I have recently installed 10.04 on my Fujitsu E8210 laptop and now have a problem with the flickering and noisy screen. I have narrowed down the issue to my ATI mobility Radeon x1400 drivers and seen a suggestion to install Gallium3D drivers. Up 'till now I have installed new kernel from [url].
And now am looking for directions on how to install Gallium3D drivers for my video card.
who has installed these drivers on ubuntu will help me to install ? Because I can not coped...
ati mobility radeon x1400 driver
need me 32bit driver... I found only 64 ...
installing ATI Mobility Radeon x1400 driver on 9.10?
View 9 Replies View RelatedI'm having an issue and I'm trying to figure out if the proprietary driver from ATI is actually getting installed correctly or if I'm on the open source driver still. ...and whether or not there's an advantage to one over the other...
I'm on a Sager NP3790 with an ATI Mobility Radeon 9700 graphics card. I've got a fresh install of Ubuntu 10.10 and the basic 2d functions all seem fine, but any games I try to run with OpenGL simplt fail and "glxinfo" yields:
Error: couldn't find RGB GLX visual or fbconfig
lspci -k yields:
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
Subsystem: CLEVO/KAPOK Computer Device 0471
Kernel driver in use: radeon
Kernel modules: radeon, radeonfb
I have downloaded the latest legacy driver from ATI (ati-driver-installer-9-3-x86.x86_64.run) and I've not had any success running that directly. It appears to not knowingly support anything newer than Ubuntu 9.04. I have tried forcing that driver to build itself targeting 9.04 and I've tried installing the .deb packages that it produces, but with no luck there either.
If I recall this laptop's former lives, it has in the past run Eternal Lands without issue back when it was Ubuntu 8.x, but somewhere between a client update from them, some update from ATI or Ubuntu I seem to have lost my OpenGL capabilities.
I have been using slackware for a few years now and just made a jump from 12.1 to 13.0 recently on my Dell Inspiron 6400 laptop. Everything seems to be working great except for the video players. When I try to start xine I get the following error:
X Error of failed request: BadAlloc (insufficient resources for operation)
Major opcode of failed request: 135 (XVideo)
Minor opcode of failed request: 19 ()
Serial number of failed request: 1977
[Code].....
I would like to use my S-video connection on my ATI Mobility Radeon x1400 Laptop but I don't know how to do it. Could someone help please? I have never tried to use it before so I cannot tell whether it worked with previous versions.
I am using Natty.
Here is what I get with the command xrand. code...
1- I'm trying to install the ATI Mobility Radeon HD 5470 driver over the non-free repository ...the problem is that until now i didn't found a recent documentation ...and to be honest i don't know which procedure should i use to rightly install the driver .
2- I have two graphic cards (integrated Intel with the i5 processor), and i can't change the default one to the ati! because debian had set the intel card as a native one...! that's why i´ m wondering if just an installation of the non-free drivers will solve this or not! I think every body will ask me how the lspci output looks like so here is it : 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
[Code]...
When I put my laptop, a Presario X1000 to sleep that uses Radeon Mobility M7 LW [Radeon Mobility 7500], when it comes back up, I get just black and white "nosie" on the screen.
Even after I do cntr+alt+F1 and then cntrl+alt+F7 it still doesn't appear to restore the regular screen.
I have a problem with my graphic card. My desktop effects and compiz work fine, but I cant find xorg.conf file (it seems I dont have a driver installed??). I want to play games, but I cant (warsow, and other via wine).. my computer cant start a game.
View 9 Replies View RelatedI'd installed Puppy and was very happy with the performance on my laptop, but I decided to switch to Debian because of the ap-get feature. I decided to go with JWM instead of one of the default desktop environments, but now I'm having to configure everything manually, and I'm pretty lost. So far, I've got X and JWM installed (though no graphical login, and have to startx manually).
Priority one is to update the video driver and get the best performance possible. I have an ATI Mobility Radeon 7500. I know the fglrx driver doesn't work with this card, but I don't know which package to install. When I type "apt-get install radeon", it spits out "E: Couldn't find package radeon"
I'm having some graphics driver trouble on my Lenovo Thinkpad T500. I tried getting the ATI Proprietary driver to work (fglrx) but everytime I boot my X just crashes. Now I'm trying to use the open source driver, but i dont think its working becaues a) It doesn't detect that an external monitor is plugged in (for dual-view) and b) when i run glxinfo i get a "Error of failed request: BadRequest" message.
View 3 Replies View Relatedi'm running Kubuntu 10.04 with KDE4.5 on HP DV5000 and i have problems with the video drivers as usable look where is the problem
LIBGL_DEBUG=verbose glxinfo
name of display: :0.0
libGL: XF86DRIGetClientDriverName: 5.3.0 r300 (screen 0)
libGL: OpenDriver: trying /usr/lib/dri/tls/r300_dri.so
libGL: OpenDriver: trying /usr/lib/dri/r300_dri.so
[code]....
I don't get it on [URL] say R300 is for Radeon 9700PRO/9700/9500PRO/9500/9600TX, FireGL X1/Z1 (2D only) and RS400 is for Radeon XPRESS 200/200M IGP ( What HP DV5000 have ) But in the middle of the info i have OpenGL renderer string: Mesa DRI R300 (RS400 5955) 20090101 x86/MMX+/3DNow!+/SSE2 NO-TCL on lsmod | grep radeon i have
radeon 901424 2
ttm 54611 1 radeon
drm_kms_helper 30726 1 radeon
[code]....
I been searching for months on how to get the s-video to work on my pci VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] card. I found a site with instructions.
This is how I got it to work.
I install Debian 5.0 Lenny Desktop
added the Driver "radeon" to my /etc/X11/xorg.conf file
This work and I was able to use my tv as a monitor however when I try to play a video file from totem or vlc all I could get was audio with no video; These files work and played fine in the CRT monitor.
I've got big problems with ubuntu 11.04 (32 Bit, on Lenovo T500 with ATI Mobility Radeon HD 3650)First of all i have to boot from the installation cd with the option "nomodeset".Also for the first boot from harddisk i have to set this option. After i have installed the proprietary ATI drivers i can boot with the default options but unity won't start....n dmesg i found following messages:Quote:
[ 415.901678] unity_support_t[2357]: segfault at 4 ip b76b2824 sp bfaeee50 error 4 in libGL.so.1.2[b7639000+c9000]
[ 415.905490] unity_support_t[2359]: segfault at 4 ip b75a1824 sp bfd3fa90 error 4 in
[code]....
So Ubuntu had been working great in Lucid, and when I upgraded to Maverick the support for my graphics card stopped. It has the proper driver ("ATI/AMD Proprietary FGLRX graphics driver") active and fglrx, fglrx-amdccle and fglrx-modaliases are all at 2:8.780-0ubuntu2. I also have the xorg radeon package installed. Yet, whenever I try to enable desktop effects (to get compiz to work) it says that Desktop effects could not be enabled.
View 4 Replies View RelatedI have just installed Squeeze on my laptap with a radeon mobility equipped laptop. When it boots, I see the following message:r600_cp: Failed to load firmware "radeon/RV635_pfp.bin".and some others, too, but it stalls at that point, and I cannot use CTRL-ALT-F2 to get a text-based prompt - in fact, I can only seem to get it back with a ALT-SYSRQ (R-E-I-S-V-B) sequence to force a reboot. It is a multi-boot system, with a windows partition, Ubuntu partition, and the new Debian partition. The Ubuntu and Windows partitions will still boot, only the Debian stalls.
When I boot into Ubuntu, I can see the Debian partition, and can see (for instance) the /var/boot/dmesg file, but it only says:"(Nothing has been logged yet.)"So, being new to debian itself (even though, I know, that Ubuntu has a debian base), how can I make it boot without X, which is I presume, the center of the difficulty? Can I change some file on the debian partition using Ubuntu to get the debian partition to boot in text only mode, and then try to fix the radeon driver?
Alternatively, can I put the proper files for the radeon driver *from* the Ubuntu partition *to* the debian partition and expect it to load and boot correctly? I did, at one point, download and install the proprietary ATI driver files on Ubuntu, so can I put them in a proper place on the debian install?
I installed Fedora 11 on my HP Pavillon ze5000 laptop that according to Windows has "ATI Mobility Radeon" video. Words on the screen are not readable because words are moving arouInd on the screen very fast (I think horizontally back and forth by a dozen pixels or so).
View 1 Replies View Relatedknow if it is possible to get an ATI mobility 4 driver for Ubuntu 9.10?
View 1 Replies View RelatedI've got an old computer with an Ati Radeon 9550. I had Ubuntu 10.10 installed and was able to get the gallium driver working but ubuntu seemed to really load down the system so I decided to try Debian so far its running much faster for regular tasks but I'm having a terrible time getting it to recognize the gallium driver. I actually upgraded to sid because I had read that gallium was the default driver for mesa for my card.
Here is what i've done so far.
When I opened package manager it did say libgl1-mesa-dri 7.10.1 (I think that was the right version) was installed but when I checked rendered string it still showed software.
So I went to [url] downloaded 7.10-4 and compiled it according to the directions on the site and installed with make install. I didn't get any errors. Package manager shows its installed but still only software rendering. I tried following the last part of the instructions on this site [url] and exporting the paths but its not working.
Doesn't do anything.
dmesg | grep drm
I have no idea what this error means. Well actually I bet it means my driver isn't loading.
I have an ATI radeon x1300 graphics card on my Toshiba Satellite A100 P542 laptop. I am new to ubuntu. On installation, I was pleased with the mac feel as I use mac at my home. I just cant get the card to work. In the hardware options, my card isn't displayed in proprietary thingy.
I later realised that my graphic driver is no longer supported by ATI and there are no official drivers. So I tried all the alternatives available in Ubuntu software centre. I currently have everything related to ATI, fglrx, xorg etc installed. But seems like all these things are of no use, as my graphics driver still isn't recognized and I cant use Compiz fusion. Leave alone compiz fusion I cannot run good quality videos. The screen gets sluggish when I do that.
So Ubuntu had been working great in Lucid, and when I upgraded to Maverick the support for my graphics card stopped. It has the proper driver ("ATI/AMD Proprietary FGLRX graphics driver") active and fglrx, fglrx-amdccle and fglrx-modaliases are all at 2:8.780-0ubuntu2. I also have the xorg radeon package installed. Yet, whenever I try to enable desktop effects (to get compiz to work) it says that Desktop effects could not be enabled.
View 3 Replies View Relatedi am gonna to buy a new noetbook hp probook 4510s one with ATI Mobility Radeon HD 4330 graphics card is that card compitable with fedora 12 ?
View 10 Replies View RelatedFrom the wiki page I know the ATI Mobility Radeon X1400 card is no longer supported by the new fglrx driver in squeeze. Is there a way to use the older driver from lenny? I'm on the radeon driver and the glxgrears performance is pretty low.
View 2 Replies View RelatedI have ubuntu on a Vaio VGN-A290 with the ATI Mobility Radeon 9600 M10 graphics card. I I installed the Eternal Lands client but it keeps crashing on me. Upon crashing a massage told me that I should make sure the video drivers are up to date. I then went into system --> Administration --> Hardware drivers and it says "no proprietary drivers are in use on this system." So my question is how do I install a driver for the ATI Mobility Radeon 9600 M10?
View 5 Replies View RelatedI just bought a new ASUS laptop with the Mobility Radeon HD 5470 card.It seems like there's no driver for it yet (the amd.com download wizard is a dead end because I only find the HD 4000 series).
Is there anything I can do to get support for this card? At least I'd like to be able to change resolution. Or do I simply have to wait for a new ATI driver?
we are considering to purchase a laptop that comes with the ATI Mobility Radeon� HD 5430 Graphics Card with 512 MB Ram but unable to get a test with a live cd know /using this card and can confirm that it is working okay with linux?
View 4 Replies View RelatedI remember when 11.3 first came out it was an issue.Are the fglrx drivers good now?
View 6 Replies View RelatedDoes someone have a magick trick to make this card runs well on linux lspci shows this:01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200]Ive tryed the ati binaries and its very bad.It takes a delay to switch from window to window and when tryed to play video it plays in slow motion doesnt matter what I do.Some ideas?I dont want 3d things only a good 2d performance.
View 2 Replies View RelatedI've upgraded (reinstalled) from Slackware 13.1 to 13.37 on an old iMac and have problems with slow graphics.
lspci says this about the graphics card:
Code:
With Slackware 13.1 I had no KMS enabled and graphics speed was okay. It wasn't very good, but okay for everyday work. Now with 13.37 it's extremely slow. glxgears runs with only around 38 fps, no matter what I do. And every now and then when logging off, I get a black screen and no new kdm-login. But I can ssh into that machine and restart X by issuing 'init 3;init 4'.
KMS is enabled (I've also tried disabling it, but then KDE crashes right after logging in) and it's a fresh installation of 13.37 with a 2.6.37.6 kernel.
What can I do?
I have to admin I don't know this video and X stuff very well and I used to have machines with NVIDIA cards.
If there's anything else than the usual Xorg.0.log needed.
To me the log doesn't look like there's any problem whatsoever:
Code:
I'm running Ubuntu 9.10 on an oldish IBM Thinkpad X32 (12.1in 1024x768 LCD, 16MB ATI Radeon). On the initial install of 9.10 I couldn't get any higher resolutions working, following the instructions in [URL]..
1024x768 resolution is running ok but some graphics are noticeably slow - a prime example is the "File Browser", switching from one app to this app, you see a grey window for a second, and then finally the File Manager displays.
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
# Screen "Screen0"
InputDevice "Mouse0" "CorePointer"
[Code]...