I am looking for a command which, when typed from the command line, returns the ip-addresses of the DNS nameservers that my ISP is using.I think is should be technically possible to write a program that does this, because linux installers set up /etc/resolv.conf correctly (as does knoppix). But I've been unable to find a command that does it. Is there one, and if so, what is it called?
View 14 Replies
I'm running a dual boot system at work. I'm connected to a few shared drives in XP, and would also like to connect to them while using Ubuntu.How do I determine the addresses of the servers I'm connected (mapped) to in XP?
View 2 Replies View RelatedI have a CentOS5 server with dual ethernet adapters + Webmin installed as my Router / Firewall / DHCP server working successfully with 1 static IP from my ISP. I also have 7 additional static IP addresses from my ISP needing to configure to individual servers inside my network. I have configured the additional virtual interfaces, but am lost on how to route data specifically from additional ISP address to specific internal network address.
Below is my desired configuration.
98.173.159.xx1 = eth0 physical interface ==> eth1 192.168.1.1
98.173.159.xx2 = eth0:1 virtual interface ==> 192.168.1.10 ==> CentOS Server 2
98.173.159.xx3 = eth0:2 virtual interface ==> 192.168.1.20 ==> CentOS Server 3
98.173.159.xx4 = eth0:3 virtual interface ==> 192.168.1.30 ==> CentOS Server 4
98.173.159.xx5 = eth0:4 virtual interface ==> 192.168.1.40 ==> Mac OS X Server 1
98.173.159.xx6 = eth0:5 virtual interface ==> 192.168.1.50 ==> Mac OS X Server 1
98.173.159.xx7 = eth0:6 virtual interface ==> 192.168.1.60 ==> Network Attached Storage Server 1
98.173.159.xx8 = eth0:7 virtual interface ==> 192.168.1.70 ==> Windows 2008 Server 1
I am having an issue on my server where I can't access certain ip's erratically. These addresses could previously connect to us.I think it may be related to getting rootkitted. I know the risks in not reinstalling but we are not able to install yet at this point. I cleaned out shv4 and shv5 from the os and setup tripwire. The client can't ping the server and likewise back.From my personal computer they both respond to pings.The server is running denyhosts but that is about it in-terms of security.I can't find anyhting anywhere... No ipchains present, nothing in host.deny, subnet is 255.255.255.0.I'm really at a loss so I'm looking for some direction
I know someone is going to tell me that I have to assume all my files are compromised and i should reinstall; I did md5 checks on alot of files and there is no data on here that shouldnt get out and I check for stuff running that shouldn't be daily.The server is 10.04 server. Latest updates.Here is a list of installed packages
Code:
adduserinstall
anacroninstall
[code]...
Does anyone know the ubuntu update servers IP addresses. I am trying to fine tune my firewall rules and was unsure of what ip addresses to use for the update servers. I believe they are us.archive.ubuntu.com and security.ubuntu.com. However, I could be wrong.
View 3 Replies View RelatedI installed Apache by using the following command:
Code:
sudo apt-get install apache2
I later realized that there are two (or more versions) of Apache, MPM Worker (threadsafe) and Prefork. Since I'm trying to get both Tomcat and PHP working on the same system I need to know what version is installed of Apache, Worker or Prefork?
Looking in the package documentation, it said something about a virtual package... Looking inthe mods-enable directory, I don't see anything that indicates one or the other.
I'm also wondering if Tomcat integration can work with prefork?
I'm using Ubuntu 10.4 box with Apache2 web server. I have a site with several Domain Names. How do I set up tracking?
View 1 Replies View RelatedI want to display the associated host name with each address.
I've found the /var/lib/dhcp3/dhcpd.leases file, but it appears to have an entry for every time a lease was issued so it's hard to tell which ones are currently active.
when I try to access [URL]... I get an exception:
[code]...
I believe I need to change some directory permissions, but I can't determine exactly what.
I have a headless server set up with no GUI on board.I know there is some way to display the installed hardware , I just can't remember how.What I'm looking for in particular is determine the type and speed of the PCI-e slots.
View 2 Replies View RelatedI have tried several places for help but I am getting no where...Here is my background.I have spent all weekend to replicate my development server back at home. I have an Apache remote server with 3 IP based virtual hosts pointing to
[URL]
Now I have been able to set up a VM on my desktop, installed the OS, the applications, the db server, apache etc. Everything is looking good so far. So right now I have,
[URL]
So when I go to 192.168.0.111, I go to [URL] so I guess apache is working aswell.What I want to do is, instead of going to [URL] I want to change it to another address such as a.me.add1How can I do this? I am looking through the virtual hosts section, I have changed server name entry etc but its not working.Can you tell me in big picture what I would need to do to set that up? My current set up doesnt really help me much once the site get the www address.tell me if Document Root of IP address 192.168.0.111 points to [URL] will it always resolve into that webaddress. That is if I enter 192.168.0.111 the browser will redirect it to [URL].
I'm in the process of setting up a script in perl to make 1,000's of curl calls to my companies application on our test server. Our software does all sorts of tracking of data based on IP addresses using geoIP, so i was wondering if anyone knew of a way to fake these addresses to the server?I know a big issue with the IP faking is the return path but i dont really need this. I also cant do it on the hardware level since the script is going to be picking lots of different IP's at random.Anyone have any idea if this is possible and if so, are there any known libraries i can use for this? I prefer perl but any Linux compatiblie scripting language is fine.
View 1 Replies View RelatedHow do I put the FQDN in the etc/hosts file, server ip is 192.168.2.101 hostname - promisedland fqdn - promisedland.dyndns.org I just want to set up a web based file server. Here is what i put in hosts (/etc)-gedit
[Code]...
My Firestarter logs show periodic outgoing connection attempts to IP addresses in countries such as Malaysia, China, Russian Federation etc... Fortunately, Firestarter appears to be blocking them. I suspect these are not good and want to find out exactly what process is initiating these outgoing connections.
View 6 Replies View RelatedThis is the current setup that we have: We have approx 20 clients who pay us to send out a type of e-mail called an E-Blast to their customers. We currently are using 5 Microsoft Windows Virtual Servers to do this. The problem is that those machines are starting to break down. There are times that it will take Microsoft Windows approx 9-10 hours to complete 1 job. This is way too long. We want to move away from Microsoft Windows for this particular type of job as it seems there are more customers who are wanting to use this type of advertising.
It seems that using a Linux Server "Command Line or Shell" environment would be the best way to go as there is no GUI like Windows. Since there is just text...that is something that would/should process very, very quickly.
I am in the process of setting up a new SMTP outbound mail server. This is the current software & configuration (what is installed on this new machine):
All of the customer data (Names, E-Mail Addresses, etc that these e-mails are going to) are currently loaded in a Microsoft SQL Database.
My machine that I am using is plugged into the DMZ. I have 1 ip address for the 1 network card. I have also added/bound 4 more ip addresses to that network card.
I have configured Postfix for Multiple IP Addresses.
I can, from the command line, send successful test e-mails and receive them in my personal account.
As far as I know everything is setup correctly. I can and will post requested information so that it can be verified that everything is setup correctly.
Here are a couple of my questions:
Ensure that I have my Network / Interfaces file and my Postfix's Master.cf/Main.cf files setup correctly?
How can I setup this server to be an Outbound SMTP server and get it to use all 5 of the IP Addresses to send these e-mails quickly?
What can I use to check and ensure that this server is in fact sending out emails on all 5 IP
Addresses (I heard that there is a program named "Postal" that may help in determing this).
Does anyone know a good program to log ip addresses when visited or connecting to your machine? Something like tcpdump but for ip addresses, I forgot what its called.
View 3 Replies View RelatedIs it possible to configure two IP addresses using one NIC? I'm implementing a VPN server on network 192.168.1.0, ultimately to be accessed over the Internet and through an ADSL router with port-forwarding to the server. Right now I'd like to test it on the LAN, but with the VPN client and server both on the 192.168.1.0 network, that test would not be be valid.
If I had a spare NIC I could put the server on both the 192.168.1.0 network and, say, a 10.0.0.0 network, configure the client on 10.0.0.0 and test. Not having a spare NIC, I'm wondering if it is possible to configure the server with two IP addressese NIC.Virtualising hosts are able to do something similar when running guests with NICs in bridged mode. Log files show they switch eth0 into promiscuouse.In case it matters the server OS is Slackware 13.0.
Can I set 2 addresses for the *1* Ethernet card that I have on my motherboard? How would this scenario work?
View 5 Replies View RelatedI've used two internet services to show me my IP address, and I get different results:1. Whatsmyip.org : ***.**.109.***2. ipchicken.com : ***.**.111.***All the * numbers are same, except 109 and 111. (or link me to explanation) of which one's which?
View 8 Replies View RelatedHow can I get two ip addresses to communicate with each other which are not in the same 255 range?
Like:
192.168.0.1
and
192.168.1.1
My machine has ONE ethernet card and is on a LAN.IP address is assigned to hosts using DHCP.I can have more than one MAC address on LAN by running Virtual Machine and setting network to bridged. This way, my virtual machine simply acts like there is one more machine in the network.Running VMWare for this job is a a bit heavy on resources. Is there a way so that I can I can have 2 or more ip addresses with different MAC address on the same machine without having to run VirtualBox.
By googling, I think its related to bridging and tap. And, I am sure thatts NOT IP-ALIASING because in ip-aliasing both the ip addresses have the same MAC address.Basically, I want my system to have interfaces like:-eth0 - which was originally presentlo- thats always present :|newint0 - New interface with new MAC address and IP addresses which can access my LAN directly. Its like if I bind, let us suppose curl to this interface, its like a different connection
i want to change the mtu size of my ethernet controller. I have done successfully set the mtu size 9000 for broadcom net xtreme PCI: 66 Mhz 64 bit 1 gigabit card. (fibre)
Part model no: BCM95703A31
[root@lux08 ~]# ethtool eth0Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
[Code]....
how to change the mtu size for this NIC?
I have connected my computer to network. Computers in network have dynamic ip address which is assigned by ADSL modem's DHCP. Besides this I want to have static IP address for same NIC. So is it possible to have both static and dynamic IP address for single NIC? If so how can I assign it using command and also in GUI?
View 7 Replies View RelatedI have a Dell Inspiron 1545 with Ubuntu Karmic that was working like a charm until last week.When I'm using my college's wireless I can browse just fine, but when I'm in my home's network the web addresses cannot be resolved.I was suspecting of DNS error, but it's the same DNS address in all the other computers, and the whole network is working just fine.The thing is that if I use the IPs, for instance 64.233.163.104 for Google, it works fine, both pinging and browsing. So the problem is in resolving the addresses...
View 9 Replies View RelatedI am running a dual boot PC, Ubuntu 10.10 & Win7. I do sticky static IPs on my local network, but it doesn't work cause the Ethernet adapter gets a different MAC address in Windows 7 (EF:9F:E9:F7:F7:F7) than it shows for Ubuntu 10.10 (00:13:74:00:5C:3. I am not sure if this is a Windows problem or something up with Ubuntu. The card is an on-board Atheros L2 fast Ethernet adapter. I have tried updating the drivers in Windows & nothing is working.
View 8 Replies View RelatedI would like to know if a rule has been applied to the iptables.active file to accept direct connections on port 22 through an IP address, can I also add a mac address/addresses to the rules such that if I am not on the network with the accepting IP address, that my MAC address will still get me in?
View 4 Replies View RelatedI would like have a password for accessing my web site which works fine. I also want for the specific site to allow access only for a specific range of ips. Right now the following config should forbid my access, as my ip is different from 200.200.200.*
View 6 Replies View RelatedI do not currently fully understand relationship between binary numbers and ip addresses and subnet addresses; nor am I asking for an explanation here at LQ, when there are plenty at wikipedia and other places...
Even after reading the wikipedia article on it, I still don't grasp it completely, so I was hoping that someone who grasps it in its entirety could answer a simple question.
How can I express the range of ip addresses from 172.22.22.200 - 172.22.22.230 ?
I was trying to make a rule for iptables that only did nat on that specific range of ips, and when i tried used the "-s" flag followed by 172.22.22.200/11 it always changes to 172.0.0.0/11 in the actual rule that is created and displayed by iptables -t nat -L.
I already have many hosts defined on my network, and rather than going through each one and changing its ipaddress to 172.0.0.#, I was hoping to learn a way to represent them in the iptables rule.
I am using DHCP on my home network. There could be as many as 5 computers logged in at any given time. Their IP addresses change depending on the sequence they log in.I want to be able to connect to them from any of them (some wired, some wireless) and share files by issuing a mount command for the appropriate shared drive.My question is how to get the IP of each computer when I only know the names of the computers. Pinging the computer name succeeds, but it does not give the IP.In other words I am looking for a Linux command that will come back with a list of IP's with their corresponding computer names so I can issue the right mount command. I would like to issue this command from a Linux terminal, but would also be happy to issue it from a Windows XP station.
View 14 Replies View RelatedI'm on Fedora core 14 linux. and I'm online with the HSPDA modem. My modem is /dev/ttyUSB0 and when it's dialed it creates the interface /dev/ppp0 , My question is when I hit ifcofig it shows two IP addresses in the ppp0 interface.
Code:
[nature@localhost ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 20:6A:8A:12:CF:53
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]....
when I get the routing table, the gateway is setten to the 10.64.64.64 and when I look my Ip address global I found it's 175.157.64.119.
