Ubuntu Networking :: Connect Using ETH0 And Then Seemingly Fails And Disconnects

Mar 29, 2010

A friend called me today and he explained to me that after his ubuntu install he was unable to connect to a wired Ethernet network. He says it trys to connect using ETH0 and then seemingly fails and disconnects. I have him run a if config and send me a pic. The very odd thing about it is He had a lot 5-8 INET6 address? The laptops is Acer extensa 4420

View 1 Replies


ADVERTISEMENT

Ubuntu Networking :: Wireless Sometimes Disconnects And Doesn't Connect?

Mar 9, 2011

I facing a really annoying problem. I download regularly during the night using Wifi. The problem is that because I'm away, the wireless just disconnects and the pop window shows up asking me to into the password. The password is already saved in the windows so I just have to click 'connect'ut I don't understand why does it disconnect and when it tries to connect it asks for password again!y doesn't it simply 'try' to connect without asking the password when it is already saved.

View 3 Replies View Related

Ubuntu Networking :: Alpha 2W Disconnects - Can't Connect To Any Network In Range

Jun 22, 2011

Working on ubuntu 10.04 on an IBM Thinkpad X61 laptop with an Alpha 2W wireless usb card on wlan0. Once in a while the wireless network disconnects and can't connect to any network in range (open, wep, wpa, wpa2). It looks like it's trying to connect but then asks for a password (even if allready given one) and if open just not finishing connecting and trying to connect to another network. Happends the same with wicd. Network card is working ok. Also with other computers. Drivers are installed correctly and power consumption management is off.

View 1 Replies View Related

Ubuntu Networking :: Slow Connections - Disconnects After 1 Min - Connect To Networks But Can't Surf

Mar 26, 2010

i have ubuntu 9.10 on a lenovo s10. i had my alfa awus036h and it worked fine no issues. except for having to reconnect every hour or so. anyway i got back track 4 final and installed it on usb with unetbootin. i started to use wicd and etter cap on it. and i made sure to turn off wicd when i was done then i went back into ubuntu (i didnt install bt) and i started to have problems like everyone else. slow connections ,disconnects after 1 min, and can still connect to networks but cant surf.

View 1 Replies View Related

Networking :: IP Alias Fails When Using Ifup Eth0:1?

Aug 19, 2010

I having a problem with my network. I'm trying to assign an IP alias of eth0:1 to eth0. If I use ifup eth0:1 is fails and corrupts the network. Making the network useless. But if I just enter 'ifconfig eth0:1 10.1.1.51', it work fine? My scripts look like these:

Code:
:network-scripts; cat ifcfg-eth0
NAME="System eth0"
DEVICE=eth0
ONBOOT=yes

[Code].....

View 2 Replies View Related

CentOS 5 Networking :: Fails At Determining IP Information For Eth0?

Oct 7, 2009

I have been running into network issues lately with my CentOS 5 (installed on AMD Athlon X2 - 64 bit machine about 2 years ago). It was able to connect to the network fine until yesterday when I installed more memory into the machine restarted it.

Upon restart, the boot up was paused at 'Determining IP information for eth0' step for a while and booted with out connecting to the network. I tried restarting the network (/sbin/service network restart), but this is the error message I continuously get: Determining IP information for eth0...PING xxx.1.226.1 (xxx.1.226.1) from xxx.1.226.83 eth0: 56(84) bytes of data

[Code]...

View 2 Replies View Related

Ubuntu Networking :: Can't Get Eth0 To Connect

Jun 22, 2011

I have a 10.04 box connected to a router with DHCP and wireless. Lathough it can connect through the wifi, I can't get the connection working with the ethernet cable (which is the one I wanna use by default).

Code:

I may add that it's the default auto connection, but I've also tried to create one manually setting the right ip address, gateway, etc, and attributing the same ip on the router to the MAC address of the card. I've also tried to edit manually the interfaces file, with no effect, or no good one at least. This log comes from a moment when nothing has been changed from the original 10.04 installation.

And I have connected a laptop to this very same cable, and the connection worked straight away...

View 1 Replies View Related

Ubuntu Networking :: Cannot Connect To Wired And Wireless In 10.10 It Tries To Connect But Fails?

Jan 10, 2011

in linux world and have recently downloaded and installed ubuntu desktop 10.10i cannot connect to both wired and wireless ethernet on my laptopit tries to connect but fails in 30 seconds , it says"disconnected" while i am able to connect to the same in windows i have broadcom 4315 and i have tried both fwcutter and ndiswrapper but the problem persiststhe device id is 14e4:4315

View 9 Replies View Related

Ubuntu Networking :: 7.10 - No IPv4 With Eth0 - Can't Connect To LAN

Apr 19, 2010

Current problem: fresh, clean install of Ubuntu 7.10 on known good hardware does not use/produce/get/have an IPv4 associated with eth0, so cannot connect to my home network for Internet access.

Background: Have been wanting to build and maintain a home file server for some time now. Have also been wanting some hands-on practice to help me progress from Noob to Intermediate, eventually advanced Linux Tech. (I have two decades of tech support experience, but only small fraction of that using command lines and almost zero Linux.)

Anyway, every time I download and attempt to burn a recent distro on my Vista Shuttle, I only end up making drink coasters and mini-frisbees. so I thought that I might have better luck if I used a Linux Workstation to download and burn a server distro.

That's where I an now. I took one of my fully functional WinXP systems offline, replaced the WXP HDD with an old 3.2 GB, dug out my 2008 edition Linux Bible, popped in the DVD that came with it, and installed Ubuntu 7.10.

Everything else seems to have progressed smoothly, but I cannot seem to get the onboard Via chipset ethernet controller to talk to the router. When I run "ifconfig" in Terminal, I see IPv6 info, but nothing for IPv4.

When I try to configure eth0, it doesn't matter whether I set it up for DHCP or static... nothing works.

Is there a command line tht I can use in Terminal to manually configure eth0 to use IPv4?

View 3 Replies View Related

Ubuntu Networking :: Auto Eth0 - Network - Won't Connect ?

May 2, 2010

Upgraded To Ubuntu 10.04 The Other Day. And when I first installed it everything worked great except for my sound card which I fixed. But there was no problem with connecting to my Router via an Ethernet cable. Then I updated the video card drivers, restarted my PC and it wouldn't connect. It would try over around 1-2 mins then tell me its disconnected. No green light activity on the router / network card either.

I've reinstalled fresh copies of Ubuntu a couple of times now, Hoping to get the default settings back. But nothing has worked since.

I looked around the net and found quite a few people had this problem on previous versions of Ubuntu but it would seem most of there fixes were for there Version, so it hasn't helped me.

Heres some info:

ifconfig:

I've tried all the various things from dhclient to ifup/ifdown etc etc.

View 9 Replies View Related

Ubuntu Networking :: Eth0 Active But Can't Connect To Internet In 10.04?

Jul 16, 2010

i was using ubuntu 9.10 till recently when i decided to upgrade to ubuntu lucid 10.04. turns out the internet icon shows connected after fresh installation but when i try to use firefox , after an long wait it shows server not found. i did a research of my own and found that i am not able to ping even my router.using sudo dhclient eth0 doesn't recieve offers , but surprisingly when i tried dhclient eth0 in root shell with networking internet got configured very quickly and i can ping the router and any website.i forgot to mention i have a wired connection which i am trying to connect and the net is working fine with windows 7 on the same PC.

View 2 Replies View Related

Networking :: No IPv4 On Eth0 - No Connect To Router

Apr 20, 2010

I have tried clean installs of Knoppix v0.6, Xandros 2.0, and Ubuntu 7.1... same issue with all. I cannot seem to get eth0 (via chip on mobo) to get/have/use IPv4. ifconfig shows only IPv6. (I cannot paste any info because linux desktop is on different box.)

End result is that I cannot get the linux desktop to connect to my lan, either with dhcp or with static ip.

I have a belkin router configured as my gateway 192.168.3.1 and nothing fancy with the setup. I have dhcp open for 192.168.3.245 thru ...254 and at most there are only 4 systems in home connecting with dhcp at any time. all other systems have static addresses.

I have two decades of desktop and lan support under my belt, but relatively small amount of command line experience and almost no history with linux (unless you count a dozen unsuccessful attempts to burn linux distro install discs on this Vista desktop).

Therein lies the start of my prob. I need to build and manage a fileserver for my home, but cannot seem to get a working installer cd or dvd to burn from anything I download.

So I said to myself, "Self," I said, "you're a tech. Build a workstaion, use the DVD that came with your Linux Bible (2008 Ed.) to install one of the linux distros on it, then download a recent, stable server distro and burn it using the linux workstation."

Unfortunately, if I cant get an ipv4 connection to my home network, I cant get out to the Internet to download any newer ISO files.

So what am I missing or doing wrong? How do I tell linux to stop trying to use IPv6 and let me use IPv4?

BTW, eth0 works just fine if I install Windows on that PC, so I know its not bad HW. Could it be a driver issue? Or do I need to use some Terminal command to turn off IPv6 and reconfigure eth0 for IPv4?

View 5 Replies View Related

Networking :: Need To Connect Broadband Internet Through Eth0

May 24, 2011

I am having broadband connection, I need to connect broadband internet through eth0. Please give me some use full information for configuring this.

View 6 Replies View Related

Ubuntu Networking :: Can't Connect To The Internet With Ppp0 While Eth0 Is Active

Jul 2, 2010

My machine has Ubuntu 10.4, installed a week ago. I'm connecting to the Internet with a Wireless 3G modem, the interface is named ppp0. Additionally, I have a network card that is connected to a home router, that's eth0. Everything works fine with eth0 disabled, all my apps can access the internet correctly. But, my issue is that when i enable eth0, i can't access the internet with any app.

So why do i need eth0 anyway? The thing is that i must share my internet connection with my sister, who is also connected to our home router. I planned to give her access by installing squid on this machine and configuring her browser to connect to squid. However, since none of my apps can connect to the internet while eth0 is active (whereas squid and all other apps work fine with eth0 disabled) I can't let her connect to squid while squid is working correctly.BTW selecting "use this connection only for resources on its network" under "routes..." of the ipv4 tab of "Auto Ethernet" made it a little better. Firefox and Xchat started to work with eth0 active. Squid still doesn't work though (althought it works just fine with eth0 disabled)

View 4 Replies View Related

Networking :: Multiple Ethernet - LAN - Cant Connect To Both The Eth0 And Eth1 At The Same Time

Dec 12, 2010

I have 2 LAN ports. one from the motherboard (on board) and the other from a lan card i bought a few days back. one is use for browsing the net, the other for a media player.

problem is i cant connect to both the eth0 and eth1 at the same time. i have to disconnect one of them to connect to the other. and this really gets irritating as it doesnt always work as flawlessly as it should. what am i doing wrong?

Output of "ifconfig":

Quote:

I'm on ubuntu desktop 10.10 64 bit.

View 8 Replies View Related

CentOS 5 Networking :: Fails At Determining IP Information For Eth0 (onboard NIC Asus P6T On Centos 5.3)?

Apr 28, 2009

I'm running a fresh install on an intel i7 system on an asus p6t deluxe v2 motherboard with the onboard NIC (Marvell Technology pci-e). I know the NIC is working as when I boot into the onboard OS that Asus provides (Asus Express Gate SSD)I have a working net connection.Booting up CentOS hangs at determining IP information for eth0 and eventually fails with the following error:PING xxx.170.30.1 from xxx.170.31.231 eth0: 56(84) bytes of data---xxx.170.30.1 ping statistics ---4 packets transmitted, o received, +3 errors, 100% packet loss, time 2999ms, pipe 3 failed.

RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.

[code]....

View 14 Replies View Related

Ubuntu Networking :: Wireless Connect Fails At WEP Key?

Oct 19, 2010

Dell mini 10 with ubuntu 10.04/windows xp, connecting to linksys wrt54g. Connected when I was using 9.10, has worked for several months since 10.04 was installed. Still works if I boot XP, but, when booting Ubuntu, router won't accept the passkey which I obtained from my wired computer. I've glanced through a bunch of posts and see several which are close, but no solution. Only cause that I can think of might be a shut down while connected. I say that because it was working and I had no need to change settings.

View 5 Replies View Related

Ubuntu Networking :: First Attempt To Connect To Wireless LAN Always Fails?

Jun 24, 2010

The nm-applet starts automatically as it should, and also tries to connect to the local, wireless LAN, but always fails its first attempt. If I click the icon and ask nm-applet to connect again, it always succeeds.

The server, running the wireless LAN, never sees the first attempt to connect, so no wonder this attempt fails. But it would be nice to make it succeed!

View 2 Replies View Related

Ubuntu Networking :: Wireless Can See Networks But Fails To Connect

Jun 30, 2010

I have an Atheros AR242x card. It can see my wireless network (WPA2). When i attempt to connect to the network it asks for the WPA2 passphrase. After entering the password it begins connecting but hangs up for about 3 minutes before saying wireless disconnected. The wireless worked for one day on a fresh install (Ubuntu 10.04)and then started doing this.

View 2 Replies View Related

Ubuntu Networking :: RTL8187 WiFi Fails To Connect On 10.04?

Jul 10, 2010

My Realtek RTL8187 Wifi fail to connect using WPA security. The authentication window shows up repeatedly every time I try to connect. Please note the password is correct. I searched and haven't found a conclusive solutions as of yet.

View 1 Replies View Related

Ubuntu Networking :: Fails To Connect To Wifi From Phone?

Sep 9, 2010

Has anyone else experienced a failure to connect to a mobile network. I have root access wireless tether on my Droid X and I can't seem to connect to it. It times out. My buddies windows box can, and his Iphone will as well. I can see the network just fine, just no connection. Tried changing frequencies as well. And restarting both the phone and laptop.

View 3 Replies View Related

Ubuntu Networking :: Unable To Detect Router - Tries To Connect But Fails?

Apr 24, 2010

Ubuntu 9.10 comes with rt2870, the driver for my Zonet ZEW2545, and I have had to blacklist rt2800usb in /etc/modprobe.d/blacklist.conf in order for rt2870 to work. My network adapter is able to attempt to connect to my router, but after 10-40 seconds it tells me I am disconnected again. This adapter works fine on windows.

View 1 Replies View Related

Networking :: Eth0 Fixed IP - Eth1 DHCP Gateway - Access To Eth0?

Aug 19, 2009

5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.

I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.

Code: echo !HH | nc 192.168.1.6 80

I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?

View 17 Replies View Related

Networking :: Production Server With Static IPs On Eth0 And Eth0:1 - Getting Private LAN On Eth1?

Jul 1, 2010

I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.

My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...

The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2

Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...

I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).

View 10 Replies View Related

Ubuntu Networking :: Fails To Connect Vostro 1720 To Wireless Router?

Oct 7, 2010

I'm trying to find out why the wireless access point at work most of the time won't let me connect to the network. I'm using Ubuntu 10.04 on a DELL vostro 1720. The router model is D-LINK DIR-655. lspci gives me: Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01), and I'm using Broardcom STA drivers.

If I try like 10-20 times to connect I will often finally get connected and once connected everything works fine for the rest of the day. The only router I'm having this problem with is this one. In the log below, the last lines is a connectionattempt that succeeded and all the lines above those are several attempts that failed. It seemes like there is some kind of timeout issue but I'm not sure what and how to fix it.

The syslog for the connection attempts are (I have marked out MAC adesses and public ips with *):

[Code]....

View 3 Replies View Related

Ubuntu Networking :: Dell Inspiron 640m Wireless - Fails To Connect

Jan 22, 2011

Dell Inspiron 640m laptop, running 10.04. It previously connected via wifi & now fails to connect, although the wireless indicator shows a connection. Connection via ethernet works. Below there's some information that looked like might it be useful to diagnose the problem based on other posts in this forum.

[Code]....

View 2 Replies View Related

Fedora Networking :: Trying To Connect To VPN Server / VPNC Fails?

Jan 6, 2011

I have been trying to connect to my University's VPN Server and for some reason vpnc fails. I have configured the vpn settings the same way I did for the past two years. They worked properly on Fedora 12 and 13, but for some reason fails on Fedora 14.

Code:
Jan 6 16:45:20 exodusprime NetworkManager[1269]: <info> Starting VPN service 'vpnc'...
Jan 6 16:45:20 exodusprime NetworkManager[1269]: <info> VPN service 'vpnc' started (org.freedesktop.NetworkManager.vpnc), PID 11731
Jan 6 16:45:20 exodusprime NetworkManager[1269]: <info> VPN service 'vpnc' appeared; activating connections
Jan 6 16:45:21 exodusprime NetworkManager[1269]: <info> VPN plugin state changed: 3
Jan 6 16:45:21 exodusprime NetworkManager[1269]: <info> VPN connection 'Swinburne University VPN' (Connect) reply received.
code....

View 4 Replies View Related

Networking :: Only Firefox Fails To Connect In Some Networks Using Fedora 14?

May 23, 2011

In all but one place my HP Pavilion laptop running Fedora 14 will work flawlessly to use the Internet for e-mail, ftp, http, etc. In one network there is a wireless router - Cisco/Linksys E3000 - that allows every computer to use the Internet normally for wireless or for wired connections, every computer but mine. If I use Google's Chrome I can access the Internet. I can ping any web site too, but the moment I try to access anything with Firefox 3.6.17 there is a long delay and the standard error page appears. Weather or not I use a wired connection is apparently irrelevant.The Windows 7 computers in the same network are free of this curious problem. Strangely I have noted a problem like this, possibly the same problem, with another network at a coffee shop and they both share the misfortune of using AT&T, which is proud to not support Linux ... for customers of course (it's good enough for themselves I'm sure)

View 3 Replies View Related

Networking :: Ignoring The Unknown Interface Eth0=eth0?

Dec 18, 2010

I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.

ifconfig eth0:

Code:

eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

[code]....

View 3 Replies View Related

Fedora Installation :: Install Fails: F14 Can't Bring Up ETH0?

Mar 7, 2011

Installation fails part way-in , prelim formating of drive is ok, Failure comes when network connection is require to continue. The Marvell 88E8056 PCI-E gigabit Lan Controller is correctly listed but network manager fails to bring it up. when I put the old F10 drive in , everything boots up , I can surf the web.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved