Ubuntu server 9.10. I have configured my network connection using GUI Network connection. It worked fine with DHCP, but when I assigned a fixed IP eth0 has disappeared. How can I restore it?
View 3 Replies5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
I was struggling frantically this morning for about 5 minutes after I booted up my computer, and wondering why it couldn't connect to the internet. After I figured out that the automatic wired network "Auto eth0" was gone from the network manager, it was easy to manually add it back. But why did it disappear in the first place?
View 3 Replies View RelatedI have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
I have trouble getting a gateway to the internet when setting eth0 with a fixed IP address. The gateway address (192.168.2.1 my modem/router) resets to 0.0.0.0 whenever I apply the changes. DHCP works fine but I need a fixed address for my server.
View 6 Replies View RelatedI did an weekly update through aptitude, and it asked for a restart.after the restart, there was no ethernet available. ifconfig brought absolutely nothing, as though the card was no longer present This is on an old dell tower. How do I find out what happened. I don't know how to find out what was in the update.
View 8 Replies View RelatedI try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.
1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them
[code]....
I'm running 10.04 and my eth0 connection disappeared. If I go into my network tools, I can see the IPv4 connection and test the ping and all. When I go to my network connections, I do not see the eth0 at all. I have not made any serious changes lately and have no clue to what could have caused this. I have tested the cable with my laptop, and it works fine. I have serious reddit browsing that needs to be done!
View 3 Replies View RelatedAfter rebooting, I found that the server couldn't see the network. The machine has dual gigabit ethernet (eth0 and eth1). eth0 is connected to the internet, but disappeared. ifconfig used to show eth0, eth1, and lo, but now only shows eth1 and lo. If I boot into rescue mode I can get internet and ifconfig returns eth0 and lo. Any ideas on how to fix this?
I apologize in advance if I ask any noob questions. I'm not a very experienced Linux user.
I got two IP's in my dedicated server. Both are external IP's. I would like to make connections using 2nd IP address under eth0:0 interface. For example: when using "lynx whatismyip.com" should display my 2nd IP. How to do this using iptables ?
View 1 Replies View Relatedi know exactly what i need to do, im just not familiar enough with command line to do it properly.i have 7 computers.the first 4 are connected to a router via wireless at one end of the house. of the last 3 only 1 will be able to access the router via wireless, so it needs to share it's one wireless connection via ethernet. this computer i'm going to call 'server'server will have two IP'swlan0 192.168.1.6 this connects to the router that has internet access.eth0 i intend to have the following settingsip:192.168.0.1sub: 255.255.0eth0 will connect to a second router, where the cat5 cable goes from the server, into the internet port of the router where i will define the router's static IP:IP: 192.168.0.100sub: 255.255.255.0gateway 192.168.0.1i have then set the router IP for LAN handling as 192.168.27.1 and all ethernet connections will have a 192.168.27.x IP.
so i need to know how to, without a gui application, use the terminal to assign server eth0 a proper IP address, and tell the server to take the connection it has and share it through eth0 to supply internet for the last 2 computers via ethernet.i had it set up in this way with a windows machine being the one that had the wifi access, but i'd rather have it setup for the ubuntu server to do this task. security is imperative for these 3 remaining machines, so just getting 2 more wifi adapters for a connection to the initial router isn't an option.the 2 that connect to server do so through SSH and though server IS connected via wireless it only makes outward connections through
I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.
ifconfig eth0:
Code:
eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
Since I have a new internetaccount, 2 days ago, I have a problem on my server [Fedora Core 8]. I use it as a router.
eth0 is for the internet.
eth1 is for my LAN.
But since my new internetaccount my server uses eth1 for the internet. This is a line from my syslog:
Code:
NetworkManager: <info> Policy set 'System eth1' (eth1) as default for routing and DNS. I killed the NetworkManager daemon and now it works but this must not be the way to do it? Where do I tell my server that I use eth0 for routing and DNS?
I added an init script numbered just before bind9 starts, which needs to see the ipv6 link-local address on eth0. Sometimes this address is not configured, yet. In all cases it eventually is configured.
