Ubuntu Servers :: VPN Setup Peer Negotiation Failed

May 23, 2011

I've followed [URL] to set up vpns with some external networks. So far it worked like a charm on two of them. But when trying to connect to the third one I instantly get bumped off.

When running
Code:
pon dymka debug dump logfd 2 nodetach

I get this as part of my output
Code:
CHAP authentication succeeded
sent [CCP ConfReq id=0x1 <mppe +H -M +S -L -D -C>]
rcvd [IPCP ConfReq id=0x26 <addr 192.168.0.2> <compress VJ 0f 00>]
sent [IPCP TermAck id=0x26]
rcvd [CCP ConfReq id=0x3e <mppe -H -M +S -L -D -C>]
Refusing MPPE stateful mode offered by peer
MPPE required but peer negotiation failed
sent [LCP TermReq id=0x2 "MPPE required but peer negotiation failed"]
sent [CCP ConfRej id=0x3e <mppe -H -M +S -L -D -C>]
rcvd [CCP ConfNak id=0x1 <mppe -H -M +S -L -D -C>]
Discarded non-LCP packet when LCP not open
rcvd [LCP TermAck id=0x66]
Connection terminated.
Waiting for 1 child processes...
script pptp xxx.xxx.xxx.xxx--nolaunchpppd, pid 8920
Script pptp xxx.xxx.xxx.xxx --nolaunchpppd finished (pid 8920), status = 0x0

I've looked all over the internet but sollutions like adding mmpe-stateful to options.pptp doesn't work. Is this a problem with the client or with the server? Because the server is configured just like the other two and they work as intended. Seemed to be a problem on the firewall.

View 3 Replies


ADVERTISEMENT

Ubuntu Servers :: SSH Error: Read From Socket Failed: Connection Reset By Peer?

Dec 8, 2010

figure out this error?

Code:
kradalby@hpcompaq6530b-laptop ~/.ssh $ ssh -vvv -p 110 kradalby@dfekt.no
OpenSSH_5.5p1 Debian-5+b1, OpenSSL 0.9.8o 01 Jun 2010

[code]....

View 3 Replies View Related

Networking :: TLS Error: TLS Key Negotiation Failed To Occur Within 60 Seconds

Jan 24, 2011

i set up openvpn on server and configure it then create license file for client and done the rest but when the client want to connect i got the following error :

TLS Error: TLS key negotiation failed to occur within 60 seconds

and now the strange part is if i connect my pptpd connection ( which runs on another server ) and then connect openvpn again i connect instantly without any problem or error in my country im sure there is heavy firewall on all outgoing traffic but currently i do not understand what can cause this problem
i ran tcpcump and seems server receive packets and send it back to client ( though im not sure if client can get the response ) this is my server.conf

Code:

local myserver ip #Replace with your server IP address
port 443 #Replace with the desired port
proto udp #Choose between tcp and udp (remove instructions in bold)

[code]...

View 2 Replies View Related

Ubuntu :: Error While Getting Peer-to-peer Dbus Connection: The Name :1.219 Was Not Provided By Any .service Files

May 26, 2010

When I plug in my iPhone to my 10.04 machine, it's recognized. I can always drag music from the iPhone to the Music collection in Rhythmbox, but 9 times out of 10 dragging the other ways gives me this error:

"Error while getting peer-to-peer dbus connection: The name :1.219 was not provided by any .service files"

View 2 Replies View Related

Ubuntu :: Setting Up Samba On A Peer-to-Peer Network With Windows XP

May 30, 2010

I am using Ubuntu 10.4 LTS and Samba3.4.7.I have read a lot of posts and different web pages on setting up Samba on a Peer-to-Peer network with Windows XP but just cant make it work. I can see the Guest account in XP My Network Places but cant access the folder when I click on it.Network not accessible or you dont have permission. I can PING both ways ok. I have Firestarter turned OFF and I dont have any third party firewall on XP.

