Networking :: Setting Up A Local-only Network With Dhcp And Dns
Oct 21, 2010
I know there are tons of help guides out there for this, and I have looked at and tried them all. I am trying to do something really simple, and just can't seem to get it working. I have been trying on and off for the better part of a week now, with not much luck. What I am tyring to do is have a Ubuntu 10.10 server serve out DHCP addresses and be the DNS for the local network. The local network will have no internet access, so it only needs to know the names of the local server. My network setup is as follows:
1: Windows Vista web server
2: Ubuntu DHCP3 and BIND server to give IP's and resolve local names.
3: A bunch of tablet computers connected via dhcp to the network, that need to access the web server on the Windows machine.
I have DHCP working nicely, but it fails to propagate the hostnames to the tablet computers. Unfortunately I need this to work, as the tablets do not have the capability of having a 'hosts' file.I have tried just about every self-help guide I can find, and just can't seem to get this work. Everything seems to work fine except for the name resolution. Any help would be great, I don't have that much hair left to pull out!
View 5 Replies
ADVERTISEMENT
Jun 3, 2010
My router is a DHCP Server.My Access Point is a DHCP Server.I'm wondering if it is really necessary and usefull.Is it possible to get an IP from the Router through the Access Point.For exemple I connect my laptop to the wifi Access Point and the IP is given by the router only.
View 2 Replies
View Related
Jun 2, 2011
how to configure dhcp server in a local lan network
View 2 Replies
View Related
May 25, 2011
For strange reasons I was stuck without an Internet connection for about 2 hours. I couldn't establish a connection, even local network only via DHCP. This was on Natty. After 30mins passed, I rebooted to Maverick only to get the same results. With nothing else to do, one hour after, I booted into Windows XP to play Dragon Wars 2. Lo and behold! I had Internet connection. At first I thought it was a technical problem with my ISP. So I rebooted hurriedly to Natty and after several minutes of trying to coax Network Manager for a damn fre*kin* connection it still couldn't.
Back again to XP, I couldn't believe that I wasn't experiencing some kind of on/off signal from my ISP. It wasn't just a coincidence that I could connect on XP and not on Natty. The connection was fine! And I've reason to believe for the past 2 hours, my ISP wasn't the culprit. .. this time it was on my end.Now - on Natty - I manually configured the connection (Instead of DHCP) to be greeted with the familiar Connection Established prompt from notify-OSD.
View 2 Replies
View Related
Apr 3, 2010
I'm maintaining a very modest network at home, with OpenSUSE as OS on the server. I got the DHCP and routing working by following the instructions in the wiki. However, every time I run dhclient on the server/router, it appears my own DHCP server assigns an address to the internal network card despite the fact I specifically assigned it to be static using Yast. The situation resolves itself when I restart the network services with the command /etc/init.d/network restart. Otherwise no problem, but it also seems the internal network card gets a "new" IP from my server every time the external card requests one from the ISP. This is more of an issue.
View 5 Replies
View Related
Aug 18, 2010
In 11.3, if in "/etc/sysconfig/network/ifcfg-eth0" i set DHCLIENT_SET_DEFAULT_ROUTE="no" this seems to have no effect. If i start my box, the routing table has the "default route"-entry offered by a remote DHCP-Server. More Info: My Susebox has eth0 and eth1 and both network devices should use DHCP4. But from DHCP-offer on eth0 i want to use
* "offered IP-Adress for eth0"
* "offered NTP-Server"
* "offered Host-Name"
From DHCP-offer on the eth1 i want to use
* "offered IP-Adress for eth1"
* "offered DNS-Servers"
* "offered Default Route"
View 1 Replies
View Related
Nov 6, 2009
I am trying to setup my home server for test purposes. Now the IP I have assised my home server are
192.168.1.2
192.168.1.3
Port 80 is open in my firewall and Selinux is off at the moment.Now I have my DNS at my registar pointing at my home IP. Will that work? I have my name server configured with my local ip. Should I use my externel?
View 3 Replies
View Related
Feb 18, 2010
how I can define a local static IP address (so that I can run a web server off of the same IP, rather than letting my router DHCP it)?I've tried doing the YaST->Network Devices->Network Settings->Traditional Method with ifup->Set NIC to desired IP->Set Default Gateway to router address method, and afterwards I can't even get into my router anymore (not even responding to ping).
View 8 Replies
View Related
May 16, 2010
I'd like a way to see all of the devices on my local network and what their local IP address is. I recall that I used wireshark to troubleshoot a similar problem a while back, but it doesn't seem to have a way to see all of the devices- only the traffic. (I'd like to do this without having to physically interface with my router if possible, and I am in an encrypted network if that matters)
View 6 Replies
View Related
Jun 28, 2011
I have installed a web server on my local network. Everything is well configured and web pages are shown correctly from Internet (outside the local network) using the domain or the public IP.The issue is if I try to see that web pages (using the domain or the public IP) from inside the local network. In that case the router config page (192.168.1.1) is shown instead of the web pages.From inside the local network I'm only able to see the web pages using the internal IP address (192.168.1.XX).
View 2 Replies
View Related
Aug 30, 2010
I have tested several Linux Distros over the last weeks, and with all of them my DSL connection have been working out of the box (for intance Mandriva, Ubuntu, Mint). But it does not work on Dreamlinux, neither on Live CD or now where Dreamlinux is installed on my harddisk.
According to the guidelines provided by my Internet provider I need to use TCP/IP and activate DHCP. And make sure that PPPoE is not activated.
I see nowhere I can do this in Dreamlinux. In the controle panel i can run Wicd. Then I can chose to de-activate Wicd - this gives me an option of entering Adress, Networking mask, Gatway and Nameserver - for static ip it says - and this is the opposit of DHCP, right??
SO - what to do? Should I get a debian package or something? (Dreamlinux is using debian packages, as far as I could see)
View 1 Replies
View Related
Jan 2, 2011
My DHCP setting is disabled in fedora 12 . Previously i was using static IP address. I Want DHCP setting enable, any idea.
View 1 Replies
View Related
May 25, 2010
I've got an Ubuntu server hosting our websites and other various things here in our own home. We recently switched to a router that doesn't support loopback (abomination), so I've set up hosts files on our computers so we can access our own sites when on our home LAN.
However, we often take our laptops as we travel about, and I'm guessing due to the hosts files when we try to access our sites, it'll look on whatever local network we're connected to for our server, which won't work, obviously.
Is there a way to set up something like a hosts file that'll only try to look up the local IP of the server when we're on a specific network (our home one), or have one that tries to look for the local IP first, then proceeds to try and resolve the domain name and use the external IP if the local IP doesn't work?
View 6 Replies
View Related
Apr 7, 2011
I am totally new to Linux and have just installed ubuntu 10.10. After configuring the network interface via dhcp I started getting these messages that come in so frequently I can't configure anything else.
[87.186415] Stack:
Why I am getting this messages and more importantly how do I get rid of them.
The installation is on a VM on Hyper-V.
View 1 Replies
View Related
May 1, 2010
I bought an RTL8187L USB wireless adapter, and have had trouble getting it to work. I have managed to get it to work via manually configuringtime, but lost that configuration, and now it is once again not workingThe root issue appears to be (if I'm understanding correctly what I'm seeing) that when I connect, routes don't get setup properly, so when network manager (or WICD, which I've also tried) get to the DHCP step, my wireless router can't be reached by dhclient.
This is on Ubuntu 9.10, and I'm using the updated driver from realtek.com, btw, though the in-kernel driver was exhibiting the same behavior.So, two questions:- Is anyone familiar with this problem, and is there a fix available?- I believe I can work around it by setting up routes manually (e.g. with a post-connect script in WICD), but after staring at the "route" manpage, I'm not 100% sure of the commands. My router (a FIOS MI424WR) is my DHCP server, and is at 192.168.1.1, and route -n on a working PC (wired connection) gives:
Code:
dave@MinasTirith:~$ route -n
Kernel IP routing table
[code]....
View 1 Replies
View Related
May 31, 2010
I'm working with a Ubuntu 10.04 LTS system with two network interfaces (both Ethernet). I wish to setup this system such that it is simultaneously connected to my local and an OpenVPN network and able direct traffic between the connections depending on what program is sending the traffic. The problem: Under my current OpenVPN configuration all network traffic is directed to the VPN.
My OpenVPN config file (some details omitted)
--remote [gateway ip] # vpn12 load:
--remote [gateway ip] # vpn11 load:
--remote [gateway ip] # vpn15 load:
--remote [gateway ip] # vpn16 load:
[code]....
In practice, I would like OpenVPN to operate out of one of my two network interfaces and leave the other interface connected to the local network. Then by default all network traffic should be directed to my local network unless I specify (on a per program bases) that certain traffic should go though the VPN. These two network connections can (should) stay completely independent of each other and do not need to talk to each other.
View 2 Replies
View Related
Mar 31, 2009
I have two networks. One of them is wired, the other is wireless. The wired has an internet connection and a few other computers connected to it. The wireless network has a few hosts connected to it too, but it has no internet connection. What I've been trying, fruitlessly, to do, is make all connections that are bound to the internet, or my wired network, be routed that way, and all the connections to the hosts of the wireless network go that way.
Here's the setup..
Wired:
192.168.1.0/24 Gateway = 192.168.1.1
Route internet through here
Wireless
192.168.2.0/24 Gateway = 192.168.2.1
If my computer sends a packet to the internet, it should be routed through 192.168.1.1 If I send a packet to one of the local hosts of the wireless network, it should be routed through 192.168.2.1. Here's the routing table I've set up(This is one of many configurations I've tried)
Code:
$ ip route show
192.168.2.1 dev wlan0 scope link
192.168.2.0/24 via 192.168.2.1 dev wlan0 src 192.168.2.4
[code]....
With this, and everything else, I get destination host unreachable when pinging. The strange thing is that, if I unplug my eth cable, reboot and connect to the wireless network, everything is fine and I can access the router and the others. I'm trying to improve my networking skills, as I've had this of setting up a small linux box as a router for quite some time, for the fun of it, but I need to get routing under control before I go ruin my network.
View 6 Replies
View Related
Aug 18, 2010
I set up a dhcp server in the lan and assigned static ips to two computers, computer A and B, according to their mac address. Everything was running fine. But when I turned off computer A, connected computer C to the network, and assigned computer A's static ip to computer C without changing dhcp setting. Computer C was able to access the internet. When I turned on computer A, dhcp couldn't assign an ip address to it, and computer C showed an error message of ip conflict and failed to use internet. I wonder if dhcp server is able to prevent other computer from using the same static ip that is already assigned to a computer according to its mac address.
View 5 Replies
View Related
Jul 7, 2009
I have got DHCP issues with Network Manager. Whenever I try to connect using static IP it works, but when I use use Netowork Manager with DHCP, it seems to try to connect and soon says "Network Disconnected"..I've managed to connect to wlan and eth using network, so there shouldn't be any hardware/driver issue.
View 4 Replies
View Related
Mar 4, 2010
I using ubuntu 9.04. It was connected to the network with the manual IP Settings. Now the server settings have changed and we are supposed to move to Auto Assign IP (DHCP). All the windows machines are working fine, those are connected to network and using internet. But the ubuntu machine is not getting connected. Is there any any additional setting required for DHCP?
View 2 Replies
View Related
Feb 20, 2010
Using debain 5.0.4 with webmin 1.500 and dhcp3.i have two subnets (192.168.1.0 & 192.168.2.0)at home. The debain dhcp server has 1 NIC using eth0 and eth0:1 (virtual).
I have configured the dhcpd.conf file using webmin, with a shared network, given the two subents are on the same physical network. each subnet has a pool of about 20 addresses.Problem is that when a host boots up which is under the 192.168.2.0 subnet (using its MAC add - no fixed ip assignment), it gets the associated DNS and gateway ip addresses for this subnet, however, the ip address is assigned from the 192.168.1.0 address pool.
I have checked the net extensivly finding all sorts of discussions and solutions. My problem occurs in the same manner irrespective of whether i connect a host direct to the dhcp server or via a (netgear) switch! Please can someone advise on what settings i might be missing, or do i need to set up DNS/DDNS and/or a firewall/router before this works properly?
View 3 Replies
View Related
Jul 12, 2010
I installed dhcp on my Debian server and it was working fine.
untile I restart network with this :
And then dhcp was not working.
View 4 Replies
View Related
Jan 15, 2010
On my network drive web control panel I have got such an option:What would a dhcp server do on a network hard disk?
View 5 Replies
View Related
May 7, 2010
Trying to network three computers using dhcp.
Box 1: older Asus A7N8X-E deluxe w/onboard ethernet using dhcp
Box 2: new Asus M4A785-M Micro ATX w/onboard gigabit ethernet using dhcp
Laptop: Dell Studio 1745 w/Intel 5100 a/b/g wireless
Router: Linksys WRT54G set as dhcp server
Both windows boxes are set for workgroup "home"Laptop is "laptop.home"They can all connect outside to the internet but don't seem able to see each other, not even to ping each other.
View 13 Replies
View Related
Jan 16, 2009
I have a WET54g bridge that I am trying to get connected to a wireless network that only allows DHCP. The idea behind it is that I would like to connect the Cat6 out of the bridge to a switch allowing multiple wired computers to connect to the wireless network. The bridge will easily connect to the network once I put the WEP key in, however, there is a kink after that. When I connect the Cat6 to my computer and request an IP for that computer, it self assigns. This tells me that it is not talking to the wireless network through the bridge.
I can not find which IP address the bridge was assigned so that I can talk to it. The sub net is 255.255.240.0 which leaves quite a few possibilities. I know that the bridge is, however talking to the wireless network because the light is steady on the front of it which indicates just that. One other thing to stack on is that I know that there is a "splash page" which comes up when any computer connects. You click on the agreement and then you are allowed onto the network. How can I get my computer to talk through the bridge to the wireless network?
View 1 Replies
View Related
Feb 16, 2010
I've been trying to understand how Linux creates the network/interfaces on a machine (been reading the Linux admin guide), but as I'm pretty new to this subject, I've got lost in the forest.
To provide with my goal:
1.) Learn about network setups on Linux
2.) Be able to maintain my own (virtual) network
3.) Configure my (virtual) network
View 1 Replies
View Related
Jun 28, 2010
(although I'm running Solaris, I've posted here as I expect Solaris/LINUX is irrelevant) - more of a general network Q.I have a PC running Solaris 10 (hostname MARKUNIX) and a laptop running WinXP (hostname MARK-LAPTOP). Both are connected to broadband via a router. IP addresses for each are determined via DHCP (192.168.1.nn) and I do not leave either on, 24x7. I am running Oracle on MARKUNIX and want to be able to refer to it by hostname when using Oracle tools on my laptop.Each machine can ping each other ok by ip address and curiously the Solaris PC can ping MARK-LAPTOP (I'm not sure how it resolves that?) - importantly the laptop cannot ping MARKUNIX.Now I could add MARKUNIX to my laptops hosts file but that would mean changing the file each time I boot up as the ip address for MARKUNIX will keep changing (DHCP).
Is there a way to refer to MARKUNIX without having to keep changing ip addresses and use DHCP? As I understand it the 192.168 address is private and is not really the 'real' ip address and as such can be manipulated(fixed?) even whilst using DHCP?Am I right in thinking that a static ip from my broadband supplier is the ip of my connection (router) and I'll still have the same private network referencing issues?What I've covered above pretty much is the extent of my knowledge of networking so bear that in mind please.
View 4 Replies
View Related
May 4, 2010
Basically, I wanted to use the Bootp (PXE) protocol to boot a machine (my laptop) from my network instead of using USB/DVD boot medias to reinstall if need be. My router being a piece of crap, I couldn't setup the DHCP server to allow PXE packets. Confirmed from the manufacturer that it is not possible. Well for a $140 router, you would expect the opposite. Anyways, here I am with a small machine setup with Slack, no desktop environment (only CLI) and connected to my router (which I deactivated the DHCP) so the machine can act as a DHCP server. It works very well. However, I would like to install a few other utilities into that machine and for them to work, I need to put the machine between my cable modem and my router. Basically, here's the topology from outside):
Internet (ISP) --> Modem --> DHCP machine --> Router (no DHCP - acting as a switch) --> computers & printers
The problem is that I cannot connect to the modem from the computers on the network. Also I cannot access the internet (go on the WAN side) from the computers. From the computers (namely my laptop), I can ping the router, but cannot ping the interface where DHCP broadcast. Also I cannot ping the modem. From the router (using the web config page), I can ping the DHCP broadcast. From the DHCP machine, I can ping the modem. In the DHCP server, I setup the eth0 (the interface where the modem connect to) as a DHCP assigned IP so it can obtain the IP from the modem. The eth1 (the interface where DHCP broadcast) is static. All my machines obtains a IP from the DHCP machine without a hiccup.
View 13 Replies
View Related
Apr 19, 2010
I decided to take the plunge and change the existing static ip configuration for my home network to a dynamic (DHCP) configuration. The DHCP server in this new network config is my gt701-wg actiontec DSL modem.
[Code]....
View 5 Replies
View Related
Feb 12, 2009
I have installed Fedora 10 on my A860 Dell Vostrol Laptop with AR242X Atheros Wireless card. Wireless card worked out of the box and i could detect wireless network and connect to it. But i have a problem that, my wireless connection is not able to get IP address from the DHCP server. Please help me out what can i do to get this working. I am using WEP security and authentication is open system.
I have windows 7 beta installed on the same machine and on that wireless network works fine so i am sure that there is no problem with the wirless network. I am using DIR-300 router from D-LINK. I tried to see packet log on wireshark and there i see that there is no reply to the DHCP discover message. Actually i don't see any RX packets at all. Which is not normal as there is traffic on the network.
View 14 Replies
View Related
