CentOS 5 Hardware :: Mounting RAID Array On Samba Server?
Jun 23, 2009
I need to mount my raid array on CentOS 5.2 samba server.
Here are my hardware specs:
Motherboard: Tyan S2510 LE dual PIII
CPU's: Intel PIII 850ghz socket 370
Memory: 4 gig Crucial 133 ECC SDRAM
OS: 2 x'x IBM Travelstar 6.4 gig 2.5 hard drives, (low heat/noise)
Storage: 4 x's Seagate 500 gig IDE 7200 rpm
RAID controller: 3Ware 7500-12 controller, (RAID 5) (66 mhz PCI bus)
NIC: 3COM 3C996B-T gigabit NIC, (66 mhz PCI bus)
I have the 2 IBM's set as RAID 1, (mirror) and the 4 Seagates as RAID 5, (1.5 TB) I have installed the OS with minor problems, (motherboard doesn't like the 2.6.18-128.1.14.el5 kernel, removed it from my grub.conf).
My problem is mounting the RAID array. I have done the following:
formatted with fdisk;
fdisk /dev/sdb
Then formatted with the following command;
mkfs.ext3 -m 0 /dev/sdb
The hard drive was formatted with the ext3 files system, but I have mounted it as an ext2 file system as I don't want 'journaling' to occur. I then edited my /ect/fstab like this: .....
Then: mount -a
When I go into my "home" directory and type ls, I get the following:
[root@hydra home]# ls -l
total 24
drwx------ 2 zog zog 4096 Jun 23 15:50 zog
lrwxrwxrwx 1 root root 6 Jun 23 15:46 home -> /home/
drwxrwxrwx 2 root root 16384 Jun 23 15:34 lost+found
drwxr-xr-x 2 root root 4096 Jun 23 17:18 tmp
Why my home directory is showing under home?
View 5 Replies
ADVERTISEMENT
May 11, 2011
Round two:I am trying to install a RAID 1 array on my system. I already have another RAID 1 array in there. I am using the BIOS RAID option to set up the array.Here's what dmraid -r tells me:
# dmraid -r
/dev/sda: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
/dev/sdb: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
[code]....
View 9 Replies
View Related
Jun 6, 2011
I have an ubuntu 10.04 machine that I use primarily as a file server. I have a RAID5 array built with mdadm from 3 component disks that worked properly until a recent upgrade (I'm not sure exactly what broke it though). The array is /dev/md0 and is set to mount at /var/media on bootup. *Now*, when the system cold boots it hangs partway through the bootup sequence and throws the following error:
The disk drive for /var/media is not ready yet Press S to skip ... Once I "S"kip this manually, I can see that LOWER in the boot sequence mdadm gets called and assembles the drive, and once fully booted into the system I can then simply do a "mount -a" and the array mounts properly. SO... my gut feeling is that some portion of one of the upgrades changed the order in which things are called, and now the "mdadm assemble" is not triggered until AFTER the system tries to mount the drives. My problem is that I don't know the stuff that controls the boot sequence well enough to dig in the right place.
As a workaround I can remove that entry from /etc/fstab, but then (of course) the system won't auto-mount the array. It's better than the boot process completely hanging because as least THIS I can fix remotely, but I'd really like to know
1) why this broke in an upgrade and is it a known problem?
2) how to get it back to where it auto-assembles and then auto-mounts the array on bootup.
View 9 Replies
View Related
Aug 1, 2011
I'm running 10.04 x86 server with a really simple installation on a single 250GB boot disk. I then have a RAID5 array as /dev/md0 (set up using mdadm with x4 2TB disks). All is working well. My mdadm.conf file looks like this
Code:
# mdadm.conf
#
# Please refer to mdadm.conf(5) for information about this file.
[code]....
if I was to lose the boot disk and need to remount the RAID array on a fresh installation, what steps do I need to go through. My assumption is that the superblocks on the RAID disks will be used and I don't need to keep any additional information - is this right?
