Ubuntu Installation :: No Operating Systems Found On Dual Boot Install
Aug 23, 2010
I currently have Windows 7 installed. I wish to dual boot this with Ubuntu 10.4. On a 120gb drive I allocated a large percentage to Windows and have put two partitions on the end; 1gb for swap, 15gb for Ubuntu. However, when I go to install and get to the partition manager bit it claims no operating systems have been found. Contrary to this, when I boot into the live CD it sees all the partitions, however these cannot be accessed and no error messages are displayed (However, accessing the Windows partition appeared to corrupt the install and I had to format...). When running install from the live environment the same no operating systems found error occurs. Windows 7 works fine and the drive is IDE (if this makes any difference).
View 2 Replies
ADVERTISEMENT
May 11, 2010
I am preparing to do a fresh install of lucid lynx dual boot with vist@ Currently I am running 9.04 in this configuration. The install guide for Lucid says the new grub2 doesn't support more than 2 operating systems. plus I apparently can't edit it either. Besides vist@ there is a hp recovery partition which has a seperate entry in my existing grub. Does this mean I can't use the lucid desktop disk for a fresh install because I would have 3 operating systems? Lynx, vist@ and HP recovery partition.
I only have two applications left I am using on vist@, but I have no recovery disk, only an old image for my vist@. I am very concerned about this upgrade. 5.04 went smooth and each one since then has been a bit harder. I could not get 9.10 to run and had to go back to 9.04. I hope I am not at the end of the road. How about using grub instead of grub2?
View 9 Replies
View Related
Jul 16, 2011
I'm trying to dual boot Ubuntu and Win7, and I just did a clean install of Win7. However, when I start the Ubuntu installation it merely just says no operating systems detected and my only option is to erase the whole disk. I can see the NTFS partition in disk utility but can't see anything in GParted.
I've tried to look through the forums but can't seem to find a solution to this exact problem - does anyone point me in the right direction or to the solution?
View 2 Replies
View Related
Jul 26, 2010
I have no clue how Linux works and I haven't had much experience installing/dual booting operating systems. Most of my knowledge in computers comes from fixing errors with crappy hardware or Windows. Now I want to learn how to use a computer instead of how to fix it. Hence, I want to have Windows & Linux on my computer. My laptop(Acer Aspire 4530) has two hard drives, one is Vista and the other was empty(until I filled it with stuff). What is the simplest method to install Linux (or any of its variations) on this computer? Do I just install/partition all of Drive B to Linux and leave Drive A for Vista?
View 3 Replies
View Related
Apr 24, 2011
I just installed ubuntu on 60GB of unallocated space on my second drive and am now receiving a Goem error. Before, I was dual booting with two Windows 7 installations, using the second drive to store data and the second Windows 7 installation. I cannot boot into any of the operating systems.
View 1 Replies
View Related
Apr 4, 2011
Sorry for the hard to understand title but it's difficult to describe in one sentence. What I'd like to do is install Windows and several different versions of Linux on the same system. After everything is installed, I'd like to switch between operating systems *from inside the operation systems*.
Example: I'm inside Windows but I want to reboot into Ubuntu 9.04. I need to run a command to update the boot manager so it knows to boot into Ubuntu 9.04.
I do not want to walk to the physical box to make a menu selection. EDIT: I'd like to be able to switch between Windows 7 and Ubuntu (9.04, 10.04, and 10.10)
View 6 Replies
View Related
Nov 4, 2010
I am attempting to install Ubuntu via a USB stick. I have Ubuntu on the USB, I have booted from the stick and I have made it to the installing window. My problem is, I do not get the option to install next to other operating systems, which is what I want.If I have not been clear enough then please let me know and I'll see what I can do.
View 6 Replies
View Related
May 18, 2009
I presently have Ubuntu and Windows XP Pro installed. By using the GRUB loader I can choose which to load.
I would like to install Fedora as a third option, but do not know how this will affect the GRUB and the choices.
View 2 Replies
View Related
Jan 6, 2010
I am currently using ubuntu 9.04 and I am planning to have a dual boot my system with fedora 12. My computer is quite old and I have RAM of 256 MB DIMM 266 MHZ with pentium 4 processor. So will the dual operating systems work in my computer??
