Ubuntu Security :: WNA 1100 Netgear Wireless Adapter Monitor And Injection Mode?

Mar 2, 2011

I want to do some pen-testing using aircrack-ng on my local network and currently the only wireless adapter I have is the WNA 1100 netgear adapter. I am using the ath9k_htc driver.

View 7 Replies


ADVERTISEMENT

Ubuntu Networking :: Netgear WNA 1100 USB WiFi Adapter Not Working

Jul 9, 2010

Okay I've got a Netgear N-150 WNA 1100 USB WiFi adapter, it doesn't work in Ubuntu it's not supported. There should be a way to make it work with ndiswrapper. I tried and failed before and due to other non related circumstances I had to reinstall Ubuntu. What are the steps to install ndiswrapper and it's dependency's on a fresh Ubuntu installation that cannot connect to the internet.

View 9 Replies View Related

General :: Broadcom BCM4328 Wireless Adapter Not Supporting Monitor Mode Using WL And B44?

Feb 8, 2009

A friend of mine has a Dell XPS1530 lappy that has a broadcom bcm4328 wireless adapter. I tried installing kismet on it so I can scan for wireless network in range. I configured it with the source driver as bcm43xx in kismet.conf and complained that the driver didn't support monitor mode. It uses the proprietary 'wl' kernel module to operate but kismet can't use the 'wl' module and it says the same error. I tried unloding the wl and b44 modules and loding the b43 driver but then the adapter stoped working. I searched on the net a bit and found out that kisment doesn't work with the prorpietary drivers for that card.

View 14 Replies View Related

Networking :: NetGear - WN111 V2 Usb Wireless Adapter ?

May 16, 2010

I'm running Slakware 13 (kernel 2.6.29.6) on a inspiron 1525. I use ndiswarper to use the BCM4312 wireless device without any problem but the fact that the driver does not support the Monitor mode. I therefore bought a NetGear WN111 v2 usb stick but I can't get the linux driver.

Even ndiswarper does not work but it's may be because I don't have the right .sys .ins files. (just to try)

So, I wonder if someone has already successfully manged this device working on Slackware 13?

Actually, I don't know if we can make lets say wlan0 and wlan1 working at the same time. I've try many drivers mentioned on Ubuntu forums but none of theme work with me.

Many people talk about wpa_supplicant but I don't know if I really need it to make my wn111v2 working. And what is a firmware?

View 2 Replies View Related

Ubuntu Networking :: Can't Get Wg111t Netgear Wireless Adapter To Work

Mar 5, 2010

i can't get my wg111t netgear wireless adapter to work. I followed the help thing by installing ndisgtk, which installed successfully. I was able to load up the file on the cd that also the help page said. The problem is that the computer won't load up the adapter as it would load up my cd's and flash drive. Here's how i installed ndisgtk. I installed the files ndiswrapper_common, ndiswrapper_1.9, and then the ndisgtk_0.8.5.All of these were for i386.

View 1 Replies View Related

Ubuntu Networking :: Netgear Wireless N PCI Adapter WN311B-100NAS

Mar 24, 2010

I just bought a Netgear N PCI wireless network card and was hoping Ubuntu 9.10 would recognize it. I installed the card and was using XP on the machine (Dell Dimension 2400) and decided to install 9.10 on this computer instead (XP = slow!). I'm not sure how to get Ubuntu to recognize it. I was hoping this would be a 'plug and play' install

View 4 Replies View Related

Hardware :: Netgear WG511v2 Wireless Adapter - Almost Working

Dec 17, 2008

Running HH on a little Toshiba Satellite something-or-other laptop (I want to say A25, but who knows), Verizon FIOS router (wired and wireless).

NetGear WG511v2 adapter is so close to working...

Didn't seem to want to work with ndisgtk, so I ran ndiswrapper from terminal, using driver folder I copied from my Win2K partition.

(Had to do a cp WG511v2.sys WG511v2XP.sys, as the .inf file referred to the latter, but such did not exist; cp seemed to do the trick.) And now, survey says:

Code:

Code:

Code:

In "Network Settings", the card detects a few wireless networks (including my own in-home router). Status LED flashes constantly (which I interpret to be hunting), and every several seconds, it goes solid while activity LED flashes a few times (which I interpret to be finding a network, attempting communication), then activity LED ceases to flash and status LED goes back to flashing (which I interpret to be failing and going around again). Using DHCP, just like the other computers that connect without incident.

I have entered my WEP every way I can think of. The dialog lets me choose WEP ASCII or WEP hexadecimal; I have entered the key in all caps and in lowercase, as ASCII and as hex, have entered 0's and O's where applicable. No combination seems to allow it to actually communicate with my router beyond getting rejected. My other laptop and PC (and this laptop, when running Win2K) all connect just fine; none of them use WPA-type passphrases, so I assume that's unnecessary from Ubuntu. Roaming mode gives the same results as described above.

View 5 Replies View Related

General :: Install The Netgear Wireless Adapter Driver?

Dec 23, 2009

time Windows user here; limited line command experience from early computer learning; Just wiped my drive and installed Ubuntu. How do I install a driver for the netgear wireless adapter - it was already installed in the machine. I've downloaded the driver believed to work. What next? Also, any instruction on educating myself on Linux/Ubuntu basics?

View 14 Replies View Related

Fedora :: Unable To Configure Netgear WG111v3 Wireless Adapter In KDE?

Dec 31, 2010

I recently installed Fedora 14 and am unable to configure my Netgear WG111v3 wireless adapter in KDE However XFCE and Gnome work fine. Has anybody had this problem?

View 1 Replies View Related

Fedora Networking :: Netgear WG111v2 Wireless Adapter Won't Stay Online

Jan 28, 2010

I just installed Fedora 12 on my HP a430n PC.I used to run Fedora 10, then moved to Linux Mint 7, then to Ubuntu 9.10 and now I am back to Fedora because I want to become more adept with manual package installation and adding repos.When I ran Fedora 12 immediately after then install, before running yum update PackageKit or the software update, it would use my wireless adapter (Netgear WG111v2) and connect to and stay connected to a network just fine. No hiccups.After running the updates and restarting the computer, the wlan won't stay connected for longer than 20 seconds, which is frustrating when trying to install mp3 codecs.

This seems to be a bug in the latest driver update for the WG111v2, but I might be wrong. Anyone have a fix or a way to revert back to the initial driver (I don't know what the original wireless driver was called).

View 1 Replies View Related

General :: Internet Connection - Netgear WPN111 Wireless Adapter Work With 10.10?

Dec 28, 2010

Will the Netgear WPN111 wireless adapter work with Ubuntu 10.10? If so what action is required to get connected with it running Ubuntu 10.10. The adapter works with Windows XP.

View 2 Replies View Related

Ubuntu Networking :: Xubuntu 10.04 IBM Thinkpad 390X Netgear WG511 PCMIA Wireless Adapter?

Jan 21, 2011

Edit: after upgrading everything using a usb to ethernet port converter ndiswrapper is working perfectly

I do not have internet access on a laptop I am trying to upgrade. It has no ethernet port. I may resort to buying a USB to ethernet adapter but I spent more than I would like to have already. I have tried every command in the HOWTO for wireless difficulties and posted the output.

[Code]...

View 4 Replies View Related

OpenSUSE Install :: WPN111 Wireless Adapter And NETGEAR - Make The Module Load Automatically On Boot ?

Feb 14, 2011

Above adapter can be installed on v10.2 and 11.3 using ndiswrapper:-

1. Copy the 3 driver files from Windows:- like netwpn111.inf, WPN111.sys & ar5523.bin.
(Be carfeul about the exact names, because they have changed over time).

2. sudo ndiswrapper -i netwpn111.inf

3. sudo ndiswrapper -m

4. sudo modprobe ndiswrapper (the adapter should light up at this point and networks will be detected shortly after - see network manager). (Be careful of paths here - e.g. I had to use /sbin/modprobe - so 'whereis' may be necessary to find these commands).

2nd When I reboot, I need to run the modprobe command again. How do I make the module load automatically on boot? Also (and this is minor), can I bypass the KWallet, keyring thing? it seems silly to enter a password for the keyring and then click another password dialog, when I can just as easily enter the password for the network itself.

View 1 Replies View Related

Ubuntu Networking :: Can't Get Wireless (atheros) Into Monitor Mode

Mar 22, 2010

I can't get my wireless into monitor mode. I;m running ubuntu 9.1 karmic It connects fine to wireless networks. But when i do: sudo iwconfig wlan0 mode monitor. I get: Error for wireless request "Set Mode" (8B06) :SET failed on device wlan0 ; Device or resource busy. I can only see wlan0 (wmaster0, eth0), not ath0 or wifi0 mentioned elsewhere, in wireshark. I only see my own ip and packets coming to and from that. my system tells me i have an atheros ar9285 chipset in place.

View 2 Replies View Related

Security :: Protect Server From Url Injection?

May 20, 2010

I am facing problem on my Linux server, those runing php sites, most of the time hacker upload file in my website and take the control, and hack the sites, shoot the thousands of mail etc

View 7 Replies View Related

Ubuntu Security :: Block PHP Injection Attacks With Fail2ban

Apr 12, 2010

I'm trying to implement this method to block php injection attack using fail2ban: here it is, however I'm not sure it applies to Ubuntu. You see, there's this filter that must be added to the fail2ban jail file:

HTML Code:
[php-url-fopen]
enabled = true
port = http,https
filter = php-url-fopen

[Code]....

View 7 Replies View Related

Debian Hardware :: Netgear USB Adapter Can't Connect

May 2, 2014

WG111v2 USB that works just fine on my Ubuntu 12.04 Dell can't connect on my Debian Gigabyte. It finds the network name just fine, remembers its password, and tries to connect 3 times before giving up. This tower is 4 days old, as is the OS.

View 1 Replies View Related

Ubuntu Networking :: Wireless Card Wont Stay On Monitor Mode!?

Dec 9, 2010

Running Ubuntu 10.10 on Hp Mini 1030nr My wireless card is a Broadcom BCM4312. I have the b43 driver installed. When I disable networking I can change to monitor mode but then it changes back to manage mode when I enable networking again. I tried using airmonNG but it;s not working.

View 1 Replies View Related

Ubuntu Networking :: Netgear Adapter - Slow & Disconnects - After 5 Minutes

Nov 30, 2010

Just installed yesterday - and I love it so far except my wireless turns on for about 5 minutes, then disconnects.

In order to get internet back I have to either restart or uncheck "Enable Networking" and then recheck it.

I will try to provide as much information, but like I said I am new to Ubuntu and there is some things that are completely different from what I'm used to on Windows:

Wireless Adapter: Netgear RangeMax Next Wireless PCI Adapter WN311B

Additional Driver its Using: Broadcom STA wireless driver

Router: Netgear RangeMax

Information From "sudo iwconfig":

Code:

View 2 Replies View Related

Ubuntu Networking :: Access The Internet With A Netgear WPN111 Usb Adapter?

Feb 3, 2011

Is there anyway for me to access the internet with a Netgear WPN111 usb adapter

View 1 Replies View Related

Fedora :: Configure Bcm4313 Wireless Adaptor To Monitor Mode?

Sep 10, 2010

I wants to ask if there is any method to configure bcm4313 wireless adaptor to monitor mode.

I need to do this for my graduate project

till this moment, what I'm sure of is that ndiswrapper doesn't support monitor mode.

Is there any way to use monitor mode on this adaptor?

View 14 Replies View Related

Hardware :: Can't Put Atheros Based Wireless Card Into Monitor Mode

Mar 25, 2009

I like to test my network often. Until recently, I've been doing so on my old Ubuntu 6.06 laptop... the problem is It's too slow (1.06 GHz single Core ), and old, (designed for Win 2000) to really be effective any more. So, recently I bought a new laptop...one with a Dual core Processor, and twice the speed. Anyway, I'm running Fedora Core 10 X86_64 on it. My problem is as follows:

Although I do have MadWifi installed, for some reason, I still can't put my Atheros based Netgear WPN511 into monitor mode. (in the Network configuration window, it says "Atheros Communications Inc. Atheros AR5001X+" I'm not sure what it means but I'll put it in in case it helps) does MadWifi not work with Fedora? if not, is there a Fedora 10 (X86_64) alternative?

View 8 Replies View Related

CentOS 5 Networking :: Netgear GA311 Gigabit PCI Adapter

May 16, 2009

I have a Netgear GA311 PCI Gigabit Adapter. Any chance it might work with CentOS? It is not one of the cards listed when I do "NEW" Ethernet Adapter from the System Network menu. Maybe there is compatible choice?

View 5 Replies View Related

Security :: Remove Script Injection From .php And .html Files?

Mar 19, 2010

Our client-accounts were recently injected with the following script and since there are too many files that were injected (only index.php and index.html) how this script can be traced with a search command and removed in all files found.

[Code].....

View 9 Replies View Related

Networking :: Can Forward Packets Sniffed By Monitor Mode Wireless Interface?

Feb 9, 2011

I'm a student who is working on a wireless research project. I have a madwifi driver for Atheros chipset on Debian Linux. With having the wireless interface get into monitor mode, I want to forward the captured packets from the wireless interface to the other Ethernet interface so that a different computer which is connected to this machine via Ethernet receives those packets. I checked that alll packets are received in the wireless interface using TCPDUMP. I tried to forward those packets with IPTABLES like 'iptables -p FORWARD -i ath0 -o eth2 -j ACCEPT' However, I couldn't see any packets forwarded to eth2 using TCPDUMP.

View 5 Replies View Related

Ubuntu Networking :: Enable Wireless Injection?

Apr 13, 2011

How can I enable wireless injection?

[code]....

View 9 Replies View Related

Security :: Mod_security With CRS Adjustments To Capture Php POST Sql Injection Attempts?

Jul 22, 2010

currently I'm fiddling around with mod_security for apache2 configurations on CentOS boxes, right now in a test environment first (i.e. separate non production box).CentOS includes the mod_security "Core Rule Set" by Breach Security Inc, the devs behind that module.So far all's running mostly, logs/auditlogs etc.For simple testing, I made a small php form as following:

Code:
<?php
$link = mysql_connect("localhost",$user,$pass); //un/pw obfuscated for forum post

[code]...

View 1 Replies View Related

General :: Wireless Card Has Injection Enabled?

Jun 25, 2011

I am playing around with aircrack.

And was trying to see whether my wireless card on my laptop can pass the injection test

And I end up seeing the following... does it mean my wireless card is not able to run aircrack?

root@myubuntu:/home/myubuntu# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11bg ESSID:"" Nickname:""

[Code].....

View 1 Replies View Related

Ubuntu Networking :: Pacth Wireless Card Driver To Allow Injection?

Apr 14, 2010

i would really like to know how to patch a wireless card driver so that i can start injection in aircrack for example let's say we have an "Atheros AR5007EG" do you know where to find the driver patch for ubuntu and how to patch it ?

View 1 Replies View Related

OpenSUSE Wireless :: Aircrack-NG Packet Injection For Intel3945 Does Not Work?

May 14, 2009

I have the latest version of aircrack, and the latest compat-wireless package installed. When I try to inject I get this:

linux08:/usr/local/sbin # ./aireplay-ng -9 wlan0
16:46:33 Trying broadcast probe requests...
16:46:35 No Answer...
16:46:35 Found 0 APs

I know for a fact that there are 2 AP's. This worked perfectly with my old laptop with a D-link PCMCIA card.

[Code]...

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved