General :: Debian Software RAID 1- Boot From Both Disk
Mar 15, 2011
I newly installed debian squeeze with software raid. The way I did was, as also given in this thread.
- I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap)
- I selected the hard drive and created a new partition table
- I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable.
- Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /.
- Created another partion and used for swap
Then RAID configuration:
Through Configure RAID menu -> create MD device ->
(2 for the number of drives, 0 for spare devices)
Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot)
Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /)
And no RAID for swap partitions
'Finish Partitioning and write changes to disk' --> Finish the rest of the install like normal. Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok.
View 2 Replies
ADVERTISEMENT
Sep 19, 2014
I am running a 14 disk RAID 6 on mdadm behind 2 LSI SAS2008's in JBOD mode (no HW raid) on Debian 7 in BIOS legacy mode.
Grub2 is dropping to a rescue shell complaining that "no such device" exists for "mduuid/b1c40379914e5d18dddb893b4dc5a28f".
Output from mdadm:
Code: Select all # mdadm -D /dev/md0
/dev/md0:
Version : 1.2
Creation Time : Wed Nov 7 17:06:02 2012
Raid Level : raid6
Array Size : 35160446976 (33531.62 GiB 36004.30 GB)
Used Dev Size : 2930037248 (2794.30 GiB 3000.36 GB)
Raid Devices : 14
[Code] ....
Output from blkid:
Code: Select all # blkid
/dev/md0: UUID="2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb" TYPE="xfs"
/dev/md/0: UUID="2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb" TYPE="xfs"
/dev/sdd2: UUID="b1c40379-914e-5d18-dddb-893b4dc5a28f" UUID_SUB="09a00673-c9c1-dc15-b792-f0226016a8a6" LABEL="media:0" TYPE="linux_raid_member"
[Code] ....
The UUID for md0 is `2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb` so I do not understand why grub insists on looking for `b1c40379914e5d18dddb893b4dc5a28f`.
**Here is the output from `bootinfoscript` 0.61. This contains alot of detailed information, and I couldn't find anything wrong with any of it: [URL] .....
During the grub rescue an `ls` shows the member disks and also shows `(md/0)` but if I try an `ls (md/0)` I get an unknown disk error. Trying an `ls` on any member device results in unknown filesystem. The filesystem on the md0 is XFS, and I assume the unknown filesystem is normal if its trying to read an individual disk instead of md0.
I have come close to losing my mind over this, I've tried uninstalling and reinstalling grub numerous times, `update-initramfs -u -k all` numerous times, `update-grub` numerous times, `grub-install` numerous times to all member disks without error, etc.
I even tried manually editing `grub.cfg` to replace all instances of `mduuid/b1c40379914e5d18dddb893b4dc5a28f` with `(md/0)` and then re-install grub, but the exact same error of no such device mduuid/b1c40379914e5d18dddb893b4dc5a28f still happened.
[URL] ....
One thing I noticed is it is only showing half the disks. I am not sure if this matters or is important or not, but one theory would be because there are two LSI cards physically in the machine.
This last screenshot was shown after I specifically altered grub.cfg to replace all instances of `mduuid/b1c40379914e5d18dddb893b4dc5a28f` with `mduuid/2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb` and then re-ran grub-install on all member drives. Where it is getting this old b1c* address I have no clue.
I even tried installing a SATA drive on /dev/sda, outside of the array, and installing grub on it and booting from it. Still, same identical error.
View 14 Replies
View Related
Oct 16, 2009
my Fedora 11 system is not starting anylonger. It stops with the message:
Code:
VFS: Can't find ext4 filesystem on dev dm-0
The system told me since a while, that a lot of the sectors of one disk of the (software) RAID compound are failed already. So tried to disconnect each of the disks and start them separately. Unfortunaltly this is not working (for one its is not working at all, the other wents the same far as with both), when I tried to recover the system with the Fedora DVD, it said no distribution found. I am quite new and do not know so much about linux system, so i do not know what further information you could need. Maybe it can be important, that both disks are encryped (the system wents so far, that I can type in the password).
View 2 Replies
View Related
Mar 28, 2010
I wanted to implement raid5 such that one partition is from my laptop's hard disk and others from other hard disks. After making one partition a raid partition, I rebooted the system. The computer stopped mid-way during booting, and brought me to the shell. On typing fsck -p, it told me an unexpected error occured in the partition which I had made for raid. Is there some condition that we cannot boot from a disk containing one of the raid partitions ?
View 1 Replies
View Related
Sep 3, 2010
I tried installing Ubuntu 10.04 WS on my PC but it did not see any disks to install on. I believe this is because my drives are all configured as RAID. My mobo is an Asus M3A78-EMH HDMI AM2+ socket with an Athlon 2X 5000+ CPU. The chipset is AMD 780G. I have the BIOS configured for RAID drives and I already run Win XP x32 and Win 7 x64 on it. My boot drive is configured as 'RAID READY' and I have 2 RAID 1 disks consisting of pairs of SATA drives.
From what I have researched it seems that with some tuning it should be possible to install Ubuntu 10.04 but I have little Linux experience and don't want to mess up my existing drives. I have installed Linux before a few times and run it but never with RAID. Is anyone aware of an existing disk image that I will be able to install from on my system or would it be possible for someone to create one for me to use?
View 4 Replies
View Related
Feb 23, 2010
I was running Ubuntu 9.04 Desktop on a headless Pentium 4 machine which is our file, mail, web & fax server. The two x 250GB SATA hard disks were in a RAID 1 array with full disk encryption. Ran the 9.10 upgrade via WEBMIN and it failed. I should have known then to copy over everything to a backup disk, but instead I rebooted.
On restart the machine accepted my encryption passphrase but promptly hung with a mountall symbol lookup error - code 127. So I can't start the machine to get at the disks, and using a Live CD is useless as it has no way to open the RAID array to get at the encrypted partitions. Although we have data backed up (as at last night) I'd hoped not to have to rebuild the entire server from scratch. But its looking bad.I have taken one drive out and plugged it into another machine (Hercules), and the partitions show up as /dev/sdb1 /dev/sdb2 /dev/sdb3.
If it weren't for RAID, I could open /dev/sdb2 the main partition) in Disk Utility and enter my encryption passphrase to get access. But RAID adds a layer of obstruction that I have not yet overcome. I used mdadm to scan the above partitions and created the /etc/mdadm.conf file, which I edited to show the 2nd drive as missing (rather than risk corrupting both drives). I activated the RAID array with mdadm, and cat shows:
Code:
root@HERCULES# cat /proc/mdstat
Personalities : [raid1]
md1 : active raid1 sdb3[0]
1815232 blocks [2/1] [U_]
[Code]...
I've been searching the web for hours but have yet to find someone with a solution to this situation. If anyone has a thought on how to access this disk I'd be pleased to hear from you. In the meantime I will start building a new (9.10) machine from scratch, without RAID, 'cos that's probably going to be necessary.
View 1 Replies
View Related
Feb 20, 2016
How can i get a RAID virtual image disk?
What i need is to mount several directories from any other partiton (or file system) as a new merge file system that can grow or decrease depending on the free space. As if it was a dinamic RAID,so i can work with huge files distributed over the partitions mounted.
Ejemp: /mnt/sda1/dir_raid1 + /home/dir_raid2 + /mnt/sda3/dir_raid3 ---> /mnt/RAID/
mhddfs and unionfs <---- are not the solution im searching (cant use huge files)
View 0 Replies
View Related
Aug 31, 2010
concerning Linux, mdadm, and creating RAID Array's in Debian. I've done a lot of reading and research on RAID both on this board and elsewhere (The Linux Documentation Project's Software-RAID HOWTO is especially good), but I've run across something that no one seems to explain, and I'm not sure why. I'm instructed to create partitions on the drives I wish to add to my array. These partitions inevitably take up the whole disk, and are always have their system IDs set to "Linux raid autodetect". What I don't understand is why, after creating these partitions, some guides then go on to create an array (say a RAID5 one) with just the disks themselves as members, while others go on to create the RAID5 array with the previously created partitions as members. E.g.,
mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 /dev/sda /dev/sdb /dev/sdc /dev/sdd
vs.
mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1
What's the advantage of using one over the other?
View 3 Replies
View Related
Aug 12, 2010
I've got an 8-disk raid-5 setup, and one of the disks failed. I shut the system down, replaced it, and powered the box back on again. Then, I made a catastrophic mistake; I 'failed' and removed the wrong disk (should have been sdj1, and I typed sdk1 by accident). I tried to re-add sdk1 back to the raid array, but it got listed as 'spare'. My raid array is off-line, since I now have 2 disks unavailable.
I know that the data still exists on sdk1, is there any way I can get the raid array to recognise the fact that it's a valid part of the array, and not a spare disk? At least if I can do that, I'll have a degraded but accessible array, and then I can rebuild the array on the properly replaced disk.
View 7 Replies
View Related
Feb 11, 2011
I have 2 identical disks originally configured as a pair for a server. Each of the disks has 2 partitions dev/sdb1,dev/sdb2. The sdb1 partitions I had configured as a raid1 mirror. The sdb2 partitions were non-raid and used as extra misc. Space. Further, the raid setup is also encrypted using dm-crypt luks. Now I want to redeploy each of the disks for new purposes. One of the disks i want to deploy exactly as before (keeping the partitions and content), however without being part of a raid array.
I've successfully deployed this disk into a new system and I am mounting the dev/sdb1 partition as dev/md0 because the disk is set to autodetect raid. Actually I am using cryptsetup and mounting with mapper. Can I get rid of the setting for auto detect on this partition without losing the data, or breaking the encryption? I just want to mount the partition as a standalone encrypted disk. Is it as simple as doing crypt setup luksOpen /dev/sdb1 then mounting it with mapper? Or do I need to change the partition in some way. Or do I simply continue to operate it as a 'broken' raid array?
View 2 Replies
View Related
May 4, 2010
I scored a Dell poweredge 6300 from a local pawn shop. It has the capability to boot from cd-rom, but apparently not with isolinux, which is what the debian installer cd uses. I was able to boot to UBCD411 (Ultimate Boot CD, which uses syslinux), but didn't see any option to boot to a CD (maybe I'm missing something here?). I tried using the boot floppy from this site. I didn't expect it to work (it's from the Woody era), and it did not. I got a message that says SYSLINUX ver.XXXX CBIOS boot failed. I went to [URL].. and looked for a boot floppy image for Lenny, but apparently it doesn't exist. I did however find the boot floppy image for Etch.
To be honest, even if I did find the Lenny floppy boot image, I'm not sure how to use it to point the system to the installer CD. So, I have two questions:
1) Does anyone know of a boot floppy image for Lenny, or if I could use the Etch boot floppy image?
2) How would one boot from floppy, then point the system to the installer CD?
System info:
(4) Xeon Pentium 2 processors 500 Mhz
(6) UltraSCSI hard drives
(1) SCSI cd-rom drive
(1) SCSI dvd-rom drive
(1) Floppy drive
(1) 10/100 NIC
I'm open to any other suggestions as to how I could install Debian Lenny on this machine.
View 5 Replies
View Related
Nov 3, 2015
I installed Debian on my PC with a Acer Stock motherboard (xc600) with amd64 and after the installation finished it told me to remove my installation media and reboot. After reboot I was returned this message ' ERROR: No boot disk has been detected or the disk has failed.'. I have verified with gparted using mint live OS that I have Debian installed on my system.
I got believes that this may have be caused by a broken grub or I need to configure something I don't know how in BIOS.
I will update the topic later..
My installation media was a USB 2.0 flashdrive with a Debian 8.2 Jessie Installer and 9 different Linux distros. I have installed Debian multiple times before on my laptop and never had this problem so I know how to go through the installation process and set the partitions.
View 3 Replies
View Related
Oct 27, 2010
I have a hypothetical situation in which I installed my operating system using a RAID1 mirror. At some point I decided that this setup was overkill, my machine isn't system critical, I value doubling my storage space more than speedy recovery, I'm doing routine backups, etc...
Short of backing up my system volume and repartitioning, or otherwise starting over, is there a way I can reconfigure my RAID1 array to only expect one disk so that mdadm no longer reports a Degraded state?
View 3 Replies
View Related
Aug 4, 2010
I want to build a 6xSATA RAID 5 system with on of the disks as spare disk. I think this give me a chance of 2 of 6 disks failing without losing data. I am right?
Hardware: Intel ICH10R
First I will creat a 3xSATA RAID 5, after I will add the spare disk and after that I will add the others disks. This is what I think I should do.
Step 1:
Create RAID Device
Code:
mdadm --create --verbose /dev/md0 --metadata 1.2 --level=5 --raid-devices=3 /dev/sda1 /dev/sdb1 /dev/sdc1
I read that "--metadata 1.2" is the best option. It is true?
Create filesystem on the RAID device
Using this method of calculation:
* chunk size = 128kB (for RAID 5)
* block size = 4kB (recommended for large files, and most of time)
* stride = chunk / block = 128kB / 4k = 32kB
* stripe-width = stride * ( (n disks in raid5) - 1 ) = 32kB * ( (5)- 1 ) = 32kB * 4 = 128kb
Then:
Code:
mkfs.ext3 -v -m .1 -b 4096 -E stride=32,stripe-width=128 /dev/md0
Step 2:
Add spare-disk
Code:
mdadm --add /dev/md0 /dev/sdd1
Is this enough?
Step 3:
Adding disks:
Code:
mdadm --add /dev/md0 /dev/sde1
mdadm --grow /dev/md0 --raid-devices=4
fsck.ext3 /dev/md0
resize2fs /dev/md0
View 1 Replies
View Related
Aug 12, 2010
I just configured two raid setups but after a reboot they are not mounted and seem to be inactive.
md127 = sde1, sdf1 and sdi1 (raid 5)
md0 = sda1 and sdh1 (raid 0)
Code:
root@server /]# cat /proc/mdstat
Personalities :
md127 : inactive sdf1[1](S) sde1[2](S)
78156032 blocks
md0 : inactive sda1[0](S)
488382977 blocks super 1.2
unused devices: <none>
Code:
[root@server /]# fdisk -l | grep "Disk /"
Disk /dev/sda: 500.1 GB, 500107862016 bytes
Disk /dev/sdb: 80.0 GB, 80026361856 bytes
Disk /dev/sdc: 122.9 GB, 122942324736 bytes
Disk /dev/sdd: 160.0 GB, 160041885696 bytes
Disk /dev/sde: 40.0 GB, 40020664320 bytes
Disk /dev/sdf: 40.0 GB, 40020664320 bytes
Disk /dev/sdg: 1500.3 GB, 1500301910016 bytes
Disk /dev/sdh: 251.0 GB, 251000193024 bytes
Disk /dev/sdi: 40.0 GB, 40020664320 bytes
Disk /dev/sdj: 500.1 GB, 500107862016 bytes
Code:
[root@server /]# cat /etc/mdadm.conf
DEVICE /dev/sdi1 /dev/sdf1 /dev/sde1 /dev/sda1 /dev/sdh1
ARRAY /dev/md127 UUID=5dc0cf7a:8c715104:04894333:532a878b auto=yes
ARRAY /dev/md0 UUID=65c49170:733df717:435e470b:3334ee94 auto=yes
As you can see they now show up as inactive. And for some reason sdi1 and sdh1 are not even listed. What can I do to get them back? To make matters worse I placed some important data on them, and even if I was clever enough to keep an extra copy on another drive, guess which drive that was? So, I need to get them activated as is (at least so I can get the data of them) before I can rebuild them from scratch. I'm running Mandriva 2010.1 and rated tehm using the built in disk partitioner.
View 14 Replies
View Related
Jan 21, 2011
For several days I stuck on a problem despite my various searches on the net. I just installed a machine in RC1 Squeeze.
My Partitioning
Disc 1
/ boot RAID 1
/ swap RAID 1 and encrypted
/ RAID 1 and encrypted
[Code]....
View 5 Replies
View Related
Nov 3, 2010
Purchased (4) 2TiB Drives (actual disk space) and created a RAID5 array expecting to have 6TB of useable disk space, however actual useable space is 5.46TiB.
So, the question is where did the disk space go?
First off, I can say for certainty the disks actual useable is verified at 2TB each have mounted and formated on a non-linux system (OSX).
Disks - 2TB Per disk, Tested HFS, Actual 2TB Useable
root@server:/server# fdisk -l 2>/dev/null | egrep "sd[hijk]" | grep Disk
Disk /dev/sdh: 2000.4 GB, 2000398934016 bytes
Disk /dev/sdj: 2000.4 GB, 2000398934016 bytes
Disk /dev/sdk: 2000.4 GB, 2000398934016 bytes
[Code]....
View 2 Replies
View Related
Apr 4, 2010
I have installed a Fedora Core 12 Linux system onto a RAID 1 file system. I now need a way of getting an notification if the disk fails. Is there an SNMP MIB that covers Intel RAID? I have done the searching but still the answer alludes me.
View 1 Replies
View Related
Dec 12, 2009
I have a 5 disk raid 5 array that is composed of SATA A:0,1; SATA B: 0,1, and SATA C:0, and one of the disks (SATA A:0) recently went bad on me. I have an ICP raid controller that is about 5 years old. I replaced SATA A:0. After rebooting, I went into the controller and verified that it saw the disk in the hard-disk info section...there I noticed that in the "status" section, that the SATA C:0, SATA B:1 disks were listed as being "in array", the SATA A disks were blank, and the SATA B:0 disk was listed as "fragment". When I go into the "repair array" section, the controller tells me that there are no arrays that are in failure, error, or need to be rebuilt.
This puzzles me, as I thought the controller would know that the array needs to be rebuilt after replacing the disk and I don't see a way to initiate a rebuild. If I just let the server boot after replacing the disk, then I get back that there are the correct number of disks in the raid 5 and that it is ready, however, the screen then goes blank and I get a blinking cursor and the system seems to hang. There are no activity lights on any of the drives associated with the raid 5, which makes me think that the system is not rebuilding the array at this point.
View 3 Replies
View Related
Apr 7, 2011
I am trying to create a Raid 1 ram disk. Below are the commands I used:
[root@abidbodal dev]# mke2fs -m 0 /dev/ram8
[root@abidbodal dev]# mount /dev/ram8 /mnt/rd8
[root@abidbodal dev]# mke2fs -m 0 /dev/ram9
[code]....
View 3 Replies
View Related
Oct 11, 2010
I'm very new to linux and running debian 4.0. On boot got an error:
I did a ghost image of drive before I do any more damage and when performing the ghost, ghost stated I need to run fsck. I created the image and noticed that a lot of folders were missing (bin, boot and others).
1. How do I run check disk from an boot disk?
2. Is there something else I should consider?
View 1 Replies
View Related
Jun 28, 2010
I have an SiI hardware SATA RAID card, with two 500GB disks in mirrored RAID configuration. When I first plugged them in and set it up, things seemed to work ok, but on boot the raid controller told me that the RAID needed rebuilding, and it would happen automatically after POST. So I didn't worry about it, and the drive mounted fine, and it's been that way for years. I just went in and manually on-line rebuilt the RAID in the controller's BIOS, and now when I boot into Ubuntu, both disks show up in fdisk, but neither show up in /dev/disk/by-uuid. Am I missing something?
View 9 Replies
View Related
Jul 7, 2011
I need to copy data from a single HD, which used to be part of a Linux RAID 1. I've googled around, but can't find any clue how to mount partitions from this single HD.
Background: The HD comes from a linux based NAS box Synology DS207+. The NAS uses ext3 as filesystem. Both NAS disks are fine, but the other NAS hardware is dead and not worth repairing or replacing.
View 1 Replies
View Related
Aug 1, 2010
I had done a new lucid install to a 1 TB RAID 1 array using the alternate CD a few weeks back. I messed up that system trying to some hardware working that lucid doesn't have drivers for yet, so I gave up on it and reinstalled to a single 80 GB disk that I now want to move over to the RAID array.
I moved all of the existing files on the array to a single folder, then copied all of the folders from the 80 GB disk over to the array with permissions and symlinks (minus the contents of /proc and /sys, which I created empty).
These are the commands I used:
Quote:
p -a -d -R -v -t /media/raid_array /b*
cp -a -d -R -v -t /media/raid_array /d*
cp -a -d -R -v -t /media/raid_array /e*
cp -a -d -R -v -t /media/raid_array /h*
[Code]....
I tried to change fstab to use the 689a... for root, but when I try to boot, it's still trying to open /dev/disk/by-uuid/412d...
So then I booted from the single disk again and chrooted into the array, then ran update-initramfs -u. I got 3 "grep: /proc/modules: No such file or directory" errors, and "cat: /proc/cmdline: No such file or directory"- so I created directory /proc/modules, created an empty file /proc/cmdline, and ran the initramfs update again. Then I tried to shut down, which hung (probably because I was doing all of this from a terminal window in Gnome), so I killed the power after a couple of minutes.
It's still trying to use /dev/disk/by-uuid/412d... to boot.
What am I missing? I assume I just have to change the UUID to mount as root, but I don't know how.
View 2 Replies
View Related
Jan 8, 2011
I am looking to build a server with 3 drives in RAID 5. I have been told that GRUB can't boot if /boot is contained on a RAID arrary. Is that correct? I am talking about a fakeraid scenario. Is there anything I need to do to make it work, or do I need a separate /boot partition which isn't on the array?
View 3 Replies
View Related
Jul 6, 2010
So I have a system that is about 6 years old running Redhat 7.2 that is supporting a very old app that cannot be replaced at the moment. The jbod has 7 Raid1 arrays in it, 6 of which are for database storage and another for the OS storage. We've recently run into some bad slowdowns and drive failures causing nearly a week in downtime. Apparently none of the people involved, including the so-called hardware experts could really shed any light on the matter. Out of curiosity I ran iostat one day for a while and saw numbers similar to below:
[Code]...
Some of these kinda weird me out, especially the disk utilization and the corresponding low data transfer. I'm not a disk IO expert so if there are any gurus out there willing to help explain what it is I'm seeing here. As a side note, the system is back up and running it just runs sluggish and neither the database folks nor the hardware guys can make heads or tails of it. Ive sent them the same graphs from iostat but so far no response.
View 1 Replies
View Related
Dec 22, 2010
I installed Debian 5.0.3 (Backport with .34 Kernel), because my server hardware (Dell PowerEdge R210) needs special firmware and drivers.However, the installation went quite smooth.I put the system on a RAID 1 Array with about 500 GB space.s I said the installation went well, however, it doesn't boot! No GRUB, nothing
View 4 Replies
View Related
Mar 24, 2011
If you want, skip straight to the 'QUESTION' at the end of my post & refer to the 'EXPLANATION' later. EXPLANATION: Using Debian 6.01 Squeeze 64-bit. Just put together a brand new 3.3Ghz 6-core AMD. I had a nightmare with my Highpoint 640 raid controller, apparently because Debian Squeeze now handles raid through sysfs rather than /proc/scsi. The solution to this, of course, is to recompile the kernel with the appropriate module for /proc/scsi support. So I thought "screw that" and I've yanked out the raid card & went with Debians software raid. This allowed me to basically complete my mission. The raid is totally up and running, except for one final step... I can't get the raid to automount at boot.
My hardware setup;
- Debian is running totally on a 64Gb SSD. (sda)
- I have 3x 2Tb hard drives used for storage on a raid 1 array (sdc,sdd,sde)
[Code]....
View 2 Replies
View Related
Nov 5, 2010
There seems to be a problem with Raid on Debian. I got a new Fujitsu Primergy TS 100 S1 server, with hardware Raid (and 2 disks) installed everything nicely over the net including GRUB - but when it comes to reboot the system does not boot.
Is there anybody here who knows about the problem?
View 1 Replies
View Related
Dec 1, 2010
I performed an install using the 5.0.6 amd64 netinst cd on a dual opteron server with an Areca ARC-1110 4-port SATA hardware RAID card. I have 2 250GB drives set up as RAID 1. The debian install saw it as only one drive, just as it should. Install went smoothly, but on reboot, the system would not load.
I did some research and tried a couple of things with no luck. Like adding a delay in the grub command. It jus sits at loading system for a while then times out and loads busy box. Just to check things out, I booted into an Ubuntu live-cd and mounted the volume. The file system is there and all of the necessary files. How to use one of these cards successfully?
View 2 Replies
View Related
