Ubuntu Networking :: Wireless Does Not Work After Switching To 10.04?

Sep 23, 2010

Toshiba A215-S5849

Atheros 5001 card. Windows reads it as 5007eg. Wireless runs slowly or not at all. Wiki says that atheros should work out of the box. Am I doing something wrong?

View 1 Replies


Ubuntu Networking :: Switching Between The Wireless / Wired?

Nov 15, 2010

I have a single pc with both a wired and wireless card in it. I want to take down the wired connection down and bring the wireless connection up with a cronjob at certain parts of the day.

Here are my interfaces:


eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:xx
inet addr: Bcast: Mask:
inet6 addr: fe80::224:1dff:fe64:ecfb/64 Scope:Link


Same error applies if eth0 is down and I try to bring it up, I get the same error.As a side note, here is my networking hardware:


00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2)
01:06.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)

View 3 Replies View Related

Ubuntu Networking :: Wireless Don't Work On Wireless 1390 WLAN Mini-card

Mar 30, 2010

I have a dell 1521 and I can't get internet working, I thing the driver is no working with ubuntu 9.10

View 1 Replies View Related

Ubuntu Networking :: Wireless The Trial Mode Is Working Great, But The Wireless Will Not Work?

Jul 21, 2010

I want to switch my laptop from XP to Ubuntu, but right now, i cant risk installing it. i dont want to have it partitioned so i can dual boot, so for now i only run the try-it-out mode.Before i consider installing though, i want to see if i can get everything to work ahead of time, that way im not regreting instalation. I have a Compaq Presario V2000 laptop, with 55GB hard drive and 516MB ram. So far, the trial mode is working great, but the wireless will not work. Ive tried to install the driver, but i am unable to do so. I have looked this up, and i have tried many things, and so far, none have worked.I was wondering if it was just part of the trial thing or not, but it is a Broadcom Wireless BCM4318 driver

View 9 Replies View Related

Ubuntu Networking :: Wireless Internet Drivers Cannot Get Wireless To Work?

Mar 20, 2010

i installed ubuntu along side of xp, and i cannot get my wireless to work. the drivers that are installed in xp work great, and i can access the internet, but do not work in ubuntu.

View 3 Replies View Related

Ubuntu Networking :: Belkin Enhanced Wireless USB Network Adapter - Windows Wireless Drivers App Doesn't Work

Feb 3, 2010

I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:


View 1 Replies View Related

Fedora Networking :: Doesn't Work After Turned Off Wireless By Pressing A Wireless Button On Laptop?

May 19, 2011

Recently I have installed Fedora 14 on my other laptop. It's a dual boot with Windows 7. Everything worked perfectly fine, networking included, until my friend didn't accidently turned off the wireless by pressing a wireless button on the laptop. Since then the wireless on Fedora doesn't work. It does on Windows thought. I've tried restarting the laptop few times, but the wireless still doesn't want to work again.

View 2 Replies View Related

Networking :: Can't Get Wireless To Work With Intel Wireless 5300 AGN

Aug 21, 2010

I can't get my card Intel Wireless 5300 AGN to work. I'm running Slackware 13.1 and it's a full, fresh install.I get to show up with lspci -v:Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection...But it will not show up with 'ifconfig' which will only list the local loopback (yes we have have a eth problem as well but one thing at a time).

View 5 Replies View Related

Fedora :: VT Switching Doesn't Work?

Aug 28, 2010

For some reason Ctrl+Alt+Fn doesn't work on my Fedora 13 workstation using the nvidia driver. I specified the following in my xorg.conf but it doesn'tption "DontVTSwitch" "off"It is probably not even an Xorg problem because VT switching doesn't work in runlevel 3 either.

View 4 Replies View Related

Ubuntu :: How To Stop Current Window Following Me When Switching Work Space?

Aug 6, 2011

I would like to know how I stop the current window I am on following me when I switch workspace.for example, I have this web browser open whilst I am typing this, I press Ctrl+. (my shortcut to take me to the workspace to the right), and instead of taking me to what was a nice empty workspace on the right, it sweeps this web browser to it as well.I can't find a way to configure this to my liking, can anyone help?

View 4 Replies View Related

General :: Switching Init Levels Does Not Work?

Jan 21, 2010

I have CentoS 5.3 and switching init levels does not work.when I login console mode,doesnot work ctrl+F7 key...and on the contrary.when Im in graphical mode, does not work ctrl+F1...ctrl+F6 keys.

View 4 Replies View Related

Ubuntu Multimedia :: Sound Doesn't Work After Switching From Pulse To ALSA

Oct 16, 2010

I have made a pretty sizable mistake. I was trying to figure out why my game was having sound issues when I was told to update my sound drivers. After a bit of searching, I came across this website. I downloaded and ran the script in the first link. Minor problem: I was using PulseAudio, not ALSA. Needless to say, the script didn't work. After the machine rebooted, I had no sound at all. I was planning on switching to ALSA anyway, so I found this thread and ran the following commands:


View 9 Replies View Related

Fedora :: Nautilus Doesn't Work After Switching From KDE To GNOME

Jan 20, 2010

I recently switched my desktop environment from KDE-4.3.4 to GNOME-2.28-2 and I did that by installing most of the gnome-packages and uninstalling pretty much all of the kde-ones. After reboot everything worked fine except the file browser that doesn't seem to care about my feelings. It launches and when I try to kill the process the status changes from sleeping to uninterruptible and then back to sleeping. The only way is to reboot but that isn't a solution.Error while sending message: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.

View 14 Replies View Related

Fedora Networking :: Enable Wireless Networking Does Not Work In Windows?

Jun 20, 2009

I've been experiencing a problem with Fedora in which when I enable Wireless in Fedora, Wireless networking does not work in windows. HOwever, when disabled, it works correctly. Windows claims it is "not able to find any networks to connect to"

EDIT: It seems that when wireless is disabled manually on fedora before shutdown, there are no problems in windows.

View 14 Replies View Related

Ubuntu :: Getting X To Work After Switching From Onboard Intel Video To A 5000 Series ATI Card?

Apr 25, 2010

I'm having trouble getting X to work after switching from onboard intel video to a 5000 series ATI card. Apparently I need to switch to a MESA or fglrx driver. I did a sudo apt-get install fglrx-driver and it installed but still no X. I'm currently using Karmic. I've tried to boot with a live CD which works fine and changed the xorg file manual but that was a mess.

When I start I get a checking battery state ... done and it stays there forever sometimes and sometimes I can login but without x. Typing startx gives me a long list that says check the xorg website. I've been looking around for a way to fix this and haven't been able to get it working.

View 6 Replies View Related

Ubuntu Networking :: How To Get My Wireless To Work

Jan 11, 2010

How to get my wireless to work. I'm currently running Ubuntu 9.10 on a Dell Inspiron 2200. The wireless adapter I'm currently using is a Linksys WPC54G ver. 3.

When I enter iwconfig lo, eth0 and wmaster0 have no wireless extensions. wlan0 says

I tried following the instructions here:[url]

But when I enter sudo ifdown eth0 it says internet eth0 not configured. then wlan0 it acts like it doesn't even exist.

View 1 Replies View Related

Ubuntu Networking :: Wireless Will Not Work At All

Feb 10, 2010

I'm very new to Ubuntu and Linux in general. I installed Ubunutu NBR on a HP Mini 2140. After some wireless issues and a bad decision, I deleted the ssb.ko files. Now the wireless won't work at all. How can I repair the SSB modules or reinstall those files?

View 1 Replies View Related

Ubuntu Networking :: Can't Get Wireless To Work At All

Mar 6, 2010

I've installed Ubuntu 9.1 on my Acer Aspire One ZG5 that was previously running Win XP with the wireless working fine. In ubuntu,though, i can't get the wireless to work at all and I don't really even know how to troubleshoot it. I've opened a terminal and used sudo to update various packages, but still nothing. It does appear as though the system recognizes the card since I can configure it, but I'm not keen on playing wi8th the BSSID and MAC address stuff because I just don't have any confidence that it will change my situation. Has anyone had any success with this setup (ubuntu 9.1 and acer one)? Is there a step-by-step wireless troubleshooting/ configuration process that's generic to ubuntu?

View 8 Replies View Related

Ubuntu Networking :: Can't Get Wireless To Work?

Apr 6, 2010

Let me start off by saying that I'm a complete Linux-noob. I just installed Ubuntu 9.10 and I'm really enjoying it. I was planning to install it for quite a while now but now that I have my own computer, I actually could make it happen.That being said, it's a whole difference with Windows though and sometimes it's hard to find my way in this new system. My main problem is that I can't seem to get my wireless connection working. From what I've read online this problem is not uncommon with Ubuntu 9.10?

I tried searching for my wireless card drivers in 'System > Administration > Hardware Drivers' but that didn't really work out. It did find a wireless card driver but when I try to activate it, it returns an error message. All the other drivers seem to be installed so I can't really see what the problem is. Can anyone help me with this?BTW, I think I also have a problem with the graphics card driver. When I try to active the 'extra' desktop effects is says this can't be activate. I already tried installing Compiz and the Composite Manager.

View 1 Replies View Related

Ubuntu Networking :: Can't Get Wireless To Work At All?

Aug 4, 2010

I've installed Ubuntu 10.04 on a computer I can't get the wireless to work. I looked into it, and I believe the problem is that I don't have the right driver to work with the wireless card, but I wasn't able to tell what my wireless card is properly. And when I got the bcmwl-kernel-source package and installed it, the driver still didn't appear under "hardware drivers". Compounding the problem, I can't use any sudo commands for some reason because when it prompts me to enter the sudo password, the keys other than "enter" don't seem to work. I probably don't have the right information up there.

View 1 Replies View Related

Ubuntu Networking :: Wireless Does Not Work

Aug 29, 2010

my friend loves ubuntu but he doesnt want to switch because he wireless doesnt work he entered all the right details wpa 2 personal and the key but he did not pick up

View 1 Replies View Related

Ubuntu Networking :: Wireless Does Not Work?

Jan 30, 2011

ok i have yet to get my wireless driver to work and thats one thing. this is what i have in my computer

00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)


View 8 Replies View Related

Ubuntu Networking :: Can't Get Wireless To Work.

Feb 28, 2011

I have a problem with my laptop's wireless card. My laptop is Grundig GNB-250D. According to lspci my wireless card is a "Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 43)".

I can browse the internet just fine if I use an ethernet cable. Also the card worked perfectly on Windows Vista. I tried installing the drivers using Ndiswrapper and it didn't seem to work By the way I followed this guide: [URL]

View 1 Replies View Related

General :: Losing Wireless Connection After Switching Back To Vista OS

Feb 17, 2011

I have Ubuntu 10.10 installed. I am very new to Linux. I am having a problem connecting to wireless network when I reboot to Vista OS. When I am using Ubuntu, it works fine. I have to plug in the LAN cable in order to connect to internet. When I try to connect to wireless network, I don't see any networks at all. My WiFi switch is ON. I keep switching back and forth between Vista OS and Linux.Narendra

View 1 Replies View Related

Ubuntu Networking :: Can't Get Wireless Card To Work

Jan 26, 2010

I have been messing around with ubuntu for a few hours now trying to get my wireless driver to work, but I am having no luck. It seems like I installed the driver right, and network-admin use to show the wireless, but I couldn't unlock it to mess with properties. Now it doesn't even show wireless, and I still can't unlock it, so I'm unable to get my wireless card to work.

View 9 Replies View Related

Ubuntu Networking :: Cant Get Wireless Connection To Work

Jan 28, 2010

I installed Ubuntu and I cant get my wireless connection to work. I found that I need ndiswrapper to update my drivers following the sticky post in here. However there is a problem, because I cant successfully run ndiswrapper on my system.

View 9 Replies View Related

Ubuntu Networking :: Router Won't Work On Wireless?

Feb 18, 2010

last night as a download was going the Internet just stopped connection. Then asked me for the WPA & WPA2 personal password. I didn't know what to put since I had already tried multiple pass words I restarted the router.Now for some reason the computer won't pick up the router wireless signal. It picks up multiple connection's around my area so I know that it's not the wireless card. The router is connected via ethernet at the moment so I know the internet works.Do I have to find the ssid? Maybe the router reconfigured it's self when I restart it and broadcasting mode turned off... I just don't know

View 9 Replies View Related

Ubuntu Networking :: Wireless Does Not Work - Ipw2200

Mar 3, 2010

I have been trying for months to get my wireless working on my acer laptop and I am now beyond despair. I using an Acer Extensa 67000 and here is what is at issue:

ubuntu@ubuntu:~$ lspci -nn | grep 'Wireless'
06:04.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection [8086:4220] (rev 05)
ubuntu@ubuntu:~$ lspci -vn On this one I posted just what I thought would be relevant:


View 3 Replies View Related

Ubuntu Networking :: Can't Get Sabrent Usb 2.0 Wireless-N To Work

Mar 21, 2010

I just installed Ubontu 9.10 and I am a first time user. I am attempting to run my Sabrent usb 2.0 wireless-N ieee 802.11n device with Ubontu but I cant seem to figure it out. I can not access it as a regular usb device and I can't access the installation driver. The device loads up an installation screen when I use it on windows so I know its not the device. Not sure how to install it or to get it to run from here.

This is what I have done thus far:

lsusb -ID 148f:3070 Ralink technology

View 1 Replies View Related

Ubuntu Networking :: Wireless Card Won't Work With 10.04

May 27, 2010

I have a Dell inspiron E1705 that I recently installed 10.04 LTS on. The wireless card i'm using is a Belkin express card that worked perfectly fine with 9.1 but won't work with 10.04. lspci -v output shows the card as installed with a driver listed but under capabilities is says "access denied".

View 9 Replies View Related

Copyrights 2005-15 www.BigResource.com, All rights reserved