Ubuntu Installation :: 10.04 64-bit Server With Vmware And SSD - Setup The File System On Each Partition?
Apr 24, 2010
I have just bought two SSD, Intel X25-M 80GB, to install Ubuntu 10.04 64-bit server with vmware on a computer with 8GB RAM. I have tried to find out how to set up the system, but is somewhat confused on the setup. The idea is to use software raid to aviod data loss if one SSD is giving up in the future. When installing I have thought about using tree partitions.Swap Root Vmware vhd When reading about how to optimize vwware I found this:
Quote: Disks, Disks, Disks: I always attempt to put my guest OSs on their own partition and I format that partition thusly because VMWare server reads guests in huge blocks (/dev/sdb1 is the partition my guests reside on): mke2fs -b 4096 -R stride=8 /dev/sdb1
Then I set the block readahead value to somewhere around 16384, but you can go as high as twice that value (in my case this is an entire disk array, so I dropped the partition indicator): blockdev �setra 16384 /dev/sdb
How should I setup the file system on each partition? When using an SSD, each partition should be aligned. How do I do that? Let say I would like to have 4GB swap, 60GB root and the rest for vmware. At last, I have fount out that full support for TRIM is supported by kernel v2.6.33. Ubuntu 10.04 is using v2.6.32? If so, for full TRIM support I must upgrade kernel to v2.6.33.
i tried installing windows 7 on a partition on my laptop but i'm getting this message:"setup was unable to create a new partition or locate an existing system partition "i tried googling and found that it has something to do with the number of partitions:my hard disk layout right now:
I completed the installation of VMWare Server 2.0.2 onto a CentOS 5.4 64-bit distribution. There is a VMware virtual machine file on the server in question, and I want to activate it through the application console.
I did not see anything readily apparent that would facilitate the importing of the virtual machine file. Does anyone have a procedure that can accomplish this task?
I have installed fc12 on my core2due machine, and I have installed the vmware server on it, its rpm is installed successfully with out any error, after that a message is displayed
The installation of VMware Server 2.0.2 for Linux completed successfully. You can decide to remove this software from your system at any time by invoking the following command: "rpm -e VMware-server".
Before running VMware Server for the first time, you need to configure it for your running kernel by invoking the following command: "/usr/bin/vmware-config.pl".
I tried this command and find the this message
[Akram@localhost Downloads]$ su -c "/usr/bin/vmware-config.pl" Password: Making sure services for VMware Server are stopped.
None of the pre-built vmmon modules for VMware Server is suitable for your running kernel. Do you want this program to try to build the vmmon module for your system (you need to have a C compiler installed on your system)? [yes] yes
Using compiler "/usr/bin/gcc". Use environment variable CC to override.
Your kernel was built with "gcc" version "4.4.2", while you are trying to use "/usr/bin/gcc" version "4.4.3". This configuration is not recommended and VMware Server may crash if you'll continue. Please try to use exactly same compiler as one used for building your kernel. Do you want to go with compiler "/usr/bin/gcc" version "4.4.3" anyway? [no] yes
What is the location of the directory of C header files that match your running kernel?[/usr/src/linux/include]
Now it asks me in last lines that "What is the location of Directory of C header files that match your running kernal?"
Installing from live cd there aren't many choices for file system. If my info is correct reiser4fs can be used on fedora 10, if so how, if not what are the recommendations.
I want to explore DNS and Sendmail. So I downloaded exe of Vmware 2.0 on Windows Xp. I installed Fedora Linux on Both. Now I have bridged networking and do did provided:
Instance 1:
Machine IP: 192.168.1.100
Instance 2:
Machine IP: 192.168.1.101
BIND Software is installed on both the machine. I want to make 192.168.1.100 as Server and 192.168.1.101 as Client.
Also do let me know how can I setup DNS server? Will it be possible to learn DNS server and client configuration through VmWare?
I presently have an Ubuntu server 64-bit running VMware Server 2.0 in a test lab. The server was created using the default partitioning method during the installation. So I have what I think is just one huge 300GB partition along with what I hear is a uselessly large swap partition.
I keep reading that theres an advantage to creating dedicated partitions, especially for the the VM datastore.
If the advantages are true then I would like to re-partition the drive.
What partitions should I define and how big should the be?
Is there recommended file system for boot partition. Debian default use ext2. Why? Can it be used ext4? I know the difference between ext2 and ext4. But why, currently in Debian, boot partition is ext2 and all others are formated with ext3...
I have a Dell Mini 9 netbook. The SSD took a dump, so I ordered a Super Talent 16gb replacement. I put it in yesterday, tried to install 10.10 and constantly get errors. The first error, which I haven't had since, was [ERROR 30] Read-only File System. The install obviously failed. Wondering if perhaps the file got messed up in translation, I redownloaded 10.10, reformatted the flash drive (sandisk cruizer 4gb), put 10.10 back on via the program on the Ubuntu site. No luck, but no longer the [error 30]. Tried again using Unetbootin, no luck. Rinse repeat a few times, no errors just a working cursor spinning and spinning and spinning and spinning and.. you get it.
Tried to put WinXP on it just because I was that frustrated, no luck.
Now I'm back to Ubuntu (because let's face it, who wants to deal with Windows, christ they make it so complicated). I'm currently using 10.04 because I was hoping (praying) it might just be a 10.10 thing.
No such luck, now it goes to step 7/7, starts, and 5% of the way thry "creating ext4 file system" it says "the ext4 file system creation in partition #1 (0,0,0)(sda) failed." I have checked the SSD in the Disk Utility, SMART tests are clean. I have gone to terminal and run fdisk and had a smarter person than me look at the copypasta, no errors, I have deleted all existing partitions in gparted and started fresh. I have tried the auto partitioning, I have tried manual, I am going insane. Literally insane. My preschooler thinks I've leaped off the deep end.
Could it be my flash drive? Could the SSD be defective despite the tests coming back clean? What do I need to type into terminal? Is there a way to entirely entirely entirely wipe the SSD to make it fresh-out-the-box clean? I will happily provide whatever you need if it means I can get my husband off my back about this stupid netbook with its stupid tiny keyboard.
I am having problems resizing my partition. Basically I have a vmware server running 4 OS's and I have already changed the HDD size to 40GB in the profile configuration of the virtual machine. Now I want to edit the main partition to extend from 15GB to 40GB. I have searched everywhere but unfortunately none of it seems to work for me. This is what I have at the moment. (Booted from PMagic Disk) [URL]
What file system should I use to partition a slow and old hard drive? I know that ext2 was best for old computers which mine is not but I am using an old hard drive for extra storage and I was curious if anyone knew if using ext2 or ext4 would show any performance differences.
I can't seem to get past step 6 of he installation of Ubuntu 10.04. I get the error: The ext4 file system creation failed... on single partition (no raid). I chose ' / ' as the mount point, and have tried with and without a swap drive. I'm installing on a Sony VAIO VGN-NS160D, and the HDD was previously formatted to NTFS. There's no other OS so I don't see any way of getting a command line to try a sudo fdisk..
I am about to get a new laptop here soon and I was planning a dual boot like I have on my current laptop (Win7 and Ubuntu), but I have something special in mind. I looked around the forum to see if there was anything like what I had or if it was even possible but I didn't see anything quite like this.I was wondering if this was even possible, and if so, would anyone be able to tell me what filesystem I should use for my windows swap partition?
We are trying to set up a NIS server on a CentOS system. We need to have a NIS server which can provide NIS authentication to a couple of clients. We are practically new to all this stuff.
Just googled to find some ideas about installing ypserv and ypbind and portmapper. We did all that and also started them successfully. But now the clients are not able to join to the NIS domain . The error log states "YP_DOMAIN NOT BOUND".
I guess we have not entered the /etc/yp.conf, /etc/hosts files properly. Please let us know the detailed steps to setup a NIS server .
Also, please let us know what entries should go into the different /etc/<file_names>? What is meant by HOSTNAME in the /etc/hosts file?
Is there any other files which need to be changed? Are we missing any steps?
Also to add-on, while executing the ypinit command we faced the following error:
At this point, we have to construct a list of the hosts which will run NIS servers. localhost.localdomain is in the list of NIS server hosts. Please cont inue to add the names for the other hosts, one per line. When you are done with the list, type a <control D>. next host to add: localhost.localdomain next host to add:
I am trying to install windows 7 on my harddive, I am running ubuntu 10.04 and have windows 7 on DVD.I was until recently also using uberstudent, which I deleted (100 gigs) to make space for windows.However once I get to the windows start up I get a message: setup cannot detect or create a partition for this partition. (not word for word).
I grabbed the new lubuntu 10.10 from [URL] but it turns out I'm having a problem installing it on my netbook (Asus Eee PC 1015PED). While installing, this error pops up:
Quote:
The attempt to mount a file system with type ext4 in SCSI2 (0,0,0), partition #1 (sda) at / failed.You may resume partitioning from the partitioning menu.I'm installing via USB and have selected the option to erase everything and use the full HDD.
Unable to install Ubuntu 9.10 on a new internal harddrive. The hardrive contains no operating system. This hardrive is the only drive present in the system.
Whenever the installation trys to mount the ext4 partition the following error appears: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition #1 (sda) at /failed
Iv'e tried over and over to get past this error to no avail.
Is it possible to install Snow Leopard 10.6.6 VMware AMD edition (which I downloaded) on VMware linux? It is under Windows 7 so I just need to know if everything of VMware linux (like Hardware Virtualization) is the same under linux as for Windows.
I have tried to automate the configuration of a usb drive with not much success.
The problem that I have is that I have a large amount of usb drives that have a partition table of type "loop" and I need to change them to "msdos". The size of the drives vary and I need to use FAT32 or FAT16 file system.
I've tried various partitioning commands and gui applications but cant find one that I can give a one line command to to set the partition table, maximum partition size and file system.
I have searched for answer to this question but cannot find one. I am trying to install ubuntu 8.04.2 on my Acer TravelMate 290 but when I get to the install stage I get the error message "the file system creation in partition 1 of sci1 (0,0,0) (sda) failed". I am dedicating the entire HD to ubuntu, no windows and no dual boot.
I'm running Karmic Server with GRUB2 on a Dell XPS 420. Everything was running fine until I changed 2 BIOS settings in an attempt to make my Virtual Box guests run faster. I turned on SpeedStep and Virtualization, rebooted, and I was slapped in the face with a grub error 15. I can't, in my wildest dreams, imagine how these two settings could cause a problem for GRUB, but they have. To make matters worse, I've set my server up to use Luks encrypted LVMs on soft-RAID. From what I can gather, it seems my only hope is to reinstall GRUB. So, I've tried to follow the Live CD instructions outlined in the following article (adding the necessary steps to mount my RAID volumes and LVMs). [URL]
If I try mounting the root lvm as 'dev/vg-root' on /mnt and the boot partition as 'dev/md0' on /mnt/boot, when I try to run the command $sudo grub-install --root-directory=/mnt/ /dev/md0, I get an errors: grub-setup: warn: Attempting to install GRUB to a partition instead of the MBR. This is a BAD idea. grub-setup: error: Embedding is not possible, but this is required when the root device is on a RAID array or LVM volume.
Somewhere in my troubleshooting, I also tried mounting the root lvm as 'dev/mapper/vg-root'. This results in the grub-install error: $sudo grub-install --root-directory=/mnt/ /dev/md0 Invalid device 'dev/md0'
Obviously, neither case fixes the problem. I've been searching and troubleshooting for several hours this evening, and I must have my system operational by Monday morning. That means if I don't have a solution by pretty early tomorrow morning...I'm screwed. A full rebuild will by my only option.
i was thinking is it possible to port an entire linux installation onto another operating system using vmware for example? what i mean is that is it possible to create an image of a hard drive and let it work through vmware as client from another OS?
Opened VMware Infrastructure Web page and created new machine. Still OK
Click on new machine and go to console and power on.
Receive error:
Cannot access virtual machine console. Request timed out. The attempt to acquire valid session ticket for "xxxxxx" took longer than expected. If this problem persists blah blah blah
I suspect this is a problem with Mozilla Firefox 3.6.3.
Is there a way to setup a separate /home partition during a new installation of Ubuntu? If so, how. I've found guides about how to do it after installation, but it seems there ought to be a way to do it that way from the very beginning.
I am a newbee and am not too sure, but anyway, here it goes. What would you recommend as a partition setup for a laptop with 1gb ram and 160gb hdd? Please note, the setup needs to be able to keep all documents, settings and programs on updates and whatnot.
I decided to use my old computer for torrent downloads and perhaps for mirroring the slack -current. However, the computer is rather weak: Celeron 1,2Ghz, 256 MB RAM. So, which slack release is better to use? I aim to use the jfs file system, but I'm not sure it is good choice.