Ubuntu Networking :: Rt2870sta Driver - Transfers Slowing And Stopping Regularly

Jul 28, 2011

I have a tenda wireless adaptor running on 11.04 natty. The USB id is: 148F 3070

Using the already installed drivers rt2800usb it can connect to all 13 channels but is very flaky, transfers slowing and stopping regularly. The rt2870sta driver is a lot more stable, but it will only connect to channels 1-11, but I need to use channel 13 due to massive wifi congestion on other channels...

I've tried iwpriv but it says there are no ioctls for the device.

Is there any way to get the installed driver rt2870sta to scan and connect to channel 13?

I've also tried to install the latest drivers from the ralink website: rt2870sta says it can see all 14 channels, but fails to scan. I also tried rt3070 driver but I cannot insmod as there are errors...

View 9 Replies


ADVERTISEMENT

Debian :: Install RT2870sta Driver Without Any Internet Access?

Jan 11, 2011

First time user who has just picked up a nice old Sony netbook to give Debian a try on. Only problem is, this little thing doesn't come with any form of Ethernet card or port, and has to rely on a USB D-link DWA 140 B1 Rev Dongle. This device identifies itself as the Type RT2870 device and when i do "lsusb", it comes out as RALink RT2870. Running the CD install of Lenny, Kernel 2.6.26-2-686, and I can't for the life of me figure out how to get this damn Wireless card working.

The Wiki tells me to look into Upping the kernel to 2.6.32, which unfortunately requires some form of internet access for the backports Also consulted and tried (unsuccessfully, the make command would not run properly) this guy's advice: [URL].... Do any of you kind people have any advice or things for me to try to finally figure out how to get this little laptop online?

View 3 Replies View Related

Debian Configuration :: Configuring Wireless Network With Rt2870sta Driver?

May 14, 2011

I've been following this guide for squeeze: [URL] After getting the wireless-tools and firmware-ralink packages installed with no internet, I managed to installthe driver using modprobe rt2870sta (the 4th step). With the module loaded and the device plugged in (a RangePlusWireless Network USB Adapter with the WUSB100v2 chipset), iwconfig returned something like

[code]....

and then ifconfig wlan0 up returned ERROR while getting interface flags: no available device

View 14 Replies View Related

Ubuntu Networking :: USB Dongle Quarrels With Modules (rt2870sta)?

Oct 6, 2010

that's interesting for me. Ubuntu 10.10rc fresh installation, and Wireless Adapter based on Ralink RT2870.

[Code]...

View 4 Replies View Related

Ubuntu Networking :: RT2870STA Keebox Wireless Not Working?

Apr 30, 2011

I'm using Ubuntu 11.04 and can't get my new Keebox W150NU usb wifi chip to work. Using ndiswrapper, it crashes my computer almost every time I try to use it.

View 9 Replies View Related

Ubuntu Networking :: Rt2870sta / Rt2800usb / Ndiswrapper Not Working For Sitecom 300N Wireless(WL-324)

Nov 21, 2010

how to use the Sitecom WL-324 usb stick with ubuntu (10.10)? (It works with windows.)

lsusb | grep Ralink

Code:

Bus 002 Device 004: ID 148f:2878 Ralink Technology, Corp.Im using Ubuntu 10.10 x64 with a Phenom(tm) II X6 System My results so far:

sudo modprobe rt2870sta (or rt2800usb)

result (rt2870sta) :

lsmod | grep rt28

Code:

rt2870sta 445182 0
crc_ccitt 1699 1 rt2870sta
dmesg

[code]....

View 9 Replies View Related

Ubuntu Networking :: Why Does Wireless Speed Keep Slowing

May 13, 2010

I recently got karoo broadband installed, the speed is normally 8mbps but the longer I am connected to my router the slower it gets, I have to disconnect and reconnect to the router to get back to full speed, is this due to a bad wireless driver or do I need new drivers or a better router.

View 2 Replies View Related

Ubuntu Networking :: Wi Fi Keep Disconnecting Regularly?

Apr 28, 2011

i installed ubuntu 10.10 remix netbook edition on hp mini 110 last day. my wifi is working fine its connecting every network only problem is it cant keep its connection constant, i mean it keep disconnecting frequently. once it disconnect i tried to connect again but it connects but i can not surf internet.

View 1 Replies View Related

Ubuntu Networking :: Can't Do FTP Transfers

Dec 31, 2010

A little over a year ago I was using SCP to successfully transfer large files over my LAN (exact same hardware). I can't seem to do this any more, and I'm not sure why.I think it's either something with iptables, or a network card driver problem. I use the same driver for both computers (b43 wireless). I can't do FTP transfers either. They start going, but quickly stall. I've used the Firestarter (iptables gui) to allow all the correct connections.One last thing: When I tried to connect to ssh using an alfa wireless card (not sure of the drivers), I couldn't even connect to ssh period. Same settings were used.

View 1 Replies View Related

Ubuntu Networking :: NFS File Transfers Are Very Slow?

Jun 10, 2010

I have a server set up as an NFS share, and the share mounted on my laptop. Using linksys wireless g router and 15mb internet connection. Laptop is on wireless connection and server is wired.While transferring files from the laptop to the server I only get about 55kb/s. Is this normal for wireless g?

View 1 Replies View Related

Ubuntu Networking :: Wireless Connection Regularly Drops With Torrents

Apr 24, 2011

My wireless connection drops after a while when downloading torrents. I have to reconnect manually. Current configuration is Macbook Pro 5.5 with Broadcom card and Lucid. I've tried with Transmission and KTorrent. It's not a network problem as my Win laptop works smoothly and with higher transfers rates (i.e. 1MB/s in Win vs. 300KB/s at most in Ubuntu).

View 7 Replies View Related

Ubuntu Networking :: Wireless Connects Fine, Then Disconnects Regularly?

May 12, 2011

Wireless connects fine, then disconnects regularly. I thought it might be an issue with the rt2870sta driver, so I blacklisted it, and it uses rt2800usb now:

Code:
[ 13.625932] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 13.633139] usbcore: registered new interface driver rt2870

[Code]...

View 2 Replies View Related

Networking :: 3g Sim And Teracom-lw272 Device Not Activating Regularly

Nov 23, 2010

I am in kolkata zone, just bought the 3g sim and teracom-lw272 device. The problem is, its not activating regularly(its detecting, but some time, after Network Manager starts working, its failing ), and once its failed to get enabled, its unmounting the device all together....so i have to physically detach the usb device and reinsert. I have installed a rpm file that installed a script VKGEther....a small script file...but nothin else. Also, speed is very little(in [URL], it shows 0.1Mbps d/l speed) here some more info:

[Code]...

View 1 Replies View Related

Networking :: Slow File Transfers Using Samba?

Feb 2, 2010

I am running Samba on a debian Lenny box on a wireless home network. I find that file transfers to the samba share are very slow. It takes over a minute to copy a 40MB file to the linux box, but only 20 seconds to copy the same file to a windows XP box on the same network.

Anyways, I could use a little direction on how to proceed with this, I'm really not sure where to start,

View 9 Replies View Related

CentOS 5 Networking :: Slow Data Transfers W/ Smb, Scp?

Apr 14, 2009

I am having a problem with slow data transfers with both Samba and scp. I have gigabit NIC's on both all three machines that I am transferring to and from, connected to a gigabit switch. My data transfers under both smb and scp average around 21 MBit/s, (I am using nload to monitor transfer speeds).The machines are configured as follows,1) desktop

AMD Athlon 64 X2 6000+
6 gig Corsair memory
Realtek RTL8168C(P) gigabit NIC (on board)

[code]....

View 2 Replies View Related

Ubuntu Networking :: Large File Transfers & How To Set Up A Netbook Desktop Combo

Jul 11, 2011

I tried using ssh between my netbook and desktop, but it was going to take around 30 hours to transfer 39GB over the home network. Also SSH is very sketchy and often drops connections.I've been messing with it all day and I'm quite frustrated.What I'm looking to do is use my netbook as more of a primary computer and the desktop as a storage computer. Not quite a server, because I'd like to still keep a GUI on it. I'd like to be able to keep my music and movies on the desktop and stream them to the netbook (SSH sucks for this, always drops connections). I've already set up the web client for Transmission bit torrent client so I can torrent on a machine that's almost always on and connected.

Is there a better setup for all of this? I like the netbook because of the portability; I like the desktop because it's always connected (for torrents) and it has a larger storage capacity. It would be mainly used around the house. I would like to back up a file or two while abroad, but I'm not looking to stream music while I'm across town or anything.

View 2 Replies View Related

Networking :: Pure-ftpd Passive Transfers Not Working?

Jun 4, 2010

I have a dns-323 linux device that's running pure-ftpd with SSL/TLS authentication. Pure-ftpd is sitting behind a linksys router with IP 192.168.1.51. Pure-ftpd is configured for port 8021 and passive port range 55562-55663. The linksys router is configure to forward port 8021 and the passive port range to 192.168.1.51.

From outside my network I can connect to the ftp server using the WAN address of the router. I'm using filezilla 2.2.32 as my client and I choose FTP w/ explicit TLS (no other option will connect). The client will authenticate successfully with pure-ftpd but once it sets up the passive data connection and tries to do a LIST of the root directory, there's a timeout. I'm assuming this is because the passive data connection is not working. In pure-ftpd, I tried changing the passive address that it reports, to be the WAN address of the router, but it did not make a difference. I included the log from filezilla below.

[Code]...

View 5 Replies View Related

Ubuntu Networking :: Slow File Transfers (FTP, SCP) With Intel Gigabit Or Atheros WLAN?

Nov 16, 2010

I just installed ubuntu as my primary OS, but I have the disk with XP on it and I don't want to go back, but I need faster network connectivity. I have a T60p with Intel Gigabit jacked into my Gigabit router which also has my desktop (running XP) and my NAS. If I FTP files from my NAS (or SCP), I get transfer speeds around 250-500 KB/s (which is not very fast). On this same switch, from my XP desktop I get transfer speeds around 12 MB/s. I get the same speeds using my 802.11n card (Atheros) as with the ethernet NIC (250-500 KB/s).The drivers for the ethernet card and the atheros card are e1000e and ath9k respectively.I have disabled IPv6. Since the problem occurs using either interface, I am just going to concentrate on fixing it for the Ethernet interface (since I believe it to be a systemwide problem).

Code:

skinnersbane@albert:~$ sudo ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full

[code]....

Clearly my card is running at Gigabit, but why the bad transfer speeds? I am using filezilla for FTP (technically FTPES). I closed every other program. My CPU utilization does seem high and I wonder if this is part of the problem. I had no problems with throughput using either interface in Windows XP just one week ago.

View 1 Replies View Related

Fedora Networking :: Manager - Nm-applet Crashes Regularly - Disconnects Every 10 Minutes

Nov 23, 2009

With Fedora 11, I got NetworkManager, and it never worked right.. Right now, the nm-applet crashes regularly, no message nothing, just disappears from the panel. I wrote a two-liner to run it in an infinite loop. But my wifi also disconnects every 10 minutes. It's like clockwork, it just disconnects. I see things about "error 38" in the logs. I tried downgrading, upgrading, nothing helped.

[Code].....

View 7 Replies View Related

Networking :: Large File Transfers Start Fas Then Drop To A Crawl?

Jul 19, 2010

I need to transfer 330G of data from a hard drive in my workstation to my NAS device. The entire network is gigabit and being run with new HP procurve switches. All machines have static IP addresses. The NAS is a Buffalo Terastation PRO which has the latest firmware, is set to jumbo frames, and has just been upgraded with 4 brand new 500G drives giving us a 1.4TB raid 5 setup. My workstation is a dual Quad core xeon box running on an Intel S5000XVN board with 8G of ram. My OS is Ubuntu 10.04 x64 running on a pair of Intel X25 SSDs in a raid mirror. The data drive is a 500G SATA drive connected to my onboard controller. The file system on the SATA drive is XFS. This problem was ongoing before I got my new workstation, before we had the GB switches, and before the NAS got new drives. When I transfer a small file or folder (less than 500M) it reaches speeds of 10-11 MB/sec. When I transfer a file or folder larger than that the speed slows to a crawl (less than 2MB/sec). It has always been this way with this NAS. Changing to jumbo frames speeds up the small transfers but makes little difference in the big ones. I verified with HP that the switches are jumbo frame capable.

View 2 Replies View Related

Ubuntu Networking :: D-link DWA-552 Master Mode On 10.04 - File Transfers Or Bandwidth Consuming Processes

May 20, 2010

after successfully configuring the dwa-552 to work in master mode in ubuntu 10.04 (ath9k driver) I ran some file transfer tests. The download speed is very good (~50mbps) but the upload speed spikes at about 10-20mbps for the first few KB and then it's nonexistent (0-1kbps). This only affects file transfers or otherwise bandwidth consuming processes. Normal web browsing or ssh is not affected. After running a speedtest of my internet connection which is routed through the AP I could upload to the internet with 1mbps which is my inet connection maximum so apparently this is not affected. Tried the same file transfers with netcat to eliminate any other factors and had the same problem. dmesg and hostapd debug did not report anything unusual

View 2 Replies View Related

Ubuntu :: Boot Hangs On "Stopping Save Kernel Messages" Or "stopping System V Runlevel Compatib?

May 16, 2011

Boot of a new minimal system hangs on "Stopping save kernel messages" or "stopping system v runlevel compatibility". I have ubuntu minimal iso x86_64 from usb stick created with unetbootin (don't have a cd drive on the machine in question), and after that I didsudo aptitude install gnome-terminal network-manager-gnome gdm geditsudo rebootnever got a system back. Annoyingly I can't boot into the recovery mode either, and it seems the keyboard is only semi-responsive (i.e. many dead keys when at the grub menu).qualms about reinstalling, but I've done this a few times and ended up at the same place every time.

View 6 Replies View Related

Ubuntu Networking :: Stopping The Kubuntu To Setup An IP?

Mar 25, 2010

how do I stop my Kubuntu to set up an IP ? I tried this:

sudo ifconfig eth0 192.168.0.1

but in the following minutes it changes it!how do I stop it?

View 6 Replies View Related

Ubuntu Networking :: WUSB600N V1 Install On 10.04 - Iwconfig Shows Wlan0 With An ESSID:"" And Nickname: "RT2870STA"

Jan 6, 2011

I've been trying now for 2 days to get my WUSB600N v1 adapter installed on 10.04. I'm a bit of a noob but have been able to follow some posts on here on getting it set up. This is what I've done:

Installed the Ralink RT2870 drivers. Changed the config.mk to enable some parameters. Compiled and installed. Added some entries to blacklist.conf. Updated network/interfaces to include my wpa settings and passphrase. Restarted/rebooted/reinstalled about 100 times!

Here's what happens: iwconfig shows wlan0 with an ESSID:"" and Nickname: "RT2870STA" iwlist wlan0 scan shows my router fine (although does not show Cell 02 which should be the 5GHZ range). So basically it's not connecting to my router. Not sure if I missed any steps. Will gladly provide some extra output if needed. Pulling my hair out over this now ready to throw the adapter in the trash.

View 2 Replies View Related

Ubuntu Networking :: Wired Internet Stopping And Starting 11.04?

Jul 15, 2011

I have a bit off a strange one here, my internet stops and starts. One minute it is fine and the next it will not connect to any web pages or even to the router then its fine again. My machine is a new build Pc were I installed 11.04 as a fresh install, everything was fine till a few days ago when this all started up. I connect to my router via a wired network, the new PC also has a second HD with windows 7 on it and that is fine with the net so I know it must be some sort off software issue but I have not idea what.

Machine setup
Intel 3.3GHz i5 core
4 gig RAM
GeForce GT 220

[code].....

View 9 Replies View Related

OpenSUSE :: Stopping The Screen Saver And Stopping The Screen Locking?

Jan 23, 2011

In December I finally filled up my root partition and broke Suse 11.1. I therefore resized my partitions and installed Suse 11.3 on /root. I didn't not touch my /home partition.

I notice that when I leave my machine and come back the screen has locked. I have tried to turn off the screensaver, but it hasn't worked. I have Googled, but unfortunately the screen shots don't look like what I have and the instructions to stop this do not seem to match what I am seeing on the screen.

Is there a way to do this via the command line?

View 7 Replies View Related

Networking :: DHCP Works But The Service Keeps Stopping Every Few Hours?

Feb 2, 2010

Ubuntu 9.10 2.6.31-17-generic
ISC DHCPd version 3.1.2

The DHCP service starts fine on boot and with manual start then works fine for about 4-5 hours. After that it just stops on its own. I start the service up and everything works fine for about 4-5 more hours untul it stops again.

What do I need to do to ensure that the service will stay uo 24x7x365?

View 4 Replies View Related

Debian Installation :: Rosewill RNX-N1 (chipset Rt2870sta) Not Working?

Jan 19, 2010

I'm following this guide to get wireless working: http://wiki.debian.org/rt2870sta I'm on debian lenny x86 arch 2.6.30-bpo.2-686 I have debian-backports-keyring, linux-image-2.6.30-bpo.2-686, firmware-ralink, wireless-tools, wpasupplicant, (network-manager-gnome OR wicd) and their dependencies installed.

lsmod lists the module as loaded iwconfig lists the interface ifconfig up brings up the iface with nm-applet loaded, I CANNOT see any wireless networks, though I know there are several in range. with wicd, i specified ra0 (my wifi iface) as the wireless interface and I CANNOT see any wireless networks.

View 3 Replies View Related

Ubuntu :: Slowing Down Speed Of Movie Player

Nov 27, 2010

I have do some research by google to find out How To I slow down the speed when playing movie! And I found this: [URL]. But I not sure how can I do it!!

View 2 Replies View Related

Fedora :: Slowing Down My Mouse?

Mar 26, 2010

I have got my Fedora12 setup working just beautifully... except the mouse!

A few months ago I invested in a very nice, expensive high performance mouse with very high resolution tracking. In Fedora 12 it is just too fast for me though, and I'm already well on the way to Carpel tunnel syndrome..

I have turned the sensitivity and acceleration down as far as they go but it is still too fast. The old ways of adjusting xorg parameters are, I understand it, now null and void due to the hotplugging HAL framework.

How to turn the speed of the mouse down on Fedora if the control panel doesnt turn it down enough.

View 14 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved