i am trying to increase raid1 arraysize whcih is predefind,what i did i add two more drive in the raid but i could not increase raid array
exp:-
Creation Time : Wed Feb 2 18:14:56 2011
Raid Level : raid1
[code]....
I have a NETGEAR ReadyNAS NV+ with four 1TB drives in a RAID-5 array. This is our primary file storage. This has previously been backed up to a hardware RAID-0 array directly attached to our Windows server. The capacity of this backup array is no longer sufficient. So the plan was, take a bunch of 200GB to 320GB drives (And a 750) I had kicking around, chuck them in a couple of old SCSI drive enclosures I have collecting dust, attach them via IDA/SATA-to-USB adaptors to a USB hub, attach that to the server, create a JBOD array spanning the disks, and back up the NAS to that. Performance is not an issue as this is just to be used for backup, with the idea being as near to zero cost as possible (Spend so far = NZ$100�ish).
The first hurdle I struck was Windows not supporting Dynamic Disks on USB drives (Required to create a spanned volume). At first I resisted using another machine (i.e. a machine running Ubuntu) as I didn't want to dedicate a piece of hardware to backing up the NAS. I then decided it would be acceptable to do this via a VM, which is what I've done.So I have 10.04 running under VMWare Server 2.0.2 under Windows Server 2008 R2. The disks are all presented to the VM. I wasn't sure if I was going to end up creating the array under LVM or something else, but I noticed Disk Utility has an option to create an array, so I tried that. When I add two 250GB drives, the array size is 500GB. When I then add a 160GB drive, the array size drops to 480GB. Huh? If I keep adding disks (Regardless of order) the final array size comes out at 1.8 TB, as per the attached screenshot. Now with the following drives, I expected something more like:
160 + 250 + 250+ 750 + 250 +200 + 200 + 250 + 320 + 250 + 320 = 3.2TB
Am I missing something or making a false assumption somewhere?
I'm running a Debian homeserver, with a 3-disk (1GB each) raid 5 array using mdadm (the OS is on a separate disk).Now, smartmontools noticed some bad sectors on one of the disks, and I'm not sure what to do next (except for backup of valuable data).I found some articles on how to fix these sectors, but I'm unaware what the result on the whole array will be.
View 4 Replies View RelatedI'm renting a dedicated server with a company that claims that the server has 2 hard drives in a software RAID 1 array, but I need to make sure that the server really has the 2 HDD, and the size of the 2nd drive... how to do that ?? system is Centos 5.3
View 1 Replies View RelatedI have a home server running Openfiler 2.3 x64 with 4x1.5TB software RAID 5 array (more details on the hardware and OS later). All was working well for two years until several weeks ago, the array failed with two faulty disks at the same time. Well, those thing could happen, especially if one is using desktop-grade disks instead of enterprise-grade ones (way too expensive for a home server). Since is was most likely a false positive, I've reassembled the array:
Code:
# mdadm --assemble --force /dev/md0 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1
mdadm: forcing event count in /dev/sdb1(0) from 110 upto 122
mdadm: forcing event count in /dev/sdc1(1) from 110 upto 122
[code]....
Right. Once is just a coincident but twice in such a sort period of time means that something is wrong. I've reassembled the array and again, all the files were intact. But now was the time to think seriously about backing up my array, so I've ordered a 2TB external disk and in the meantime kept the server off. When I got the external drive, I hooked it up to my Windows desktop, turned on the server and started copying the files. After about 10 minutes two drives failed again. I've reassembled, rebooted and started copying again, but after a few MBs, the copy process reported a problem - the files were unavailable. A few retried and the process resumed, but a few MBs later it had to stop again, for the same reason. Several more stops like those and two disks failed again. Looking at the /var/log/messages file, I found a lot of error like these:
Quote:
Apr 12 22:44:02 NAS kernel: [77047.467686] ata1.00: configured for UDMA/33
Apr 12 22:44:02 NAS kernel: [77047.523714] ata1.01: configured for UDMA/133
Apr 12 22:44:02 NAS kernel: [77047.523727] ata1: EH complete
[code]....
The motherboard is Gigabyte GA-G31M-ES2L based on Intel's G31 chipset, the 4 disks are Seagate 7200.11 (with a version of a firmware that doesn't cause frequent data corruption).
I'm currently using Windows Vista 32-bit on a RAID 1 array; I'm using the RAID provided by my motherboard so it's fakeRAID. Anyway, I'd like to do some C development under Linux but I'm not exactly sure how to go about installing it on a software RAID 1 array without messing up Windows. I'm not sure which Linux distro I'm going to install, so I'm hoping that information isn't important. Would I just resize my Windows partition and put Linux on the newly created partition? Do I have to worry about where Linux will put its bootloader or will it manage that on its own? I didn't mean software RAID, I meant fakeRAID.
View 1 Replies View RelatedWe ran out of space on our server hard drive, so I installed 2 x 1GB drives, set them up as a software RAID1 array, copied the contents of /home to it, mounted it as /home for testing. Everything OK, so I unmounted it, deleted the contents of the /home folders (don't worry, we're backed up), then remounted the array. Everything was fine until we rebooted. Now I can't access the array at all; during booting the error "mount: special device /dev/md1 does not exist" comes up twice, and manually trying toe same issue. The relevant line from fstab reads:
/dev/md1 /home ext3 defaults 0 0
However, using webmin shows only md0, the RAID0 device on which the OSD was originally installed. There is no /dev/md1 device file. The mdadm.conf file reads as follows:
# mdadm.conf written out by anaconda
DEVICE partitions
MAILADDR root
ARRAY /dev/md0 level=raid0 num-devices=2 uuid=76fd4050:fb820568:c9bd3a59:ad3e70b0
So it's not listed; I'm assuming this is significant. Am I right, and whether I am or not, what can I do?
I recently upgraded a server from Fedora 6 to Fedora 14. In addition to the main hard drive where the OS is installed, I have 3 1TB hard drives configured for RAID5 (via software). After the upgrade, I noticed one of the hard drives had been removed from the raid array. I tried to add it back with mdadm --add, but it just put it in as a spare. I figured I'd get back to it later.Then, when performing a reboot, the system could not mount the raid array at all. I removed it from the fstab so I could boot the system, and now I'm trying to get the raid array back up.
I ran the following:mdadm --create /dev/md0 --assume-clean --level=5 --chunk=64 --raid-devices=3 missing /dev/sdc1 /dev/sdd1I know my chunk size is 64k, and "missing" is for the drive that got kicked out of the array (/dev/sdb1).That seemed to work, and mdadm reports that the array is running "clean, degraded" with the missing drive.However, I can't mount the raid array. When I try:mount -t ext3 /dev/md0 /mnt/fooI get:
mount: wrong fs type, bad option, bad superblock on /dev/md0,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
[code]....
I need to access each drive of a RAID array in order to update the firmware - I am completely new to linux. I think there are probably some potential challanges along the way to get this "working" For example, it seems to me that the array may present itself to application code as a single device. I need to drill down into the RAID and talk to each physical device in turn via some sort of pass-through mechanism. I'm currently pretty lost - can anyone point me in the "right" direction
View 2 Replies View RelatedOk, as the title indicates I have a RAID5 array with 4 500GB SATA drives. This is the only drive configuration on the system (i.e. the OS also resides in the RAID array). I'm running CentOS 5 and need to know how to go about increacing the space in the RAID array by replacing the drives with 4 1TB drives.
View 3 Replies View Related1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays:
2x320GB RAID1 - used for operating systems md126
2x1TB RAID1 - used for data md125
I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only":
[Code]...
and the partition in it was not available as device special file in /dev:
[Code]...
I've tried to install Fedora 11, both 32 and 64 on my main machine.It could not install as it stops on the first install window. I've already filed a bug but really haven't seen any feed back yet.The bug has something to do with Anaconda and the Raid array but I really can't tell.
I have an Intel Board (see signature). I am running intel raid software under W7 currently.It works fine. But, I'm wondering, when I attempt to install F!!, is my current raid set-up causing problems? Do I need to get rid of the intel raid software and use a Fedor/Linux raid program to manage the raid array??
I have created a filesystem /data using software RAID-1 concept using two disks.
/dev/sdb - 50 GB
/dev/sdc - 50 GB
now i have to increase the /data to 100GB by adding two more disk.
/dev/sdd - 50GB
/dev/sde - 50GB
is this possible, if yes
how exactly i can increase the existing RAID-1 array from 50GB to 100GB.