View 2 Replies
View Related
Mar 13, 2009
I am unable to Install Fedora10 in my system as one of the multiple operating systems and it gets hanged after probing for Hardware devices and so ...I get fedora trademark sought of symbol and even after waiting any amount of time it doesnt go further..neither the keyboard works nor the mouse pointer moves... I am stuck at this screen shown in the installation screenshot...I get this screen however I dont get the options back or next or its that I am unable to see this options on the screen at all and mouse gets hanged and even keyboard doesnt work...
[code]....
Initially after booting with the media it doesnt even prompt me to press any key to boot from CD or Dvd or I get any screen to select the option for the mode of installation like text based installation or graphical installation..it hardly shows me this screen for even a fraction of second as well...
It takes me to the screen
1) Install or upgrade fedora
2) rescue existing installation...
3)
4) Memory test
when I click on install fedora I am taken to the fedora splash screen and nothing goes ahead... I tried in rescue mode as well... In rescue mode it asks me for language selection...keyboard layout... later it doesnt go ahead as well... I have checked the installation media and it confirmed that the installation media is good... I use Redhat 4.1 version and It works fine except for the message drivers/usb/hid.c core message received at :75 while trying to restart shutdown or access a virtual console... Along with Redhat and while trying to install fedora I have windows server 2008,Windows vista on that harddisk...
View 4 Replies
View Related
Aug 12, 2011
I have Windows 7 working on my laptop. I have 20GB space unpartitioned. I want to install a flavor of Linux like Fedora or Ubuntu in that space, but I have heard that keeping a dual OS configuration sometimes results in losing data stored on the hard disk. I've also heard that it may sometimes cause unrecoverable problem because when Linux is loaded on hard disk it will take over the boot loader from Windows.
Is this correct? Moreover, I have 6 partitions in Windows, but if I use a Live CD for Ubuntu or Fedora to boot, then it is not showing some partitions -- sometimes it shows only 4 or 5 partitions. What might be the problem, and how to resolve it without formatting the whole hard disk and repartitioning it?
View 1 Replies
View Related
Feb 7, 2010
I have Ubuntu and Windows on the same machine. If I install Thunderbird on both operating systems is it possible that both installs can access the same email files so that all of my emails will be in one file no matter which operating system was running when emails are downloaded or sent?
View 6 Replies
View Related
Jan 24, 2010
I have winxp and win 7.I want to install fedora core 12.I tried but I could not install.How can I install fedora core 12 with winxp and win 7.
View 3 Replies
View Related
Jun 7, 2011
I've decided to move to Debian because I have noticed Ubuntu releases getting progressively more unstable.I am following the official Debian installation guide. Just did this with the Debian 6.0 Net install .iso: 4.3.1. Preparing a USB stick using a hybrid CD or DVD image. Debian CD and DVD images can now be written directly a USB stick, which is a very easy way to make a bootable USB stick. Simply choose a CD or DVD image that will fit on your USB stick. See Section 4.1,Official Debian GNU/Linux CD-ROM Sets to get a CD or DVD image.
Alternatively, for very small USB sticks, only a few megabytes in size, you can download the mini.iso image from the netboot directory (at the location mentioned in Section 4.2.1,Where to Find Installation Image).The CD or DVD image you choose should be written directly to the USB stick, overwriting its current contents.
View 5 Replies
View Related
Aug 3, 2010
I'm trying to install Ubuntu 10.04 (32 bit)on my laptop (where currently is installed the amd64 version of Ubuntu 10.04 that I've decided to remove because of some small issues).I've tried using the installation CD (the same I've used to install it on my desktop, so I know that is a working copy),but at boot, although I select to boot from CD, the Live version doesn't start and Ubuntu 64 is run as usual.I've tried to create a startup diskon a usb pen,there the live version seems to start but then Busybox 1.3 is loaded and there is an error with initfrm saying that no operating system can be found.I've been told to download the alternate edition, but I'm still downloading it,
View 3 Replies
View Related
Apr 26, 2010
I just downloaded the program, reviewed it using the cd, and I like it very much.I have Windows XP and Unbuntu 9.04 installed.I know that 10.04 uses GRUB II.If I install Ubuntu 10.04 RC in a partition, will I still be able to load the other two operating systems?
