I have two NIC cards installed, they both go to seperate networks. Occassionally I am not able to establish a connection via eth1. When looking at tcpdump traces I see that Linux is using eth0 hardware port and putting eth1's IP address in the packet to reply to the connection request. When the connections work its when Linux uses eth1's port.
View 3 RepliesI have 4 DSL modems connected with 4 different ISP's my scenario is
a) My FC-2 machine with LAN IP=192.168.10.1 and Bond0 IP=192.168.1.1
b) Modem-A LAN IP= 192.168.1.2 , ext IP=xxx.xxx.xxx.xxx
c) Modem-B LAN IP=192.168.1.3, ext IP=xxx.xxx.xxx.xxx
d) Modem-C LAN IP=192.168.1.4, ext IP=xxx.xxx.xxx.xxx
e) Modem-D LAN IP=192.168.1.5, ext IP=xxx.xxx.xxx.xxx
Modem-A, B, C, and D LAN connected with my FC-2 machine, and all 4 interfaces of my machine are in Bond0, Now please help me what default Gateway I should set in my FC-2 machine?>??? or I have to set 4 gateways in my machine?and will this configuration works?
I have to implement hardware redundancy.I have 2 linux machine for this and each have similar configuration/hardware. Lets say two machine Linux1 and Linux2. Currently Linux1 have one NIC and it has 4 IP address bind on it. Now I have to down the Linux1 and up Linux2 with same Ip addresses.
Could it possible to configure all the Ip (same)address on both Linux1 and Linux2 and Linux1 have eth:x status UP while Linux2 have eth:y status down.
I am trying it but on Linux2 machine I cant able to create multiple Ip interfaces with down status.
I want to do a video streaming to a remote PC across the internet. The video bitrate is around 600 kbps. But my internet connection supports only a maximum upload bandwidth of 400 kbps.So I thought I will get one more connection and use the combined upload b/w of 800 kbps to stream the video. I hope there should be a way to split the stream across two interface and merge them together at the remote endpoint. All this has to be done at real time.
View 1 Replies View RelatedI have a strange problem regarding networking on the Alix 2d13 running Ubuntu 10.04. The Alix has 3 physical network interfaces, lspci says:
Code:
00:09.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Kernel driver in use: via-rhine
Kernel modules: via-rhine
00:0a.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96)
Kernel driver in use: via-rhine
Kernel modules: via-rhine
[Code]...
It seems, if more than one cable is connected, a random hardware port is chosen as eth0-eth2. If only one cable is connected the port that is connected is chosen as eth0-eth2. Any idea what's going wrong here?
Looking at the output of netstat, I'm not seeing a definitive way to tell which torrent connections are clients reaching in to my machine vs my machine reaching out to the world. Is there a clear way to determine which is which?
View 1 Replies View RelatedI am trying to remember the procedure used to determine the ip address range when given a network address and its subnet mask. Does anyone have any documentation on the steps that are done to accomplish this?
View 6 Replies View RelatedI have been running into network issues lately with my CentOS 5 (installed on AMD Athlon X2 - 64 bit machine about 2 years ago). It was able to connect to the network fine until yesterday when I installed more memory into the machine restarted it.
Upon restart, the boot up was paused at 'Determining IP information for eth0' step for a while and booted with out connecting to the network. I tried restarting the network (/sbin/service network restart), but this is the error message I continuously get: Determining IP information for eth0...PING xxx.1.226.1 (xxx.1.226.1) from xxx.1.226.83 eth0: 56(84) bytes of data
[Code]...
I've seen this pop up a few times on the forum but my setup is slightly different. I have a PC with an ASUS P5N32-SLI Premium motherboard. I've just installed CentOS 5.1. Yes, I know this is ancient, but this is what they're developing on at work. I'm trying to get connected either via ethernet or wireless and neither one works. When I boot the computer to Window XP it does connect on ethernet. Ethernet should be easy so I'm concentrating on that. But I get "Determining IP information for eth0... failed." after a 'service network start'.Here is some other information that was asked on similar threads:
> uname -rmi
2.6.18-53.el5 x86_64 x86_64
> grep eth0 /etc/modprobe.conf
[code]....
i wanted to learn linux, so i just installed Centos on a thinkpad x200. my wireless will not work. when i try to activate it i get this error:
Determining IP information for wlan0...SIOCSIFFLAGS: No such file or directory
SIOCSIFFLAGS: No such file or directory
# lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
[code]....
The first thing that comes to my mind is to add (copy) the script in /etc/init.d and the /etc/rc* directories by hand. Debian's automatic handling of init scripts on package install/removal is quite nice, so I tend to shy away from making any manual changes if there's an automated way to do it. Which leads me to the question: is there an official way to run a second instance of a daemon? (Tried google, didn't find much more than a bug report).
View 4 Replies View RelatedI just had an ATT Uverse RG installed. However my Smoothwall router that previously worked fine with the ADSL SpeedStream is no longer accepting an address assignment DHCP ip address from this new gateway. (3800HGV-B)Any thoughts ideas or experience working with this hardware? ATT only supports Windows and Mac
View 2 Replies View RelatedI have a ppp0 entry with post-up options like this
mapping ppp0
map none photon-plus motorola
map timeout: 12
[code]...
I'm renting a server which comes with 5 IP addresses, but only one network device. From what I can understand I'm able to create aliases by adding entries to /etc/networks/interfaces, I haven't tried I'm in the planning stages. Hypothetically, 192.168.22.30 is my primary IP and I want to set eth0:1 to have 192.168.22.31, and then after that I want to create a virtual machine (using kvm/qemu) that is able to communicate bidirectionally to the internet over eth0:1, and leave eth0 strictly for administrating (not for VM traffic).
The qemu guides I'm finding seem to assume that I want to use TAP or VDE, what I want to use is a sub-ip/alias. One guide I saw had me eliminate everything from eth0 and put it under br0. That would leave me unable to ssh into my server (and unable to administrate). Is there a way I can do something along the lines of: qemu [options] -net [option] -netdev=eth0:1 ?
My setup is as follows,
Machine-1
- Two network interface cards on same network with different MAC say MAC-1 and MAC-2
- IP 10.209.193.130 and 10.209.193.131
- Firewall IP tables empty iptables -F
Machine-2
- One NIC with IP 10.209.193.135
switch
- both machines are connected to common switch and can ping happily.
Problem:
when I send ping request from Machine-2 to Machine-1 arp tables are initialized for IP MAC pair. Surprisingly both IP are get resolved to one MAC i.e MAC-1. general observation is, MAC of first interface which has route in kernel route table. I cross checked this on Suse11 and RHEL5 same result. but In suse10 I am getting expected behavior [i.e IP1-MAC1 and IP2-MAC2 pair in arp cache]. Do any one know why kernel is using same NIC for two different interfaces?
Output for Suse11 and RHEL 5
Code: ? (10.209.193.131) at 00:0c:29:34:e7:6f [ether] on eth3
? (10.209.193.130) at 00:0c:29:34:e7:6f [ether] on eth3 Output for Suse10
Code: ? (10.209.193.128) at 00:0c:29:02:9a:7c [ether] on eth3 <-------- Suse 10 machine-1
? (10.209.193.131) at 00:0c:29:34:e7:6f [ether] on eth3
? (10.209.193.127) at 00:0c:29:02:9a:72 [ether] on eth3 <-------- Suse 10 machine-2
? (10.209.192.1) at 00:00:0c:07:ac:07 [ether] on eth3
I'm running a fresh install on an intel i7 system on an asus p6t deluxe v2 motherboard with the onboard NIC (Marvell Technology pci-e). I know the NIC is working as when I boot into the onboard OS that Asus provides (Asus Express Gate SSD)I have a working net connection.Booting up CentOS hangs at determining IP information for eth0 and eventually fails with the following error:PING xxx.170.30.1 from xxx.170.31.231 eth0: 56(84) bytes of data---xxx.170.30.1 ping statistics ---4 packets transmitted, o received, +3 errors, 100% packet loss, time 2999ms, pipe 3 failed.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
[code]....
I am curious of how to make a GUI interface that uses multiple programs and commands. I have found wxwidgets as the most likely candidate for making my own interface.Is this the best programming language for a beginner?
View 3 Replies View RelatedI am having some troubles using iptable rules on two Servers that act as Gateways pointed to one backend server with only one interface.
To be more exact, i have 3 Servers, 2 of those have a public and a private interface, with different public ips but common private interface ( they connect to the same switch ), the last one only has 1 private interface and is connected to that same switch.
Those 2 servers also act as a gateway and a firewall for the private network.
My problem is that i cannot seem able to route traffic from both of those to the third one and back to the same public ip that the request came from ( effectivly using two gateways on the machine with only one interface ).
As a testing scenario i am using ferm for applying iptable rules that forward ssh traffic ( for example ) to the backend server, and it works well when i do it with one gateway.
When i apply something like this in /etc/network/interfaces on the backend server though:
Code: Select allauto eth0:0 eth0:1
# The primary network interface
allow-hotplug eth0
iface eth0:1 inet static
address 192.168.9X.XXX
netmask 255.255.255.0
broadcast 192.168.9X.255
network 192.168.9X.0
[Code] ....
Even though forcing selection of an interface from the backend server ( like curl --interface ) seems to work well, meaning that the request to the curl appear to happen from the correct public ip, i can still only use one of the public ips to access the server with the ferm rules. Ideally i should be able to ssh to the backend server from both public ips using their ferm rules for forwarding traffic to the backend server.
I feel like i am missing some details on routing that should happen on the firewalls as the backend server seems to be able to use both gateways to access the internet and receive replies from it.
I want to configure multiple virtual ethernet interfaces over a single physical ethernet interface (eth0) and for each virtual interface the MAC address must be unique and the IP address must be Static.Finally all the virtual interfaces must be able to communicate both internally and externally and the traffic should be captured using wireshark.
I need to have such kind of setup to communicate devices individually using one physical ethernet device.
Because I was fiddling with few kernel modules like MACVLAN and MACVTAP and successfully enabled those modules and rebuild kernel. Using macvlan and macvtap I can configure virtual interfaces with unique mac address and static IPs but while capturing packets using wireshark interfaces behave weirdly.
For example say on HOST machine I have 1 physical interface and created 3 virtual interfaces as shown below.
Interfaces :
eth0 (physical ethernet interface)
IP: 192.168.A.A
MAC: aa:aa:aa:aa:aa:aa
[Code] ....
First from above interfaces I started pinging eth0 internally from host machine in which it worked as usually.
Second I did same externally from other machine which is connected to the same network of Host machine, and this did work as usually.
Third I pinged first virtual interface veth0 both internally and externally and this also works and after that I did check source and destination MAC address using wireshark tool-where both showed up there respective MAC address.
Now triggers the issue, where I pinged second virtual interface same like I did for first one, but this time ping was success and where as in wireshark tool the MAC address for veth0 is picked by veth1. This is where I got stuck and this issue happened for all the remaining virtual interfaces.
I couldn't see any virtual interface showing their respective MAC address, as of the remaining except the first virtual interface has been picking the first veth0 mac address.
I have an old pentium 3 computer that has ~7 NICs installed. These NICs are attached to modems and other networking equipment. According to the linux ping page on computerhope.com, it seems that one could send a ping from a certain specified NIC. How would one go about this?
View 6 Replies View RelatedI have a CentOS 5.3 box with three network interfaces in it. Each interface is attached to a separate VLAN and I want traffic to stay on each network segment.What I can�t figure out is why I cannot get each interface to have its own gateway and everything gets sent through the default gateway.The basically takes my possible 3Gb total bandwidth and throws it down a single 1Gb pipe.Then on top of that, if I take down the interface (ifdown) that has the current default gateway,I loose contact to the other two interfaces.When I look at the routes, each one of the interfaces shows the gw as 0.0.0.0 and defers to the default route. So I delete the route and try to add a new route with:
[root@testsan ~]# ip route add 10.1.15.0/24 via 10.1.15.1 dev eth2
but end up with the error:
RTNETLINK answers: Network is unreachable
[root@testsan sysconfig]# cat network
NETWORKING=yes
NETWORKING_IPV6=no[code].....
I have a script I only want to run when a window is being dragged around. Is there an environmental variable or something that will tell me whether one is moving and which one it is? I'm using Ubuntu Lucid if it matters.
View 9 Replies View RelatedUsing a Linux program to fix my TiVo. Program is burned to a bootable CD, which loads fine. I get asked what the drives are (CD and Hard Disk) with abbreviations like hda, sda, etc. I was able to determine the Hard Drive as /dev/sda, by using <Shift>-PgUp/PgDn, but could not find what the CD drive was.
View 1 Replies View RelatedI have and embedded system which apparently, due to space considerations, is missing lots of normal commands. I can get the following information by "cat /proc/version":
Linux version 2.4.19-uc0 (...) (gcc version 2.95.3 20010315 (release)(ColdFire patches - 20010318 from http://fiddes.net/coldfire/)(-msep-data patches)) #461 Tue May 24 12:06:06 PDT 2011
At issue is the fact that, after some time, the system stops responding to the Network (e.g., you can ping it, then some time later you can't). We suspect that some sort of network monitor is accessing the device and causing the trouble, but don't know for sure.
What I would like to do is log some sort of useful network status information and/or be able to reset the network if I can figure out there is an issue from within the device.
I thought I had it all working using "/etc/init.d/network restart" but I've come to find out that the command is not recognised in this system. I also can't issue a "top" command to see what services are running. I can Telnet in, so I can try commands and see if they work.
Have any of you worked with such an abbr. system and if so, what might be around that I'm unaware of to help determine network status?
This questions pertains mainly to building a brand new GNU toolchain on one machine for deployment on fs of another machine that has no toolchain installed. I understand the machine on which GNU toolchain is going to be built as the 'build' machine. I understand the machine on which GNU toolchain is going to be deployed as the 'host' machine. I understand the machine on which the code generated by the new GNU toolchain is going to be run as the 'target' machine.
Q1.) Is there a fixed 'rule', 'matrix' or 'table' somewhere which tells me exactly which versions of 'binutils' and 'libc' are required by a particular version of GCC? I.e. something along the lines of:
- gcc ver.'k' can be built using gcc ver.'m'(or later) with binutils ver.'i' and libc ver. 'j'
- gcc ver.'k' will operate with binutils ver.'t' and libc ver.'r'(or later)
Is there some 'rule of thumb' / 'heuristics' giving me the above version requirements for the building and operating GCC, or is this information somehow implied or derived systematically. Where can I find more about the above?
Q2) I assume that the libraries have no dependencies on any underlying software other than the system calls provided by the kernel. Furthermore it appears that the libraries are not too sensitive about the kernel version they run on (I found this out from experience). Therefore I could build the libraries on some build machine and place them on the bare naked newly set up host file system without regard to any other prerequisite SW components?
Q3) During operation, do GCC and its various components place system calls directly to the kernel or via library calls (or both)? In other words I am trying to understand conceptually if GCC requires 'Glibc' for its own operation or not?
Q4) During operation, do the 'binutils' components place system calls directly to the kernel or via library calls (or both)? In other words I am trying to understand conceptually if the 'binutils' require 'Glibc' for their operation or not? ( Of course it is clear to me that when GCC is operating it will need libraries and headers to resolve object references in the target code it produces, but that would be a >different< question).
I am trying to scroll text from a text file across a wx.panel. This is the code so far:
Code:
def scrolling(self, text, rate):
def scroll(): charList = []
dc = wx.ClientDC(self.panel_1)
open_text = open(text, "rb")
my_text = open_text.read()
charList.append(my_text) open_text.close()
x,y = self.panel_1.GetClientSizeTuple()
while 1: for z in charList: for r in range(2000):
dc.DrawText(z,x-r,0) time.sleep(rate) dc.Clear()
net3 = threading.Thread(target=scroll)
net3.setDaemon(1) net3.start()
It scrolls but I am guessing where the range is (2000). I need to be able to determine the total number of pixels that the text in the file is. Is there a python way to determine this?
I ran the 11.04 upgrade. At the end, it reported a failure, implied a recovery would occur and the upgrade then finished. The recovery was supposed to have run sudo dpkg --configure -a. That does not appear to have happened. I am concerned that a reboot will render my system inoperative.Has anyone else experienced a similar issue or have any suggestions? What information should I provide. report.
View 2 Replies View RelatedIn my project i cannot determine the number of check list initially. I will know dynamically during execution.How to specify the number of check list dynamically in zenity.
View 5 Replies View RelatedI have a Dell Inspiron 1545 with Ubuntu Karmic that was working like a charm until last week.When I'm using my college's wireless I can browse just fine, but when I'm in my home's network the web addresses cannot be resolved.I was suspecting of DNS error, but it's the same DNS address in all the other computers, and the whole network is working just fine.The thing is that if I use the IPs, for instance 64.233.163.104 for Google, it works fine, both pinging and browsing. So the problem is in resolving the addresses...
View 9 Replies View RelatedMy Firestarter logs show periodic outgoing connection attempts to IP addresses in countries such as Malaysia, China, Russian Federation etc... Fortunately, Firestarter appears to be blocking them. I suspect these are not good and want to find out exactly what process is initiating these outgoing connections.
View 6 Replies View Related