Ubuntu Networking :: 10.10 - Very Slow Wireless Speed
Mar 28, 2011
I have very suboptimal Internet speed in Wifi with Ubuntu. Normally in WIndows 7 I get download speeds up to 800 KB/s and a very fast Wifi experience, but in Ubuntu I get 100KB/s maximum and web page load speed is very extremely slow. Also, pinging to AP often gives very high response times and a lot of lost packages while in Windows they are very low and none packages are lost. I have a Netgear wg111v3 which worked out of box when I installed Ubuntu but always with this problem. It is updated and I've reinstalled Ubuntu many times..
Also I forgot to say that in Ubuntu the connection goes down very often and sometimes will not connect again until I reboot. Again in Windows never happened that.
Motherboard: GA-MA74GM-S2H
CPU: AMD Athlon 64X2 dual core
2 GB RAM
Ubuntu 10.10 64 bit
Wireless adapter Netgear wg111v3 USB .....
View 9 Replies
ADVERTISEMENT
Jan 15, 2010
I've been using Ubuntu 8.04 for about a year and the wireless has been fine but now it's gone screwy and I can't figure out why. This has happened on my laptop and wife's who uses Ubuntu Hardy also. The speed drops to almost 0 mb/s whenever the signal strength is less than 95%.
It isn't the internet connection as vista (I dual boot) works fine below 95% signal strength. To get the internet speed to be at a level that can load an internet page, I have to within 3 feet of the router!! Both of the laptops don't use ndiswrapper, the internet connected straight away from a fresh install.
View 2 Replies
View Related
Jun 5, 2010
Basically the problem is a slow download speed over my wireless connection that does not occur in Windows Vista. The reason I'm so annoyed is that the speed is not constantly slow. It bursts at around 600kb/s (good for my internet connection). The problem is that while trying to download a file it bursts for about a second,then total throughput decreases to +/- 1kb/s for a few seconds, then another burst and so on. Note the file I'm downloading is a http:// download, not p2p or anything. I've attached a screenshot of the System Monitor.
Screenshot-System Monitor.png
Some additional info. I'm using Ubuntu 10.04 with all available updates installed. The browser in use is Google Chrome.
View 9 Replies
View Related
Oct 1, 2010
i have a zenda w322u usb wireless adapter that gives a good connection to wireless router but seems to give very poor download performance compared to my laptop. Are there settings that i can access for this adapter to improve its performance.
View 6 Replies
View Related
Feb 10, 2010
When using launchpad and the ubuntu daily build website it is very slow. I get 1.2mb/s normally and the speed drops quickly to 0kb/s This is the case from any version of ubuntu that is installed on my laptop.In windows it is no problem, equally there is no problem from a live cd or an install on my external hard disk. Is canonical blacklisting/slow listing my ip?
I am behind a university network but am sure this problem occurs at home .I did a clean install and had no problem until about an hour ago. When I tried to re download a project using bzr my speed instantly ropped.I had downloaded it fine a couple of hours ago. I hope that someone can shine some light on this, its very hard to work on projects if I can't download them.
View 5 Replies
View Related
Feb 7, 2010
I'm experiencing slow speed transfer between two wireless connected laptops running ubuntu 9.10. Using SSH to tranfer files between these two laptops, which connect to the internet via a wirelesss router, with good speed. This is why I'm surprised by this low speed : 52.3 KB/s, averaging 3 hours and 31 minutes for a 700 Mb movie. Is there any way to make this faster ?
View 3 Replies
View Related
Oct 14, 2009
We have a server and we have instales an Open suse 10.3 on it. We created a Samba server also. Made to share folder, that we acces from network from other computers that have xp.
The problem is if we try to copy from server it is very slow only 100-300kb/s. The strange thing is that if i copy 1 file then its slow but if i start to copy another one the speed gos up to 10-15mb/s. Evry time i want to copy somethin or install from that server i need to start another copy. If i copy from a comp to that server the speed is normal only if i copy from server its slow.
View 3 Replies
View Related
Feb 8, 2010
I replaced only my mainbord and cpu and Ubuntu 9.10 boot just fine. The only issue that I have is that my connection speed dropped from 10Mb to 3Mb. I try the connection on my laptop and it is fine 10Mb, so the problem is with the PC. What else to try before reinstall Ubuntu as a final step?
View 3 Replies
View Related
May 5, 2010
I'm running Kubuntu 10.4, and I'm having a really slow Internet connection, with Windows everything works fine.
When I upload a file to an internal Ubuntu server the speed is ok ~15MB/s.
The problem is only with Internet Firefox / synaptic, any program using Internet. Last download done with synaptic display 18KB/s when normally it should be 500.
View 9 Replies
View Related
May 4, 2011
In mi fstab file I mount a smb file server at boot. The code is:
//<ip address>/data /home/eng-2/NAS smbfs credentials=/home/eng-2/.smbcredentials,dir_mode=0775,gid=1000,uid=1000 0 0
Transfer rate to the server is approx 100 KB/s
Whilst transfer rate from the server 16 MB/s
If I mount it from Places>connect to server. Both to and from speeds are 16 MB/s. Why is it so slow when mounted through fstab?