Consider the following setup: Ubuntu system installed on a separate SSD for speed. An ubuntu software RAID array consisting of X number of physical HDD's for storage (RAID6 or RAID10). RAID setup is done during system install. If I suffer a total crash of the SSD and loose my system, will I be able to, using a new system disk, "reconnect" to the RAID array even if the "mothersystem" of the software RAID is lost? If yes, are there any particular config- or system files I need to backup to be able to rescue the array or will it just be recognized "out-of-the-box" when reinstalling ubuntu?
View 4 Replies View RelatedI am using Ubuntu 10.04 x64. I am not trying to install Ubuntu on a RAID 1 drive like all of the guides are for. I have a RAID 1 array that I am using for data storage. In windows it shows as a single array just fine. In linux it shows as 2 separate drives. I don't care how they show up to be honest I just have to data written to one drive written to the other automatically as well so my RAID isn't screwed up. Looking through different articles and forums I find a lot of stuff saying that it should show up under /dev/mapper/dxxx or something under /dev/mapper. All that shows up there for me is a device called control which doesn't seem to do something.
View 1 Replies View RelatedI just installed Ubuntu 10.10 64bit and wanted to get access to my nvidia RAID array. This array is working, and is NTFS formatted. But wasn't showing up through normal means in Ubuntu. (for example the NTFS Configuration Tool didn't display it) Here's what the system showed.
Code:
root@hermes:~# ls -l /dev/mapper/
total 0
crw------- 1 root root 10, 59 2010-11-03 22:39 control
lrwxrwxrwx 1 root root 7 2010-11-03 22:42 nvidia_dadijiag -> ../dm-0
[code]....
Is my mirror still in effect, or did i just mount one of the specific drives from the mirror?
I'm going a little bit crazy. I can't seem to remove my RAID 1 arrays. Any suggestions? I don't need to save data. The drives are empty. I'm upgrading to 4 2TB drives.Running Lucid Lynx server
Code:
jessica@nas:~$ cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10]
md2 : active raid1 sdb1[1]
976759936 blocks [2/1] [_U]
md0 : active raid1 sdd1[0]
[Code]...
Round two:I am trying to install a RAID 1 array on my system. I already have another RAID 1 array in there. I am using the BIOS RAID option to set up the array.Here's what dmraid -r tells me:
# dmraid -r
/dev/sda: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
/dev/sdb: pdc, "pdc_bajfedfacg", mirror, ok, 3906249984 sectors, data@ 0
[code]....
I installed Debian 5.0.3 (Backport with .34 Kernel), because my server hardware (Dell PowerEdge R210) needs special firmware and drivers.However, the installation went quite smooth.I put the system on a RAID 1 Array with about 500 GB space.s I said the installation went well, however, it doesn't boot! No GRUB, nothing
View 4 Replies View RelatedJust setup with Debian 8 (LXDE) a few weeks ago. Raid10 array was preexisting.
Was working well. After booting I would need to go to the save as then would need to enter the root password and everything would be good.
Can't access the array.
Used to use the command $ mount /dev/dm-o /home/myspace/folder under Debian 7.6 to mount the array (no longer works).
blkd lists a /dev/md0 but instead of UUID it is PTUUID
[Code] .....
I installed RC1, and never touched the disks that were raided previously, and the attached image is what i see for my raid array that was previously working fine.
View 3 Replies View RelatedI want to make a RAID5 array with 4 2TB hard drives. One of the drives is full of data so I will need to start with a 3 disks and then once I copy the data from the 4th onto the array, I will then add the 4th drive. This will be my first experience with RAID. I've spent a few hours searching for info but most of what I have found is a bit over my head.
View 9 Replies View RelatedI'm just about to be given a Power Mac G5 (Late 2005) Dual 2.0GHz. I think this was the last G5 produced.I plan on using it as file server/NAS and will probably run 10.04 LTS (or maybe 8.04 LTS). I would install a SATA RAID controller and run 4 1TB drives in a RAID 5 configuration. The only thing I'm unsure about is choosing a compatible RAID controller. I need to find a RAID controller that
- Is PCIe
- Is compatible with both the Power Mac and Ubuntu PPC
- Does true hardware RAID
- Doesn't cost a fortune!