View 2 Replies
View Related
May 8, 2010
I have been reading around the internet but I cant find any solutions, and on a side note im new to linux.When I try to install ubuntu 10.04 on my dell xps 420 desktop it doesn't detect my windows 7 install, would this have anything to do with me having my RAID set to on? and if I do change my RAID settings will I damage my windows 7 installation?here is my sudo fdisk -l:
Code:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
[code]...
View 5 Replies
View Related
Jan 30, 2015
I'm trying to install debian and when the installer starts it UEFI at the top, instlal completes however on reboot it says 'no operating system found' i've read it can be because of UEFI but I have tried different bios options but to no avail.
Bios options
Sata mode: AHCI/IDE (haven't tried IDE yet)
Tried various combinations of the below
CSM: enable/disable
Boot Priority: Auto/legancy first/uefi first
Quick Boot: enable/disable
Boot up Num-lock Status: on/off
View 14 Replies
View Related
Sep 13, 2011
I'm using - Ubuntu and openSUSE. I've looked on the Internet for how to install software on these operating systems, but I can't seem to understand the terms used, such as:
Repository
Package
Source code
View 2 Replies
View Related
Nov 22, 2010
I installed Fedora 14 in a dual boot with Windows 7 (Win 7 came preinstalled on my Vaio, I freed up 30 GB on a hard disk drive and installed Fedora in it).The first reboot took me straight to Windows. I could not find a way to get multiple Operating systems, so I tried looking on the net a bit, and installed EasyBCD. This gave me the option of choosing the boot up OS. But when I choose Fedora in the options, the screen changes to GRUB4DOS which lists Fedora and Other as my two boot options.Selecting either one of these options results in Error 22 No partition found.
View 4 Replies
View Related
May 2, 2010
I was wondering how to prevent grub2 from detecting operating systems on other hard drives. I have Ubuntu Lucid on the second hard drive with windows 7 on the primary (unplugged for now).
View 2 Replies
View Related
Jan 17, 2010
But when I install new updates for Ubuntu and restart my computer to apply those updates.... a new Ubuntu with different number appears on the list of the operating systems that I need to choose from
[Code]...
does this mean every time I updated Ubuntu I'll have additional OS on my device?
View 3 Replies
View Related
Jan 22, 2010
I was wondering if I could make logical / partitions if I have a primary /boot partition. Is this a potential way to get around having only 4 bootable operating systems on a single HD?
View 3 Replies
View Related
Jan 31, 2010
i dont know if this is the right section for this but i installed linux after i installed windows server 2003 and some how the grub loader got messed up and wouldnt show, only windows would boot. i fixed the grub loader through my live disc and when i select Other operating systems i get Error 11: Unrecognized device string. here is my fdisk -l.
Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x2c8e2c8d
Device Boot Start End Blocks Id System /dev/sda1 * 1 6 48163+ 7 HPFS/NTFS /dev/sda2 7 34329 275699497+ 7 HPFS/NTFS /dev/sda3 34330 38227 31310685 83 Linux /dev/sda4 38228 38913 5510295 db CP/M / CTOS / ...
Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x99b707d2
Device Boot Start End Blocks Id System /dev/sdb1 1 38912 312560608+ 7 HPFS/NTFS
Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000080
Device Boot Start End Blocks Id System /dev/sdc1 1 6 48163+ de Dell Utility /dev/sdc2 7 38227 307010182+ 7 HPFS/NTFS /dev/sdc3 38228 38913 5510295 db CP/M / CTOS / ...
and here is my menu.lst
[Code]......
View 2 Replies
View Related
Jul 18, 2011
I have a Sony Vaio laptop and the hard drive died in it. I replaced the hard drive and I am now trying to install Ubuntu. My problem is that when I set it to boot from CD it tells me that "No Operating System Found".
So how can I fix this issue and get Ubuntu installed?
View 5 Replies
View Related
Jan 30, 2010
i dont know if this is the right section for this but i installed linux after i installed windows server 2003 and some how the grub loader got messed up and wouldnt show, only windows would boot. i fixed the grub loader through my live disc and when i select Other operating systems i get Error 11: Unrecognized device string. here is my fdisk -l.
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x2c8e2c8d
Device Boot Start End Blocks Id System
/dev/sda1 * 1 6 48163+ 7 HPFS/NTFS
/dev/sda2 7 34329 275699497+ 7 HPFS/NTFS
[Code].....
