CentOS 5 Networking :: Can't See The Physical Network Interface With Ifconfig - A?
Jun 3, 2010
Centos el5xen x86_64 in a company network, novell-netware, Static IP I have several issues with the Xen network configuration. This configuration worked before, and was maded by a other personn with a higher level in centos and network . I'm trying to re-install xen in bridging mode.
1) The dom0 ping in the company network, but can't acess to the Internet.
I de-activated firewall, iptables and SE-Linux for the test.
the ifconfig-a command return
eth0
lo
sit0 (IPV6 encapsuled in IPV4)
vif0
vnet0
but no Peth0 Physical device
Is it normal and how can i repare this ?
View 7 Replies
ADVERTISEMENT
Jun 2, 2010
I have a strange problem regarding networking on the Alix 2d13 running Ubuntu 10.04. The Alix has 3 physical network interfaces, lspci says:
Code:
00:09.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Kernel driver in use: via-rhine
Kernel modules: via-rhine
00:0a.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Kernel driver in use: via-rhine
Kernel modules: via-rhine
[Code]...
It seems, if more than one cable is connected, a random hardware port is chosen as eth0-eth2. If only one cable is connected the port that is connected is chosen as eth0-eth2. Any idea what's going wrong here?
View 2 Replies
View Related
Jul 7, 2011
I have installed CentOS. I have two ethernet card (one onboard and one PCI). I am able to set ip for realtek ethernet card and my atheros(on board) is not shown in network ifconfig shows only one ethernet card (PCI) hen i gave the command lspci i got the following output
01:00.0 Ethernet controller: Atheros Communications AR8132 Fast Ethernet (rev c0)
03:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
View 4 Replies
View Related
Jan 24, 2010
I have a laptop running 11.2 with an internal Broadcom-based Wi-Fi card that's working fine. I'm trying to get 802.11n going with the WUSB600N. The USB ID on this device is 1737:0079. I believe this means it's a "V2" with an RT3572 chip.
No driver loads for this device when it's plugged in. If I do a "modprobe rt2870sta", a driver loads, and syslog shows "rtusb init" and "usbcore: registered new interface driver rt2870". But ifconfig -a doesn't show a new network interface. I've also tried building the RT3572 driver from the manufacturer's web site. It builds fine, and modprobe will load it, but I get the same results as the rt2870sta driver.
View 1 Replies
View Related
Sep 9, 2009
How to figure out why there are errors on bond0(eth0)
Transfer speed is in KB
View 1 Replies
View Related
Jul 18, 2011
I have a ppp0 entry with post-up options like this
mapping ppp0
map none photon-plus motorola
map timeout: 12
[code]...
View 8 Replies
View Related
Aug 22, 2010
I just installed Fedora 13 from the Live CD. FIrst off I read the guide and the first step doesn't even work for me. System>Administration>Network does not exist. If I go to System then Preferences I see a Network Manager but it looks nothing like what these screen shots look like. [url]
No wireless card show up in the wireless tab of Network Manager. How can I fix this since my card is listed in ifconfig and iwconfig. Wifi card is a Zonet zew2500p
View 2 Replies
View Related
Feb 11, 2011
I messed up my Network Connections when I put a different NIC in my computer. Now I just went back to using the old NIC. It shows up in ifconfig, but the GUI Network Connections is blank. When I manually Add the connection back to the GUI Network Connections, the settings are not reflected when doing ifconfig.For example, I change the IP address for eth0 in GUI Network Connections, save the settings,
View 6 Replies
View Related
Mar 15, 2011
I have got Ubuntu 10.10 on a Dell Inspiron Laptop. Can't get anywhere with wireless network. Tried a few bits of poking it blindly with a stick:
matthew@ubuntu:~$ lshw -C network
Warning: you should run this program as super-user.
*-network
Description: Network controller
Product: BCM4312 802.11b/g LP-PHY
Vendor: Broadcom Corporation
Physical id: 0
Bus info: pci@0000:0c:00.0
Version: 01
Width: 64 bits
Clock: 33MHz
Capabilities: bus_master cap_list
Configuration: driver=b43-pci-bridge latency=0
Resources: irq:17 memory:f69fc000-f69fffff
*-network .....
I reckon *-network DISABLED is a problem, I tried sudo ifconfig wlan0 up but that didn't work. The output of that and lspci are on the ubuntu side of my machine. I have also tried pressing my wireless on/off key (F2) but that doesn't work either.
View 8 Replies
View Related
Jul 7, 2010
i have encounter strange situation i have set all my network configuration via /etc/sysconfig/network-scripts/ifcfg-eth0 ,eth0.2 ,eth1 etc ....i have used only once Gnome network manage settings to add routing since then all my network config change although all files mention above showing the same config i have set initially and same for Gnome network Manager.
View 3 Replies
View Related
Jul 19, 2009
I get this ifconfig output for eth0:1 :
eth0:1
Where are all the packet statistics?
