Got a little problem after the install of Fedora 12. First there was not problem in opening the raid-device, after i tryed to automount it with crypttab and fstab im not longer able to open it.
Here some outputs code...
I rebooted my server and out of nowhere the RAID5 array won't assemble. I've tried everything I could think of to reassemble the thing. I fear that the array is ruined, but I can't imagine how. Here are various bits of information: The simplest failure (with and without partition numbers, which have not been needed in the past):
Code:
richard@nas:~$ sudo mdadm --assemble --verbose /dev/md0 /dev/sd[bcd]
mdadm: looking for devices for /dev/md0
mdadm: cannot open device /dev/sdb: Device or resource busy
[code]...
I'm having trouble with Ubuntu 10.10 and stable device names. When I installed Ubuntu, the root drive was the only one in the machine; it obviously got /dev/sda.
After the base installation, I installed three additional 2TB drives to make RAID-5 array. Ubuntu renamed the root drive to /dev/sdd. While annoying I lived with it.
After creating a single partition set to "Linux raid autodetect" on each drive, I created the RAID-5 array:
Code:
All was going well until a reboot. When rebooting Ubuntu decided to make the root drive /dev/sda this time and now mdadm --detail /dev/md0 reports:
Code:
How to fix the array and make the device names stable?
I have an Linksys NSLU2 with four usb harddrives attached to it. One is for the os, the other three are setup as a RAID5 array. Yes, I know the raid will be slow, but the server is only for storage and will realistically get accessed once or twice a week at the most. I want the drives to spin down but mdadm is doing something in the background to access them. An lsof on the raid device returns nothing at all. The drive are blinking non-stop and never spin down until I stop the raid. Then they all spin down nicely after the appropriate time.
They are Western Digital My Book Essentials and will spin down by themselves if there is no access. What can I shutdown in mdadm to get it to stop continually accessing the drives? Is it the sync mechanism in the software raid that is doing this? I tried setting the monitor to --scan -1 to get to check the device just once, but to no avail. I even went back and formatted the raid with ext2 thinking maybe the journaling had something to do with it. There are no files on the raid device, it's empty.
I am trying to create a new mdadm RAID 5 device /dev/md0 across three disks where such an array previously existed, but whenever I do it never recovers properly and tells me that I have a faulty spare in my array. More-specific details below. I recently installed Ubuntu Server 10.10 on a new box with the intent of using it as a NAS sorta-thing. I have 3 HDDs (2 TB each) and was hoping to use most of the available disk space as a RAID5 mdadm device (which gives me a bit less than 4TB.)
I configured /dev/md0 during OS installation across three partitions on the three disks - /dev/sda5, /dev/sdb5 and /dev/sdc5, which are all identical sizes. The OS, swap partition etc. are all on /dev/sda. Everything worked fine, and I was able to format the device as ext4 and mount it. Good so far.
Then I thought I should simulate a failure before I started keeping important stuff on the RAID array - no point having RAID 5 if it doesn't provide some redundancy that I actually know how to use, right? So I unplugged one of my drives, booted up, and was able to mount the device in a degraded state; test data I had put on there was still fine. Great. My trouble began when I plugged the third drive back in and re-booted. I re-added the removed drive to /dev/md0 and recovery began; things would look something like this:
Code:
user@guybrush:~$ cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10]
md0 : active raid5 sdc5[3] sdb5[1] sda5[0]
3779096448 blocks level 5, 64k chunk, algorithm 2 [3/2] [UU_]
[Code]...
I am trying to set up a mdadm raid in a new PC that I am building for home theatre. the machine boot just fine from /dev/sdc running ubuntu 9.10 However in gparted /dev/sda and dev/sdb show to be part of /devmapper/sil_ajbicfacbaej Both dev/sda and /dev/sdb were drives that used to be part of a sil hardware raid on a previous machine. I would like to use them as a new mdadm raid on this new machine the old hardware card was really quite slow. the drives are now pluged into the MB and should bw much faster there.
fdisk -l shows this
*********************************************** ~$ sudo fdisk -l
Disk /dev/sda: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders
[code]....
Trying to complete a RAID 1 mirror on a running system and have run into a wall at the last part. I can't add the active physical disk to the mirror. This is on a Centos 5.6 x86_64 system. Anybody know where to go from here? I've tried adding the nodmraid line to the kernel boot line with no luck. Tried removing the logical volumes from LVM, but it won't let me. Not a Linux newbie, but haven't set up a RAID in a long time.
[root@blackbox-0-2-e3-23-72-c5 ~]# mdadm /dev/md1 --add /dev/sda2
mdadm: Cannot open /dev/sda2: Device or resource busy
Here's output from fdisk -l:
[root@blackbox-0-2-e3-23-72-c5 ~]# fdisk -l
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
[code]....
Here's mdadm.conf:
[root@blackbox-0-2-e3-23-72-c5 ~]# cat /etc/mdadm.conf
ARRAY /dev/md0 level=raid1 num-devices=2 UUID=3c6f7354:b9bfc86a:aa9d0dfb:cdd51bd8
ARRAY /dev/md1 level=raid1 num-devices=2 UUID=31ee55ba:be3b3606:974ac87d:627435a9
I have a raid5 on 10 disk, 750gb and it have worked fine with grub for a long time with ubuntu 10.04 lts. A couple of days ago I added a disk to the raid, growd it and then resized it.. BUT, I started the resize-process on a terminal on another computer, and after some time my girlfriend powered down that computer!
So the resize process cancelled in the middle and i couldn't acess any of the HDDs so I rebooted the server.
Now the problem, the system is not booting up, simple black with a blinking line. Used a rescue CD to boot it up, finised the resize-process and the raid seems to be working fine so I tried to boot normal again. Same problem. Rescue cd, updated grub, got several errors: error: unsupported RAID version: 0.91. I have tried to purge grub, grub-pc, grub commmon, removed /boot/grub and installed grub again. Same problem.
I have tried to erased mbr (# dd if=/dev/null of=/dev/sdX bs=446 count=1) on sda (ide disk, system), sdb (sata, new raid disk). Same problem. Removed and reinstalled ubuntu 11.04 and is now getting error: no such device: (hdd id). Again tried to reinstall grub on both sda and sdb, no luck. update-grub is still generating error about raid id 0.91 and is back on a blinking line on normal boot. When you'r resizeing a raid MDADM changed the ID from 0.90 to 0.91 to prevent something that happend happened. But since I have completed the resize-process MDADM have indeed changed the ID back to 0.90 on all disks.
I have also tried to follow a howto on a similar problem with a patch on [URL] But I cant compile, various error about dpkg. So my problem is, I cant get grub to work. It just gives me a blinking line and unsupported RAID version: 0.91.
I installed mdadm fine and all and proceeded to run:mdadm --create --verbose /dev/md0 --level=stripe --raid-devices=2 /dev/sda /dev/sdbWith sda being my primary hard drive, and sdb being the secondary.I get this error message upon running the command"mdadm: chunk size defaults to 64Kmdadm: Cannot open /dev/sda: Device or resource busymdadm: create aborted"I don't know what's wrong!
mdstat says:
"Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] [faulty]
unused devices: <none>"
I have a strange issue with my RAID5 array - it worked fine for a month, a couple days ago it didn't start on boot with mdadm reporting "Input/Output error" - I didn't panic restarted my computer, same error. Then opened a Disk utility and it reported State: Not running, partially assembled - don't know why, I've pressed Stop RAID Array and started it again, voila - it reported State: Running - I've checked components list and there was nothing wrong with it. So I run Check Array utility, waited almost 3 hours to finish it and it worked since than, till today's morning - I've started my computer, and here we go, same error.
See screenshots:
This is an initial state just after computer startup:
This is after I stop and start RAID5:
This is a components list:
I can see nothing wrong there yet not sure why mdadm fails on boot. I do not really like the windows solution I guess, when I check my array again, it will work fine again, but it then can fail in the same way without known reason.
I am planning on setting up a 4x1TB RAID5 with mdadm under Ubuntu 9.10. I tried installing mdadm using "sudo apt-get install mdadm", all worked fine except for the following error: Code: Generating array device nodes... /var/lib/dpkg/info/mdadm.postinst: 170: /dev/MAKEDEV: not found failed. The end result is the /dev/md0 device has not been created, as can be seen here:
Code: windsok@beer:~$ mdadm --detail /dev/md0 mdadm: cannot open /dev/md0: No such file or directory After googling, I found the following bug which describes the issue: [URL] However it was reported way back in April 2009, and it does not look like it will be fixed any time soon, so I was wondering if anyone knows a workaround for this bug, to get me up and running?
I'm writing a monitoring plugin for a home server RAID, mdadm on Ubuntu 10.4. code...
I'm looking for the possible values of "state" but can't seem to find it anywhere, neither man nor the online documentation I have found seem to have a list.
Does anyone know where to find a list of possible states?
I have 4 WD10EARS drives running in a RAID 5 array using MDADM.Yesterday my OS Drive failed. I have replaced this and installed a fresh copy of Ubuntu 11.04 on it.I then installed MDADM, and rebooted the machine, hoping that it would automatically rebuild the array.It hasnt, when i look at the array using Disk Utility, it says that the array is not running. If i try to start the array it says : Error assembling array: mdadm exited with exit code 1: mdadm: failed to RUN_ARRAY /dev/md0: Input/output errormdadm: Notenough devices to start the array.I have tried MDADM --assemble --scan and it gives this output:mdadm: /dev/md0 assembled from 2 drives - not enough to start the array.I know that there are 4 drives present as they are all showing, but it is only using 2 of them.I also ran MDADM -- detail /dev.md0 which gave:
root@warren-P5K-E:~# mdadm --detail /dev/md0
/dev/md0:
Version : 0.90
[code]....
I have done lots of searching and I haven't been able to find anyone else with the same problem. Whenever I create a RAID with 'mdadm', regardless of level (I've done linear, 0, and 5) the command I use is:
Code:
mdadm --create --run --verbose /dev/md0 --raid-devices=11 --spare-devices=1 --chunk=256 --level=5 /dev/sd[abcdefghijkl]1
The RAID is build RAID 5 as it should be. However, when I check /proc/partitions it shows under "md3".
[Code]...
I have a previously defined RAID5 (4 disks). This worked in Ubuntu 8.04.. I recently moved to CentOS5.. and I cannot seen to get the drive back online.cat /proc/mdstat shows, no raid levels (personalities).. and no drives listed.mdadm --detail -scan returns nothing.mdadm --QE returned a UUID string.. and the ARRAY output.I can mdadm --examine all the members of the original array.I am not versed in mdadm enough to really understand what I can run and should not run that would erase the data on the drives. Please assist.. I will try to post exact output of commands.. but the system is kind of unreachable and being rebuilt... i just want to ensure my data on the array is not lost
View 7 Replies View RelatedI'm running a Debian homeserver, with a 3-disk (1GB each) raid 5 array using mdadm (the OS is on a separate disk).Now, smartmontools noticed some bad sectors on one of the disks, and I'm not sure what to do next (except for backup of valuable data).I found some articles on how to fix these sectors, but I'm unaware what the result on the whole array will be.
View 4 Replies View RelatedMy only goal is to have a raid-5 that auto-assembles and auto-mounts. Hardware: 4*2TB sata (raid disks), 1*500GB IDE (OS disk), 1*DVD IDE all plugged direct into the motherboard (nForce 750i SLI).
Starting partitions on the raid disks: gpt ext4 The problem occurs when I restart my comp after building it for the first time. I am able to see it assemble, I am able to partition it, I even mounted it Once.This is the second time I've built it so I have watched everything that happened. I don't know if this has anything to do with my problem, but when I created the raid my drive designations were: sda - 500GB(OS), sd[bcde] - 2TB(raid). When I restarted: sd[abcd] - 2TB(raid), sde - 500GB(OS).
[Code]...
I HAD a fedora 11 server with md RAID 1 across two 1TB SATA drives. The md0 space was set up to be an LVM PV and the single LVM VG was carved up into 5 or 6 LVs. The MB on this system died and I wound up buying a new one.
Now I want to recover the data from the RAID1 setup on the new server. However, when I attach the two 1TB drives to a new fedora 13 setup, mdadm is only able to find one of the two drives. The partition on the second drive shows "busy" during an mdadm -A -s -v to scan for md volumes.
Well, one drive should be enough since this is RAID1, right? Well, when I do a pvscan -v, the other drive shows up as a "NEW" pv not allocated to a VG. In addition, vgscan does print "Invalid metadata header checksum" when it runs but it doesn't point at any particular PV. I'm afraid to go any further with LVM since I can't afford to lose the data on this system. It is backed up offsite, but the restore will take several days and I can't afford to be down that long.
Are there any tools or techniques where I can dig deeper into what each drive, in the RAID1 pair, has right and wrong with it and pick one that I can force into a usable VG so that I can recover the data?
a server that was running a hardware isw raid on the system (root) disk. This was working just fine until I started getting sector errors on one of the disks. So, I shutdown the system and removed the failing drive and installed a new drive (same size). On reboot I went in to the intel raid setup and it did show the new drive and I was able to set it to rebuild the raid. So, continuing the reboot everything came up just fine except the raid 1 on the system disk. I have tried many times to get the system to rebuild the raid using dmraid, but to no avail it would not start a rebuild. In order to get the system back up and make sure that the disk was duplicated I was able to 'dd' the working disk to the new disk that was installed.At present when I look at the system it does not show up with a raid setup on the system disk ( this comprises the entire 1TB disk with w partitions sda1 as / and sda2 as swap).Problem:I have decided to forego the intel raid and just use mdadm. I have a test system setup to duplicate (not the software, but the disk partitions) the server setup.
Code:
[root@kilchis etc]# fdisk -l
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
I have a 7-drive RAID array on my computer. Recently, my SATA PCI card died, and after going through multiple cards to find another one that worked with linux, I now can't assemble the array. The drives are no longer in the order they were in previously, and mdadm can't seem to reassemble the array. It says there are 2 drives and one spare, even though there were 7 drives and no spares. I know for a fact that none of the drives are corrupted, because one of the non-working RAID cards was still able to mount the array for a short period, but would loose the drives during resyncing (I later found out that the chipset on the card was had extremely limited linux support). I have tried running "mdadm --assemble --scan" and after the drive is partially assembled, I add the other drives with "mdadm --add /dev/md0 /dev/sdc1". These both return errors and will not complete on the new raid card.
Code:
aaron-desktop:~ aaron$ sudo mdadm --assemble /dev/md0
mdadm: /dev/md0 assembled from 2 drives and 1 spare - not enough to start the array.
[code]....
Recently, one the SMART utility said that one of the drives had failed and another drive was about to fail. I downed the box and hooked them up to my windows machine to run sea tools on them (They are all seagate drives). Sea Tools said that the drives were fine, while ubuntu said they were failing/dead. Yesterday I decided to try to fix one of the drives in the raid. I turned the server off, took the failed drive out, and restarted. Of course the raid didn't work because only 2 of the 3 drives were there, however it had been working w/ only 2 of the 3 drives for a couple months now (I'm a lazy college student). I turned it back off and back on with the drive there just to see if I could get the raid up again, but I havn't been able to get it to go. So far I've tried:
Code:
mdadm --assemble /dev/md0 /dev/sd[b,c,d]
mdadm: no recogniseable superblock on /dev/sdb
mdadm: /dev/sdb has no superblock - assembly aborted
[code]....
I'm looking for a way to trick the raid into working with just 2 drives until I can warranty the seagate and buy an external 1.5 TB drive to use as another backup. how to remove the bad drive from the array and replace it with a fresh drive, without data loss.
I just had a whole 2TB Software RAID 5 blow up on me. I rebooted my server, which i hardly ever do and low and behold i loose one of my raid 5 sets. It seems like two of the disks are not showing up properly.. What i mean by that is the OS picks up the disks, but it doesnt see the partitions.
I ran smartct -l on all the drives in question and they're all in good working order.
Is there some sort of repair tool i can use to scan the busted drives (since they're available) to fix any possible errors that might be present.
Here is what the "good" drive looks like when i use sfdisk:
Quote:
sudo sfdisk -l /dev/sda
Disk /dev/sda: 121601 cylinders, 255 heads, 63 sectors/track
Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0
Device Boot Start End #cyls #blocks Id System
/dev/sda1 0+ 121600 121601- 976760001 83 Linux
/dev/sda2 0 - 0 0 0 Empty
[Code]....
I have a fileserver which is running Ubuntu Server 6.10. I had a RAID5 array consisting of the following disks:
Code:
/dev/sda1
/dev/sdb1
/dev/sdd1
/dev/md0 -
the raid drive for the above three disks. The sda1 disk has failed and the array is running on 2 of 3 disks
/dev/sdc (OS disk)
/dev/sde (new 2tb disk - unused)
/dev/sdf (new 2tb disk - unused)
My plan was to rebuild the array using the two new disks as RAID1. Would the best way to do this be to create a new RAID1 disk on /dev/md1 then copy all data over from /dev/md0? Also - this may sound stupid but since all 3 drives in md0 are identical i'm not sure physically which disk is bad. I tried disconnecting each disk one-by-one then rebooting but the system doesn't appear to want to boot without the bad drive connected. I've already failed the disk in the array with mdadm but i'm unsure of how to remove it properly.
Can I use UUIDs to setup a raid with mdadm?
View 3 Replies View RelatedMy home-backup server, with 8*2TB disks won't boot anymore. Two disks failed at the same time and i rebuilt the raid 6 array without any problem, but now i can't boot the os. I'm using ubuntu server, 10.10. I've made screens of the displays to don't copy everything here. The problem at the boot:
And the Grub config: It's not a production server, but i would like to have it online. I've tried for the lasts 2 days (just a couple hours a day) but without success. I was suggested to do "mount -o remount,rw /" and than edit /etc/fstab, but it get the file don't exist error.
I am trying to create a Raid 1 ram disk. Below are the commands I used:
[root@abidbodal dev]# mke2fs -m 0 /dev/ram8
[root@abidbodal dev]# mount /dev/ram8 /mnt/rd8
[root@abidbodal dev]# mke2fs -m 0 /dev/ram9
[code]....
I have been having some odd issues over the last day or so while trying to get a raid 5 array running in software under Kubuntu. I installed 3 1TB drives and started up, my sd* order got all messed up( sda was now sdc and so on). This wasn't entirely unexpected, so I fixed up fstab and booted again. I found all three of the drives I installed, set them to raid auto-detect and used mdadm to create /dev/md0. I then created mdadm.conf by piping the output of mdadm --detail --scan --verbose into /etc/mdadm.conf.At this point, everything was still going swimmingly. I copied over a few hundred GB of data from another failing drive and everything seemed ok. I went to reboot once the copy was done and everything just went weird. All of the sd* drives went back to the original. Of course, this meant that the mdadm.conf was wrong. I tried to just change the device list, but that didn't work. I then deleted mdadm.conf and rebooted. The drive list stayed in the original order this time, so I just tried manually starting the array.
By erasing the partition table of the 3rd drive, I've been able to get it to the status of spare, but it says it is busy when I try to add it to the array. A grep through dmesg makes me think that md has a lock on it. I'm not sure where to go with it now. If anyone has any pointers, I would like to hear them.
Device List(original):
/dev/sda => boot drive, /home /
/dev/sdb => 1.5TB media storage, failing
[code]...
mdadm --create /dev/md1 --level=1 --raid-disks=2 missing /dev/sdb1and I getmd1: raid array is not clean -- starting background reconstructionWhy is it not clean?Should I be worried?The HD is not new it has been used in before in a raid array but has beenrepartitionated.
View 2 Replies View RelatedI have 4 WD10EARS drives running in a RAID 5 array using MDADM.Yesterday my OS Drive failed. I have replaced this and installed a fresh copy of Ubuntu 11.04 on it. then installed MDADM, and rebooted the machine, hoping that it would automatically rebuild the array.It hasnt, when i look at the array using Disk Utility, it says that the array is not running. If i try to start the array it says :Error assembling array: mdadm exited with exit code 1: mdadm: failed to RUN_ARRAY /dev/md0: Input/output error
mdadm: Not enough devices to start the array.I have tried MDADM --assemble --scan and it gives this output:mdadm: /dev/md0 assembled from 2 drives - not enough to start the array.I know that there are 4 drives present as they are all showing, but it is only using 2 of them.I also ran MDADM -- detail /dev.md0 which gave:
root@warren-P5K-E:~# mdadm --detail /dev/md0
/dev/md0:
Version : 0.90
[code]...
When we assemble a raid array, from where does it load configuration information for that array? I thought it refers to /etc/mdadm.conf file, but in my system, mdadm.conf file doesn't even contain all information. Still it is able to successfully assemble previously created device.
# cat /etc/mdadm.conf
DEVICE /dev/sd[bcdjkl]1
DEVICE /dev/loop[012345]
[code]...
