I installed a Tenda W322P wireless card in my dual-boot PC running both Windows XP and Ubuntu 11.04. The card worked straight out of the box on XP, but does not function correctly under Ubuntu. My apologies for any missing/irrelevant information, I am having to post this from the Windows boot so the Ubuntu settings are not directly available at the same time as internet access.I followed the process detailed here htURL...to install and configure the driver (I believe from reading other sites that this card is the Ralink RT3062 chipset), blacklisted the original RT2860 driver that was in use (couldn't even get the card to scan for wireless networks with the default driver) and restarted the interface.
Since then, sudo iwlist scan can find my wireless router but when I attempt to connect to it, it seems to enter a loop of requesting the WEP key then pausing for a while before re-requesting the key. I know I have the key value correct because it is copied and pasted from the same text file I used to copy and paste into the passkey field on the Windows boot. Attempting to connect to the router using Ubuntu also has the rather unfortunate side-effect of crashing the wireless router, killing off all other device connections until the router has been reset.
I am using 11.3 (64-bit gnome) and have a new Tenda w322p wireless n card, this works absolutely fine under windows, but I also bought it due to reviews saying it worked with linux. The card appears in network settings as RaLink WLAN controller and uses kernel module rt2800pci, I have also tried typing in the network ssid etc manually but it hangs on exiting network manager (will post what it says later, after writing this) I used drivers from here:Ralink corp., and used the rt3062 one(5th one down?)
Those are my authentication capabilities, obviously. I am using a WEP encryption for my wireless router and according to this, it will not allow me to connect. Is there anyway to allow that? The wireless card works just fine in Windows, even on the same network encryption type. Using a Intel Wireless/Pro 4965 ag. Note* this is my mother's router and whatnot. She won't change it the encryption type.
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
I'm new to Ubuntu and am trying to get a Tenda W311u usb wireless working in 10.4:-
root@greenway-desktop:/var/log# lsusb Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 005: ID 148f:3070 Ralink Technology, Corp. Bus 001 Device 004: ID 14cd:8168 Super Top Bus 001 Device 003: ID 04b8:0007 Seiko Epson Corp. Printer Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Got the Windows driver disk and it includes an rt2870.inf driver, not 3070.
I am running ubuntu server x64 as a router. I currently have 2 LAN cards, eth0 and eth1. and I want to add wireless capabilites to the machine.I was wondering if any of you know which card I could use?I want it to be supported in ubuntu server and it must be n-draft, as it is to replace a Edimax n-draft router.
I have installed ubuntu 10.10 and am really happy. I want to sort the wireless conection out now. I have been through this forum for hours today and can't get it working. I have a Broadcom wireless card, which seems to be working fine, but I am not 100% convinced.I have attached the output of some of the commands that I have seen referred to on here.
I am using the wired connection on the same router, so the router connects fine.I click on the network icon and I see the skyNNNN router in the list. I have tried connecting to it and it asks me for my password, which I provide then nothing happens until it asks me again.I have removed the security from the router and I then see the same skyNNNN router without a lock icon. I try to connect and it still fails.I am not using an access list on the router, so there is no issue with the mac address.
I have been using pppoe connect to Internet,now I want my notebook get on line,I bought a wireless router but Ubuntu(64-bite) can't connect to Internet through the wireless router.pppoeconf said that found eth0 and vboxnet0,but search concentrator failed and pppoeconf exited.How can I fix it.
Just installed ubunto 1104 and I cannot connect wirelesly to my router. When I go through the trouble shooting the recommendation is to got to the device drivers page but the link does not take me anywhere. Here is the info from the terminal.
I'm trying to connect to a new Belkin wireless router, but wicd refuses to connect. I've been reading some of the other threads but they haven't made much sense as the hardware is different.
The output from the iwconfig command is as follows:
When I ran lspci it told me I had a RaLink RT2800 802.11n PCI Network Controller. On the box it says it "Supports the most popular systems" and mentions Linux. I'm using a 63 character WPA2 password, which has been copied from a USB key, so I know that is correct.
I have a Belkin Wireless G F5D7230-4. I was attempting to configure a wireless card on another computer on my network when it froze during the reboot phase after making settings adjustments. The wired connection is fine, except on that computer that I was making the adjustments from. It won't connect at all. I plugged a friends netbook into the same wired line and it connected. Also there is no wireless signal on any laptops. Mac, Win Linux, don't matter. I tried all the various methods of resetting to default but still when I try to access the router's config page @ http://192.168.2.1 I get the error Code: The server at 192.168.2.1 is taking too long to respond.
I can connect to my wireless router while logged in as root, but not under my user account. I went into YAST and the user maintenance area and gave myself every permission (Add, Edit, Delete Users or Accounts), but kde network maanger will not allow me to connect to my router.
I have had a router die on me and have bought another (maybe a bad buy!) The new router is Linksys WAG120n. Ethernet is fine. Laptop wireless adapter is Atheros AR5009 802 11a/g/n. I have setup a wireless connection but it is not connecting to it. I have checked the router settings and these seem to be OK! I'll try to give any details required.
Ubuntu 10.10 connects to a DSL modem without any problems - I mean I just plugged it in and it worked - GREAT I bought a wireless router so I could connect my netbook and now my Ubuntu machine which is simply using a cable from the wireless router now DOES NOT connect. I tried a windows machine on the wired connection from the wireless router and it connects without a problem. OF course if I remove the wireless router from the chain, i.e. simply connect directly to the modem it works straight away.
I have an Acer Aspire 1 Netbook - this is running UBUNTU- When I try to connect to my Linksys Router in wireless mode it asks for password - but doesnt accept. I can see the Linksys in network manager plus several other networks in the vicinity. My other wireless devices all connect O.K. to the Linksys, and accept my password.. I can hard wire by ethernet to the netbook. Just wireless is the problem
Firstly, the actual problem I'm having is that when I start my computer (netbook) up in the morning and try to connect to the router (wirelessly) it just... doesn't work. I've used it before, at full signal strength, and it was completely fine. It never disconnects me or anything - but if I shut down my computer, like I do overnight, when I start it up again often it's hardly getting a signal at all (or so it says) and when it tries to connect it makes the connecting animation and occasionally flashes to a circular thing like firefox's loading animation. Eventually it just fails.
I try restarting my computer, but it doesn't seem to help. The last time, I had to wait until the signal looked "full" again, then delete the settings in "edit connections" for that router and only then would it let me log in again, even though I was using the same password from the same computer (even in the same place). That only seems to help when the connection looks "full" though, and even then, not always. Normally I'd try resetting the router, but I can't because it's locked in the next room (I rent a room here and the guy with the key is rarely around) but honestly I don't think the router is causing this, for a few reasons:............
I moved my server and network equipment, and now the wireless works but I cannot get my server online. I host a website, so this is kind of urgent.
I have a wireless router and can access the internet fine on my laptop. My server is wired & connected to the router. It sets up the networking properly.. ifconfig has an ip address, the default gateway is present. But I cannot ping google, or even the router. It says destination host unreachable.
So I go back to the laptop to check the router settings.. sometimes it likes to assign the server the wrong internal ip. But, I can't access the router settings either! The page (192.168.1.1) times out. Same with trying to ping the router. How can the laptop be online if it can't reach the router?
Oddly, ifconfig on my laptop reports an ip address starting with 99.233. It's always given me an internal address starting with 192.168. What's going on here? Is the router not allocating an internal ip? I use wicd to connect, if it's relevant.
We have a windows laptop that can only get a "local connection". Now it does sound like the router is forwarding directly to my laptop, instead of allocating internal ips.
I have a question. I just bought an internet router which also has wireless connection and my notebook also has wireless LAN.I was able to connect the computer to the internet router very easy. But i dont know how to make it work wirelesss under fedora linux 12...i mean how should i setup the connection to the router so i will be able to have a wireless connection?
I connect my internet using pppoe to may DSL modem with bridging mode, and it goes fine until I try to put a wireless router between my PC and the modem. After I configure both modem and the router, I can run my wireless network fine by connecting it from a laptop, but my PC is unable to reach the modem at this configuration.
PC has address 192.168.2.100 Router has address 192.168.2.2 Modem has address 192.168.2.1 all with netmask 255.255.255.0
With bridging configuration in modem and automatic detect configuration in the wireless router, the wireless network run well, except the PC cannot ping the Modem saying that
root@firefly:~# ping 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. From 192.168.2.100 icmp_seq=2 Destination Host Unreachable
Looks like my PC, which has Slackware 13.0, don't know how to reach the modem even they are physically connected.
1. how can I configure the modem, PC, and router so that the PC can reach the router? Do I need to do add route gateway from the PC?
2. How can I configure internet connection from the PC (before I use PPPoE)?
3. How can I configure the modem, PC, and router so that the wireless network is on?
i installed ubuntu 10.04 from internet.but i cant connect to my wireless router linksys wrh54g ver 1.0,but if i using Local area connection its working,however my wireless connection working in my other os win xp.
At work, we (like almost everyone) are still full-on windows. I am currently trying to get away from windows because I am not a fan. my current windows machine (different from my Ubuntu machine) is accessing the wireless network fine, and there are no obvious problems there. Also, my Ubuntu machine can access my wireless network at home, so I know there are no driver issues. I set up the connection for the Ubuntu machine, and it seems to be connecting OK. I can ping internal IPs and by all statuses, the connection to the router is functioning. However, when I attempt to load a web page or ping a domain or external IP, it fails. I tried to ping the IP, thinking if that worked, it's probably the DNS, but pinging both domains or IPs fails. I have looked around at forums and posts, but none of them seem to match my issue (that's probably not true, but I am struggling to see the commonality).
Here are the results of "netstat -r":
Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.45.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default 192.168.45.5 0.0.0.0 UG 0 0 0 wlan0
And here is "ifconfig":
wlan0 Link encao:Ethernet HWaddr 74:f0:6d:XX:XX:XX inet addr:192.168.45.49 Bcast:192.168.45.255 Mask:255.255.255.0 inet6 addr:fe80::76f0:6dff:XXXX:XXXX/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
I am trying to get my Linksys wireless adapter (WUSB11 V2.6) to work under kubuntu /ubuntu.
I am still not able to connect. I believe that I am overlooking or not understanding something.
This is a walk-through of steps I have taken. I can post log files or command outputs as needed.
lsusb shows my adapter, I checked at one point and saw the log file said it needed the firmware from at76c503a.berlios.de so I downloaded the at76_usb-firmware.tar.gz file and copied the at76c503-rmfd.bin file to /lib/firmware and ran chmod 755/ chown root:root as the instructions said.
I then ran rmmod -f at76c50x_usb followed by at76c50x_usb. iwconfig now shows my linksys adapter as wlan1. I use ifconfig to bring the interface up and then set the essid (not hidden) with iwconfig. I then use dhclient to try and get a dhcp address, but no luck.
I have tried setting the wireless mode to managed and setting the ap with the cell address of my wireless router. Still no luck. I continue to the get dhcp no offers report.
I have read that I need to shutdown network-manager if configuring by hand. I did this with service network-manager stop. it doesn't seem to get an address either after this.
Checking the output of messages, kern.log and syslog I get wlan1: link not ready and if I set the ap by hand. I get that it can not associate
Here are some other things that I have noticed and wonder if it is a problem:
lshw shows my wlan1 interface, it shows a loaded driver but gives firmware = N/A (this is after copying the firmware file to /lib/firmware) (log files seem to indicate firmware version)
After setting the ap manually with iwconfig, iwconfig output still shows that the access point is not associated. I am not sure if it is supposed to show the cell address after manually setting it or only if it is connected to the router.
I am running kubuntu 10.10 and I am trying to connect to an open router.
I think something weird is going on. On a fresh installation of 11.04, I seem to be connected to my router just fine, but I can't reach the internet or anywhere else on my network. Anybody see my problem from what I've posted? The computer is only connected via wireless (so I don't know why eth0 would be connected as well). I can't think of what I'm missing...My system seems to be connected to my router on two interfaces. "ip addr" gives:
Code: 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
I've been at this the last 3 hours now or so. I am not a very good with Linux, I am fine with all other areas. I have this laptop, with a Intel Pro 2200BG card. The idea was to install a lxde lightwieght on it and use PCLINUXOS, because its "easy". This computer is for internet browsing and thats it. Under the Network Center -- I can see all networks, including neighbours. When I try to connect to my router via Wireless, I get connection failed over and over.
I then tried doing all the following: Changing the router from WEP to, WPA, WPA2 personal, WPA2 Enterprise Changing the SSID, broadcasting to ON, changing the SSID name I've used various different passwords, and reset the router now about 50 times. I am connecting to my Router (as Ive changed the SSID and noticed it picks up the new name). (Yes I can see the correct MAC addreess). Yes I am on the right channel, all good here.
My Nintendo DS is connecting fine with all the changed settings now. The wireless card worked fine under Windows XP (However I just removed the operating system since I really had no need for it). I've tried every other mode, it works wired. Like I had explained above, I downloaded a what I thought was an easy verison (distro), I was really hoping to get away from the crazy windows life with crazy errors and instability.
I did try enabling display log, and doing it manually by adding a connection, etc. The log tells me about as less would a windows event log: it says Problems occurred during the network connectivity test This can be caused by invalid network config or problems w/ your momde / router Reluanch, etc.
I can connect to the internet fine with wvdial and wvdialconf; heck I am even posting from my PCLinuxOS FM Distro. I want to setup an ethernet connection between two PC's, one running PCLOS 2010.11 FullMonty and the other Knoppix 6.2.0. Knoppix is fine and setting up a connection is simple but with PCLOS I have been having many problems trying to set it up. I tried using the drakconnect tool but it did not work. I tried assigning it a static IP Address but the other PC would still not pick it up and to to it all I keep getting the same error message about problems during the network connectivity test!