Ubuntu Networking :: Can't Ping Default Gateway
Feb 23, 2010
I have installed ubuntu 9.04 Jaunty server from disk. I am connect to my corporate internet. I have put in my http_proxy everywhere I can find to put it. I am getting an ipaddress, gateway, broadcast,etc. My wired is connected. When I try to ping my default gateway it times out. %100 packet loss. I get the ipaddress of the gateway from the (route command).
My configurations on /etc/network/interfaces is correct(I am on another computer so I can't copy and paste) and I even tried updating the drivers for NIC card. I am using a Intel 82567LM-3. I have been working on this longer than I care to admit.
View 7 Replies
ADVERTISEMENT
Jul 2, 2010
I posted it on another forum, but could not get response,So I have this cenOS, Ubuntu and windows operating system running on virtual machines.Now I gave them manual ip address, both ubuntu and windows machines can ping the default gateway, but not the CentOS.It should forward 0.0.0.0. to my cisco router address(192.168.5.254),
View 4 Replies
View Related
Apr 29, 2010
So, I have an Virtual Machine running CentOS 5.4. It sits behind a hardware firewall which also does NAT'ing. I've set up plenty of these, so I know for sure the firewall and NAT rules are set up correctly. From the host, I can ping anything in my subnet and the gateway. But I can't ping anything else beyond the gateway. I can perform DNS queries and when I try to ping, it finds the appropriate IP address.But from the outside, I can ping the PUBLIC address (It's a 1 public to 1 private address NAT, not 1 public to multiple private). I've tried it with IPTABLES on and off, with no change.
View 11 Replies
View Related
Feb 12, 2011
I can ping my IP, and other PC in the same LAN, but I CANNOT ping the gateway on my 10.04LTS ubuntu. Other PC in the same LAN(Ubuntu 10.04LTS) could ping the gateway and my IP. I thought that (1)network cable is OK because I could ping the other PC in the same LAN.(2)Gateway is OK because other PC could ping it. (3)setting of operating system might be somehow wrong.
I have tried to restart the network several times and still not works. I followed the HOW-To debug tips and following is the results. Any suggestions?
1. ifconfig
eth2 Link encap:Ethernet HWaddr 00:1d:7d:aa:d5:d3
inet addr:140.112.61.75 Bcast:140.112.61.255 Mask:255.255.255.0
inet6 addr: fe80::21d:7dff:feaa:d5d3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 2 Replies
View Related
Jul 17, 2011
I installed openSUSE on one of my work system. The network port wasn't working when I was installing, but works fine now (checked in Windows). But for some reason, I am not able to configure the network. I used both Dynamic and Static IPs (both work fine in Windows) but still no go. I am using Yast Control Center for this purpose. I can't even ping the default gateway when I am using custom settings. When I use dynamic settings, it says Unreachable Network.
View 7 Replies
View Related
Mar 8, 2010
My problem is simple, iam runing ubuntu 8.04 (ebox 1.4) , i have installed and configured PPTPD server, i can connect and ping users perfectly. BUT i dont getting any gateway address, in my case i have to get IP address 172.16.0.1 (PPTP server address).I tried to change localIP in pptpd.conf to 0.0.0.0 ,or my remote(ISP) address but nothing.Can someone explain to me how can i manually assign gateway IP address to PPTPD Server ???
View 1 Replies
View Related
Jul 11, 2011
I am trying to get a Linux (Slackware 13.37) working in a Windows networking environment. The IT support for this organisation does not extend to Linux support, so I'm limited in what help I can get for this.
I'm trying to get to the point where I can get to the internet to download what I need on this Linux machine.
The situation is this (*fictitious addresses used) -My Linux machine uses a fixed IP address (10.100.150.21)
My Windows machine uses a DHCP assigned IP address (10.100.150.213)Both Linux and Windows machine are configured to access the gateway server (10.100.150.1)So, I can ping the Linux machine from the Windows machine and vice-versa.I can ping the gateway machine from the Windows machine.I can browse Windows Shares on the network via SMB from the Linux machine.I CANNOT ping the gateway machine from the Linux machine with the Destination Host Unreachable message being the error message.
For actual internet access I need to access a proxy server but since the Linux machine can't even ping the gateway server, it fails to ping the proxy.Now, I have been told the gateway is a HW based router and for Windows machine they use some software for authentication to connect to the network. This software isn't available for Linux, so that's why I've been told to use a fixed IP address.My experience of networking is pretty basic and most of the Linux setup is done via running Slackware's setup program.