View 2 Replies
View Related
Jan 27, 2010
I recently installed fedora 12 in my server where I had a page published in my local net by tomcat, and I was looking on the Internet how to set up an static ip address and this is what I did
on /etc/sysconfig/network-scripts/ifcfg-eth0
# Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express
#
# File: ifcfg-eth0
[code]....
then I can access via ssh by two addresses the one I got from dhcp (10.17.148.223) and the static one (10.17.148.26) I put ifconfig and and 10.17.148.223 appear on eth0 I restart my server and I just can access from 10.17.148.223 I have to put
ifdown eth0
ifup eth0
Again...to access by my static ip, y can access my page by its dns on my server, but I cant access from other computer...so, I guess when my static adress appears on ifconfig I would be able to access my page from other computer...
View 11 Replies
View Related
Jan 28, 2011
where are the interface configurations (set by ifconfig, not the static ones) stored? I'm asking because I'm trying to understand, more broadly, the order of IP address lookup. If I ping the local machine (localhost, or one of the interfaces) no messages get sent out (at least according to wireshark), so some local lookup must be taking place.
View 1 Replies
View Related
Feb 5, 2011
I understand the software RAID partition types on two physical drives that will be paired must be set to the same size. However,
1. Do the physical drives themselves need to be the same size?
2. Do the physical drives need to use the same interface?
e.g. Can I setup mirroring with one 80G SATA, and one 320G PATA? (And is this reliable/stable?). The use is for an asterisk server which came with the 80G, I can't find anything smaller than 320G for the 2nd drive, and the free connector inside is PATA.
View 1 Replies
View Related
Jan 15, 2010
i have sun Virtual box installed on my centos as my host os and centos as guest os.The ip on Sun virtual box virtual interface is10.0.2.15 and the ip on the physical machine is 192.168.1.11.when i try to ping the ip from my vps on centos to my physical machine it pings but it does't work when i try to ping my vps ip from my physical machine.Please recommend the route enteries i need to do in physical machine
View 3 Replies
View Related
Jun 27, 2010
For some simulation, I am trying to configure a setup of 3 ubuntu desktops (one of them with multiple network cards) to behave in the following way:
Each one of them should be a separate network not seeing the others (including multicast addresses) They need to have internet access through the machine with multiple network cards. So from the point of view of each machine they define a LAN in which it is the only device and have internet access through the gateway machine.
What do I need to do to configure these machines for the above setup?
View 6 Replies
View Related
Jun 21, 2010
I am in need of finding out the physical interface corresponds to eth0,eth1,eth2., As similar like the lscfg command which is available in the AIX operating system. The output given below got it from AIX OS.
$ lscfg -l ent*
ent2 U787B.001.DNWFFC6-P1-T9 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent3 U787B.001.DNWFFC6-P1-T10 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent0 U787B.001.DNWFFC6-P1-C4-T1 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent1 U787B.001.DNWFFC6-P1-C4-T2 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
Is there any utility/commands available to find out the physical interface ?
View 1 Replies
View Related
Apr 7, 2011
I am totally new to Linux and have just installed ubuntu 10.10. After configuring the network interface via dhcp I started getting these messages that come in so frequently I can't configure anything else.
[87.186415] Stack:
Why I am getting this messages and more importantly how do I get rid of them.
The installation is on a VM on Hyper-V.
View 1 Replies
View Related
Aug 30, 2010
today I tried to configure a network route to a host for testing my network interface. Code: route add 192.168.1.15 eth0 As I have to eth interfaces and both interface got their IP from DHCP (192.168.1.11 and 192.168.1.12) and are in the same subnet, I shut the other interface down:
Code: ifconfig eth1 down Then I tried to test the interface by doing a ping to 192.168.1.15.
Problem: When I unplug the cable from eth0 (and eth1 is still plugged) the ping still works. Somehow my linux (it's debian) powers up again eth0 and pings over this port.
How can I stop my linux doing this. I just want to have the route added only on the one interface - not the other. Is it maybe some case of a default-gateway?
View 5 Replies
View Related
Jan 18, 2011
ok I am using a customized CentOS distro that is looking for 3 network cards on boot. eth0, eth1, eth2. I do not need eth0 and need to bridge it to eth1.
View 1 Replies
View Related
Jun 23, 2010
If I have only 1 physical WLAN interface, is there some hackery that can be done so that it can be a client of an existing access point and at the same time also act as an access point for other clients? I have an existing 802.11g ADSL router, and I'm going to be building an HTPC which will have 802.11n. My laptop also has 802.11n, but at the moment it only connects at 54Mbps because thats what the AP supports. I'd like to be able to have the HTPC be a client of my ADSL router, but have my laptop be a client of the HTPC, so copying files to it will be faster.
View 1 Replies
View Related
May 9, 2010
I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device.
I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up.
Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.
View 1 Replies
View Related
Mar 29, 2011
I'm having all sorts of problems connecting an access point to my computer, but here is one piece that I hope will get me going, if I can get it solved.My computer has two network interfaces, eth0 and eth1. eth1 connects to the cable modem and thence the world, and works fine. eth0 is supposed to connect to the access point over a private network. Here is the output from route with my IP address blotted out:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
[code]...
View 2 Replies
View Related
Jul 30, 2010
If I have set up 2 network interfaces on a box, if I started sending multicast traffic, it will go out through both interfaces? Or is there a way to control through which interface it will go out?
View 1 Replies
View Related
Jul 3, 2010
I have two simultaneous active mobile connections through my two mobile phones and USB data cables. Yet I can only send/receive with one connection.Each of the phone modems have a node in /dev, namely ttyACM0 and ttyACM0. So the modems are detected correctly.After setting up two dial-up connections with the two modems I have two ip's. Ifconfig-a confirms this:
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.10.219.60 P-t-P:10.6.6.6 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
[code]....
View 1 Replies
View Related
Jul 7, 2010
I would like be able to access packets coming off the network with the hopes of coding a primitive packet sniffer for learning purposes. I would also like to be able to piece together my own packets and send them out on my network. Eventually, I would also like to write a simple firewall so I want the capability to drop packets as well as let them pass. I assume I will have to access the kernel with some system calls to do this, any one have any information or resources that could help me on this project?
View 1 Replies
View Related
Jun 17, 2011
I have a webserver with 3 virtual interfaces named eth0:1 eth0:3 and eth0:3. Until yesterday all the virtual ip's worked but eth0:1 decided that it just won't work anymore since yesterday. The configs are:
eth0
Code:
DEVICE=eth0
USERCTL=no
ONBOOT=yes
BOOTPROTO=none
BROADCAST=xx.xxx.26.190
NETWORK=xx.xxx.26.160
NETMASK=255.255.255.224
IPADDR=xx.xxx.26.174
GATEWAY=xx.xxx.26.161
eth0:1
Code:
MTU=""
NETMASK=255.255.255.224
ONPARENT=yes
BROADCAST=xx.xxx.26.191
BOOTPROTO=none
NAME=""
IPADDR=xx.xxx.26.175
NETWORK=xx.xxx.26.160
ONBOOT=yes
DEVICE=eth0:1
eth0:3
Code:
MTU=""
NETMASK=255.255.255.224
ONPARENT=yes
BROADCAST=xx.xxx.26.191
BOOTPROTO=none
NAME=""
IPADDR=xx.xxx.26.182
NETWORK=xx.xxx.26.160
ONBOOT=yes
DEVICE=eth0:3
eth0:4
Code:
MTU=""
NETMASK=255.255.255.224
ONPARENT=yes
BROADCAST=xx.xxx.26.191
BOOTPROTO=none
NAME=""
IPADDR=xx.xxx.26.187
NETWORK=xx.xxx.26.160
ONBOOT=yes
DEVICE=eth0:4
route-eth0
Code:
ADDRESS0=0.0.0.0
NETMASK0=0.0.0.0
GATEWAY0=xx.xxx.26.161
eth0:3 and eth0:4 still work, but 2 doesn't
View 4 Replies
View Related
Apr 19, 2009
I have an Asterisk-server with 2 interfaces, a WAN-interface (eth1) and a LAN-interface (eth0).
SETUP :
IAX-provider(internet) --> firewall --> Asterisk-server --> switch --> clients_on_LAN
So everything coming from the IAX-provider on port 4569 is forwarded to the Asterisk-server's WAN-interface (eth1).
This needs then be routed to an internal SIP-phone (an IVR-system will define which one) via eth0.
When a call is initiated from an internal SIP-phone (they register to the IP-address assigned to eth0) it needs to be routed via eth1 to the gateway (192.168.4.250). Asterisk will setup an IAX-channel on WAN-interface (eth1) to the IAX-provider (via gateway).
So... will this work :
route add -net ip_IAXprovider netmask 255.255.255.0 gw 192.168.4.250 dev eth1
View 9 Replies
View Related
Sep 6, 2009
I'm a newbie on Linux and trying to find my feet so please be kind.I have installed vmware on my XP laptop and have installed fedora core 9. Network setting on the VMware is set to bridged. My interface eth0 which is using the wireless does not start on boot. I have to run ifup ifcfg-eth0.The file ifcfg-eth0 had onboot=yes and NM=no, so i changed it so that the NM=yes.However this does not resolve the problem at all. I have put the file back to its original configuration and I have disabled network manager and have had no luck
View 2 Replies
View Related
Jun 18, 2010
Showing my ignorance, but why would this work
address 172.16.1.8
netmask 255.255.254.0
network 172.16.1.0
broadcast 172.16.2.255
[Code]....
Notice the 2 in address. Seems to me it doesn't like the network and wants it to be 172.16.0.0, but I am adding to a network already configured this way.
View 1 Replies
View Related