This is my samba config file:

[global]
netbios name = dolphin
server string = Ubuntu
workgroup = WATERLILLY - same as XP

[code]....

View 3 Replies View Related

Fedora :: Installing Frostwire Or Other Peer To Peer Programs?

Jul 11, 2010

Where do I get Frostwire to install? None of the repos I have have it.

What are other popular peer to peer programs?

View 14 Replies View Related

Ubuntu Networking :: Peer To Peer Filesharing Between PC's

Mar 2, 2010

I know I'm missing something absolutely basic here but when I search the forums for filesharing I only seem to get info referring to Windows filesharing/SAMBA etc.

We have 3 Ubuntu machines at home and a printer on a Windows machine. How can we best fileshare:

1) between Ubuntu machines
2) reliably between Ubuntu and the Windows machine

Printing across the network is ok except for the Karmic NBR machines but that's another thread.

View 9 Replies View Related

Server :: Amanda - Selfcheck Request Failed: Recv Error: Connection Reset By Peer

Feb 22, 2011

when i ran amcheck DailySet1 as backup user and got these messages:

[Code]....

View 3 Replies View Related

Ubuntu Networking :: Ssh "Connection Reset By Peer" - Write Failed: Broken Pipe

Feb 9, 2010

which cropped up today after no changes to the system: I can successfully ssh into my ubuntu 64-bit 9.10 machine (via OS X with iTerm), but after about 30 seconds, the connection drops with the message "Connection reset by peer Connection to xx.xx.xx.xx closed".

If I then try to immediately ssh back in I get: "Write failed: Broken pipe". If I try to immediately ping the machine instead, I cannot ping it until the ~10th try. Eventually I can log back in again, only to be kicked off after between 5 and 60 seconds. I called the network people and their are no known issue right now with networking. The networking on the ubuntu machine is otherwise fine, it seems. In the /var/log/auth.log file, it simple says:

Quote:
Feb 9 14:19:20 harriet sshd[4134]: Accepted password for xxx from xx.xx.xx.xx port 55105 ssh2
Feb 9 14:19:20 harriet sshd[4134]: pam_unix(sshd:session): session opened for user xxx by (uid=0)
Feb 9 14:19:28 harriet sshd[4046]: pam_unix(sshd:session): session closed for user xxx

The solution I come across to a similar problem is to add a "ClientAwakeInterval" number to sshdconfig, but this (as expected) doesn't fix my problem.

View 1 Replies View Related

Fedora Networking :: Turning Off Auto Negotiation?

Aug 24, 2010

Im trying to maximize my network connectivity. To do this I have begun using the program ethtool. The first thing I did was run

Code:
#ethtool eth0
which informed me Im running 10BaseT mode. So i though, ok, that has to do with the autoneg right?
so I ran:
Code:
# ethtool -s eth0 speed 1000 duplex full autoneg off

[Code]...

LOLz, I got it now, This computer has 2 nics installed! Thats why the link stat was "Link detected: no"
I moded my code to pertain to eth1, the connected port. Eh, anyhow, Im still not sold on this problem being solved, the connection eth1 seems to work fine at 100BaseT/Full but I loose connectivity when trying to use 1000BaseT/Full despite the nic showing it as a supported mode.

View 4 Replies View Related

General :: Testing Negotiation Between Server And Client?

Apr 11, 2010

How do i test negotiation between server and client for various protocols like:

ppp
pppoe
pptp
L2tp
dhcp

View 5 Replies View Related

Ubuntu Servers :: Setup New Remote Office - Setup Domain Trust Between Two Sites?

Mar 14, 2010

I ended up setting up a basic linux file server as a pdc for that office. Our main office is a windows 2000 ads domain. The two offices are connected with a vpn. I only have two users at the new location so I simply have the linux and samba usernames/passwords setup manually. I would like to know if it is possible to setup a domain trust between the two sites so I don't have to create a username/password in the remote site for every user at the main office to access. I did some searching but came up empty.

View 5 Replies View Related

Ubuntu Networking :: Failed To Setup Net Connection In 9.10?

Jun 18, 2010

I recently setup ubuntu 9.10 in my desktop..I don't know whether the connection is dialup or not. I used the connection with cable connection. I have got the following information from my ISP:

User name: n372_asad_go@brisksys.net
service name: brisknb
password: 16251521

View 1 Replies View Related

Ubuntu :: Apache2 SSL Setup - Secure Connection Failed

Mar 23, 2010

I followed the tutorial found here [URL] but when I try to access [URL] I get the following:
Code:
Secure Connection Failed
An error occurred during a connection to www.mydomain.com.
SSL received a record that exceeded the maximum permissible length.
(Error code: ssl_error_rx_record_too_long)
Not sure what I might have done wrong... I have retraced all of my steps and I don't believe I missed anything.

View 2 Replies View Related

Software :: Using Zapping TV Viewer - Setup Failed

May 28, 2010

I installed Zapper TV viewer in ubuntu 9.10.But after installation. When I opened the Zapper TV viewer application two error messages were shown. They are:

1.Cannot restore previous mode:
/usr/bin/zapping setup_fb failed.
DNA is not possible on screen 0.

2.Cannot start capturing:/build/buildd/zapping-0.10~cvs6/src/tveng25.c:queue_xbuffer:2067:ioctl VIDIOC_QBUF failed: 22, invalid argument.

View 1 Replies View Related

Ubuntu Networking :: Samba Setup Error - Failed To Add Entry For User

Jun 20, 2010

I am trying to set up my Ubuntu 10.04 netbook to see my WinXP desktop's files and vice a versa. I followed the steps in this tutorial thread: HOWTO: Setup Samba peer-to-peer with Windows. I got as far as "Time to add yourself as an samba user." at this point I keep getting the following error:

Code:
sudo smbpasswd -L -a WinXP_User_Name
New SMB password:
Retype new SMB password:
Failed to add entry for user WinXP_User_Name.
My WinXP machine has no password.

My conf file is here:
[global]
; General server settings
; netbios name = WinXP_Computer_Name
server string =
; workgroup = WinXP_WorkStation_Name
announce version = 5.0
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE SO_RCVBUF=8192 SO_SNDBUF=8192
passdb backend = tdbsam
security = user .....

View 9 Replies View Related

OpenSUSE Hardware :: 11.3 Hplip Printer Queue Setup Failed?

Jul 31, 2010

I just installed opensuse 11.3 and was configuring the printer (via http) as usually using the HP Device Manager. But this time I got these error message:Printer queue setup failed. Please restart CUPS and try again

These lines were generated in the error-log of cups:
E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Bad driver information file "/usr/share/cups/drv/sample.drv"!
E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Skipping "/usr/share/ppd": loop detected!

[code]....

View 9 Replies View Related

Ubuntu Networking :: GPRS - LCP Terminated By Peer

Nov 20, 2010

I am trying to get pppd/chat working with an internal Wavecom modem, but PPP terminates with message "LCP terminated by peer". But, same pppd/chat configuration is working on my own Linux OS with Huawei 3G modem. I tried several options to get it working, but no luck. The problem is happening during the PPP negotiation with the Modem:

rcvd [LCP TermReq id=0x2]
LCP terminated by peer

But this only mean that there was a failure during PPP setup between Linux and the Modem. I tested the modem with manual AT commands via minicom to further investigate to problem, but could not even activate the PDP context:

Modem is registered and attached to Vodacom's network:

at+cops=?
+COPS: (2,"VodaCom-SA","VODA","65501"),(3,"MTN-SA","MTN","65510"),(3,"","","65502"),(3,"Cell C","C)
at+cops?
+COPS: 0,2,65501

[code]....

View 1 Replies View Related

Ubuntu :: Pipe Error 3 - Connection Reset By Peer

Jul 6, 2010

My system just crashed.
kduffy101@kduffy101-desktop:~$ firefox
WARNING: pipe error (3): Connection reset by peer: file ./src/chrome/common/ipc_channel_posix.cc, line 404
Segmentation fault
kduffy101@kduffy101-desktop:~$.

View 4 Replies View Related

Ubuntu Networking :: Rdesktop Connection Reset By Peer

Jul 15, 2010

I've happily been using rdesktop to access my MS Vista desktop from Ubuntu (Hardy) for a few months until a couple of days ago when it stopped working. Now if I try connecting I get the following:

[Code]....

I don't believe anything's changed on the client (Ubuntu) side. The Vista box is occasionally connected to a corporate intranet via VPN and it was after such a session that rdesktop stopped working, so perhaps a Windows group policy was modified during the session. I've checked the basics - can ping 10.1.1.2 from Ubuntu, can access port 3389. Have deleted ~/.rdesktop and ~/.tsclient.

Digging around the Vista client I noticed in Control Panel > System Properties > Remote that in the Remote Desktop sub-panel the Allow connections only from computers running Remote Desktop with Network Level Authentication setting is enabled and that the other two are greyed out. Now, I don't know whether this setting has been changed but I suspect that it might be the problem.

Unfortunately, I don't know enough about Windows to know how or even whether I can change this setting to Allow connections from computers running any version of Remote Desktop (less secure) I've poked around the group policy editor (gpedit.msc) but no joy.

View 9 Replies View Related

Ubuntu :: Peer Block Type Program For System?

Aug 12, 2010

Is there a program like peer block for ubuntu? It is an ip filter program. Here is the website to help answer questions on what type of program it is. http://www.peerblock.com/

View 6 Replies View Related

Ubuntu :: Error: Cannot Load AWT Toolkit: Gnu.java.awt.peer.gtk.GtkToolkit

Jan 29, 2010

I want to view the files for RepRap, but do not know which java files to install. Here is the error readout from running the reprap shell script.

Code:
keeper@keeper-netbook:~/Desktop/reprap-mendel-20100105$ ./reprap
Exception in thread "Main" java.awt.AWTError: Cannot load AWT toolkit: gnu.java.awt.peer.gtk.GtkToolkit
at java.awt.Toolkit.getDefaultToolkit(libgcj.so.81)
at java.awt.EventQueue.invokeLater(libgcj.so.81)
at javax.swing.SwingUtilities.invokeLater(libgcj.so.81)

[Code]...

View 2 Replies View Related

Ubuntu :: Possible To Import The Block Lists From Peer Guardian Into Transmission?

Oct 1, 2010

Is it possible to import the block lists from say , Peer Guardian, into Transmission?

I'm not au fait with what Transmission can do, maybe it has a block list capability anyway.

View 5 Replies View Related

Fedora Networking :: 3G USB Modem - LCP Terminated By Peer

Sep 7, 2009

I recently upgraded to Fedora 11, and am having an issue with the USB modem (Novatel USB720) disconnecting almost immediately after it is connected. Sometimes it disconnects 30 seconds after it is connected, sometimes 2-3 minutes. And other times it stays connected for hours without a problem. I know the card is good as it works using Verizon Connection Manager software under Windows and never had this problem.

And, I am able to get to the Internet while it is connected, so it is passing traffic OK. I'm using the NetworkManager to connect the "Auto Mobile Broadband" connection. I've seen other posts on this very same issue, and I verified that pppd is called using the "lcp-echo-failure 0" and "lcp-echo-interval 0" options. But it seems that when it does disconnect, in /var/log/messages it says "LCP terminated by peer".

Below is an example of /var/log/messages where we can connect, then it immediately disconnects.
Sep 7 09:55:08 c3po NetworkManager: <info> Activation (ttyUSB0) starting connection 'Auto Mobile Broadband (CDMA) connection'
Sep 7 09:55:08 c3po NetworkManager: <info> (ttyUSB0): device state change: 3 -> 4 (reason 0)
Sep 7 09:55:08 c3po NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled...
Sep 7 09:55:08 c3po NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started...
Sep 7 09:55:08 c3po NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete.
Sep 7 09:55:09 c3po NetworkManager: <info> (ttyUSB0): powering up.....

View 5 Replies View Related

OpenSUSE Network :: KDE Hangs When Peer On Nfs Is Offline?

May 27, 2011

I have a couple of nfs shares which I configured through the yast NFS client module. It entered these in my fstab file to start on bootup. A sample entry is:

10.2.1.30:/home/opt/Cindy/homenfsdefaults 0 0

As long as the foreign computer is online all is well. If the foreign computer is taken off line, soon after KDE applications such as Dolphin and the panel freeze, even if I am not using the shares. When the foreign computer comes online again, everything unfreezes on my computer and works fine. Likewise, if the other computer is not online when I boot, there is a long delay while the system waits for the share to come up. Is there something in my configuration that I can change to stop either or both of these problems? I am running 11.4 x86_64 on a wired network with static ip addresses.

View 9 Replies View Related

Fedora :: YUM Freezes With Error - Peer Certificate Invalid

Sep 17, 2010

My organization just moved to using a zscaler proxy system. Basically, I have to use a .pac file in Firefox to get onto the proxy, which directs me to a series of two Flash pages, one to input my username, one for the password. After reading through the .pac file, I was able to get some command-line things to work by specifying the proxy given at the end. However, this server uses an SSL certificate that is not emitted by an authority, but rather directly by our organization. In Firefox, I had to import this certificate to enable https:// browsing.

Is there any way to "import" this certificate so that yum can use it? Because yum freezes with the error:
Code:
Could not get metalink [URL] error was
14: Peer cert cannot be verified or peer cert invalid

View 6 Replies View Related

OpenSUSE Network :: TLS : Hostname Does Not Match CN In Peer Certificate

Feb 16, 2011

I'm trying to use LDAP with TLS but allways got Connect error. The message error is TLS : hostname does not match CN in peer certificate So I've tried to generate new certificate with my hostname for CN but my LDAP still don't want to work with TLS.

I use opensus 11.3. I used YAST2 for crating my CA and certificates.

View 9 Replies View Related

Ubuntu :: Xinit: Connection Reset By Peer (errno 104): Unable To Connect To X Server

Oct 2, 2010

when i run "sudo startx" i get the message:

"(= Log file: "/var/log/Xorg.0.log", Time: Sat Oct 2 15:33:49 2010
(= Using config file: "/etc/X11/xorg.conf"
(II) Module "ddc" already built-in

[code]....

Fatal server error:

no screens found

waiting for X server to begin accepting connections giving up.

xinit: Connection reset by peer (errno 104): unable to connect to X server
xinit: No such process (errno 3): Server error."

My version of ubuntu is 8.04 and the video card is 82G33/G31 Express Integrated Graphics Controller.

View 9 Replies View Related

OpenSUSE Network :: Vpnc Killed Due To Dead-peer Detection / Fix It?

Sep 7, 2011

But I don't think my peer is dead.

View 1 Replies View Related

Ubuntu Servers :: Setup More Than 2 Sub Domains On 9.10?

Jan 29, 2010

I've built a web hosting server with ubuntu 9.10 desktop edition at home and it's up and running.how to get and set subdomains. What I mean is that I have a purchased domain [URL] and I want to add as many sub domains as I want such as [URL] so on. And more importantly every single subdomain must belong to each account.

sub domain      account name
-------------------------------------------
sub1.example.com   john
sub2.example.com   steave
sub3.example.com   myname

In this case, there are three accounts for ubuntu and each account has a permission to the corresponding sub domain only. p.s My DNS is managed by my domain company and it provides a web page where I can forward(not sure, but there are fields that I can type my sub domains) subdomains and my external IP addresss up to 20(just in case this info matters).

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved