I want to use a different bmp image in Lilo when the system boots up. What I want to know is how do I get this new image to confirm to the specs as detailed in liloconfig. Or are these specifications only a guideline?
View 15 Replies
I understand that making any changes wrt to kernel on Slackware one has to rerun Lilo. If an install was made onto a disk already using other distros and Grub and wanting to keep Grub, do I still need to install Lilo?I believe that one could use the 'chainloader' entry in Grub to boot the Slackware. And Lilo can be installed to its own / root partition.I suppose really what I'm asking is Slackware totally dependent on Lilo?
View 26 Replies View RelatedI'm receiving the following error message when running LILO under SystemRescueCD after installing Slackware 12.2 (the slackware setup hung when installing LILO so I am trying to install manually - I have re-run setup, including formatting all drives again):FATAL: Trying to map files from unnamed device 0x0010 (NFS/Raid mirror down?)Let me know if any more information is necessary and thank you in advance for any help you can provide.
View 7 Replies View RelatedI have just reinstalled slackware on my old p4 3.2 box clean install formatted hard drive no other packages installed.is there something seriously changed from slack 10 to slack 13.1 ?? or do i suffer from C.R.S ( cant remember s***)
View 5 Replies View RelatedI'm trying to install Puppy 525 on my Slackware 13.37 PC as a dual-boot using LILO. Puppy is living, all on it's own, in sda6, a 6 GiB partition. It got there by using the Puppy Universal Installer and selecting a 'Full' install, not a 'Frugal' install. I cannot find 'LILO' type instructions, only 'GRUB' type instructions.
Has anyone succeeded in doing a hard drive install of Puppy with the LILO boot loader?
Edit: I'll probably regret it, but I used Puppy's GRUB installer.
I'm fairly new to Linux so I'm going to need a step-by-step guide to get me out of this rut. The install of Linux was fine but when I booted up I got this error. VFS: Cannot open root device "302" or unknown-block (3,2) append a correct "root=" boot option;here are the available partitions;
0800 78150744 sda driver:sd
0801 47428608 sda1 <-- this is my Windows partition
0802 30719552 sda2 <-- this is my Linux partition
0b00 1048575 sr0 driver:sr
0b01 1048575 sr1 driver:sr
Kernel panic - not syncing:VFS:Unable to mount root fs on unknown-block (3,2) I guessed from reading this error Lilo isn't pointing to the right partition to boot from? How will I fix this? I read another thread about boot problems on these forums and a guy said to do this:
#mkdir /slacktemp
#mount /dev/device /slacktemp
#chroot /slacktemp
#cd /slacktemp/etc <-- for me it told me that doesn't exist
#vi lilo.conf <-- couldn't do nothing and was frozen
#lilo -v -t -b /dev/device
#lilo -v -b /dev/device
The above solution did not work for me. Can anyone shed a light on a Linux rookie?
I just did a fresh install of slack 13.1 on a separate drive to the one I was previously using. I've been having trouble getting lilo to work, so that I can choose between either drive. Lilo is currently installed to /dev/sda, with the old system on /dev/sda1 and the new installation on /dev/sdb1. I keep getting errors like these:
Code: Fatal: Trying to map files from unnamed device 0x0011 (NFS/RAID mirror down ?)
I managed to install lilo from the old system by copying the kernel image from the new system into the /boot/ directory and running lilo. I am now on the new system and trying the same thing in reverse but it isn't working. I have searched around a bit and there's a lot of talk of chroot-ing into the other partition to run lilo. I don't understand why the process isn't working both ways though. I can't run lilo on my new installation even with the two kernel images in the local /boot/ folder. Is this something to do with btrfs or am I missing something to do with lilo? This is my lilo.conf file. I am trying to run lilo using this file from my new installation on /dev/sdb1 and getting the error given above.
[Code]...
i installed slackware 13.1, previously i had slackware 13, i made the following partitions:
[Code]...
everything went fine until i rebooted slackware after installation. lilo didnt boot at all, just a black screen. i booted with the DVD, and checked the lilo config file. the contents on lilo looks fine, just like any other lilo on google. for example i have this: boot = /dev/sda
i installed lilo on the MBR., i then changed this to boot = /dev/sda1 , on root and nothing same thing lilo always complains at the end: Partition entry not found , but how come , /etc/fstab shows all partitions are mounted ,( i am doing this in KDE environment). i reinstalled again , same thing. I also get a warning: video doesnt not support VESA mode, i changed to vga = normal again it complains that video doesnt support vesa even when i set it to normal, (note that i am running lilo after i made those changes, even rebooting , and same thing happens.
when i installed lilo, it let me choose video modes for the boot screen because lilo showed that my video card supports vesa mode, but then it doesnt boot at all. did slackware 13.1 changed so much that my laptop is no longer supported?? everything was fine with slackware 13 or is it because slackware needs a separate /boot partition, if so how come i just installed slackware 13 with just / and swap?
I finally got everything installed and then slackware setup prompted me to reboot. then i did and it just took me back to windowsxpx64. so then i tried booting off my usb, and it worked, however when i login as root, i just get the bash commandline and not interface or programs or anything. i cannot login as any other user and the setup did not prompt me to make another user account. so how would i activate lilo or make it so i can boot with it to slackware? i rather use grub but for now i would just like to get slackware working right.
View 2 Replies View RelatedI've install Slackware 13.1 and i cannot shutdown my PC. The shut down process stop while trying to run PCMCIA module.
This is the first time that happens.
From Hardware point of view , i didn't do anything at all (if that helps).
Anyone upgraded php to 5.3.x in slack 13.1?
Could you please share the slackbuild?
I installed a slack 13.7 on an old laptop. KDE was set as default desktop. then I login and run startx and I saw KDE first screen display. after that I saw blank screen with a mouse on it. Then it stayed there and it seems try read some in my harddisk since the persistent harddisk light.
View 3 Replies View RelatedWhen I try to put slackware to sleep or have it hibernate the system simply sits with a black screen. Normally it would do this for a short period of time immediately before the actual sleep state (screen powered off, croissant light on) is entered, but currently it does it indefinitely. My sleep USED to work just fine, it broke after some unclean shutdown or another, basically I just want to know what I can try resetting to try to get it back to normal.
Slackware64 13.1, running on thinkpad X61.
EDIT: Of course the second I make the post I think of trying to sleep/hibernate from the command line instead of through X/GDM (Gnome SlackBuild). That works.
I have some doubts about the official Pat's upgrading procedure. In the UPGRADE.TXT file, one of the stepts says:
Code:
upgradepkg --install-new *.t?z What does --install-new mean? Pkgs I have no installed on my 13.1 will be installed on the 13.37 upgrade? For example, I did not installed KDE on 13.1. Will be installed when upgrade? - What about third party pkgs? Slacky, SlackBuilds.org, compiled by myself. Should I remove them before upgrading slack?
Does it mean that a 64 bit version is not multi-core?
View 11 Replies View RelatedI look after some small office where computers run ubuntu. Sometimes they phone me for help. For that reason, I decided to install ubuntu alongside with my slack.I seem to have problems with lilo configuration. Ubuntu is installed on software raid :
/boot = md0 (raid 1 of sda1+sdb1)
/ = md1 (raid 0 of sda2+sdb2)
That's lilo.conf:
Code:
append=" vt.default_uft8=0"
boot = /dev/sda
bitmap = /boot/slack.bmp
[code]....
Code:
Fatal: open /vmlinuz-2.6.31-9-rt: No such file or directory
I can mount md0 without problems and the file name seems to be correct.
I finally installed Slackware and now I have Windows, Slackware and Ubuntu in my laptop. I installed Ubuntu at the last order and at that time GRUB the default loader. But I feel that I'd like to use lilo more, so I booted into Slackware and run "lilo" and then lilo became the default loader.But then I cannot access Ubuntu anymore. Because in lilo there're no information about Ubuntu. So I added some information about Ubuntu according to that of Windows in lilo. But that failed. I still cannot access Ubuntu. I searched for the posts about this problem, and this is what they say:
Quote:
image=/ub/vmlinuz
label=ubuntu
read-only
root=/dev/sda7
initrd=/ub/initrd.img-2.6.28-13-generic
or something like this. But in my slack I cannot find the image or the initrd.
I have been given a new old computer, Asus K8N-E with a 2GHz AMD Athlon 64.OpenBSD and Debian works like a charm. But with Slackware 13.1, LILO won't be installed properly. There are two disks: a 10GB ATA-drive with the system and a 250GB SATA-drive as a data repository.
Apparently the computer insists that the SATA is the first disk. Subsequently the bootable partition is not on the first disk and disables LILO to be installed. This is when I try to install LILO to a partition. When it is installed to MBR, it says something about overlapping and can't boot.
I've read that you can fix lilo after a bad edit by booting from install cd1 and entering: Code:boot: bare.i root=/dev/hda X noinitrd ro at the boot prompt. Can someone confirm this or suggest a better way? I'm using slackware 13.
View 3 Replies View RelatedI'm currently dual-booting slack 13.0 and ubuntu 10.04 When slack was originally installed, I had an earlier version of ubuntu on it, and lilo did not pick up the ubuntu. At that time, I didn't care, because I had no use for the 'old' ubuntu. When I installed ubuntu 10.04, the boot config file (/boot/grub/grub.cfg) did include an entry for slackware. Great! I am looking forward to upgrading slack to 13.1, but I want to make sure this time that I can also boot ubuntu, should I need to use it.
1)Slack installation instructions that would enable me to include the other distro in the initial install
2)Instructions on how to edit andprocess lilo.conf after the slack What follows is a dump of df from the ubunutu 'side'..
Code:
tim@bart:~$ df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda6 52866604 6227476 43953640 13% /
none 1478976 300 1478676 1% /dev
[code]....
With the continued growth of SATA devices, I have really been having problems with my boot loader. In the old days, it was pretty easy to make sure that the IDE devices stayed put. However, now everything is an sd device. Specifying a root directory of /dev/sda1 in lilo is no longer a sure thing. If you have a USB device plugged in or an ESATA device, your sd devices are no longer guaranteed to stay put.In reading through the lilo documentation, it appears that you can specify root devices by UUID or even by LABEL.
View 10 Replies View RelatedI installed Ubuntu 10.04 on a spare partition, but didn't want to install Grub since I'm sure Ubuntu isn't going to be around for more than a little test drive. The problem I have is that lilo doesn't like the initrd.img file, complaining that it's too large. I'm assuming this file should be in the initrd line for the lilo entry. If someone is booting Ubuntu 10.04 with lilo it would be nice to see the lilo entry or any tips.
View 4 Replies View RelatedMy thread "Can't add Ubuntu into lilo.conf" was merged with this one.That problem has been solved, As I solved that problem, I got several more questions: When applying the changes by run "lilo", there's a warning about "large-memory". How come and how to solve? When loading into lilo, there's a capital character "U" in front of "Ubuntu". At the same time, there's nothing in front of Slackware or Windows. I wonder why. And, now that lilo read the booting info from slackware, if sometimes slackware get collapsed, could I still be able to access lilo? If I can access lilo, can I still boot into the other OSes?
View 4 Replies View RelatedDuring the upgrade of my slackware from 13.0 to 13.1 an electric problem happen on my sony laptop. So the upgrade is fine, disk is fine but no time to run the lilo for configure the new boot. Now impossible to boot. I boot on a backtrack live CD, and can't repair my lilo.Is someone could help me. I use slackware since the 3.2 (kheops in french).
View 3 Replies View RelatedI just installed Slackware 13.37, and it's my first version of Slack.
After installing, Grub was still installed on my system, but since it is supposed to boot an OS that's no longer on the hard drive by default, it drops to the Grub Rescue prompt every time I boot.
How can I boot Slackware from grub, or get lilo to boot my system instead of grub?
I have a question that is really probably a lilo question, but here goes. Can you use lilo to boot different linuxes on separate hard drives. Like this.
/dev/hda1 - Slackware 13 with lilo in MBR
/dev/hdb1 - Puppy linux
Here is my lilo image area:
[Code]...
Boots Slackware ok, but when booting puppy it screws up and seems to be printing the boot messages for the Slackware kernel on hda1. Now, how do I tell lilo to find the puppy kernel?
I have a laptop that I have installed Slack-current on, I am currently using the usb image to boot from. Windows7 is installed on sda2 and sda2 has been marked with the bootable flag, I would like to use lilo to boot the laptop do i install lilo to sda or to sda2?Will win7 still be able to boot using lilo as the boot loader ?
Another issue i noted during install is that the kernel panicked using the dvd to install with an error stating it could not read from the booting device, I eventually used the usb-pxe install to load the system however since 13.1 i have not been able to load a system using the dvd.
When I installed Slackware, I did not install LILO. Instead, in my LMDE, I ran: grub-install --recheck /dev/sda, then I ran: update-grub, then: reboot. This worked ok, although I have 4 grub enteries for Slackware - who knows why, but there are 4.I decided to install grub from the Slackware DVD. I copied the extras/source/grub folder to home and as su, ran pkgtool and selected grub from /tmp.From the root directory, as su, I did: rub-install --recheck /dev/sda but when I tried: update-grub (or grub-update), I got: command not found. I rebooted... (probably should not have done that)Grub menu sort of appeared with not boot options.I rebooted into Slackware from the Slackware DVD and now I am writing this from my Slackware installation.
View 5 Replies View RelatedI have a XPS 1530 and when I type
lsusb
[code]
It seems to be that the camera is recognized by the OS but it is not working when I try to use it in skype or in EVO.
Has anyone here succeeded in getting armed slack running on a consumer kirkwood device .ie. one without serial console? I have a tonido plug that I want to liberate. By default the plug boots first from the external usb, so I would only need to set up / on the first partition. I would be very interested to know if someone had managed to install slack to the internal nand without bricking it.
View 9 Replies View Related