Am I right in thinking that the card might need to be open firmware compatible? If it makes any difference, I plan on running the OS from a separate 5th drive. I've found this on eBay. I asked the seller and he claims it supports true hardware RAID and says the chipset is a Silicon Image SIL3124. I does seem suspiciously cheap though...
After upgrading my ubuntu install my raid array is gone. The drives appear in blkid as "Linux raid member" and both have the same uuid. If I try to mount the drive via fstab I get a message that the drive is not ready or present. If I try to mount each of the two drives, one mounts successfully the other reports serious errors. Issuing a cat /proc/mdstat shows md_d0 as inactive.How can I re-establish my raid array? I have the data backed up so if I have to wipe out the disks to start over that's an option.
View 2 Replies View RelatedI currently have a nice HTPC setup that has been upgraded from distribution to distribution since 8.xx all the way up to 9.10 now. I just moved to a new place and it feels like the right time to do a fresh install of 10.04 into the HTPC. The problem is that I have a RAID 5 array in the system that has all my pictures, videos, music, etc. This OS is installed in a separate drive that is not part of the RAID array (I have 4 drives in the system, 3 in the array, 1 for the OS). what is the general process I should follow to do:
1. a fresh install of 10.04
2. do #1 while at the same time not losing my array (don't think I would anyway).
3. what to do after install to get the array back up and running and mounted.
I am using the 10.04.1 x64 Kubuntu live CD to install Kubuntu on my FakeRAID 0 array, I tell it not to install grub as i know it is still currently broken. the install goes flawlessly. However on first boot using my live grub CD unless i tell my computer to point to the CD it will hang (which it is told to boot from CD first so i'm not sure why it does.) When i tell it to boot to Linux, it will not boot saying the kernel is missing files (to much to sadly list, all i do not understand) then offers me a terminal to input "help" into for a list of Linux commands. Windows 7 pro x64 works just fine CD was downloaded VIA P2P if it matters
View 6 Replies View Relatedrepairing the MBR on my raid array. I have three disks, each with three paritions:root (sda1 sdb1 sdc1) 59GB swap (sda2 sdb2 sdc2) 1.12GB grub/boot (sda3 sdb3 sdc3) 298MB I have been able to get this running and it has been working fine for several months. A few days ago, I installed 10.04 to a USB stick but did not disable the hard drives at that point and so the MBR was overwritten. If I leave the USB stick in, it boots fine from that stick. However now I can't get the boot from the raid array to work correctly. I can do the following:Load 10.04 from the Live CD install mdadm recreate the root partition using
Code:
mdadm --assemble /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdc1
I can mount and view the files on md0 with no problems. It's not corrupted in any way. When I installed, I followed the directions to make each of the grub drives bootable. However I don't know for sure whether grub was installed on each partition separately or if it was installed on the assembled partition only. I have tried using
Code:
sudo grub-install /dev/sda3
and got warnings, something to the effect
Code:
Cannot find a device for /boot/grub
no path or device specified
Auto-detection of a filesystem module failed
specify the module with option '--module' explicitly
I have also been able to get to the grub rescue prompt but my keyboard (wireless USB) is not recognized and so I can't type anything in at that point.
I've created a soft raid w/ 2x 1TB drives by using Disk Utility. (used for mythtv storage, not system, swap or anything else)
If I start the raid array in the Disk Utility mount and everything works as it should, but on reboot the raid array isn't started so I have to go into Disk Utility, start it, then run the mount.
How can I get it to start automatically?
I have acquired a dell 2850 poweredge server and installed ubuntu server onto only to find out we cant use linux for its intended use and need to uninstall remove ubuntu and it has a raid 5 array on the server.
View 1 Replies View RelatedI have an Areca hardware RAID array that I'm trying to format & partition on a fresh Ubuntu 10.04 LTS installation. The OS drive is not on the RAID card, it's entirely separate. The RAID is a 6TB volume so I realize I have to use parted to format it, not fdisk (which I've always relied on).
My problem is that I can't figure out how to get parted to like my settings. It seems like everything I try gives me the warning "Warning: The resulting partition is not properly aligned for best performance." Here's what I'm doing:
Code:
(parted) p
Model: Areca ARC-1280-VOL#00 (scsi)[code].....
What start/end settings should I use to get a properly aligned partition? How do I know?I have tried a mix and match of 0, 0s, 1, 1s, -0, -0s, -1, -1s, 100% for my start/end with no success.