I am struggling with a problem with the volume control... when i try to adjust the volume with the sliding bar i can not do it. If i put the scrollbar to the 0 position, it is muted. when i move it to anywhere else, i get the full volume. From other programs like vlc, i can adjust the volume with no problem.
View 2 RepliesI'm running Kubuntu 10.10 32 bit on an old DFI KT600AL motherboard based system using the onboard VIA 3058 AC97 audio (because it supports front panel audio connections and none of the add-in PCI soundcards I have do). I have an old Gateway/STB TVPCI TV tuner card (mainly wanted the FM radio part to work) hooked up to the cd audio connector on the motherboard because the digital audio over the pci bus apparently isn't supported for this card (neither is the onboard analog mixer on the tv tuner card, I had to hack a CD-ROM audio cable and solder it to the audio outputs of the tv tuner module on the TV tuner card). When I use the master channel as the master channel (selected in Kmix) then as one would expect it affects the output volume of all other audio playing on the system except that which is being handled by the PCM channel. On Windows the PCM channel was also affected by the "Volume Control" slider such that ALL volume levels were reduced when moving the slider. I'm hoping someone can help me figure out how to make it work like this on Kubuntu.
First off I should warn you that I (like many users of older hardware that is not properly supported under PulseAudio) have uninstalled PulseAudio (because it's garbage) and am using Alsa to manage my audio hardware. I would think that there would be some way to do this using the 'amixer' application to add the PCM channel as a component of the 'Master' channel so that when the volume is turned down using the 'Master' channel control it will affect the PCM channel too (at least the output to the speaker jack, not necessarily the capture or mix volume though), but I'm not really any good at doing things from a terminal window and the options for the amixer command kind of confused me.
since using 10.04 I have a big problem with my usb headset (freetalk everyman)
1. Problem: I cannot regulate the volume of the phones (output) anymore with gnome-volume-control. By default the volume is set to 100% which is way too loud. When I set it under 100% there is no sound at all. Values over 100% work.
2. Problem: The X server is freezing iregulary when I connect the headset and disconnect it, Magic SysRq works. I checked Xorg.0.log and found out that it recognizes the usb headset as keyboard:
[Code]...
My volume control seems to have only three settings: TOO LOUD, VERY QUIET, OFF. If I adjust the Master volume slider from the Panel, only about the right 1/8th has any effect and if I slide it past about the 95% mark, I get no sound at all. At the far-right end of the volume control, I get total volume. It's basically like the slider only has any impact in the top 5% of it's space. Below 95% of the slide, there is zero volume.
It's so drastic, that one tap down of the volume button on my keyboard kills the sound (because it nudges the slider past that 95% mark). This happens in the Audio settings, etc., system-wide. If I adjust the volume for an individual app from within the app (MPlayer, for example) it behaves exactly as expected (that is, app volume works smoothly, it's just master volume that has this issue). I have run through most of the "obvious" things-- I'm wondering if I broke something by installing the extra KDE packages to get Amarok to work.
I'm running f13 on eeeeeeepc netbook .... gnome and compiz The <FN> keys that control volume are not working, but brightness, for example, works fine. The keyboard settings in gnome do not seem to allow me to set the volume to the <fn> key combos.
View 2 Replies View RelatedVolume up, volume down and mute keys on the keyboard don't control the volume any longer.They worked before. Hitting the keys brings up a progress bar widget with the volume level unchangeable, set at 0% (which is not accurate at all).It looks like the key mappings or key bindings are working, but there is a disconnect with actual functionality. The volume cannot be changed or muted anymore from the keyboard.
This worked just fine in KDE on Fedora 11 before upgrading KDE components yesterday with Yumex. I am now using KDE 4.3.2 I don't think that it's a coincidence that it stopped working after doing an update.
I updated the kernel and nVidia drivers too, but this problem exists when I went back and tested with the previous kernel, so I don't suspect the kernel upgrade. No info in Xorg.conf about the keyboard. Is there a setting that I am missing?
Sound works just fine. I can listen to whatever source I like. This is not a problem with the sound drivers as far as I can tell.I just want to be able to control the volume with the keys on my Logitech Illuminated Keyboard, model Y-UY95. Is anyone else experiencing this?I can adjust the volume with Kmix 3.5 or GNOME Volume Control V2.1
Is there a way to default volume to 100% in the terminal with gnome-volume-control-applet or any other program? I am setting up a dedicated Zsnes machine which boots into Fluxbox but the volume is muted by default. There isn't a man page for gnome-volume-control-applet.
When I log into Gnome the volume is set to 100%, but Fluxbox is always set to mute.
I'm using 10.04 now and it runs ok, except one strange thing in the Volume control applet. Sometimes, when I click on the volume slider, it moves up. Even if I try to slide it down, it moves up on every click. The same when I click left of it - it keeps moving up! This is very annoying at night when the music gets loud and wakes everybody. It happens with or without Compiz turned on
View 3 Replies View RelatedRight now, it controls both Master and PCM, resulting in weird volume increments. I want PCM to stay at 50 and only change Master with my volume keys.
