I setup a server with vmware esxi 4. I installed opensuse 11.2 and I have successfully setup an internet gateway and I manually configured (static) my client IP. My question is, is there any software or commands that I could use to manage the bandwidth usage for each client? eg. only 5Mbps for 192.168.1.5, 10Mbps for 192.168.1.10, etc
View 3 RepliesCan you suggest bandwidth monitoring software for GUN/Linux that will log bandwidth based on usage/consumption.
Not options:
- slurm or any other "real time" bandwidth monitoring
- /sbin/ifconfig <interface> | grep "RX bytes" or the like
What do you use to monitor your monthly, daily, hourly bandwidth consumption (assuming that you do).
I just wanted to use a network bandwidth usage monitoring application. Scenario: I am using an EV-DO based USB broadband modem with a limited GB plan. For additional data usage they charge per MB. Currently I use either wvdial (mostly) or pon to start the connection. So if there is any network monitoring application which could log time used and data used for the session, it would be great. Actually debian has too many different network monitoring applications, But I am not sure which one suits well for this purpose.
View 5 Replies View RelatedI have a network connection between 3 computers sharing the same net bandwidth with the same router (modem), I wanted to know how much every one of this network taking from the bandwidth, I want an easy program like switch-sniffer (see the pic) to scan the network and tell me how much every one taking from this network in real time.
View 14 Replies View RelatedI'm running Ubuntu 10.04 and all was well on my home network until a household member decided to get a laptop and jump on my network. All he does is watch videos on ....., download crap from P2P sites, and maybe even watch p0rn. Is there something I can use to control this or maybe set my router to give him the minimum resources available? Also, I want to block him from downloading junk from P2P sites or places he might get a virus. I'm on a D-Link DGL 4500 Router.
View 1 Replies View Relatedis there any way to monitor each application network bandwidth usage ?I've used gnome-system-monitor, but unfortunately it just show the total network activity
View 3 Replies View RelatedI have a third party program (tightvnc) which I want to monitor and detect if it loses a connection with a client. I don't care if the client has the program open but isn't doing anything with it, I only want to know if the actual TCP connection is lost.
Since TCP takes forever to die on it's own I was thinking the best way to detect if a connection is lost is by bandwidth the bandwidth on the tcp port allocated to the VNC connection. Are there any tools built in to redhat (RHEL 5.2) which I could use to do this? Since I don't have full control of the operating system I would prefer to use built in tools rather then trying to get a new tool installed.
How do I find out the network usage ie the total amount of data is transferred in or out of my computer (openSUSE 11.2 and gnome) and keep a track of the total network usage?
View 1 Replies View RelatedI need to monitor network performance/usage based on protocols.
About snort now, is perfstat.c is replaced with some thing else?
I'm looking for an effective way to manage use of internet bandwidth by users on a local area network. Currently there is a simple broadband router and unmanaged switch, and a standalone Ubuntu Server (8.04) that provides DHCP, DNS and mail for the LAN, and a web server. Ports are forwarded from a static external IP address to HTTP, HTTPS, SMTP, SSH and IMAPS, and some security is provided by IP Tables (managed by using UFW).
There are 5 users on the network, and currently one or two of those 5 are using beyond our monthly download allowance of 30Gb. 1) To be aware of how many users are currently using the internet connection, and to divide the bandwidth between that number (so that if there are, say, 3 active connections, the total bandwidth available is divided 3 ways, rather than one of those users being able to hog all of it).
2) To allow each user to download up to 1/5 of 30Gb each month without any additional throttling (apart from the above), but once they go over that allowance to throttle them individually to, say, 10Kbps until the start of the new month.
I've heard other threads talking about both IP Tables and a proxy server such as Squid. I have no idea which of these would be most suited to the task. Currently, as I said, the Ubuntu server is standalone and only using 1 NIC, but it has 2 NICs and I could be configured to act as a gateway for the LAN, instead of the router, which is set to be the current default gateway.
I am using SQUID 2.6 on cent os. Squid as a proxy server is working fine. I want to manage my bandwidth according to my office staff.Like for top management users may allocate 1 MB and rest of the users as 256 kb.Kindly guide me that how can I do it ?
View 1 Replies View RelatedI have downloaded and setup the SUSE Lifecycle Management Server on vmware using the Live CD Distribution. I have connected it to Susestudio.com as my repository and setup a user account via the backend on pg 96 using the slms-admin-ui-user -o to create my administrator account since I lost the password for the initial login. I created a customer and have the following:
Mirroring Credentials - User Name: (random character)
Mirroring Credentials - Password: (random character)
Also I have a test box for installing the Live CD of our application. Do all appliance created on suse studio have the client to connect to the SLMS server or do need to install a client? If there is no client how do I obtain and add it to the appliance on susestudio.com ? How do I setup appliance as a client?
network manager isnt showing any network interfaces. ifconfig shows wlan0 and eth0 and internet is working. how can i get network manager to manage those connections?
View 8 Replies View RelatedWe would like to setup Lenny (Gnome) clients and need Desktop Mgmt Software, to manage clients over central management system.
View 1 Replies View RelatedI am Network Administrator in a Degree College managing around 2500 Comps. My ISP has terminated its Internet link (15 Mbps) to our Linux Server (Installed 2 NIC) from where Internet connection is extended to rest of the machines in network. I am supposed to send different bandwidth to different departments say 5 Mbps to Hostel, 2 Mbps to Staff room etc. I am new to linux and don't know anything about Bandwidth Management in linux.
View 2 Replies View RelatedLooking for a way to control how much cpu apps are allowed to use. I'm 10.04 64bit dual core.
View 8 Replies View RelatedWe have an Apache Subversion (http) server for hosting our codes, and, for the 3 next month, we are behind a DSL connection (max upload 100 kB/s).
When a remote co-worker try to download a new fresh copy of our projects on his computer directly over http, the transfer goes fine : with a bandwidth monitor (gnome-system-monitor or bwm-ng) we can see that the server is trying to send ~95kB/s and the connection remains usable for others task in parallel (just a bit slower, which is normal).
But : when the remote co-worker is connected through SSH to this server, and uses tunneling to communicate with Apache Subversion, the server is sending more than 200kB/s : the connection is not usable for other tasks during the transfer as with ~102kB/s actually transferred through the DSL Line, it's completely congested and more than fifty percents of the packets are lost.
I think that I understand why : TCP/IP auto-detects the max amount of successfully transmitted bytes per second, and try not send more than this maximum value.
When the Apache server is connected to the local instance of openssh-server through localhost, packets are transmitted successfully between them. Only after, openssh-server try to send it to the client (and should retry if it's not successfull) but during that time, Apache is already giving the next one... giving this saturation effect (Apache is not aware of the saturation, or at least, not enough)
I wanted to implement a server for a small network, but am a bit in-experienced. The server that I want to use should be able to do load-balancing (two connections) and also act as firewall/proxy. And also it should be able to do some bandwidth management. The network that its going to serve has two parts. One part of the network should be served, say during day time,and the other during night time. The one that is going to be served at night-time should not have access to internet during day-time, but should have access to, say local mirror-server. I am a bit confused what software/hardware to use. I am planing to use EndianFirewall, but since I don't have experience, don't know if it can do all that I need (?).
View 1 Replies View RelatedI'm getting DDoS attacks on my server, and I need to block all the attacking IPs.But for that I need to know which IPs are attacking me.I was thinking that I should log the bandwidth usage per IP so I can tell which IPs are using excessive bandwidth.How can I achieve this? I'm using Ubuntu 10.10.
View 3 Replies View RelatedIn my household a number of people use the internet. Up to a maximum of 3 wired connections and 2 wireless connections at its peak, all connection through my D-LINK G604T router. The problem is, when one person is downloading or watching ..... or whatever, the others using the internet suffer. I've spent hours configuring QoS on my router, and long story short, no matter how I configure it, it just simply does not work. QoS in no way shape or form limits connection speed (which it says it should). Anyway.
I have a spare computer under my desk, and I'd like to know if I could set this up with a (free) linux distro that limits bandwidth speed per connection. For example, of the 1500 kb/ps (about) my modem pulls, is there a way to limit that to 768 or 512 per connection? so person A can still download, person B can still watch ....., and person C can still play counterstrike with a latency under 100. This would solve many, many arguments in my house I am *fairly* good with computers, but if the distro came with documentation and a GUI that would be awesome.
* TL;DR: *
Is there a linux distro I can load on a spare computer that limits bandwidth per connection, wireless or otherwise, with good documentation?
Failing that is there firmware I can use for my modem (dlink g604t) that would do the same?
Failing that do you know of any good hitmen that would solve my family arguments, ahem, permanently?
I am trying to set up an nginx server. I intend to use it with, php and python, and probably with frameworks like django and codeigniter. However, I can't get it working. This is what I did: Installed these from Install/remove software:
nginx,FastCGI,php5-fastcgi,python-fcgi,spawn-fcgi
My current nginx.conf file is this (Stripped comments):
[code]...
What happens is: when I type a php url to address bar, I only get a text saying "No input file specified." This is what I get when I make netcat sit on 9000, and go for <hostname>/phpinfo.php:
[code]...
There are clearly some config problems here, but can't find out what are they, since this is first time I try to setup nginx and fastcgi.
How to set download limit using SQUID? I want to specify the download limit for a particular list in MB. Is it possible to limit bandwith for some group of machines in network?
View 1 Replies View Relatedi wanted to do bandwidth management/traffic shaping on my Internet link(have two internet connections), but i have some questions to ask: I want to know how could i for example filter some traffics using tc and iptables (e.g Peer-to-Peer,IM,Download Managers,Flash videos..) i can do filtering for known services like http,ssh,... but since these applications doesn't use one port, i am confused a little bit. I also want to do some bandwidth allocations (based on protocol) thats why i need filtering.
The other question is that currently i am using tc for bandwidth allocation and iptables for marking packets to send to these classes, am i doing it right? I mean it does work, but is it better to use for example "U32" filters for filtering? P.S: i tried to use ClearOS in gateway mode, but it doesn't have bandwidth allocation functionality. Does anyone know if i could do bandwidth allocation in ClearOS/Endian.
I am trying to do some bandwidth management testing, so I have developed a small script for doing so. When I try to run it it gives the error <error> RTNETLINK answers: invalid argument</error>. I have searched the net, and so far they say it has to do something with the kernel support.
the script:
<code>
tc qdisc add dev eth1 root handle 1: htb
tc class add dev eth1 parent 1: classid 1:1 htb rate 2mbit ceil 2mbit
tc class add dev eth1 parent 1:1 classid 1:10 htb rate 600kbit ceil 2mbit prio 2
tc class add dev eth1 parent 1:1 classid 1:20 htb rate 1400kbit ceil 2mbit
tc class add dev eth1 parent 1:20 classid 20:100 htb rate 700kbit ceil 2mbit prio 0 #when running this command it gives the error
tc class add dev eth1 parent 1:20 classid 20:200 htb rate 700kbit ceil 2mbit pro 1
</code>
I am running this script on a virtual machine that has ubuntu 9.04 installed.
I have one dedicated server in godaddy. Now I got mail regarding overage bandwidth. I don't know how to check this and I must give report how its happen.
View 1 Replies View RelatedSo if I get their public key for ssh how do I add and then how do I delete it my problem is in .ssh/authorized_keys file I do not understand how to add and how to delete the key so that I can enable and disable root login this way.I am not sure as how do I comment the key assuming that the person sends me his public key then in .ssh/authorized_keysfile how do I add so that a comment can also be added so that I can identify that person as a legitimate user.
View 1 Replies View RelatedI'm looking for opensource central management software to manage squeeze workstations.
View 4 Replies View RelatedI tried connect to internet through iPhone (bluetooth tether), so I followed one tutorial... It said I have to change "networkmanager" to "ifup" in yast>network settings, and make some other changes... I did it, but I couldn't connect via iphone... OK... I put back all changes, also changed ifpu to networkmanager.
After reboot, Knetowrkmanager gives me "network management disabled" on startup, instead of list of my networks.
Of course, I google for solution, but without any luck. And then, I don't know why, I killed Knetworkmanager, start it again, and.. it worked!
But now, I have to kill it, and start again always, when I reboot my laptop...(HP Compaq 6720s, BCM4312, KDE 4.3.4)
I have an Asus EeePc 1001PX and on resume I have "Network Management disabled", neither wired nor wireless interface can be configured, the NM icon is greyed out. running ifconfig shows eth0 and wlan0 have disappeared completely.
I found 2 options:
1. https://bugs.launchpad.net/ubuntu/+bug/555571
2. Network management disabled after start on 11.2 - openSUSE Forums
but I don't have the /var/lib/NetworkManager folder at all
How to set download limit using SQUID? I want to specify the download limit for a particular list in MB. Is it possible to limit bandwith for some group of machines in network?