)
root (hd0,0)
Error 21: Selected disk does not exist
This is my grub.conf file...
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE: You have a /boot partition. This means that all kernel and initrd paths are relative to /boot/, e.g.
# root (hd0,0)
# kernel /vmlinuz-version ro root=/dev/VolGroup00/LogVol00
# initrd /initrd-version.img
#boot=/dev/xvda
default=0
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title CentOS (2.6.18-128.1.6.el5xen)
root (hd0,0)
kernel /vmlinuz-2.6.18-128.1.6.el5xen ro root=/dev/VolGroup00/LogVol00
initrd /initrd-2.6.18-128.1.6.el5xen.img
I have recently lost quite a bit of electronics around the house to a power surge/lightning strike (all items were on APC backups). The drives from my server were undamaged and I have a new server to host them in. I am having a hard time getting the new server to boot up with the old drives (trying to avoid a fresh install/rebuild of server). The hardware is very similar but not identical. At this point it gets to the following during the boot process:
Scanning and configuring dmraid support devices
md: Autodetecting RAID arrays
MD: autorun ...
MD: ... autorun DONE.
MD: Autodetecting RAID arrays.
[Code]...
I'm new on Dell PowerEdge 2900. I dont know how to install centOS 5.2 on it. whice OS type that I should select. at first I select RH enterprise 5 and it format HDD. already and I put centOS 5.2 in, but it was deny and eject that cd. when I power off it shown that
"root(hd0,1)filesystem type is ext2f2,partition type0x83
kernel/linux/vmlinz%(ksLocations)
Error is : file not found
press any key to continue"
I am trying to do a basic install of CentOS 5.4 on my embedded computer. It is a Linutop 2 system with a AMD Geode 800MHz CPU and 512Mb Ram. Have installed an IBM 40Gb 2.5" HD for OS storage. I am doing the install procedure in text mode. Everything goes as planned until I get to the package selection.
1. Booting from (i386) DVD with "linux text" parameter.
2. Skipping media check.
3. Selecting "English" install language.
4. Selecting "DK-latin1" as keyboard layout.
5. Selecting "Remove all partitions and create default layout" and selecting "no" to modifying partition layout.
6. Selecting "yes" to configure "eth0" and mark to enable "IPv4" on boot.
7. Selecting DHCP for IP configuration and Manual host name.
8. Setting time zone to "Europe/Copenhagen".
9. Setting root password to a 16 digit alphanumeric pass-phrase.
10. De-selecting "Desktop - Gnome" (no other entries selected).
When the system is checking for dependencies, an exception
Traceback (most recent call first):
File "/usr/lib/python2.4/site-packages/yum/packageSack.py", line 426, in returnNewestByName
raise PackageSackError, 'No Package Matching %s' % ui_pats
File "/tmp/treedir.22057/instimage/usr/lib/anaconda/yuminstall.py", line 1072, in getBestKernelByArch
pkgs = ayum.pkgSack.returnNewestByName(pkgname)
[Code]...
I've been trying for the past week to install an icecast server on my centos 5 VPS hosted through phurix.
I've tried compiling it, installing it from RPM. but im getting nowhere. Has anybody had any luck installing it, who wouldn't mind explaining how they went about it?
I've searched google for hours on end and all I can come up with is generic cent os 4 guides that just wont work. Im not the best when in comes to linux. I do a great job of copying and pasting to a shell prompt and can use ftp etc.
if this is any use.. heres the last output from my last attempt and compiling it...
[root@vps613 icecast-2.3.2]# ./configure --prefix=/usr/local/icecast
checking for a BSD-compatible install... /usr/bin/install -c
checking whether build environment is sane... yes
checking for a thread-safe mkdir -p... /bin/mkdir -p
checking for gawk... gawk
checking whether make sets $(MAKE)... no
[Code]...
How do I know what sound system my Centos 5.5 install is using and how would I configure which soundcard output to use? I want to use the digital coax output from my M-Audio PCI soundcard, which appears to be detected and loaded. When I launch MPD, it autodetects an alsa sound system, but programs like alsamixer don't exist and I can't hear any sound out of the digital coax output. I haven't checked the 3.5mm stereo out yet.A little confused as to which documentation to be looking at at this point.
View 9 Replies View RelatedI am trying to run though the qmailrocks setup on a centos 5.5 and I am running into an issue when trying to telnet to port 25:
telnet localhost 25
Trying 127.0.0.1...
Connected to localhost.localdomain (127.0.0.1).
Escape character is '^]'.
Connection closed by foreign host.
Everything else seems to be working (telnet to 110), and I turned off the firewall entirely, but I still cannot telnet to port 25. I also get a blank error within squirrelmail when attempting to send mail out (ERROR:Message not sent. Server replied: ). I apologize for not going directly to the qmailrocks forum, but they are currently closed down (due to lack of funds). I also am a newbie, so I apologize for the lack of needed information. If anyone has any ideas, please let me know what information you would need.
I have an i5 Thinkpad running Windows 7 64-bit. VT is enabled in the BIOS. I have installed vmware server v 2.0.2 but am unable to install Centos 5.5 x86_64 as a guest OS. The steps that I followed are as follows:1. Created a new VM, specifying RHEL 5 64-bit as the intended guest OS (per vmware documentation - Centos is not available as a selection2. Downloaded all 8 iso files for Centos v5.5 64-bit3. Modified the CD/DVD drive to 'connect at power' and use an iso with the path pointing to the x86_64 iso 1 of 8When I power up the VM, the console window displays 'ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin' and nothing else. The installation splash screen never appears. As a test, I downloaded the first of 7 iso files for the 32-bit version of Centos 5.5 and pointed the CD/DVD drive to that iso. In that case, the installation starts as expected. I would really like to get the 64-bit version installed and running.
View 3 Replies View RelatedWhat i want to be able to do is create a custom kickstart for my centOS 5 server. I want to create a bootable cd that I can pop in my server and basically walk away for 45 minutes and I come back and its fully installed. All the directions I have read so far tell me that I have to create a seperate ks.cfg and then I need my original centos cd to get it booted. Then the cd will ask for where the ks.cfg file is and I have to type the location. I just want to pop the CD in and type in linux_clean or something and have it perform a custom install based on the information and specification in my ks.cfg. How can I go about doing this?
View 1 Replies View RelatedI am having a problem during a fresh install of CentOS 5.3 on an IBM Intellistation Z Pro 6221. I have tested the installation media (CDs). The install runs normally until I am asked to specify the appropriate keyboard.I take the default (English) and hit next. The keyboard and mouse keys become unresponsive though the mouse pointer moves. I can go no further than this. This behavior is the same whether I install in text mode or graphic mode. I have tried the noprobe installation option without success. The box I am doing the install on dual boots fine between Windows XP and CentOS 4.7 currently.Does anyone have an idea of what the problem may be?
View 2 Replies View RelatedI am eager to install GSN3 on CentOS 5 and work on GNS3. But i am unable to find a suitable easy guide to install the same. install GSN3 on CentOS.5 with rpm links if you suggest to download.
View 1 Replies View Relatedsomebody please tell me whether it would be all right to install xp inside CentOS using VMware or it's better to do vice versa if it is ok to install xp inside centos then at the beginning when i install centos should i allocate all hard disk to this OS and later give some to xp , or initially i should keep some space for xp and install centos in the rest ?
View 1 Replies View Relatedi wanna ask if it's possible to install centos on hard2 while am running centos on hard1 then after installation is complete boot from the second hard drive. i dont have physical access to the server, all i can is connect to it through SSH. so is it possible to install centos on the second hard drive from CLI! then boot from it?
View 1 Replies View Relatedim the newbie in this area.can anyone tell me how to install centos 5.4 in this hp proliant dl160 server.what I need to do to handle this RAID thing? because it show me not detected any logical hard drive in RAID configuration utility.
View 5 Replies View RelatedIt is any possibility to install centos 5.5 on ext4 by anaconda ? Is ext4 filesystem is secure for files server (samba) ?? In anaconda installer there is only ext2, ext3 choice.
View 16 Replies View RelatedI have been trying to install clisp on one of our systems and get the error: Missing Dependency: libsigsegv.so.0()(64bit) for package: clisphowever, I have checked and the library libsigsegv-2.7-1.el5.rf.x86_64 and its associated header file package are, in fact,installed.
View 3 Replies View Relatedi have a IBM IBM BladeCenter 8677-3RU it currently doesnt have any ISO installed on the chassis since i dont know what to installed into it. The blade has 14 2 X 2.7GHZ PROCESSORS 2-socket single-core 64-bit PowerPC 970MP
4GB RAM
1 X 73.4GB SAS HARD DRIVES 1OK
based on this i can only install a ibm power [UTL]
I got a Centos 5.0 and just purchase a HP Laserjet P1102. I check Hp website and got to know that they supported linux except Centos. Anyone out there, Is there anyway to install this printer?
View 2 Replies View RelatedHow to install absolutely minimal Gnome without gnome-games, any cdrecord, dvd rw-tools, dialup modem tools, gnome-screensaver, festival etc. on Centos 5.5? If I try to remove these software separately then Gnome is gone.
View 2 Replies View Related