View 12 Replies
View Related
Jan 22, 2009
Presently this client access the net through following setup
ADSL modem -> hub -> all computers
Now they want to do some kind of bandwidth control, content filtering. So I tried setting up squid with dansguardian. This is what I did
ADSL -> linux server -> all computers.
The linux server has two NIC cards. One to the ADSL router and another to the local hub. This is how my squid.conf file looks like
http_port 3128
acl ubc src 192.168.1.0/255.255.255.0 (for subnet)
http_access allow ubc
Have set the gateway server as 121.x.x.1. Which is the gateway server of the ISP. Now I can ping the local network, but cant ping the gateway or any other website. Also I am unable to access the router administration page.
View 2 Replies
View Related
Feb 3, 2011
This is slackware 12. I'm trying to share my internet connection (on eth0) with a computer connected to eth1.
eth0 is 192.168.0.101, eth1 is 192.168.1.100 (different subnets).
But when I try to make eth1's default gateway the same as eth0's, see the error I get code...
View 7 Replies
View Related
Jan 8, 2010
I am in a big confusion and searching an answer to calm down my mind.I have my eth0 has following configuration
` ` `
IP 192.168.1.100
mask 255.255.255.0
[code]....
View 3 Replies
View Related
Jan 30, 2011
I had a router crap out yesterday. I'd been testing out a new one for the last few days and just reconfigured it to be the main. Took the old one down and everything in my house (Windows 7 PC, XP Files server, Ubuntu PC , windows 7 laptop, android tablet, ps3, etc) seems to be working fine whether it be hard wired or wifi. All except my ubuntu 10.04 laptop. It worked fine before the swap so I can't figure out what's going on.
I'm able to connect to the new SSID without issue but I can't resolve any external names and when I try to ping the default gate way every other packet has (DUP!) behind it. If I'm hardwired I don't get the dup! when pinging the default gateway but I still can't resolve any external names. I have provided the results of an ifconfig and the results of a ping to the default gateway below.
cooley@Quigon:~$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=2.98 ms
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=3.04 ms (DUP!)
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=3.50 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.72 ms (DUP!)
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=8.09 ms
[Code]...
View 9 Replies
View Related
May 4, 2011
Im trying to achieve the multiple uplinks/provider found on LARTC.org. I have to get the IP addresses from my interfaces (EF1 and EF2) by using a script, but i dont know where to look at for the default gateway from each interface which got their ip address from my ISP.
View 1 Replies
View Related
Apr 11, 2010
I have a computer with two interfaces: a fixed connection (eth1) and a modem (ppp0). My goal is to receive UDP packets from both connections concurrently (using the recv() function). The problem is, that the received packets reach the application only when the default gateway is set to that interface's address. For example, if I set the default gw to be in the eth1 subnet, only packets from eth1 reach the application. Other packets are received in the interface (checked using tcpdump), but they seem to be blocked somewhere. The policy defined in iptables is "ACCEPT" for all incoming packets, with no rules at all. I would like to know how to overcome this problem, and anyway how is the default gateway related to incoming UDP?
View 3 Replies
View Related
Nov 11, 2010
I have a dual-homed Debian server running squid, but not acting as a router. Simplied network diagram is below - there are other local hops between the gateways and the Internet.
Code:
(eth0 @ 192.168.44.2) <--> (Gateway1 @ 192.168.44.1) <--> Internet
(eth1 @ 192.168.55.2) <--> (Gateway2 @ 192.168.55.1) <--> Internet
Using Gateway1 gives a very fast, but not always reliable route to the Internet. Using Gateway2 gives a slower, but more reliable route to the Internet. The server uses Gateway1 as the default gateway.
I have written a script that pings three hosts on the Internet, and if all three are down, switches the default gateway to Gateway2. This part seems to be easy, but I'd like know if there is a way of routing a ICMP/ping out eth0 to a host, with all other traffic to the host going out eth1, so I can determine if the Internet is reachable via Gateway1 again.
View 2 Replies
View Related
Apr 7, 2010
I am realtively new to BGP. I use BGP in my network to advertise my /20 subnet. What i would like to know is what is the point of accepting routes from your neighbouring AS(ISP)?My ISP has given me a default gateway, and no matter what I want to reach on the internet I have to go through that default gateway, so why populate the routing table with soo many routes?also, as i understand it, there are 3 kinds of routes that you can accept, those are full routes, directly connected routes and default routes. What is the diffrence between them and again how do they affect routing since my network only has the one default gateway?
View 2 Replies
View Related
Oct 22, 2010
Back in April I set up a Ubuntu DHCP server and a multiple VLAN network [URL] to migrate our various servers, workstations, etc off the 192.168.1.1 /24 network that everything was on because we where running out of address space. I built out the new network and everything worked great except our AD server would never get an IP address from the DHCP server (static reservation) and even if I set the IP statically on the AD server it couldn't ping the gateway and noone could log in. After several attempts to resolve this, including bringing in outside help, we where never able to figure out what the problem was.
Now 6 months later I have time to revisit the issue without effecting the live network. I used Acronis and imaged the AD server last Friday, cloned it on to another box with the same hardware, and put it up on the new network that's been sitting unused for the last 6 months. Today when I statically set the IP on the AD server (which is what I want) it connects and I can ping it's gateway 192.168.1.1 and all the way across vlans to a test sales agent workstation at 192.168.8.xxx on vlan 800 but only if I statically assign the agents station an IP address. When I try to get an IP address via DHCP it fails as destination unreachable. Nothing has changed in the last 6 months on the DHCP server but now it for some reason can't ping its default gateway 192.168.1.1. All of the config files are the same as they where left from the post linked above aside from the vlan id's used where changed from 1's to 100's (i.e. vlan 3 is now vlan 300) /etc/network/interfaces
Code:
auto lo
iface lo inet loopback
auto vlan100
iface vlan100 inet static
[code]....
why it can't reach the gateway, when I do a tcpdump I can see the DHCP requests come in on eth0 but the server never responds and I'm pretty sure its because it isn't "seeing" them since it thinks there isn't a network connection but I don't know how to trouble shoot to find out where the problem lies.
View 6 Replies
View Related
Jul 1, 2010
Back in April I set up a Ubuntu DHCP server and a multiple VLAN network [URL] to migrate our various servers, workstations, etc off the 192.168.1.1 /24 network that everything was on because we where running out of address space. I built out the new network and everything worked great except our AD server would never get an IP address from the DHCP server (static reservation) and even if I set the IP statically on the AD server it couldn't ping the gateway and noone could log in. After several attempts to resolve this, including bringing in outside help, we where never able to figure out what the problem was.
Now 6 months later I have time to revisit the issue without effecting the live network. I used Acronis and imaged the AD server last Friday, cloned it on to another box with the same hardware, and put it up on the new network that's been sitting unused for the last 6 months. Today when I statically set the IP on the AD server (which is what I want) it connects and I can ping it's gateway 192.168.1.1 and all the way across vlans to a test sales agent workstation at 192.168.8.xxx on vlan 800 but only if I statically assign the agents station an IP address.
When I try to get an IP address via DHCP it fails as destination unreachable. Nothing has changed in the last 6 months on the DHCP server but now it for some reason can't ping its default gateway 192.168.1.1. All of the config files are the same as they where left from the post linked above aside from the vlan id's used where changed from 1's to 100's (i.e. vlan 3 is now vlan 300) /etc/network/interfaces
Code:
auto lo
iface lo inet loopback
auto vlan100
[code]....
why it can't reach the gateway, when I do a tcpdump I can see the DHCP requests come in on eth0 but the server never responds and I'm pretty sure its because it isn't "seeing" them since it thinks there isn't a network connection but I don't know how to trouble shoot to find out where the problem lies.
View 2 Replies
View Related
Feb 21, 2011
I'm looking for a method to assign a default gateway via dhcp randomly depending on ether the last char of the mac being odd or even, or the time the user connects. Is there a good reliable way to achieve this?
View 2 Replies
View Related
Jun 16, 2011
I have installed dhcp-server on ubuntu. And server is providing ip address to clients (Window machines) but not default-gateway but I have another network in my network and same configuration and same dhcp-server provides every information.
View 5 Replies
View Related
Oct 21, 2010
I've been struggeling with this for a few hours now, googleing and so on trying to find an easy way to just switch which device I want as primary for internet connections. After long battles I'm at a loss, this is the current automatic routing
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
85.225.76.0 0.0.0.0 255.255.252.0 U 1 0 0 eth0
85.225.76.0 0.0.0.0 255.255.252.0 U 2 0 0 wlan0
[Code]...
View 1 Replies
View Related
Jun 29, 2011
I need to place an Ubuntu machine on a network where I have a DHCP server which does not configure the Degault Gateway parameter (we don't want ordinary users to browse the internet). Is it possible to leave the machine using DHCP and define the Default Gateway manually (as in Windows XP i.e.)? How?
View 1 Replies
View Related
Mar 9, 2011
Struggling to get my Linux server accept ICMP redirects not originating from default gateway. No problem to get it working if the redirects is originating from def gw.I know it's not a good solution security wise, but my network is so cluttered I'm forced to do so.
View 1 Replies
View Related
Nov 26, 2009
Client which uses an ISP with a Linux machine (Server 1) with two network cards. Eth0 with ip 1.1.1.2 and gateway 1.1.1.1 these ip's is not public ip's and falls unders the isp's internal range, eth1 with the internal ip range. OpenVPN listen on eth0 for incoming connections. We want to connect to Server1 from external networks. Due to different reasons the isp could not get the routing sorted and give us an public ip on his network. We had to setup another bos (Server2) with eth0 2.2.2.5 and gateway 2.2.2.1 which is public ip's and eth1 with ip 3.3.3.5. Server 2 can communicate via the ISP internal network with server 1. I use DNAT to forward all incoming connections on server 2 to server 1 but the problem I have is that server uses its default gateway for the return packages and does not sent the reply back to server 2. My iptables rules looks as follows on server 2.
/usr/sbin/iptables -t nat -A PREROUTING -p udp -i eth0 -d 196.25.157.135 --dport 1194 -j DNAT --to 192.168.100.170:1194
/usr/sbin/iptables -A FORWARD -p udp -i eth0 -d 192.168.100.170 --dport 1194 -j ACCEPT
View 5 Replies
View Related
Apr 22, 2009
I'm using OpenWRT on a WRT54GS. I'm using wifidog in combination with openvpn. For those of you familiar with wifidog, my auth server is located at the other end of an openvpn tunnel and the "wifi dog gateway" is running on the WRT itself. I'm don't really think that wifi dog is the issue. Basically, I'm using openvpn with the "redirect-gateway" option which works well. In this mode, openvpn removes my current default gateway setting and adds the remote openvpn server as the default gateway (as it should). However, overnight, my default gateway on the local network keeps reapperaing (along with the openvpn one as well).
This causes confusion and I don't want any packets (But ovbiously the connection to the actual openvpn server) to go down this local gateway. Why do you think it reappears? Do you reckon openvpn is dropping connection and somehow the normal gateway is being added back? I *could* run a cron script which runs every minute or so with something like "route del default gw xx.xx.xx.xx" (where xx.xx.xx.xx is the default gateway which I don't want to be there) but that is quite messy and means that if I were to ever move the router I would need to reconfigure this and considering that I would like in the future to have many of these wifi dog gateways, this really isn't an ideal option (as every network will have a different default gateway).
View 2 Replies
View Related
Dec 19, 2010
I could not able to configure the default gateway ip address onto the system. i use the route command (" route add default gw 192.xxx.xxx.xxx eth0 ") to add a default gateway onto the routing table but it is "disappear" in the routing table when i had restart the service network.
View 3 Replies
View Related
Jul 15, 2011
I am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
View 2 Replies
View Related
May 6, 2010
I am accessing internet through Analog Proxy. ADSL modem has been connect to one of windows xp machine and by running Analog proxy, we uses internet by mentioning that machine's ip address. But how do i ping the default gateway in this case? Is it possible or not? If yes then please tell me how, because if i says # ping <anysite.com> it not pinging; its says host unreachable; means i will not be able to run wget too.
I am trying to ping from OEL 5.3. In one of google link; i read that :Does PING work through the Proxy Server? No, ping uses the ICMP protocol to communicate. Proxy only supports TCP and UDP packets. Ping will resolve the DNS name but go no further.
View 5 Replies
View Related
Jun 14, 2011
I have configured bonding on 64 bit centos 5.4 I have to put the machine to a different VLAN for that i did the Ip change and restated the network. but i cant ping the gateway or any other server in that network. the cofig files are as follows
vi /etc/modprobe.conf
alias eth0 bnx2
alias eth1 bnx2
alias scsi_hostadapter aacraid
alias scsi_hostadapter1 ata_piix
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
alias bond0 bonding
options bonding mode=1 miimon=100
[Code].....
View 5 Replies
View Related
Oct 25, 2010
When using gateway 196.214.15.X with ip 192.168.1.X all windows pc connect to internet and email but using the same range on rhel5 it cant even ping mailbox. Why is the ip masked, can u get software to trace the ip of the gateway from the windows pc, the 196 ip is I suppose a public ip as it is the ip of my lease line? How do I get the RHEL5 running internet using the same range as the windows boxes ??
View 2 Replies
View Related
Jan 6, 2009
Set up new server using RH 2.6.9-42.ELsmp on an old HP G4 server. But can't get network to work, can't ping any host, not even my gateway.
Verified cable by plugin a different pc on it, using same network ip address, etc, it worked fine, could ping gateway and other hosts on same segment. Are there any other files I could check to verify network card on server is good? it was working when it was configured as a windows server.
View 1 Replies
View Related