View 3 Replies View RelatedI recently purchased an external USB audio card [URL] All worked fine except the volume that comes out is BLASTING, and changing the master volume does nothing. Individual applications let me change their volume, but this is extremely anoying and often leads to me accidently blasting the room.
View 9 Replies View RelatedI upgraded from 9.10 to 10.04 and my volume control disappeared from the panel. I have reinstalled pulseaudio but it had not re-appeared. I can't find it in the Add Panel list nor can I find it in the Pulseaudio volume control application as an option.
View 5 Replies View Relatedi get this error brand new lynx installation when i try gnome-volume-control from the command line,
i get this error
Code:
** (gnome-volume-control:20731): WARNING **: Connection failed, reconnecting...
** (gnome-volume-control:20731): WARNING **: Connection failed, reconnecting...
** (gnome-volume-control:20731): WARNING **: Connection failed, reconnecting...
what could be the problem?
I've just upgraded to kUbuntu 10.04. I've been using Gnome for a few years now, and felt the need to try KDE again. I've managed to get my NVidia 8200 with HDMI audio working, but have one last annoying issue.
I can't control volume with my RF remote or keyboard.
More to the point, the keys control the sliders in kMix, but to no effect on the sound. This is likely because I need to use Pulseaudio to get my HDMI working. The sliders in Pulse volume control, control the volume nicely. Either I need a way to force kmix to talk to pulse, or a way to re-map these keys to control pulse.
how to set at least my headphone/lineout socket precisely to -15dB at boot up? If I knew how to make amixer commands permanent, I wouldn't be re-raising the issue
The Gnome GUI volume control is fine in normal circumstances but to set it accurately requires a bit too much fiddling, IMO - now if someone were to adjust the programming so a dB readout accompanies slider movement, rather than as a pop-up after adjusting the slider, 'twould be more ergonomic, IMO.
Tvtime built in volume control stopped working in maverick because it depends on kernel support of Open Sound System (oss) and ubuntu kernels are no longer compiled with this turned on.
You can get an experimental deb of tvtime for maverick here:[URL]
which will work with ALSA sound system.
Here is a partial solution I found on the Russian Ubuntu board by Alexandris if you cannot get the above deb to work for you:
tvtime configuration file at /etc/tvtime/tvtime.xml will allow you to reassign the left and right arrow keys to control whole system volume level while tvtime is running.
Make the following changes in tvtime.xml:
1. comment out existing left and right keybindings by enclosingg them with '<!--', '-->' tags:
Code:
<!--
<bind command="left">
<keyboard key="left"/>
<keyboard key="-"/>
[Code]....
3. save changes to tvtime.xml and start tvtime in a terminal window and see if there is any error messages. The Russian Ubuntu board recommended using "amixer -c default" , but I had to change mine to "amixer -c 0" (the number of my sound card) to get things to work. You might have to do the same...
I normally run KDE, but installed GNOME as well on my netbook (running openSUSE 11.2) to try out. However, I noticed there is no longer any volume control applet. The GNOME panel control is labeled 'deprecated', and the volue Fn keys, which work fine in KDE, do not work at all. I tried launching the PulseAudio Volume Control app, but it gives me a "Connection Failed: Connection Refused error". I still have sound, and I can adjust the volumes in alsamixer, but is rather inconvinient. What is the "right way" to adjust volumes in 11.2's GNOME?
View 9 Replies View RelatedNot sure how/when/why it happened the volume control app on my control panel is missing. I tried adding it by doing a "Add to Panel" but the volume control app says it is now deprecated.Is there any other way to change the volume quickly instead of having
to open pulseaudio volume control
Is there any way, native or within download, of changing audio volume on a per-application basis? I vaguely remember doing this in the vista basic that was installed on this when I got it a couple of years ago, but was removed after a couple of months due to instability. I'd like music streaming thru VLC louder relative to games being played thru Adobe Flash in Chrome (which are at 100% of possible, 100% of the time, no options other than mute).
View 5 Replies View RelatedI've got my xubuntu 10.10 install just about perfect on a little acer aspire d250, apart from a small sound useability issue: In the interests of simplicity and resource usage I removed pulseaudio. After a bit of fiddling I got it so that my USB soundcard (ProDac) is recognized and automatically set as the default soundcard when plugged in. Any sound applications automatically use the USB sound if it present, no need to around with pulse. The only problem is that my netbook's volume control keys still only control the master volume of the inbuilt soundcard, and have no effect on the usb sound. Does anyone know of a way to change which sound device these keys actually effect? I'd like to write a little script so that when the usb device is detected the keys are remapped.
View 1 Replies View RelatedI used Ubuntu 10.10 (64 bit) on IMac i7. As far as, I remember, after installing Pulse-Audio Equalizer, for each restart of the system, after login screen, system sets volume to maximum value. What can I do?
View 1 Replies View RelatedI think this is a bit of a complicated problem so bear with me while I explain it. I'm using an HP Laptop with Ubuntu 10.10. The laptop has the touch buttons for mute and volume up/down, and I use them all the time (at least when I was on Windows). I've very recently switched to Ubuntu and now those keys are causing problems with a game called Minecraft. Basically, when I'm playing it and use those keys, it brings me out of full screen (if I'm using fullscreen) and then seems to mute like it should, but the problem is, it doesn't UNmute when I press it again. The lighted button on the laptop goes back to showing its unmuted, but the game still has no sound. I've tried messing with the sound settings inside the game, and doing all these weird combos of when I mute/unmute and all, nothing seems to help. I usually have to restart the computer to fix it, but then if I use the button again, it does the same thing.
P.S. does anyone know of a way for these buttons to NOT interrupt full screen? I had the same problem with it interrupting fullscreen apps on windows, but then I used a program called 3RVX and it fixed it. Is there anything like this on linux?
The volume on my computer randomly mutes/unmutes itself rapidly at unpredictable intervals. sometimes it works fine, other times it does not. I cannot find out what the problem is. I have never had this problem until recently, and this problem has surfaced in ubuntu 10.10, 10.04, 64 and 32 bit versions of the operating systems. I have used this hardware setup for a year before this problem ever surfaced. My hardware is installed and working fine, I just cannot figure out why this is happening. Does anyone know of some commands I can use to find out what is causing the volume to mute/unmute itself?
View 1 Replies View RelatedMy internal mic on sony vaio was not working on karmic 64bit. After I followed these instructions [URL] (updated alsa to 1.0.22) I got the microphone working, but now mplayer does not play any sound (although it plays files), as it tries to use pulse by default. However when run with -ao alsa, it works fine.
Other than that, the volume control has not effect on the sound, so every time I need to control it using alsamix.
When I remove pulseaudio, everything seems to be working, except gnome-volume-control and gnome-volume-control-applet do not start, and the keyboard volume controls dont work.
Here are the sound cards I have:
Code:
progre55@progre55:~$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: ALC262 Analog [ALC262 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
[Code]....
I installed Lynx 10.04 from scratch and found the audio volume control is missing from the launch panel.
View 9 Replies View RelatedAlright, at first, the volume control went missing from the indicator applet, but then re-adding it to the panel didn't do anything but add a mail/chat applet. So I tried to reset the indicator applet settings with this code...
And now all that happens when I add the indicator applet to the panel is that the text: "No indicators" pops up where the mail/chat applet was before. Is there a way to get the volume applet back into the panel?
I've just removed PulseAudio and installed Envy24Control in order to make sound working with my M-Audio Delta 1010LT, it's working fine now, but the only problem is that the master volume control disappeared, and the buttons on my keyboard (volume + and volume -) are not working (with PulseAudio they were fine). Using Ubuntu 10.10
View 3 Replies View RelatedI am annoyed with the pop up of volume control notification on GUI of my Ubuntu 10.10 ,The volume slide bar moves automatically.Its flickering on my screen and hinders my work.I wonder why ,I am new to Ubuntu ,how to put off this notification I tried
sudo mv /usr/share/dbus-1/services/org.freedesktop.Notifications.service /usr/share/dbus-1/services/org.freedesktop.Notifications.service.disabled
but the notification icon is gone but a small volume control frame appeared from now-where giving the same frustration.( I have installed Ubuntu10.10 on HP Pavilion dv5-1015nr laptop un-installing the preloaded windows)
i recently did a clean install of 10.10 to an old box i had so i could mess around with it and learn. however, all audio (and videos too) would stutter and play very quickly (a 1 minute videos video would play in about 45 seconds). so i followed the solution found here: [url]
this fixed the playback problems perfectly, however, i lost the volume control applet in the upper-right of the screen. reinstalling to volume control and then adding the "indicator applet" back to the panel adds a non-functional volume control icon and an additional mail icon.
I'm having a problem with Pulseaudio for quite some time, I already made some topics about it. But still no solution. The thing is, I can't use my keyboard volume control, it's only manipulating my ALSA configuration. Not my main Pulseaudio volume. Here is some information about my sound card:
$ pacmd list-cards
Welcome to PulseAudio! Use "help" for usage information.
>>> 3 card(s) available.
index: 0
name: <alsa_card.pci-0000_00_1b.0>
driver: <module-alsa-card.c>
owner module: 4
[Code].....
I own an ASUS G71V laptop and I run openSUSE 11.2 with latest kernel and patches.
I just tried to use Fn+F10/F11/F12 combinations to regulate volume, just to see if they work.
I found that (from KDE 4.4.3) I can see the pop-up volume indicator going up and down as I press the right combination.
Ok... unfortunately, hardware keys regulate the wrong volume slider as I can see by opening Kmix. The front-microphone channel instead of master is regulated.
Actually, I just found that if I click on the volume icon on the taskbar I get the front mic slider, which seems to be bad.
How can I tell KDE that the default channel is the "master"?