Ubuntu Networking :: Error When Compiling Orinoco-0.15rc4.tar.gz - Wireless Extensions Are Not Enabled

Dec 26, 2010

currently running karmic on an old gateway laptop with kernel 2.6.31-22-generic and, as is par for how I handle challenges, I've jumped in with both feet - which is to say this is not a dual-boot situation. I've spent some time reading the forums (and other sources of information) and am grateful for all the knowledgeable people who are willing to share what they know.

My operating system seems to be functioning properly.I can get online via ethernet, but not via wireless. I have a lucent orinoco gold PC24E-H-FC (PCMCIA) card, which the computer isn't seeing. I am trying to follow the instructions here: [URL] to install the driver. Everything is going well until I get to the sudo make line. At that point I get the following display:

make -C /usr/src/linux-headers-2.6.31-22-generic M=/usr/src/orinoco-0.15rc4 KERNELRELEASE= modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.31-22-generic'
/usr/src/orinoco-0.15rc4/Kbuild:8: *** Wireless extensions are not enabled. Stop.

[code]....

how I can fix it so I can continue on with the instructions. (For the record - if I just continue on, I can change directory in the next line, but I cannot remove either hermes or orinoco as "no such file or directory" seems to exist.)

View 3 Replies


ADVERTISEMENT

Ubuntu Networking :: Wifi Configuration / Error No Wireless Extensions?

Jan 3, 2010

Hello, I have a problem with wireless internet on my laptop - Acer TravelMate 2413LMI with Broadcom BCM 4318 card.

Below are ifconfig, lspci and iwconfig outputs:

ifconfig:

eth0 Link encap:Ethernet HWaddr 00:0a:e4:e6:86:b5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:20 Base address:0x3000
lo
Link encap:Local Loopback
code....

I forgot to mention that the problem occured after linux 9.10 installation

View 1 Replies View Related

Ubuntu Networking :: Wireless - Lost It - 'wmaster0 No Wireless Extensions', But Then Refers To Wlan0 As The Wireless Connection

Mar 28, 2010

A friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.

Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:

1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.

2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).

3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.

[Code]...

View 7 Replies View Related

Fedora :: Xorg Extensions Initialized Versus Enabled

May 17, 2010

In Xorg.0.log, if you have an extension disabled in the configuration file, you will see: (**) Extension DAMAGE disabled In the first few lines ... however, later on you see (II) Initializing built-in extension DAMAGE So which is it? Is there a memory map or something I can dump and view to see which extensions are actually loaded into the X server? Is there a delineation between "disabled/enabled" and "initialized"? OK I found it:

xdpyinfo -queryExtensions | awk '{print; if (NF<=1) exit;}'

View 1 Replies View Related

Ubuntu Networking :: No Internet - LAN Or No Wireless Extensions

Mar 24, 2010

I have a fresh install of Karmic on a older compaq laptop. I initially had LAN access, but not wifi. I added a few Broadcom packages using synaptic, and then neither worked. Then I removed the same packages, but I still have no internet access, LAN or wifi. Here are some of my settings. vincentertainment@vincentertainment-laptop:~$ iwconfig

[Code]...

View 1 Replies View Related

Networking :: Intel 6050 Adapter - No Wireless Extensions

Jul 19, 2011

I have an Asus U52F laptop with the Intel 6050 network adapter.
Code:
# lspci | grep WiFi
02:00.0 Network controller: Intel Corporation WiMAX/WiFi Link 6050 Series (rev 5f)

I've downloaded the Intel firmware and dropped it into the correct location according to the README.
Code:
# ls -l /lib/firmware | grep iwl
-rw-r--r-- 1 root root 469780 Jul 10 13:18 iwlwifi-6050-5.ucode

I am using the current module from compat-wireless. When I modprobe iwlagn, I get no error message, and the module shows up in lsmod.
Code:
# lsmod | grep iwlagn
iwlagn 158054 0
mac80211 179615 1 iwlagn
cfg80211 139799 2 iwlagn, mac80211

However, no wireless devices show as being attached to my system!
Code:
# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.

I also see errors in dmesg.
Code:
# dmesg | tail
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
iwlagn: Copyright(c) 2003-2011 Intel Corporation
iwlagn 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:02:00.0: setting latency timer to 64
pci_resource_len = 0x00002000
pci_resource_base = ffffc90016384000
HW Revision ID = 0x5F
pci_enable_msi failed
iwlagn 0000:02:00.0: PCI INT A disabled
iwlagn: probe of 0000:02:00.0 failed with error -1

Distro: CRUX (64-bit contrib)
Code:
# uname -r
2.6.38.2

View 3 Replies View Related

Ubuntu Networking :: Iwconfig/iwlist - No Wireless Extensions And Interface Doesn't Support Scanning?

Mar 11, 2010

The adapter I purchased (Zonet ZEW2508 ) uses the Ralink 2070 chipset - a fact that originally excited me because Ralink seems to be fairly loving to the Linux community. However, despite my best efforts I can't get the thing to work. Initially I tried following directions to set up the driver you can download from the Ralink website. The directions I found were written February first, and Ralink updated the driver February eighth - so as far as I can tell the directions no longer work. After screwing around trying to figure that out for a while I decided to give ndiswrapper a go.

Initially this seemed promising. I just harvested the drivers from the CD and followed one of the many ndiswrapper directions available - most helpful seemed initially to be the Ndiswrapper Troubleshooting Guide found in this forum, however the solutions offered there didn't work either. When I throw an ndiswrapper -l into the terminal it looks promising at first, it tells me the driver is installed and the device is present, but it just doesn't work. When I try iwconfig, or iwlist scan it tells me "no wireless extensions," and "interface doesn't support scanning" respectively. The only devices even listed are lo, eth0, and pan0. There's no wlan0 or anything of the sort.

View 1 Replies View Related

OpenSUSE Wireless :: Error Compiling Dlink Driver

Nov 28, 2009

I downloaded the Dlink wireless G dwa-110 usb driver but I'm getting "rt73.ko failed to build. make[module]error 1" when compiling it.

I have installed the kernel-source and kernel-syms but I still get the same error. What am I doing wrong?

I'm running openSuSE 11.2 64 bit.

View 4 Replies View Related

Ubuntu Networking :: Wireless No Longer Enabled

Feb 22, 2011

About two days ago was when I was last able to connect wirelessly. I cannot recall a change I made to the system that would have caused this problem. Items to consider:

1. Under Network Manager, I am unable to click "Wireless Networks"
2. I ran the following code under in the terminal (sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | egrep 'acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|ound|p54|prism|rtl|rt2|rt3|rt6|rt7|usb|witch|wl'; iwconfig; cat /etc/modprobe.d/* | egrep 'acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl'; sudo hwinfo --netcard ; cat /var/lib/NetworkManager/NetworkManager.state; sudo lsmod) and proceeded to run enter BIOS where I enabled the Network Driver.

3. I am still unable to get the "Wireless Networks" to even be selectable under the Network Manager
4. When I return to BIOS, the computer shuts down immediately.
5. The start-up menu won't allow me access.
6. I have an HP G60-445DX notebook and an MCP77 Ethernet..

[Code]....

View 2 Replies View Related

Ubuntu Networking :: Wireless Networking Refuses To Be Enabled?

Nov 3, 2010

I have a compaq c784tu and it was shitty with xp. Vista is quite crap, so i turned over to ubuntu 10.4. The configuration of the laptop is: 1.73 GHz Intel Pentium Dual Core Processor T2370 with 1-MB L2 Cache, 533 MHz FSB featuring Intel Mobile 945GML Express Chipset Motherboard, 2-GB PC2-5300 DDR2 667 MHz SDRAM (Maximum 4-GB in 2 slots), a 160-GB SATA 5400 rpm Hard Disk Drive and 8x Super Multi Double Layer (8.5 GB) Slot-in DVD Writer.Everything worked like a charm and I was able to connect to the internet through a public wifi network. However, I came home this week to my mothers house, where they have a dsl-router to connect to the internet whih uses bridge mode pppoe. I tried to connect to the internet through it, and it initially couldnt. However, I got around that by doing a clean install of ubuntu. I was able to then connect to the internet using "sudo pppoeconf" and "sudo pon dsl-provider"One night the network manager app on the top left disappeared and would not come on. I figured I had fried my wifi adapter, however, lspci -v confirmed its presence.Further, "system>admn>system testing" detected the adapter aswell. I tried the iwconfig command in the terminal the result was:

lo no wireless extensions
eth0 no wireless extensions
wlan0 IEEE 802.11bg ESSIDff/any

[code].....

View 9 Replies View Related

Fedora Networking :: Orinoco Silver PCMCIA Wifi Card Doesn't Find Any Networks In F11

Sep 21, 2009

I have Lucent Technologies Orinoco Silver 11 Mbps PCMCIA wifi card. It worked perfectly in Fedora 10, but after updating to Fedora 11 it stopped finding any wireless networks. The updating were done with automatic updating utility. The card works perfectly in Windows, I tested it today.

My laptop is HP nx6110 if that matters.

Here is the situation:

When I plug-out the card, the Network Manager disables wireless networking as it should. When I plug-in the card, wireless networking is enabled, so the system seems to recognize the card in some way.

If I try to connect to "Hidden wireless network" (because there isn't any wireless networks listed in the Network Manager) system tries to connect for a couple of minutes, and then asks wireless settings again. Orinoco card's lights DOESN'T blink normally when connecting to the network (one light should blink rapidly and one should light continuously, but both are blinking rarely or doesn't blink at all).

In System->Administration->Network in tab Hardware (hope those names are correct, I use Finnish version of Fedora...) is:

It seems that the card is detected right.

Here is what I have done to get the problem solved: In System->Administration->Network I have tried to connect to the wireless network manually (disabling the Network Manager). I can't get the connection. It gives me random error messages, sometimes "Check the cable" or something like that, sometimes just timeouts IP determination.

I have tried to connect different wireless networks, no connection. All tested networks worked with another computer.

No matter if I reboot or service network restart or plug-out plug-in the card... the problem still appears.

Tried to find (and reinstall) drivers:

Code:

No Matches found

Code:

Here is the output of lspci. The output is the same if the wifi card is connected or not.

Code:

LAN connection is working just fine.

View 3 Replies View Related

Ubuntu Networking :: Wireless Not Works With Security Enabled?

Apr 8, 2010

I installed 9.04 clean yesterday to try and once again move from Windows to Linux and I thought I would give it a real try this time to learn the new OS. Well, right off the bat my wireless connection does not work. By default my WPA/WPK security was set on my router. My wireless adapter does connect to the router but there is no internet access. If I remove the WPA/WPK security and leave it open I can connect and I do have internet access but as soon as I re-enable WPA/WPK security I lose internet access. I even tried WEP security and same result. What the heck is going on with this? I am not going to leave my router unsecured but that seems to be the only way this works. I also upgraded this morning to 9.10 and same problem so this is not limited to 9.04.

View 4 Replies View Related

Ubuntu Networking :: Lucent Orinoco Silver Card Half Working In Dell Latitude C600 Laptop

Jan 11, 2011

am running ubuntu 10.10; Laptop see others network but its can't connect to my network. This card work under Windows XP.

View 1 Replies View Related

Debian Configuration :: Modpost Error Compiling Compat-wireless On Squeeze

Feb 3, 2010

Compiling latest compat-wireless on up to date squeeze install I get this:

make[1]: Entering directory `/usr/src/linux-headers-2.6.32-trunk-686'
Building modules, stage 2.
MODPOST 84 modules
Can't open file
make[4]: *** [__modpost] Error 1

[code].....

View 3 Replies View Related

Ubuntu Networking :: XPS 1330 Broadcomm 4312 With 9.10 - Wireless Not Enabled

Feb 2, 2010

1 ) Machine Brand and Model (PC/Laptop):

Quote:

Dell XPS 1330.

2 ) Wireless Brand, Model and Wireless Chipset:

Quote:

0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
Bus 002 Device 004: ID 05a9:7670 OmniVision Technologies, Inc. OV7670 Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

[Code]....

At this point, I have installed the STA driver for the device, though I have also tried with B43 (fwcutter). I have also tried with ndiswrapper with windows driver. All these cases, the end effect is the same.

I can see "Wi-fi" LED light up. When I bring up the KDE control module for networks, "Wireless" is disabled. However, when I right-click on the network manager icon on the taskbar, I see "Enable Wireless" checked on.

I am wondering if in the process of installing the ndiswrapprer drivers, I am messed up something?

View 5 Replies View Related

Ubuntu Networking :: Wireless Is Disabled On One Laptop And Enabled On The Other With Same Kernel

Aug 23, 2010

I just want to enable my wireless network card... how do I do that? It worked perfectly in Jaunty and it also worked when Jaunty was upgraded to Karmic, but in a fresh install of Karmic it is displayed as DISABLED:

sudo lshw | grep network:
*-network:0 DISABLED

I know this is not a bug in any kernel or anything. I now have Karmic on two identical laptops (Fujitsu Siemens AMILO, rt2500pci chipset) with the same kernel (2.6.31-22-generic). Wireless is enabled on one, disabled on the other. This is wearing me out... I am on the verge of buying Windows 7...

View 9 Replies View Related

Ubuntu Networking :: All Wireless Stops Working If Loopback Is Enabled In Router?

Jun 8, 2010

I'm running a Source Dedicated Server on my Ubuntu laptop, and to connect to it via external IP from other computers in the network I need to enable loopback in my router.This was working fine, but then I disconnected my laptop for a few days, and when I came back the wireless stopped working on my Xbox. I reset the router to factory defaults, and then setup everything again. It was all working fine until I enabled loopback again and power cycled my router. Now every time I do that, the internet on Ubuntu stops working and the wireless on the Xbox stops working.

Edit: You can ignore this I guess. It seems I was actually DISABLING loopback by enabling that router option, which I guess caused this. Strange, because the first time enabling this option was the only way to get my external ip to work. Oh well, everything is fine now.

View 1 Replies View Related

Networking :: SNMP Error - Encryption Support Not Enabled

Nov 1, 2010

When I run the following GET commad:
./snmpget -m ALL -M /data/net/naamab/snmp/snmp_mib/ -v 3 -a MD5 -l authPriv -u test1 -A welcome1 -x DES -X privpass 127.0.0.1 NOVELSAT-MODULATOR-MIB::nsModLineCMMode.0 -d

I get the error:
Encryption support not enabled.
snmpget: USM encryption error

I have defined a user (and user, view and access) that should work with encryption:
snmpd.conf:
createUser test1 MD5 welcome1 DES privpass
group debugGroup usm test1
view debugView included .1
access debugGroup "" usm priv exact debugView debugView none

General details:
I am using net-snmp on linux embedded
version 5.5
Configuration (part of it):
./configure --target=mips64-octeon-linux-gnu
--build=mips64-octeon-linux-gnu
--host=i686-pc-linux-gnu

message dump:
Sending 64 bytes to UDP: [127.0.0.1]:161->[0.0.0.0]
0000: 30 3E 02 01 03 30 11 02 04 1D 23 6A FA 02 03 00 0>...0....#j....
0016: FF E3 04 01 04 02 01 03 04 10 30 0E 04 00 02 01 ..........0.....
0032: 00 02 01 00 04 00 04 00 04 00 30 14 04 00 04 00 ..........0.....
0048: A0 0E 02 04 4C 08 7B B5 02 01 00 02 01 00 30 00 ....L.{.......0.

Received 118 bytes from UDP: [127.0.0.1]:161->[0.0.0.0]
0000: 30 74 02 01 03 30 11 02 04 1D 23 6A FA 02 03 00 0t...0....#j....
0016: FF E3 04 01 00 02 01 03 04 24 30 22 04 11 80 00 .........$0"....
0032: 1F 88 80 2D 53 AF 7D 00 00 00 00 00 00 00 08 02 ...-S.}.........
0048: 02 02 CF 02 03 01 11 C5 04 00 04 00 04 00 30 36 ..............06
0064: 04 11 80 00 1F 88 80 2D 53 AF 7D 00 00 00 00 00 .......-S.}.....
0080: 00 00 08 04 00 A8 1F 02 04 4C 08 7B B5 02 01 00 .........L.{....
0096: 02 01 00 30 11 30 0F 06 0A 2B 06 01 06 03 0F 01 ...0.0...+......
0112: 01 04 00 41 01 09 ...A..

View 1 Replies View Related

Networking :: Installing DLink Wireless Driver Or Compiling It?

May 24, 2011

How can I Install DLink wireless driver on Ubuntu ?

I had downloaded the driver . The file contains some files like MakeFile and ifcfg-wlan0 ,etc
+ a tar.gz file . which contains c or c++ source codes.

There are 4 folders also .

View 2 Replies View Related

Ubuntu :: Adding Extensions To Multiple Files Without Extensions?

Dec 28, 2010

I have a directory of a load of files without extensions. I know what the filetype should be, so is there any way of batch renaming the files to append a given extension onto it. i.e. text would be renamed as text.txt?

View 3 Replies View Related

Debian :: Using Internet But No Wireless Extensions

Aug 24, 2015

iwconfig

eth0 no wireless extensions.

lo no wireless extensions.

Whereas I am using wireless internet ...

View 14 Replies View Related

General :: Legacy Os No Wireless Extensions

Dec 24, 2010

I've been looking for info about Legacy OS but havent found much. I installed it and all works great except there are no active wireless extensions.My laptop have an internal wifi adapter (bcm43xx) I tried to load that driver using legacy OS network wizard but didnt work, the other is a external wireless card with a rtl8187 driver, this last one is the one I want to be up. I also tried to use ndiswrapper but can't set it up either.

View 1 Replies View Related

Slackware :: Iwconfig No Wireless Extensions?

