CentOS 5 Hardware :: 20 TB Software Raid 5 Build - Locked Up And Array Would Not Restart After Reboot
Mar 25, 2010
I have a 10x2tb disk array that i'm trying to build into a single software raid 5 i have tried this 2 times now the first it made it to 58.7% and the machine locked up and the array would not restart after a reboot. On my 2nd try all was looking good until about 50% i noticed that the speed dropped in 1/2 and that ksoftirqd/2 is taking up a lot of cpu (about 90%) the md0_resync and md0_raid5 are also taking 60-90% when the build started they took 7%. when i do a dmesg i see a lot of the message compute_blocknr: map not correct.
For a little info on the physical setup this is running on an Atom 510 with 2GB of mem the drives are connected to an addonics 4-Port RAID 5 / JBOD SATA II PCI Controller using the sil3124 chipset. I'm using 2 addonics 5X1 SATA Port Multiplier connected to the controller to get the 10 drives attached. All drive show up and don't seem to have any issues. I'm running a fully updated as of 3/20/10 version of centos 5.4
I will let this continue to run over night but i expect it to be locked up by morning if it follows what the last attempt did.
View 9 Replies
ADVERTISEMENT
Mar 10, 2010
I have a raid 1 array which I did setup on a Centos box. I can configure the array fine the problem is every time is restart my machine I can no longer see the array and have to go create it all over again. I tried doing a few searches on it but have came up with nothing so far.
View 19 Replies
View Related
Apr 24, 2011
I had some issues with my RAID6 array (with 15 disks), where 5 disks got disconnected (each five disks is connected to the motherboard via 1 SATA cable), which brought down the RAID array. I fixed this problem via readding the disks and running the array:
Code:
mdadm -R /dev/md1
However, after rebooting, the array appears inactive, and I have to go through the same motions to fix this and make it active.
The array is present in the /etc/mdadm/mdadm.conf, though also 2 other raid arrays (3 arrays total):
Code:
DEVICE partitions
# auto-create devices with Debian standard permissions
CREATE owner=root group=disk mode=0660 auto=yes
[code]...
View 1 Replies
View Related
Jan 6, 2011
1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays:
2x320GB RAID1 - used for operating systems md126
2x1TB RAID1 - used for data md125
I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only":
[Code]...
and the partition in it was not available as device special file in /dev:
[Code]...
View 1 Replies
View Related
May 11, 2011
Round two:I am trying to install a RAID 1 array on my system. I already have another RAID 1 array in there. I am using the BIOS RAID option to set up the array.Here's what dmraid -r tells me:
# dmraid -r
/dev/sda: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
/dev/sdb: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
[code]....
View 9 Replies
View Related
Jul 20, 2009
I'm not able to spin down my harddisks in raid array. I did hdparm -S 240 /dev/sdb and the same for the second hdd. Smaller values like 2 minutes work. I don't have log files on this disks. How can I determine, which processes are accessing these disks? I have apache and samba running. Nobody is accessing the server.
View 2 Replies
View Related
Jul 15, 2010
I've been having troubles with software raid. In particular, the raid array becomes un "assembleable" after reboots. The config is CentOS 5, 4 sata discs (one by 160 containing OS, no raid and 3 2TB disks configured as a RAID 5 array - no spare drive). These drives were configured in anaconda and all seemed to go well (the drive and its lvm partitions worked and it finished rebuilding overnight). A couple of reboots later the drives cannot be assembled anymore and the machine won't boot. The error message says:
mdadm: /dev/md0 assembled from 1 drive and 1 spare - not enough to start the array.
Of course there are 3 drives and no spares in the array as configured. Manually starting the array with mdadm --assemble --scan gives the same message as does assembling the drive by specifying the individual parts. /proc/mdstat does recognize the 3 drives and when I look at the partition tables in fdisk, they show as being software raid. What could be wrong or steps to diagnose? I tried configuring the raid drives manually before going the anaconda route. Also, does anyone know I can edit the /etc/fstab file to disable them so the machine will at least boot. The (Repair filesystem) shell has the / drive mounted r/o.
View 7 Replies
View Related
Jun 23, 2009
I need to mount my raid array on CentOS 5.2 samba server.
Here are my hardware specs:
Motherboard: Tyan S2510 LE dual PIII
CPU's: Intel PIII 850ghz socket 370
Memory: 4 gig Crucial 133 ECC SDRAM
OS: 2 x'x IBM Travelstar 6.4 gig 2.5 hard drives, (low heat/noise)
Storage: 4 x's Seagate 500 gig IDE 7200 rpm
RAID controller: 3Ware 7500-12 controller, (RAID 5) (66 mhz PCI bus)
NIC: 3COM 3C996B-T gigabit NIC, (66 mhz PCI bus)
I have the 2 IBM's set as RAID 1, (mirror) and the 4 Seagates as RAID 5, (1.5 TB) I have installed the OS with minor problems, (motherboard doesn't like the 2.6.18-128.1.14.el5 kernel, removed it from my grub.conf).
My problem is mounting the RAID array. I have done the following:
formatted with fdisk;
fdisk /dev/sdb
Then formatted with the following command;
mkfs.ext3 -m 0 /dev/sdb
The hard drive was formatted with the ext3 files system, but I have mounted it as an ext2 file system as I don't want 'journaling' to occur. I then edited my /ect/fstab like this: .....
Then: mount -a
When I go into my "home" directory and type ls, I get the following:
[root@hydra home]# ls -l
total 24
drwx------ 2 zog zog 4096 Jun 23 15:50 zog
lrwxrwxrwx 1 root root 6 Jun 23 15:46 home -> /home/
drwxrwxrwx 2 root root 16384 Jun 23 15:34 lost+found
drwxr-xr-x 2 root root 4096 Jun 23 17:18 tmp
Why my home directory is showing under home?
View 5 Replies
View Related
Nov 17, 2009
Our server is a CybertronPC I2XV9080 Imperium Tower. It is equipped with a supermicro X7DVL-I Motherboard and Quad 750 GB SATA2 RAID edition hard drives in a raid 5 array. We tried to install Centos on the Raid5 array with Device-Mapper as the LVM. In the BIOS SATA Raid was enabled and the ICH RAID code base option was set to [Intel].
Intel Matrix Storage Manager Option ROM V5.6.4.1002 ESB2
RAID
ID Name Level Strip Size Status Bootable
0 Raid5 Raid 5 64KB 80GB Normal Yes
1 Raid_5 Raid 5 64kB 2000GB Normal Yes[code].....
Can I have multiple level raids across the same array or would that lead to problems as above? Is the root cause of my problem the fact that intel raid5 is not supported for Linux as based on the following link http:[url]....
View 3 Replies
View Related
Sep 23, 2011
I have a home samba server with a 3ware Escalade 8506-8. I have 5 x 500 gig hard drives in a RAID 5 array. Recently, my 8506 died and I need to get a new one. However, I saw a 3ware Escalade 9500S-12 on ebay for about $20.00 dollars more than a replacement 8506-8.
My question is, if I put my drives on the 9500S, will it recognize my existing RAID array? Or will it want to build a new RAID array and format all of my data?Hope I have asked this question clearly, little short on sleep this week.
View 3 Replies
View Related
Jun 22, 2010
I installed CentOS 5.5. After install, I decided to put 3 identical disk for raid 5. All the disks are IDE disk. Then I put a sata disk and partitioned it to add another partition to the raid 5 array. Everything works fine until I rebooted my system. After reboot, the sata partition I added into raid 5 is showing removed. I had to readd it using "mdadm --add" to make raid 5 array works.
View 5 Replies
View Related
Sep 27, 2010
I have a NETGEAR ReadyNAS NV+ with four 1TB drives in a RAID-5 array. This is our primary file storage. This has previously been backed up to a hardware RAID-0 array directly attached to our Windows server. The capacity of this backup array is no longer sufficient. So the plan was, take a bunch of 200GB to 320GB drives (And a 750) I had kicking around, chuck them in a couple of old SCSI drive enclosures I have collecting dust, attach them via IDA/SATA-to-USB adaptors to a USB hub, attach that to the server, create a JBOD array spanning the disks, and back up the NAS to that. Performance is not an issue as this is just to be used for backup, with the idea being as near to zero cost as possible (Spend so far = NZ$100�ish).
The first hurdle I struck was Windows not supporting Dynamic Disks on USB drives (Required to create a spanned volume). At first I resisted using another machine (i.e. a machine running Ubuntu) as I didn't want to dedicate a piece of hardware to backing up the NAS. I then decided it would be acceptable to do this via a VM, which is what I've done.So I have 10.04 running under VMWare Server 2.0.2 under Windows Server 2008 R2. The disks are all presented to the VM. I wasn't sure if I was going to end up creating the array under LVM or something else, but I noticed Disk Utility has an option to create an array, so I tried that. When I add two 250GB drives, the array size is 500GB. When I then add a 160GB drive, the array size drops to 480GB. Huh? If I keep adding disks (Regardless of order) the final array size comes out at 1.8 TB, as per the attached screenshot. Now with the following drives, I expected something more like:
160 + 250 + 250+ 750 + 250 +200 + 200 + 250 + 320 + 250 + 320 = 3.2TB
Am I missing something or making a false assumption somewhere?
View 4 Replies
View Related
Apr 28, 2009
I've just setup a new centos 5.3 server with a 3-disc raid 5 software RAID array. I've setup other software raid 5 arrays on this same hardware, whilst testing, and had no trouble... I only just installed 3 new drives and performed a new install from scratch.
Hardware is: 4800XP X2 64-bit, 2GB RAM, Albatron KI-690G mainboard with Marvel SATA controller (I think) - 4 ports.
SATA port 0 is system drive (OCZ vertex 32GB SSD)
SATA port 1 is Western Digital "green" 1TB 8MB cache SATA 2
SATA port 2 is Western Digital "green" 1TB 8MB cache SATA 2
SATA port 3 is Western Digital "green" 1TB 8MB cache SATA 2
Ports 1-3 in software raid MD0 (raid 5)
All of this was configured in the GUI setup, with LVM on top of software RAID 5 mounted on /var. Partition size is ~1.9TB
Trouble is I get all sorts of "hardware failure" messages at bootup and the MD driver reports it was only able to bring up 2 out of 3 drives in the RAID set... however the RAID set formatted fine during the setup?
Here is the relevent dmesg output...
View 2 Replies
View Related
Dec 15, 2010
So I didn't notice when I setup my CentOS 5.5 server that I left / as RAID 0 on md1. All the rest are RAID 1. Is there a way I can modify the array to RAID 1 without a risk of data loss? I'm glad I caught this before I setup any other services. I've only setup smb so far...
[root@ftpserver ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/md1 16G 3.0G 13G 20% /
[code]....
View 1 Replies
View Related
Jul 5, 2011
Something happened where my RHEL6 computer locked up and I needed to shutdown the computer manually via holding the power button. When I turn the computer back on all I see is the wallpaper and mouse cursor...no log in window or anything. I can do the alt-shift F1/f2 thing where I can log in via terminal type commands but I cant get the normal display to work. When going init 5 in the console x loads but still nothing but the wallpaper and mouse. When I go back to console it seems to be stuck at enabling bluetooth devices...but I dont believe I even have a bluetooth device.
View 9 Replies
View Related
Jun 24, 2009
I've tried to install Fedora 11, both 32 and 64 on my main machine.It could not install as it stops on the first install window. I've already filed a bug but really haven't seen any feed back yet.The bug has something to do with Anaconda and the Raid array but I really can't tell.
I have an Intel Board (see signature). I am running intel raid software under W7 currently.It works fine. But, I'm wondering, when I attempt to install F!!, is my current raid set-up causing problems? Do I need to get rid of the intel raid software and use a Fedor/Linux raid program to manage the raid array??
View 2 Replies
View Related
Oct 16, 2010
I've been running Ubuntu Maverick as a fresh install since release, and for the last 2 days, I'm having to log in twice! This is only on a locked screen, not on reboot or switch users. After the first login, I see the desktop for a second, then the screen goes blank. I wiggle the mouse and the login screen is there again. The 2nd login goes as normal.
I have gradually been installing things as I need them over the week since install, but I can't pin it down to any of those. It's getting pretty annoying when the screen saver kicks in!
View 3 Replies
View Related
Jul 8, 2011
I have software raid 5 array, each time I reboot my server, I have to rebuild array again. Rebuilding array takes too long. I am using ubuntu server 10.10.
View 7 Replies
View Related
Oct 19, 2010
Consider the following setup: Ubuntu system installed on a separate SSD for speed. An ubuntu software RAID array consisting of X number of physical HDD's for storage (RAID6 or RAID10). RAID setup is done during system install. If I suffer a total crash of the SSD and loose my system, will I be able to, using a new system disk, "reconnect" to the RAID array even if the "mothersystem" of the software RAID is lost? If yes, are there any particular config- or system files I need to backup to be able to rescue the array or will it just be recognized "out-of-the-box" when reinstalling ubuntu?
View 4 Replies
View Related
Aug 28, 2010
I am using Ubuntu 10.04 x64. I am not trying to install Ubuntu on a RAID 1 drive like all of the guides are for. I have a RAID 1 array that I am using for data storage. In windows it shows as a single array just fine. In linux it shows as 2 separate drives. I don't care how they show up to be honest I just have to data written to one drive written to the other automatically as well so my RAID isn't screwed up. Looking through different articles and forums I find a lot of stuff saying that it should show up under /dev/mapper/dxxx or something under /dev/mapper. All that shows up there for me is a device called control which doesn't seem to do something.
View 1 Replies
View Related
Nov 4, 2010
I just installed Ubuntu 10.10 64bit and wanted to get access to my nvidia RAID array. This array is working, and is NTFS formatted. But wasn't showing up through normal means in Ubuntu. (for example the NTFS Configuration Tool didn't display it) Here's what the system showed.
Code:
root@hermes:~# ls -l /dev/mapper/
total 0
crw------- 1 root root 10, 59 2010-11-03 22:39 control
lrwxrwxrwx 1 root root 7 2010-11-03 22:42 nvidia_dadijiag -> ../dm-0
[code]....
Is my mirror still in effect, or did i just mount one of the specific drives from the mirror?
View 1 Replies
View Related
Jan 24, 2011
I'm going a little bit crazy. I can't seem to remove my RAID 1 arrays. Any suggestions? I don't need to save data. The drives are empty. I'm upgrading to 4 2TB drives.Running Lucid Lynx server
Code:
jessica@nas:~$ cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10]
md2 : active raid1 sdb1[1]
976759936 blocks [2/1] [_U]
md0 : active raid1 sdd1[0]
[Code]...
View 5 Replies
View Related
Feb 3, 2011
i am trying to increase raid1 arraysize whcih is predefind,what i did i add two more drive in the raid but i could not increase raid array
exp:-
Creation Time : Wed Feb 2 18:14:56 2011
Raid Level : raid1
[code]....
View 1 Replies
View Related
Sep 8, 2010
I did a search and couldn't find anything pertaining to this - if I've missed something please direct me in the right direction We have an Ubuntu box set up as a headless office server (latest desktop install of Ubuntu) and we recently set up two 1TB HDDs in a RAID1 array using mdadm - as far as I can tell it worked successfully and created /dev/md0 with an ext3 file system. After sharing the drive I can see it from the other office computers and could transfer data to and from the RAID array just fine.
I didn't figure out how to get it to automatically mount on boot so I restarted it to see if it would do so by default - however, when I restarted I couldn't see the RAID array any longer on the desktop and it came up as a 0.0kb RAID array in Disk Utility, saying it was broken. It wouldn't let me check it until I stopped and restarted the array.
After restarting I hit "check array" and it appears to be repairing the drives. What have I missed? What happened here? How can I fix it? What other info can I provide to assist:
sudo blkid shows:
/dev/sda1: UUID: "<snip>" TYPE="ext3" (system HDD)
/dev/sda5: UUID: "<snip>" TYPE="swap"
/dev/sdc1: UUID: "<snip>" TYPE="linux_raid_member"
/dev/sdb1: UUID: "<snip>" TYPE="linux_raid_member"
/dev/md0: UUID: "<snip>" SEC_TYPE="ext2" TYPE="ext3"
disk utility: RAID Array: Mirror (RAID-1), Metadata version 0.90.0, Partitioning: Not Partitioned, Components: 2...
View 1 Replies
View Related
Dec 22, 2010
I installed Debian 5.0.3 (Backport with .34 Kernel), because my server hardware (Dell PowerEdge R210) needs special firmware and drivers.However, the installation went quite smooth.I put the system on a RAID 1 Array with about 500 GB space.s I said the installation went well, however, it doesn't boot! No GRUB, nothing
View 4 Replies
View Related
Aug 29, 2015
Just setup with Debian 8 (LXDE) a few weeks ago. Raid10 array was preexisting.
Was working well. After booting I would need to go to the save as then would need to enter the root password and everything would be good.
Can't access the array.
Used to use the command $ mount /dev/dm-o /home/myspace/folder under Debian 7.6 to mount the array (no longer works).
blkd lists a /dev/md0 but instead of UUID it is PTUUID
[Code] .....
View 0 Replies
View Related
Oct 30, 2010
I installed RC1, and never touched the disks that were raided previously, and the attached image is what i see for my raid array that was previously working fine.
View 3 Replies
View Related
Mar 17, 2010
I want to make a RAID5 array with 4 2TB hard drives. One of the drives is full of data so I will need to start with a 3 disks and then once I copy the data from the 4th onto the array, I will then add the 4th drive. This will be my first experience with RAID. I've spent a few hours searching for info but most of what I have found is a bit over my head.
View 9 Replies
View Related
Jun 29, 2010
I'm just about to be given a Power Mac G5 (Late 2005) Dual 2.0GHz. I think this was the last G5 produced.I plan on using it as file server/NAS and will probably run 10.04 LTS (or maybe 8.04 LTS). I would install a SATA RAID controller and run 4 1TB drives in a RAID 5 configuration. The only thing I'm unsure about is choosing a compatible RAID controller. I need to find a RAID controller that
- Is PCIe
- Is compatible with both the Power Mac and Ubuntu PPC
- Does true hardware RAID
- Doesn't cost a fortune!
Am I right in thinking that the card might need to be open firmware compatible? If it makes any difference, I plan on running the OS from a separate 5th drive. I've found this on eBay. I asked the seller and he claims it supports true hardware RAID and says the chipset is a Silicon Image SIL3124. I does seem suspiciously cheap though...
View 2 Replies
View Related
Jul 11, 2010
After upgrading my ubuntu install my raid array is gone. The drives appear in blkid as "Linux raid member" and both have the same uuid. If I try to mount the drive via fstab I get a message that the drive is not ready or present. If I try to mount each of the two drives, one mounts successfully the other reports serious errors. Issuing a cat /proc/mdstat shows md_d0 as inactive.How can I re-establish my raid array? I have the data backed up so if I have to wipe out the disks to start over that's an option.
View 2 Replies
View Related