I am unable to find any script that is configuring the ipv6 link-local address (which is in part based on the MAC address). Does anyone know if there is some script or program that is supposed to be doing this, or is it an internal kernel function?
One workaround I am considering is making this init script go into a loop around sleep 1 to keep checking for the ipv6 address. But I'm concerned this might cause some problems. Any suggestions? I don't want to let it move on to start bind9 until the configuration this script does (more ipv6 addresses) is done.
This is on Ubuntu 9.10 server (for which there is not a prefix choice).
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
I want to set up a dhcp server such that the clients get same ip every time. Giving fixed address to every client would be a long process.
"I don't want to assign a specific ip to the client but what i want is the server provides same ip every time"
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedOur router is pretty old and only capable of giving fixed ip and there is no support for IPv6. Via the gnome networkmanager I try to set a manual IP to 192.168.1.123 and a netmask to 255.255.255.0 and a default gw at 192.168.1.1 . However, this does not work.
If I open a terminal and type:
Code:
sudo ifconfig eth0 inet 192.168.1.123
sudo route add default gw 192.168.1.1
Then I get a perfectly valid connection to the internet.
ifconfig by it self returns:
[Code]....
ffor me it seems that the gnome network manager doesn't save the information that I gently ask it to.
I can fix it with the CLI commands, but I would like to know whats going on.
I am new to Linux so thought it would be a good learning exercise to try and setup an FTP server using linux.I have downloaded and installed Ubuntu 10 server edition and installed vsftpd, following instructions found on here I have configured the software and I can connect from an FTP client on my windows PC across the internal LAN.I have a couple of questions if I may:
1) a post on this forum suggests that local users can access the FTP server if the correct line is enabled in vsftpd.conf - I have done this and the fact that I can access it shows this is working I would think, however users added subsequently with the useradd command cannot access the server. Filezilla shows a could not connect to server error.
2) how do I give the server a fixed IPv4 address? It is currently using DHCP
3) I need to be able to put files into users folders for them to access offsite, but I don't want them to see each others filesfolders, can I do this?
Ubuntu LTS 8.04 + DHCP. Works fine except for fixed addresses. I mean all devices which need to get fixed IP according to their MACs don't get them and keep to receive random IPs from the range (although almost everytime all machines receive the same IP they got from DHCP for the first time).
The following config was created by Webmin interface.
At the one of the ubuntu forums i was advised to carry host description out of the subnet description.
I am trying to audit my wireless router due to someone in the neighbourhood hacking it, and have run into a few problems. When I run airodump-ng, everything works fine. However, when I try to get the .csv file and run "airodump-ng -w test --channel 6 --bssid ---------- mon1" (obviously with my the mac address of my AP instead of x's) I get this:
CH 6 ][ Elapsed: 4 s ][ 2011-02-02 17:48 ][ fixed channel mon1: -1 ] The problem is the [ fixed channel mon1: -1 ], because when I go to the next step to try to force a handshake, it says:
18:00:34 Waiting for beacon frame (BSSID:-----------) on channel -1
18:00:34 mon1 is on channel -1, but the AP uses channel 6
I have scoured the Internet for answers, and have seen several people with the same problem, but no solutions that work for me. I think it may have something to do with the driver. I really do apologise if this has been answered properly several times, but none of the solutions seem to be working in my case.
I would like have a password for accessing my web site which works fine. I also want for the specific site to allow access only for a specific range of ips. Right now the following config should forbid my access, as my ip is different from 200.200.200.*
View 6 Replies View RelatedFor some time, I've had DSL and used Fixed-IP internally. I moved, no DSL, no cable, no nuthin' but dial-up and flaky cell-phone modem. Ugh. Along comes American Recovery and Reinvestment Act providing funding for making high-speed internet available to those of us in the boonies; no up-front or monthly equipment costs, affordable monthly changes, whoo-boy, that's for me. Installed, works, bada-boom, bada bing.
I have three servers, a network printer and a large format pen plotter that have all happily played together with fixed-IP for years connected via a Linksys BEFSR41 router and CAT-5 or CAT-6 cables and I do not want to screw around with DHCP (and the printer and plotter don't particularly like DHCP in any event). The servers talk to each other with SSH, their names and addresses are in /etc/host and all has been well with the world. DSL connected with PPPoE, HughesNet connects "automatically" to the modem with DHCP. I also have a switch available for additional LAN stuff as needed. Of course I had to do a hard reset of the router when setting up HugheNet (right back to infancy).
I do need to have DHCP enabled in the router for the limited occasions that a Winders thing gets connected to it (not my box, I don't mess with it).
Now, the actual question: is there any setting in the router that will enable fixed-IP, ignore DHCP leases unless the server is running DHCP (like a Winders box) and not bother me with screwy lease addresses that override my fixed-IP addresses? My servers are running Slackware 13.1, all configured with fixed-IP, all configured to "know" each other via /etc/hosts, /etc/resolv.conf has DNS Server address in it (and DHCP is not permitted to overwrite /etc/resolv.conf.
Assume I installed originally CentOS Desktop with IP receiving from DHCP server.Later I decided to assign a fixed IP to the local CentOS installation.How do I switch (permanently) the dynamic DHCP IP assignment to a fixed IP?
View 1 Replies View RelatedI boot some Slackware with PXE. All work fine except i can't fix the client lockd ports.NFS is compiled inside the kernel, so all modprobe.d options are useless.But rpcinfo -p on the client side shows me totally different ports.On the NFS server, the ports are ok, as i appended lines in /etc/lilo.conf Server and client kernels/modules are identical.
View 1 Replies View RelatedWhen I install Fedora 10 on a new system, I let it default to DHCP. Later, I change the system to a fixed IP address by running system-config-network, selecting eth0, clicking on "Edit", clicking on "Statically set IP addresses:" and filling in the blanks. Is it possible to accomplish the same thing using commands that could be entered in a script? I assume one of them would be
Code:
ifconfig eth0 address XXX.XXX.XXX.XXX netmask 255.255.255.0
I have a hardware device with two ethernet ports, eth0 and eth1 running Centos 5. Basically my goal is to forward packets from eth0->eth1 and eth1->eth0 as well as get a copy of these packets for analysis. If I set IP routing to do the forwarding then I won't get a copy of the packets for analysis.
View 3 Replies View RelatedIt seems with the newer linux headers, two functions changed their names slightly and caused a crash when attempting to build the Asus-provided USB-N13 drivers.
I'm still in the middle of getting the device to work, but actually compiling the driver was a major problem for me and others I've seen that complained of the breakage in 10.10.
Here's the fix:
Within the include/os/rt_linux.h and os/linux/rt_usb_util.c files, the usb_buffer_alloc and usb_buffer_free functions are part of an internal macro. These functions do not exist anymore and are replaced by the usb_alloc_coherent and usb_free_coherent respectively. Input parameters did not change, just the names.
The macro is defined in rt_linux.h and the functions are used in a symbol export within rt_usb_util.c. Simply renaming the functions should allow it to build.
As I said, I'm still in the process of getting the wireless to work, just wanted to let everyone know of the quick fix.
This issue will probably be addressed with a macro fix somewhere eventually.
#define usb_alloc_coherent(a, b, c, d) usb_buffer_alloc(a, b, c, d)
#define usb_free_coherent(a, b, c, d) usb_buffer_free(a, b, c, d)
If I uncheck and recheck "Enable Networking" in the Network Manager Applet 0.7.996 I would expect the wired network to disconnect (which it does) and reconnect (which it does NOT). So I tried sudo ifdown eth0 and got
Quote:
Ignoring unknown interface eth0=eth0.
ifconfig tells me
Quote:
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
so I am at a loss. How do I stop and restart the network interface short of rebooting the machine?
I have set up a nis slave server on Fedora 14. It was set up on a laptop so that the user can log in when he is at home (no NFS, local home dir). However, whenever the eth0 is disconnected, ypbind fails.
I have tried the same setup on a RHEL 4 (configured it as a slave server) against the same master nis as on the Fedora 14. Disabling eth0 on it however does not fail ypbind.