View 2 Replies
View Related
Jul 5, 2011
I am hoping someone can help me I setup a brand new ubuntu 11.04 64bit system with:-AMD Phoenom 840 (3.7GHz overclocked) 8GB DDR3 RAM.WD20EARS x 4madmin (RAID5) SetupFor some reason I cannot get the write speed above 15mb/s & I have tried modifying the cache_Stripe_size from 256 to 8192.My read speeds are great burst at 120mb/s & stable at about 60mb/s.The only other possiblility is it could be my HDs which I read causes slow writes not sure if thats true though. point me in the right direction so I can fix this issue as I don't want to move to the dark side (Windows) .
View 1 Replies
View Related
Jul 30, 2011
So i am very new to linux based OS. Just started getting used to the terminal. but my problem is i am trying to install a game on steam and it is downloading very slow. i am used to getting close to 700 kb/s on windows 7 but on ubuntu 11.04 i am only getting 170-180 max. now i have searched all over and tried to fix it on my own but i just cant figure it out and am getting very frustrated. so if anybody has an idea as to how to fix this it would be greatly appreciated. (have looked through the forum by the way but as i said im new to linux and im not actually sure if im looking at the right things) but im using a wired connection. it says im connected to something called auto etho. and there is something called a loopback connection or something like that.
View 2 Replies
View Related
Aug 5, 2011
I'm running 11.04. I have brought a new WiFi adapter, ralink rt2070. When I browse the internet, it takes a long time to load a webpage. When I download updates, it goes at 3,060 BYTES a second. Is there any solution? I'm using the default rt2800usb driver.
View 9 Replies
View Related
Feb 5, 2010
I am experiencing very slow speed with the Intel 5300AGN on a Dell Studio XPS notebook and the iwlagn driver. I'm using Fedora 12 with all the latest updates available. When connecting to a G network with WPA2 security, everything goes fine at "normal" speed. When connecting to a N network with WPA2 security, the download speed falls between 0 k/s and 20 k/s max. The connection speed (as stated by Network Manager and iwconfig) is between 0 kb/s (?) and 11 Mb/s during the same session. I'm can't connect through ssh or download with scp (stalled). Web pages take a lot of time to render.
When connecting to the same N network on Window 7, everything runs fine enough. Every N network I try is the same story. Works fine on windows, badly on F12..
[Code]...
View 9 Replies
View Related
Apr 22, 2010
I have problems with my network speed when i ping my proxy server I end up getting a high packet loss generally more than 30%.I have tried to use various network monitoring softwares like etherape, wireshark, tcpdump but I am not able to get to the bottom of the problem.basically I am trying to find out where the lost packets are going.
View 7 Replies
View Related
May 18, 2010
A lot of people have the problem to find themselves with Lucid Lynx 10.04 and experience massive issues when connecting to wireless - me too. As a service, here some relevant links which promise relief:
[code]...
I tried all of them, and none reliably worked. Every solution which required re-association wtih the AP helped for some time, but nothing helped for long. First, don't let yourself fool by the disable IPv6 trap - while it is "enabled" it is acutally not used by Lucid! I have a clean install of Kubuntu 10.04 on an AMD64 Laptop with Broadcom STA driver: 03:00.0 Network controller: Broadcom Corporation BCM4328 802.11a/b/g/n (rev 03) However I can reliably stabilize my connection for some time either by manually disabling WiFi with the hardware switch or disabling WiFi by software means and re-activating. This brings speed at par with Kubuntu 9.10 until some time. Can anybody confirm this behaviour?
View 9 Replies
View Related
Jul 6, 2010
I just tried NFS for the first time after reading that it's considerably faster than SSHFS, which I currently use, but I'm experiencing slow write speeds and problems while copying files in nautilus.
[Code]...
View 1 Replies
View Related
Aug 4, 2011
I had a F14 samba server working flawlessly now for a quite time. Unexpectedly about a month ago the write speed slowed down around 64kbit/s and that's really slow. I haven't changed any configs, only updated the server. I've troubleshooted this from many angles:
-It is not a network issue because sftp writes are good.
-It is not a RAID1 issue because write speed from another directory (locally) are good.
So basically samba is the only thing left.
Here's example from smb.conf:
[MyShare]
comment = My share
path = /mnt/RAID_share
writeable = yes
browseable = yes
writelist = +smbuser
Here's a snip from logs today:
[2011/08/04 09:04:27.509273, 1] smbd/server.c:267(remove_child_pid)
Scheduled cleanup of brl and lock database after unclean shutdown
[2011/08/04 09:04:47.526336, 1] smbd/server.c:240(cleanup_timeout_fn)
Cleaning up brl and lock database after unclean shutdown
[2011/08/04 09:17:57.634660, 1] smbd/server.c:267(remove_child_pid)
Scheduled cleanup of brl and lock database after unclean shutdown
[2011/08/04 09:18:17.635196, 1] smbd/server.c:240(cleanup_timeout_fn)
Cleaning up brl and lock database after unclean shutdown .....
There's a restart that is not software related.
View 3 Replies
View Related
Jun 14, 2010
I am having trouble with my home network, from one computer to another both using wireless g (Ubuntu 10.04) what transfer rate should I expect/hope for when copying a file from one computer to another? My speed is consistently 220 KBps am I correct in assuming this is pretty bad?
View 1 Replies
View Related
Feb 24, 2010
When i try to copy files from my samba server (Ubuntu 9.10) to my windows seven media center, the speed is extremely slow. So slow that is better to download 100mb file from the internet, than from my lan. And on my lan, every card and switch is at 1000 mbps speeds on cat5 cables. And from XP or other linux machine
View 1 Replies
View Related
May 13, 2010
I recently got karoo broadband installed, the speed is normally 8mbps but the longer I am connected to my router the slower it gets, I have to disconnect and reconnect to the router to get back to full speed, is this due to a bad wireless driver or do I need new drivers or a better router.
View 2 Replies
View Related
Mar 28, 2011
How do you set wireless speed in natty? I've tried
Code:
sudo iwconfig wlan0 rate 54M
but nothing happens. I've tried this with wireless enabled and disabled (using network-manager), with and without the module loaded (ath9k) and using the solution provided in some forums (adding the command in /etc/rc.local and in a script in /etc/network/if-up.d) but to no avail... link speed always shows up as 65M.
View 4 Replies
View Related
Feb 22, 2011
I have installed Ubuntu 10.10 on my Dell Latitude D830 laptop using the Wubi installer. Everything seems to be working fine except for my wireless connection. When I plug in my wired connection and test on speedtest.net I get download speeds of 20MB/second. However, when I switch to my wireless connection, I barely break 1MB/second. I have an Intel PRO/Wireless 3945ABG wireless adapter. I have scoured this forum, Google, everywhere I can think of to find a solution and none seem to work for me. I love Ubuntu but this might be a deal breaker...
View 3 Replies
View Related
May 4, 2011
Is there a way to increase my internet speed in ubuntu 10.10 with a wireless conection
View 1 Replies
View Related
Mar 1, 2010
I have the following nasty issue:I am using fedora 12 and I use vpn for working remote.When I browse the internet the speed is very slow!even when I do a yum update it downloads the packages with max 100kb. if I drop the vpn connection I download the packages with 1Mbdo you know what the problem could be? i created the vpn connection using the network manager...it is a regular pptp connection for the vpn!
View 14 Replies
View Related
Sep 12, 2010
I am connecting from this Ubuntu 9.10 computer to a WRT54G running dd-wrt, over WPA2 AES. Normally, everything works fine and I get very satisfactory download speeds; usually 1.5+ Mbps. Sometimes though, usually after restarting networking a lot, i.e. /etc/init.d/networking restart, the download speed seems to be limited to around 64-70 kbps. It also happened recently when I disconnected from a vpn with vpnc. It's really strange because it has nothing to do with changing any settings.
The only things I can think of are POSSIBLY wpa_supplicant causing problems because that's the only thing besides networking that's restarted. It could be related to my router config but I can't imagine what because it runs so fast normally. Rebooting the router doesn't fix it. Restarting the network, manually killing wpa_supplicant, rebooting the router. None of these seem to fix it. The only way I've found is to just reboot. Obviously, something breaks at some point that isn't affected again by anything but a reboot.
View 2 Replies
View Related
Jun 15, 2010
My wireless is flakey -- dropped connections, poor speed, etc. As diagnosis, I loaded the 'wavemon' utility so that I might watch the radio and signal and noise.Things will be good, then fall off, then get better, then go away entirely. Repeat continuously and randomly. For these experiments, my laptops -- more than one -- are on a table.The table is roughly 15-20 ft laterally from the access point. The access point is also 8 ft above the floor vs. 3 ft table height.(grin) While the signal "wobbles" everything else is mechanically stable and otherwise not moving.
View 11 Replies
View Related
Jun 7, 2011
as per pytheas22, i'm attaching few details here. my download speed would starts at 470 kB/s and gradually decreases until it reaches 116 kB/s. Loading web pages seems to be fine.
[Code]...
View 5 Replies
View Related
Sep 19, 2011
I have a pretty decent DSL connection that usually gave me about 105KB/second download speed over wifi. The "official" download speed was 1.5 megabits so I should have been getting a bit more, but that's not my question.
I recently switched to Mint from Ubuntu. Now my download speed is significantly slower, to the tune of 45 KB/second. Since the connection runs at normal speed when I connect via an ethernet cable, my guess is that mint doesn't give enough power to the wifi card. Is there any way I can fix that?
View 2 Replies
View Related
May 20, 2010
I am running Ubuntu 10.04 from a USB key (16GB). Overall I'm pretty fine with it but there are a few problems I am having. It seems to be very slow. In particular, Firefox and Pidgin freeze every now and then, before becoming active again. The same thing also happens for other applications such as Rhythmbox, Gedit, and the terminal. Additionally my start up and shut down times are horrible (worse than when I use Vista and Ubuntu 8.04). I was wondering if there is something with my install or if this is all due to the fact that I am running from a USB. I don't think it's the USB since I ran 8.04 from a USB HDD (55GB) and didn't have any problems with speed.
View 4 Replies
View Related