Feb 22, 2011

I just installed Slackware 13.1 on my Asus 1215T, and I've been trying to get it to connect to my wireless network in my home. When I type iwconfig I get no wireless extensions, and ifconfig returns only lo, no wlan0. I read the Slackbook wiki and tried to configure the inet1.conf and wireless.conf but still no luck...

View 12 Replies View Related

Fedora :: Run The Command Iwconfig It Tells 'no Wireless Extensions'

Apr 9, 2010

I wanna see the wifi signal strength.But when i run the command iwconfig , it tells me 'no wireless extensions'.By googling I found that I need to enable config option CONFIG_NET_RADIO.I see that this has to be done in boot which has config files.So I typed the command grep CONFIG_NET_RADIO /boot/<config-2.6.31.5-127.fc12.i686> (my fedora version is 2.6.31.5-127.fc12.i686).But I got the error as "bash: syntax error near unexpected token `newline' ".I dont know the reason.I also want to know if I have to install driver(ndiswrapper)for viewing wireless signal strength.I thought that the drivers will present default(am not sure).

View 9 Replies View Related

Fedora Hardware :: No Wireless Extensions - System Impracticable To Use

Aug 26, 2011

A friend of mine have just migrated to Linux, and as recommended by me, He's trying Fedora 15 KDE. Everything runs just fine, he loved the OS, but there's a sad problem, his network card seems to have no "wireless extensions", which makes the system impracticable to use. I've tried searching around which card JMC250 is a single-chip PCI-Express Gigabit Ethernet Controller

with lspci
and which driver for this card
JME
is installed, with modprobe list

I've tried loading this driver with modprobe jme, no errors. And I've also tried compiling a driver I got from the manufacturer. No changes.

View 13 Replies View Related

General :: Asus Eee Pc 1001px Will Not Find Wireless Extensions

Aug 28, 2010

Just bought a netbook, ASUS Eee PC 1001PX, and got rid of the crappy XP pre-installed. first i put netbook remix on it, and tried many downloads and ndiswrapper to fix the wireless problem. then i went ahead and put another form of ubuntu on it thinking it might have the right drivers need to use the built-in wireless card, nothing. i dl all updates and bug fixes. i went to atheros to download the only driver they have for linux in the AR8132 class but still not helping. although i am not sure if i even installed. once dl it only extracted itself. i couldnt figure out how to run. if someone has this type of netbook it would be awesome. everything works on it except wireless and headphone jack. i know its just cosmetics but it would be nice if all hardware worked.

View 1 Replies View Related

OpenSUSE Wireless :: Can't Get To Work - Eth0 "no Wireless Extensions"

Jul 2, 2011

I just can't get my wireless to work so I can get started with learning Linux. Here is a bit info about my setup, I have tried it both ifup and Network Manager version 0.8.2-15.20

[Code]....

View 6 Replies View Related

Ubuntu :: Error: Syntax Error On Line 20 Of /etc/apache2/sites-enabled/portal

Feb 1, 2010

I am trying a release of Ubuntu has have run into a problem that does not make much sense. I am receiving the following error: Syntax error on line 20 of /etc/apache2/sites-enabled/portal: Invalid command 'ProxyHTMLEnable', perhaps misspelled or defined by a module not included in the server configuration
fail! I believe the modules required for this is apt-get install libapache2-mod-proxy-html and it shows under the available modules and it was enabled with a2enmod proxy-html.

The line from the config is ProxyHTMLEnable On. The release is the latest download with updates from, 32bit.

View 4 Replies View Related

Debian Multimedia :: Nvidia-glx Dpkg-divert: 'extensions/libglx.a' Xserver Error?

Feb 7, 2010

I just wanted to post this in the forums for anyone else that was having the same issue. I looked all over the internet for 4 hours and could not find a solution and finally figured out what to do. Maybe this will help save some time for someone else.

The ERROR:
Removing nvidia-glx ...
dpkg-divert: error checking `/usr/X11R6/lib/modules/extensions/libglx.a': No such file or directory

[code]....

View 4 Replies View Related

Ubuntu :: Getting Wireless - Wire Network To Enabled ?

May 16, 2011

just installed ubuntu 11.04 on my old laptop (Dell latitude XT), to experience this OS. But for some reason I cannot get online, both wired and wireless network are 'grey', and i cannot enable them. Even when I try to go online with a USB wifi dongle,I also cannot enable wireless. Enabling Networking is selected.

I include the information I collect and hope this will allow you to give me a diagnose on how to make my wireless work.

lspci, for the build-in card

Code:

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved