General :: List All Wireless Points - Frequency?
Sep 17, 2010How can I list all stations with frequency they are at ?
View 1 RepliesHow can I list all stations with frequency they are at ?
View 1 RepliesIs there a CLI command or program that will list available wireless access points? I'm running Ubuntu 9.04 on a laptop and sometimes I boot straight into the CLI instead of a GUI. I know iwconfig can configure a connection but will not list available AP's.
View 5 Replies View RelatedHow can I go about seeing the different AP around me using the terminal?
OpenSuse linux
I have wireless G and N access points in my house. The N network is set to allow only N connections. I have a Lenovo laptop with a Intel Wireless N chip in it, and after one of the 10.10 updates it stopped connecting to my N access point. The G access point works just fine.
The logs for the Wireless N access point alway show "Bas Password." I am having the same problem with either NetworkManager or wicd.
Installed 10.10 maverick on my compaq mini 110, activated the restricted STA driver... But under the networking drop down it shows wireless as enabled but I cannot actually see any networks, there should be about a half a dozen to see. Works fine under windows. Before the restricted drivers are activated ifconfig shows eth0 and after eth0 and eth1 but when I do iwscan eth0 or eth1 it tells me this action is not supported! I have tried reinstalling from cli but no difference?
View 3 Replies View RelatedI am having trouble connecting to 1 particular wireless hotspot. It used to work in Ubuntu 10.10, but after upgrading to Ubuntu 11.04 it sees the Access Point, tries to connect but never succeeds. I can however still connect to my home router. Both use WPA2, both have a good signal. I have an ASUS UL30a laptop with a (output from lspci): Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) NIC I was thinking of installing the linux-modules-backport-net package?
View 1 Replies View RelatedI have two wireless access points in my home network. A Linksys upstairs and a Watchguard Firebox downstairs. The Firebox acts as the gateway for my network to the internet (well, the ISP's router anyway). I invariably use my Hardy Heron installed HP laptop downstairs, less than 10ft from the Firebox. The signal bar for the Firebox shows three bars, the linksys just one. So, why the heck does my Ubuntu insist on connecting to the Linksys everytime?! I can manually switch it afterward but still, it's annoying.
View 7 Replies View RelatedIs there away to view wireless access points without being connected. I am having trouble getting connected to my wireless DSL modem. I have no problems connecting with Windows Vista. Just can not get Ubuntu 9.10 to connect. iwconfig says no associated with access point. I can connect with ethernet cable.
View 3 Replies View RelatedI have just upgraded my system to Fedora 14. One thing I noticed after running some applications on it is that it is not possible anymore to figure out on what frequency a wireless interface is using. If I set a wireless interface to monitor mode and perform the iwconfig or iwlist command, in the past, I could see the frequency used on the interface, but now, this information is not present anymore. My wireless interfaces are in monitor mode.
Has the frequency information been removed from iwconfig or iwlist commands? If it has, is there another way to report this information?
Here is an output from iwconfig on my system:
I'm not exactly sure if this should be here and not in the Hardware & Laptops section, but seeing as my only problem is with WiFi, I'm guessing this is the right place. Under Ubuntu, my laptop (an Asus K42Ja, more details below) can see wireless networks normally. However, when I attempt to connect, it fails to establish a connection. Under Windows on the same laptop (dual boot), no problems are experienced.
According to this, there's a firmware bug in my wireless chip which causes connections to get dropped. I'm not getting connections at all, but I still tried the workarounds on that page with no luck. The router is a TP-Link TL-WR340G. My previous laptop, a really old one from 2003 running Ubuntu 9.10 was able to connect to that router without problems. The wireless card was Intel on that as well (but, of course, much older). The router is set up to use WPA for security. I didn't use WPA2 as I read something a while ago about problems with WPA2 and some Linux distros. Please correct me if I'm wrong here.
If anyone's curious, I'm posting this on Ubuntu, via an ethernet cable to the router mentioned earlier. Some tasty technical bits: dmesg (the latter half of the "timed out" messages is me retrying after double-checking the WPA key)
[Code]....
I used to use Ubuntu 10.04. Never had this problem. I went back to Windows 7 and then came back to Ubuntu, and 10.04.1 was released. After some usage of wireless internet, it disconnects from the access point, and phy0 has 100% usage. [URL].. I'm not the only one with the problem. I downgraded to 9.10, and haven't had that problem since the downgrade.
View 1 Replies View RelatedI can connect to my school's wireless network using the standard network manager, but often (not always) it repeatedly disconnects and reconnects every few minutes. Occasionally it also prompts me for the security information again (even after it previously connected successfully).
By running iwconfig when it's on the fritz, I can see that it's often switching access points for the network - which is what I think is causing the problem. It disconnects and reconnects even when the signal strength for the current AP is fine, and it will often switch to an AP with a weaker signal strength.
$sudo lshw -C network
Code:
description: Wireless interface
product: Realtek Semiconductor Co., Ltd.
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:05:00.0
logical name: wlan0
[Code]...
When I install Ubuntu 9.04 the wireless works fine on my Toshiba Satellite. However, when I let the update manager update to the newest things the wireless doesn't even show up as a choice, as if the wireless card isn't installed. The drop down menu from the network icon only has wired on the list and I can't seem to find anywhere to set the wireless as existing. The same thing happens when I install a new version of Ubuntu 9.10. It just doesn't seem to be there. If anyone knows why this is or how I can fix it it would be greatly appreciated. If you need any more info from me just let me know.
View 3 Replies View RelatedI recently read over here: Getting Your Wireless to Work : "For example, open-source firmware for the Broadcom BCM4306/3 BCM4318, and BCM4311/1 was just released. Future openSUSE versions will be able to include this firmware and those devices will work immediately..." I am looking for PCI cards for desktops. Besides the list of supported chipsets at [URL], is there a brand name list with firmware support by OSS 11.3? At the moment, I have a Netgear WG311v3 which believe has been causing system instabilities in both linux and windoze:
01:06.0 Ethernet Controller [0200]: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11 b/g Wireless [11ab:1faa] (rev 03)
I 've a question regarding which points should be considered to compare 2 different linux distros say RedHat & Ubuntu. for a production environment non-db applications ..
View 3 Replies View RelatedI have recently started to use linux, ubuntu to be specific, and I'm already starting to receive grief from my mac-fanboy and windows-fanboy friends. Aside from the increased speed of the OS, and small size, what are some things I can do to prove the advantages of linux to them?
View 14 Replies View Relatedi want to have 2 partitions. one is called system. the other is private.
in the private partition i've got some folders i want to mount into system as system folders.
folders in private:
- www
- home
mount points in system:
- /var/www
- /home
is this possible? cause it seems that you can only specify a whole partition to use for a mount point and not a folder in a partition or am i wrong?
i run ubuntu server.
When I insert an SD card in the reader, slackware creates a mount point and mounts my card volumes. On unmounting the volumes, the mount point vanishes. How do I achieve this manually?When I attempt to mount a volume using the mount command, the mount point folder must exist and the folder does not vanish on umount. Is there a way to create a mount point if it does not exist? and ensure that the folders vanish on umounting?
View 2 Replies View RelatedI would like to know how to show all the current mount points in the file system. I tried mount but it didn't show the nfs mount point.
View 5 Replies View RelatedComing from non linux bod - but to create mount points on nas that are visible do we have to put entries in both fstab and rc.local?
View 1 Replies View Relatedfigure out the best partition layout for my linux installation which I'm about to have on my laptop. Having read numerous articles on partitioning in linux I've gathered some ideas, still there was no let's say a clear explanation as to the sequence the mount points should be arranged on the disc...What I have in mind is to use a single disc space as efficiently as possible considering the head travel. The pc is a laptop, 160GB HDD and will be used as a normal desktop with some simple sound processing. Distro Linux Mint 10. I'm planning to have such partitions and all will come after a Win7 installation:
/boot -> some write it's not necessary in dual-booting, some that it's good to have for security
swap -> with 4GB of RAM i don't suppose i'll use it
/
[code]....
have the most heavily utilised partitions close to each other so the head doesn't move for large distances. The placement also makes a difference as the closer to the inner rim of the disc the worse performance. I'm also not sure about the sizes. Read posts with recommendations but still judging by installations on a different laptop and virtual machine e.g. 5GB for /opt is a bit too much as there's almost nothing in there. Certainly /usr fills up, /var too from what I've observed. / also has scarce data in it so I'm wondering if giving them e.g. 5 gigs each won't be a waste of space resulting in greater head travel.
I have bought a new motherboard (MSI 785GT-E63). I already have an old CRT monitor connected to it. After I install a linux OS to it, my monitor will display that it is:
Out of frequency.
Current frequency is 89Hz. The
operating output of my monitor is
(around) 60-70Hz.
I would like to get this thing work. How can I let my CRT display properly?I was thinking of lowering down video frequency output of my motherboard, but I can't find any settings on my BIOS setup. Additional info:
My monitor is attached directly to
the built-in video adaptor of my
motherboard. (No additional video
[code]....
Each time I start up debian -lenny, the network-manager does not automatically connect me to my wireless network. The connection list shows a lot of networks available, but mine is always absent from the list. This means I each time have to go to "Connect to other Wireless Network" in and write in my network name (SSID) and password (PWA2 Personal). Then is connects nicely and everything works fine until next time I boot
View 5 Replies View RelatedHow can I convert a file with a lot hex numbers into the decimal?
Example: file1
0x59999
0x5acdc
0xffeff
I want to start $ cat file1 | util | cat >file2 and get file2 with smth like
[Code]...
Is it possible to use network storage locations as mount points during installation?
cause i want to separate system (ubuntu) with data (personal files).
eg. if i have 5 computers i don't want to recreate /home/david 5 times.
so i want to mount networkdrive/home to /home in local ubuntu server.
so ALL users home folders could be used and maybe also networkdrive/projects to /projects.
in that way its ok if i by accident repartitioned the local ubuntu server cause all data is not there on that server, but in the data server.
is separating "data" from "logic" good in this case?
and is it possible? what protocol should i use for the mapping over internet? (maybe the server is in Sweden, and the data is in Norway).
I try to mount one disk image to two points.
sudo mount -o loop,user,uid=dm /home/dm/mmm/test_drive1.img /home/dm/mmm/fs
sudo mount -o loop,user,uid=dm /home/dm/mmm/test_drive1.img /home/dm/mmm/fs2
Thats done
But when i create,copy or change anything on one mount point (../fs) its not updates on second mount point (../fs2).
Does anyone know way to 'share' one disk image (.img) to some mount points?
1. What difference will it make if I set the mount point to "/" instead of "/boot" and vice-versa ?
2. I heard somewhere that the data on a primary partition can be easily recovered in case of some failure.
If it is so then what out of the following should IDEALLY be created as primary partition ?
/usr
/home
/boot
I think /usr and /home both need a primary partition , then what about /boot, Will I be not able to recover something in case of failure if I don't set /boot as a primary partition ?
How can I check to which file a given symbolic link points?
View 2 Replies View RelatedI want to change the display's frequency from 60hz to 50hz, on a fedora core 9 box, anyone know how to do this?
View 2 Replies View RelatedI have configured a wireless pcmcia card using ndiswrapper. I'm sure that works, as with the command "iwlist wlan0 scan" gives me back
the list of detected wireless networks. At this point I was wondering: is there a way to detect the new interface (wlan0) with network manager? Even after enabling the wifi card the network manager gnome applet always finds only eth0.