View 6 Replies
View Related
Feb 16, 2010
I have a large RAID array of 12 TB attached to one of my Ubuntu server machines. The RAID volume is formatted with NTFS. The problem is that I can not mount this volume in Ubuntu. I can read it normally if I attach it to windows machine.This is the output from "sudo fdisk -l":
sudo fdisk -l
Disk /dev/sda: 164.7 GB, 164696555520 bytes
255 heads, 63 sectors/track, 20023 cylinders[code]........
View 2 Replies
View Related
Jul 20, 2009
I'm not able to spin down my harddisks in raid array. I did hdparm -S 240 /dev/sdb and the same for the second hdd. Smaller values like 2 minutes work. I don't have log files on this disks. How can I determine, which processes are accessing these disks? I have apache and samba running. Nobody is accessing the server.
View 2 Replies
View Related
Mar 10, 2010
I have a raid 1 array which I did setup on a Centos box. I can configure the array fine the problem is every time is restart my machine I can no longer see the array and have to go create it all over again. I tried doing a few searches on it but have came up with nothing so far.
View 19 Replies
View Related
Jul 15, 2010
I've been having troubles with software raid. In particular, the raid array becomes un "assembleable" after reboots. The config is CentOS 5, 4 sata discs (one by 160 containing OS, no raid and 3 2TB disks configured as a RAID 5 array - no spare drive). These drives were configured in anaconda and all seemed to go well (the drive and its lvm partitions worked and it finished rebuilding overnight). A couple of reboots later the drives cannot be assembled anymore and the machine won't boot. The error message says:
mdadm: /dev/md0 assembled from 1 drive and 1 spare - not enough to start the array.
Of course there are 3 drives and no spares in the array as configured. Manually starting the array with mdadm --assemble --scan gives the same message as does assembling the drive by specifying the individual parts. /proc/mdstat does recognize the 3 drives and when I look at the partition tables in fdisk, they show as being software raid. What could be wrong or steps to diagnose? I tried configuring the raid drives manually before going the anaconda route. Also, does anyone know I can edit the /etc/fstab file to disable them so the machine will at least boot. The (Repair filesystem) shell has the / drive mounted r/o.
View 7 Replies
View Related
Nov 17, 2009
Our server is a CybertronPC I2XV9080 Imperium Tower. It is equipped with a supermicro X7DVL-I Motherboard and Quad 750 GB SATA2 RAID edition hard drives in a raid 5 array. We tried to install Centos on the Raid5 array with Device-Mapper as the LVM. In the BIOS SATA Raid was enabled and the ICH RAID code base option was set to [Intel].
Intel Matrix Storage Manager Option ROM V5.6.4.1002 ESB2
RAID
ID Name Level Strip Size Status Bootable
0 Raid5 Raid 5 64KB 80GB Normal Yes
1 Raid_5 Raid 5 64kB 2000GB Normal Yes[code].....
Can I have multiple level raids across the same array or would that lead to problems as above? Is the root cause of my problem the fact that intel raid5 is not supported for Linux as based on the following link http:[url]....
View 3 Replies
View Related
Sep 23, 2011
I have a home samba server with a 3ware Escalade 8506-8. I have 5 x 500 gig hard drives in a RAID 5 array. Recently, my 8506 died and I need to get a new one. However, I saw a 3ware Escalade 9500S-12 on ebay for about $20.00 dollars more than a replacement 8506-8.
My question is, if I put my drives on the 9500S, will it recognize my existing RAID array? Or will it want to build a new RAID array and format all of my data?Hope I have asked this question clearly, little short on sleep this week.
View 3 Replies
View Related
Mar 25, 2010
I have a 10x2tb disk array that i'm trying to build into a single software raid 5 i have tried this 2 times now the first it made it to 58.7% and the machine locked up and the array would not restart after a reboot. On my 2nd try all was looking good until about 50% i noticed that the speed dropped in 1/2 and that ksoftirqd/2 is taking up a lot of cpu (about 90%) the md0_resync and md0_raid5 are also taking 60-90% when the build started they took 7%. when i do a dmesg i see a lot of the message compute_blocknr: map not correct.
For a little info on the physical setup this is running on an Atom 510 with 2GB of mem the drives are connected to an addonics 4-Port RAID 5 / JBOD SATA II PCI Controller using the sil3124 chipset. I'm using 2 addonics 5X1 SATA Port Multiplier connected to the controller to get the 10 drives attached. All drive show up and don't seem to have any issues. I'm running a fully updated as of 3/20/10 version of centos 5.4
I will let this continue to run over night but i expect it to be locked up by morning if it follows what the last attempt did.
View 9 Replies
View Related
Dec 10, 2010
I have acquired a dell 2850 poweredge server and installed ubuntu server onto only to find out we cant use linux for its intended use and need to uninstall remove ubuntu and it has a raid 5 array on the server.
View 1 Replies
View Related
Jan 27, 2010
I had a raid 5 + lvm 2 array and lost a disk. While it was recovering the array, the power was down and recovery stopped. When I recovered the power and start the machine the array was unable to start, it was degraded and the states were different between disks. Every disk watched the array in a different way. I put you the states:
Quote:
/dev/sdd1
Number Major Minor RaidDevice State
this 0 8 33 0 active sync /dev/sdc1
[code]....
The first part in /dev/sdc1 is the same for all the devices, I just post you the states. Another thing is tha all the devices say that there is no superblock It seems that 3 disks are "active sync" but the states of the others doesn't match between them. And /dev/sdd1 is spare, the disk I added manually at first to start the recovery process.
View 3 Replies
View Related
Apr 8, 2010
Is there a way for me to mount a raid array member directly without using any of the raid tools? For instance, I have a raid 1 array that contains /dev/sda1 and /dev/sdb1. How can I mount /dev/sda1 or /dev/sdb1 directly? Doing mount /dev/sda1 <mnt point> does not work. If I try specifying the filesystem type with -t this doesn't work either.
View 1 Replies
View Related
Dec 21, 2010
I have been having some odd issues over the last day or so while trying to get a raid 5 array running in software under Kubuntu. I installed 3 1TB drives and started up, my sd* order got all messed up( sda was now sdc and so on). This wasn't entirely unexpected, so I fixed up fstab and booted again. I found all three of the drives I installed, set them to raid auto-detect and used mdadm to create /dev/md0. I then created mdadm.conf by piping the output of mdadm --detail --scan --verbose into /etc/mdadm.conf.At this point, everything was still going swimmingly. I copied over a few hundred GB of data from another failing drive and everything seemed ok. I went to reboot once the copy was done and everything just went weird. All of the sd* drives went back to the original. Of course, this meant that the mdadm.conf was wrong. I tried to just change the device list, but that didn't work. I then deleted mdadm.conf and rebooted. The drive list stayed in the original order this time, so I just tried manually starting the array.
By erasing the partition table of the 3rd drive, I've been able to get it to the status of spare, but it says it is busy when I try to add it to the array. A grep through dmesg makes me think that md has a lock on it. I'm not sure where to go with it now. If anyone has any pointers, I would like to hear them.
Device List(original):
/dev/sda => boot drive, /home /
/dev/sdb => 1.5TB media storage, failing
[code]...
View 1 Replies
View Related
Nov 16, 2009
mdadm --create /dev/md1 --level=1 --raid-disks=2 missing /dev/sdb1and I getmd1: raid array is not clean -- starting background reconstructionWhy is it not clean?Should I be worried?The HD is not new it has been used in before in a raid array but has beenrepartitionated.
View 2 Replies
View Related
Jun 7, 2011
I have 4 WD10EARS drives running in a RAID 5 array using MDADM.Yesterday my OS Drive failed. I have replaced this and installed a fresh copy of Ubuntu 11.04 on it. then installed MDADM, and rebooted the machine, hoping that it would automatically rebuild the array.It hasnt, when i look at the array using Disk Utility, it says that the array is not running. If i try to start the array it says :Error assembling array: mdadm exited with exit code 1: mdadm: failed to RUN_ARRAY /dev/md0: Input/output error
mdadm: Not enough devices to start the array.I have tried MDADM --assemble --scan and it gives this output:mdadm: /dev/md0 assembled from 2 drives - not enough to start the array.I know that there are 4 drives present as they are all showing, but it is only using 2 of them.I also ran MDADM -- detail /dev.md0 which gave:
root@warren-P5K-E:~# mdadm --detail /dev/md0
/dev/md0:
Version : 0.90
[code]...
View 11 Replies
View Related
Mar 25, 2011
I have been running a server with an increasingly large md array and always been plagued with intermittent disk faults. For a long time, I've attributed those to either temperature or power glitches. I had just embarked on a quest to a) lower case and drive temperature. They were running between 43 and 47C, sometimes peaking at 52C, so I've added more case fan power and made sure the drive cage was in the flow (it has it's own fan, too). Also, I've upgraded my power supply and made very sure that all the connectors are good. The array currently is a RAID6 with 5 Seagate 1,5TB drives.
When everything seemed to be working fine, I looked at my SMART logs and found that two of my drives (both well over 14000 operating hours) were showing uncorrectible bad blocks. Since it's RAID6, I figured, I couldn't do much harm, ran a badblocks test on it, zeroed the blocks that were reported bad, figuring the drive defect management would remap them to a good part of the disk and zeroed the superblock. I then added it back to the pack and the resync started. At around 50%, a second drive decided to go and shortly thereafter a third. Now, with two out of five drives, RAID6 will fail. Fine. At least, no data will be written to it anymore, however, now I cannot reassemble the array anymore.
Whenever I try I get this:
Code:
mdadm --assemble --scan
mdadm: /dev/md1 assembled from 2 drives and 2 spares - not enough to start the array
Code:
cat /proc/mdstat
Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [linear]
md1 : inactive sdf1[4](S) sde1[6](S) sdg1[1](S) sdh1[5](S) sdd1[2](S)
7325679320 blocks super 1.0
md0 : active raid1 sdb2[0] sdc2[1]
312464128 blocks [2/2] [UU]
bitmap: 3/149 pages [12KB], 1024KB chunk
Which is not fine. I'm sure that three devices are fine (normally, a failed device would just rejoin the array, skipping most of the resync by way of the bitmap) so I should be able to reassemble the array with the two good ones and the one that failed last, then add the one that failed during the resync and finally re-add the original offender. However, I have no idea how to get them out of the "(S)" state.
Code:
mdadm --examine /dev/sdd1
/dev/sdd1:
Magic : a92b4efc
Version : 1.0
Feature Map : 0x1
Array UUID : d79d81cc:fff69625:5fb4ab4c:46d45217 .....
View 2 Replies
View Related
Feb 3, 2011
When we assemble a raid array, from where does it load configuration information for that array? I thought it refers to /etc/mdadm.conf file, but in my system, mdadm.conf file doesn't even contain all information. Still it is able to successfully assemble previously created device.
# cat /etc/mdadm.conf
DEVICE /dev/sd[bcdjkl]1
DEVICE /dev/loop[012345]
[code]...
View 2 Replies
View Related
Dec 11, 2010
I rebuilt a server and am now trying to recover my large data arrays. The server was ubuntu 10.04lts before. I decided to rebuild it with CentOS simply because I am more familiar with it. I had 2 raid-5 arrays on the old server:4 x 1tb -> md0 5 x 2tb -> md1 The newly built server does not know about these arrays yet. How can I reassemble the arrays without loosing my data? I know the data can still be accessed because booting the server with a live-cd mounts and shows the arrays just fine. Should I boot with a live cd and copy the mdadm config file?
View 5 Replies
View Related
Sep 27, 2010
I have a NETGEAR ReadyNAS NV+ with four 1TB drives in a RAID-5 array. This is our primary file storage. This has previously been backed up to a hardware RAID-0 array directly attached to our Windows server. The capacity of this backup array is no longer sufficient. So the plan was, take a bunch of 200GB to 320GB drives (And a 750) I had kicking around, chuck them in a couple of old SCSI drive enclosures I have collecting dust, attach them via IDA/SATA-to-USB adaptors to a USB hub, attach that to the server, create a JBOD array spanning the disks, and back up the NAS to that. Performance is not an issue as this is just to be used for backup, with the idea being as near to zero cost as possible (Spend so far = NZ$100�ish).
The first hurdle I struck was Windows not supporting Dynamic Disks on USB drives (Required to create a spanned volume). At first I resisted using another machine (i.e. a machine running Ubuntu) as I didn't want to dedicate a piece of hardware to backing up the NAS. I then decided it would be acceptable to do this via a VM, which is what I've done.So I have 10.04 running under VMWare Server 2.0.2 under Windows Server 2008 R2. The disks are all presented to the VM. I wasn't sure if I was going to end up creating the array under LVM or something else, but I noticed Disk Utility has an option to create an array, so I tried that. When I add two 250GB drives, the array size is 500GB. When I then add a 160GB drive, the array size drops to 480GB. Huh? If I keep adding disks (Regardless of order) the final array size comes out at 1.8 TB, as per the attached screenshot. Now with the following drives, I expected something more like:
160 + 250 + 250+ 750 + 250 +200 + 200 + 250 + 320 + 250 + 320 = 3.2TB
Am I missing something or making a false assumption somewhere?
View 4 Replies
View Related
Jun 7, 2011
I recently upgraded a server from Fedora 6 to Fedora 14. In addition to the main hard drive where the OS is installed, I have 3 1TB hard drives configured for RAID5 (via software). After the upgrade, I noticed one of the hard drives had been removed from the raid array. I tried to add it back with mdadm --add, but it just put it in as a spare. I figured I'd get back to it later.Then, when performing a reboot, the system could not mount the raid array at all. I removed it from the fstab so I could boot the system, and now I'm trying to get the raid array back up.
I ran the following:mdadm --create /dev/md0 --assume-clean --level=5 --chunk=64 --raid-devices=3 missing /dev/sdc1 /dev/sdd1I know my chunk size is 64k, and "missing" is for the drive that got kicked out of the array (/dev/sdb1).That seemed to work, and mdadm reports that the array is running "clean, degraded" with the missing drive.However, I can't mount the raid array. When I try:mount -t ext3 /dev/md0 /mnt/fooI get:
mount: wrong fs type, bad option, bad superblock on /dev/md0,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
[code]....
View 1 Replies
View Related
Oct 27, 2010
We have some servers that run in very harsh environments (research vessel) that need to have high-availability.We have software RAID 1 for some measure of resiliency, along with proper data backups (tapes etc), however we would like to be able to break out a new server and re-image it (including RAID setup) from a known good copy if the hardware completely fails on the production box. Simplicity of the process is a big plus.I am interested in any advice on the best way to approach this. My current approach (relatively new to Linux administration, totally new to MDADM) is to use DD to take a complete gzipped copy of one of the RAID'ed devices (from a live CD): ode:
dd if=/dev/sda bs=4096 | gzip -c > /mnt/external/image/test.img then reverse the process on the new PC, finally using Code:mdadm --assemble to re-create and re-build the array.
View 1 Replies
View Related
Nov 30, 2010
I am learning software raid 1 with centos 5.5. I created the raid with out any problems and removed the first drive to check there was no problems and it booted. I have installed the old drive back in the system as hdc and need to resync the drives (used old drive as partitions correct) I thought I could use raidhotadd but id does not seem to exist anymore. how I resync the drives in the array hda primary and hdc secondary using mdadm
View 1 Replies
View Related
Feb 20, 2011
This is message I get when I try and start itmdadm: /dev/md0 assembled from 2 drives - not enough to start the arrayBelow is the information I've collected about any help on how I can get the raid back up and going to I can get the data off of it would be awesome
sudo mdadm --examine --scan -v
ARRAY /dev/md0 level=raid10 num-devices=4 UUID=91c36708:a7cbb532:5b51dc92:ba008491
devices=/dev/sdd1,/dev/sdc1,/dev/sdb1,/dev/sda1
[code]...
View 1 Replies
View Related
Aug 4, 2010
Trying to install RHEL5-AS 64bit onto HP DL320 G6, with RAID being a mirrored array on the Smart Array B110i SATA controller. The RAID is configured in the BIOS and seems fine.
When I install RedHat, I have to use 'linux dd' to use the HP provided driver (http://h20000.www2.hp.com/bizsupport...5&mode=4&idx=0) and that works fine during the installer, the GUI during the install sees the RAID just fine, it sees one volume, calling it the HP Volume. However, when the system boots after the install, the RAID is gone, and it's now seeing two drives, /sda and /sdb:
[Code]...
View 2 Replies
View Related
Jul 22, 2009
I've to make a Windows 2000 share on my Server Linux CentOS 5.1 with all the updates installed with yum. I've a directory on a Windows 2000 that contains some images for a catalogue. I have my internet site on CentOS 5.1 with a Apache - Mysql - PHP web server. I have to mount my directory on a share in /mnt/catalogueimages and made a symbolic link from my /var/www/html/mysite/catimages to this samba share.
This is what I do following your guide a this link: [URL]
I have placed in my /etc/fstab this line:
//SERVER/C/Catalogue /mnt/catalogueimages cifs user,username=Administrator,password=,uid=apache,gid=apache 0 0
My Windows 2000 server have no password.
After that I made the symbolic link:
ln -s /mnt/catalogueimages /var/www/html/mysite/catimages
All it's OK.
The problem is that I can't see the images via browser. I have tried also to put some images in the directory /mnt/catalogueimages, deleting the mount point, in order to see if the problem was in apache: the images are visible via browser. Why I don't reach to see the images mounted with samba?
View 9 Replies
View Related
Apr 28, 2009
I've just setup a new centos 5.3 server with a 3-disc raid 5 software RAID array. I've setup other software raid 5 arrays on this same hardware, whilst testing, and had no trouble... I only just installed 3 new drives and performed a new install from scratch.
Hardware is: 4800XP X2 64-bit, 2GB RAM, Albatron KI-690G mainboard with Marvel SATA controller (I think) - 4 ports.
SATA port 0 is system drive (OCZ vertex 32GB SSD)
SATA port 1 is Western Digital "green" 1TB 8MB cache SATA 2
SATA port 2 is Western Digital "green" 1TB 8MB cache SATA 2
SATA port 3 is Western Digital "green" 1TB 8MB cache SATA 2
Ports 1-3 in software raid MD0 (raid 5)
All of this was configured in the GUI setup, with LVM on top of software RAID 5 mounted on /var. Partition size is ~1.9TB
Trouble is I get all sorts of "hardware failure" messages at bootup and the MD driver reports it was only able to bring up 2 out of 3 drives in the RAID set... however the RAID set formatted fine during the setup?
Here is the relevent dmesg output...
View 2 Replies
View Related
Aug 3, 2010
I am trying to connect a RAID Box to the server via LSI 8880EM2 RAID controller.The raid box is FUjitsu Externus DX60 with raid 1 configured.The server is Fujitsu Primergy SX300 S5 with LSI 8880EM2 RAID card.The external raid box is being recognised by the raid controllers bios.
The server runs CentOS 5.5 64bit. I have installed the megaraid_sas driver from LSI website and MegaCLI utility but CentOS still fails to see the box.MegaCLI utility, when launched from CentOS, recognises the raid box, CentOS does not(no mapping being created in /dev).
I have also tried to create a logical RAID0 HDD on one physical HDD(as seen by MegaCLI) with MegaCLI utility in CentOS.The result was success and the new logical drive could have been used, but when restarting the server, the controllers' bios fails with an error (not surprised(one logical RAID0 on one physical HDD)) and configuration is being erased.
Has anyone tried connecting 8880EM2 controller to a raid box with raid configured on the box, running it all under CentOS and what were the results.
View 3 Replies
View Related
Dec 15, 2010
So I didn't notice when I setup my CentOS 5.5 server that I left / as RAID 0 on md1. All the rest are RAID 1. Is there a way I can modify the array to RAID 1 without a risk of data loss? I'm glad I caught this before I setup any other services. I've only setup smb so far...
[root@ftpserver ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/md1 16G 3.0G 13G 20% /
[code]....
View 1 Replies
View Related