View 2 Replies
View Related
Oct 22, 2010
Recently I've installed Open Suse 11.3 along with Ubuntu 9.10 on my PC ( made it a dual-boot OS ). This morning while logged in, in Open Suse 11.3, found out that there were important update for kernel in Yast. So, did the update and then required to restart the PC. In the Grub/boot menu, I chose to log-in to Open Suse 11.3, but after a while it returned with " Error 15, file not found ". Luckily I was able to log-in in Ubuntu 9.10. Assumed that Error 15 is always related to misplaced or wrong configuration of Grub in the partition, I did several searching via Google, and found this possible solution HowTo Boot into openSUSE when it won't Boot from the Grub Code on the Hard Drive . So I tried the " Broken Grub menu: boot to the menu, drop to a console and boot openSUSE direct " method. But rightly after the " find /boot/grub/menu.lst " command as instructed in the solution, it returned with ( hd0,0 ) and ( hd0,4 ). Why there are 2 bootloader in the Grub ? Which bootloader should I choose ? And for convenience, here is my " menu.lst " folder that I get via Terminal in Ubuntu 9.10 :
$ cat /boot/grub/menu.lst
# menu.lst - See: grub(8), info grub, update-grub(8)
# grub-install(8), grub-floppy(8),
[code]....
View 9 Replies
View Related
Sep 26, 2010
I have installed an external drive on my Windows 7 PC and therefore feel able to try to set up a dual boot with another operating system, and Ubuntu is the obvious first choice: however on the Ubuntu site the only options avaiable seem to be to install to a stick or on a new partition on the Windows C: drive. I couldn't really fathom installing to a stick and nothing seemed to run off the DVD to which I wrote the .iso file. I most definitely do not want to alter the C drive.
Seems to me it would be a good idea to have the option to install to any drive partition of one's choice. My son-in-law who uses Linux a lot in work suggested a web site explaining how to install Linux on an external drive, but that entails opening the PC and disconnecting the C drive. I assume that is because otherwise I would lose the Windows installation. My interest in PCs is most definitely directed towards systems and software, not hardware so I don't trust myself poking aound inside.There is presumably an explanation of why there is no simple way to ty out Ubuntu etc. but I can not find any explanations and would be grateful for a pointer about where I should look.
View 4 Replies
View Related
Mar 14, 2011
I have a dual boot laptop with OpenSUSE and Ubuntu. The boot loader used is Ubuntus Grub that came with the Ubuntu installation.
I have done a zypper dup and upgraded to OpenSUSE 11.4. When I reboot my system I can no longer boot into OpenSUSE, Grub says something about a missing kernel.
I think I understand whats wrong here; the OpenSUSE entry in Grubs table hasn't been updated with the changes brought in by the zypper dup (new kernel i guess).
I'm I correct to assume this? How do I fix the problem? Booting into Ubuntu I tried to find /boot/grub/menu.lst to examine it by I cannot find it. I know Ubuntu use a newer version of Grub, does it have a different file layout?
View 1 Replies
View Related
Aug 30, 2010
I recently installed Ubuntu Netbook Remix (10.04) on my brother's Acer Aspire One (751h) netbook, set up to dual boot with XP Professional. The initial install was successful, with both OS's booting correctly. However, after a series of updates and module builds (this machine has the Poulsbo chipset, still somewhat of a mess), Grub2 is now unable to boot XP, displaying the error "Operating system not found."
To be clear, grub works properly (aside from not booting XP), so the MBR is intact, although I've rerun grub-install to be safe. Restoring the windows MBR (using testdisk) boots XP happily, but of course ignores the ubuntu installation. I also had testdisk rebuild the NTFS boot sector, to no change - grub still doesn't work, the windows MBR does. Using the grub console, I can "root (hd0,1)" and see files on the XP partition, but "chainloader +1; boot" again fails with the same error. The ubuntu install can likewise mount the NTFS partition with no problems.
Given the fact that switching the MBR fixes the issue, I'm suspecting a Grub2 configuration problem. However, the simplicity of "root (hd0,1); chainloader +1; boot" leaves me stumped as to what that could be. Also, the error text "Operating system not found" is suspiciously identical to my BIOS's error message when attempting to boot from a non-bootable medium (as I found out while attempting to make a bootable usb stick with my mac).
View 1 Replies
View Related
