Ubuntu Networking :: TP-Link Wireless Adapter (USB) On 11.04 - Not Connecting To Network?
May 19, 2011
i just installed Ubuntu 11.04 64bit on my desktop. i have a TP Link TL-WN321G (Ver 4.0) wireless usb adapter to connect to my wireless network (i used to use it with Windows XP).As expected (i'd read up a bit before installing Ubuntu), the adapter was autodetected - i could see my wireless network listed in the networks list dropdown, and lsusb showed it too.lsusb identifies "Bus 002 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter"But i cannot connect to the network. When i select my network, it keeps trying to connect, but never succeeds in connecting.
i tried going through the forums for possible solutions, but most of them deal with how to get it working when the adapter is not detected, or when networks are not shown. Or they are for older Ubuntu versions.i use the same wireless network on my laptop (Ubuntu 9.04), and it has a WPA & WPA2 Personal security, with a password, which i've configured in the desktop as well.
I'm having some issues getting connected with a TP-Link TL-Wn727N wireless USB adapter. I have no way to connect hard wired with the computer, but I have another working notebook to possibly download files. However, the second notebook is a Mac, so most of the posts I've found are not filling in all of the answers. Also forgot to note, I am using Ubuntu 10.10. I followed along with this and managed to get the card to find the wireless connection. However, the connection would never connect. After entering the security password the wireless icon would do it's thing and then pop up asking to ok the password again. I double, triple checked the password and it is correct. I found elsewhere that I should probably install wicd. This is where I've run into problems with finding the way to get files that I can download on the Mac and then installed on the Ubuntu computer. I managed to find this forum thread and downloaded this file I transferred the file from the Mac to the Ubuntu with a flash drive and tried to install. First the install said that Network Manager needed to be removed, so I removed it. Next it says "Dependency is not satisfiable: python-urwid." I'm not sure how to go about getting this dependency as it is not showing up in the package manager.
I have been running FC8 on this IBM T23 with a D-Link wireless adapter. Using MadWifi this has worked fine with Network Manager disabled. But now I have nuked that installation and replaced it with FC10. Network Manager is nice, and I would like to use it. And it kind-of works. Network Manager recognizes my router and all my neighbor's routers, but I can't connect.
I have "D-Link DWA-125 Wireless 150 USB Adapter". I can use this wireless adapter on my laptop, i can use it on my desktop as well but only when windows is running, im a newbie to fedora, today is my 2nd day and 3rd night, so pretty exited about it. i have installed fedora 13 on a different hard-disk on my desktop. when the computer is booting, there is an orange light on the adapter glowing, it turns off when the computer reaches the fedora loading screen. If i see fedora's Network Configuration window under the hardware's tab i see the "D-Link DWA-125 Wireless 150 USB Adapter" listed along with my lan card. Now if i go towards the clock on the top right to get the wireless connection working, it shows wireless network disconnected. I have tried creating wireless connection manually by inserting the SSID, macadress, BSSID, ,WPA passkey etc, but still doesnt works. when i try connecting using hidden wireless connection, i receive window for inserting keyring password again and again, stating that the login password does not match. but during all this time, i still havent seen the orange light glowing activity on the external usb adapter. If i restart the computer in windows the adapter/wireless connection works. also have checked the Network service, it seems that the service is up and running. i really require some assisstance on this,
i have noticed this, that if i go under network configuration. the first tab over there, inside devices i cant see my D-Link adapter, but if i switch onto the hardware tab it shows my lan card as well as my D-Link adapter. so does it means that the driver is missing? or any service which is disabled, however at this point of time i can get only using wired connection. please assist me. with this issue, im also downloading the 500 complete update as well for fedora, hoping that it may make it work.
I've a damn TP-LINK WG422G UBS Adapter that i love i installed latest compat-wireless driver package and used latest ar9271 firmware after that it was worked properly. There is no problem when surfing the net, the problem is occurring usually download something via torrent sometimes form websites. I'm starting to download and then usb adapter suddenly freeze. If i remove and plug in the usb adapter it is working again.
Have tried methods from every thread I could find for past 10 hrs. Have tried installing rt3070sta etc.Monitored message log; appears that the driver isn't recognized, though the USB port sees that something is plugged in (when I plug in the adapter, and unplug it).All of the threads miss something; I can't get a wireless port listed under ifconfig no matter what I try. Seems that every method leaves out something (I guess because everyone's box is different in some way). Network manager doesn't help much. Downloaded Wicd, which does even less.I guess I could try ndiswrapper, but I'm scared away by the hundreds of pages I see on going that route; I'm almost certain it wouldn't work (1000 possible points of failure).Does anyone have a strategy to recommend?AM64 box, newly installed Edubuntu 10.04, ran update manager.
I have a wireless USB (TP-Link TL-WN620G) adapter on F10( 22.214.171.124-170.2.113.fc10.i686). I have installed the drivers and it is detecting my router. But it keeps asking for network password with repeating a dialogue box although I entered correct password. I have configured the wireless configuration using NetworkManager.
I have tried to install tp link tf3200 network adapter without success . the os is 8.04 hardy loading drivers is new to me. the driver is sundance (i think) and the output from the make command is shown below.
pag@paghomelinux:~$ cd /media/cdrom0/TF-3200/LinuxDriver pag@paghomelinux:/media/cdrom0/TF-3200/LinuxDriver$ sudo make all sudo: unable to resolve host paghomelinux
For several months I was using EDUP adapter with both my laptop that operated on Ubuntu 9.04 exclusively and a desktop that could also boot with XP. Soon after 9.10 was released I updated my laptop and was able to use the adapter to connect to the Net.Recently, I also updated the desktop but also made it exclusively a Linux machine. Unfortunately, I have been unable to get the wireless adapter to work again on the desktop.The OS recognizes the device as wlan0, and lsusb shows:Bus 003 Device 005: 0cde:0008 Z-Com Sitecom Wireless Network Adapter 100G+ WL -125The network manager recognises the availability of the wireless network and attempts to connect. After trying for a while it comes up with a dialog box "Wireless Network Authentication Required" and in response I enter the WPA password but with no success.The behaviour would indicate that I am entering the wrong password but I am not.I have checked it several times and compared with the password that works with the laptop.
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly. 2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page. 3) From terminal I typed "cd Desktop" to change the directory to the desktop. 4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb" 5) This installed Windows Wireless Drivers gui successfully and I can access it. 6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed. 7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder. 9) Upon mousing over the network Icon naturally my hardware is still not present. 10) From what I gather after the system finds the hardware I am to write into the terminal
I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
I have an HP Pavilion dv5 1002nr laptop running Vista. I decided to install Ubuntu using the windows installer, which did install well, but I decided that it wasn't for me, and uninstalled it. Now, my wireless adapter which is a Atheros AR5007 802.11b/g can see the network, find networks by itself, and is supposedly installed correctly according to Vista, cannot connect to any networks at all despite being able to see them and acquire a signal strength. Up until installing Ubuntu I have never had an issue like this. Other devices have no trouble connecting to this network, and I am currently using a Netgear wireless usb dongle to connect to the very network that my Atheros can not connect to.
I just got a new AZiO AWU212N 802.11n wireless usb adapter (linked below). One of the product reviews said that it works with Ubuntu if you upgrade to the .34 kernel so I thought it would be a good buy. I updated my kernel and Ubuntu detects that there is a wireless adapter, but doesn't detect any networks. My old wireless-g adapter can connect just fine, so I don't know what the problem is.
Could anybody confirm that the D-LINK DWA-556 wireless N PCI-E network card works with Lucid Lynx 64 bit? Im looking for a reliable wireless network card that if possible works out of the box on Lucid 64 bit, so far my search has lead me to the above card, If anyone has hands on experience of this card on lucid 64
I would share my long awaited success with connecting my ubuntu laptop up to my universities (University of Western Sydney) wireless network. The rumors appeared true and they have finally implemented 802.11x authentication instead of that horrible java app netdirect. I am sure you've been cursing at its erratic stability. There is no linux documentation for airUWS-Lite nor anything more imformative than there windows/mac point and click steps found at [URL]. However with a few simple clicks you can have stable working connection.
When connecting make sure you have theses settings. Security: WPA & WPA2 Enterprise Authentication: Protected EAP (PEAP) #This is the settings that does not present itself correctly Anonymous Identity: leave blank PEAP Version: Automatic Inner Authentication: MSCHAPv2 Username: <YOUR 8 DIGIT STUDENT NUMBER> Password: your regular password
I have a fairly new install of 10.04 on a Dell laptop (about a week). Everything was running well, connecting wirelessly to the interneet through my home router (WPA/WPA2). Today, for some reason, I lost my connection to the internet. The network manager tells me I'm connected to my router, but all the lines on the wifi indicator are gray and there is no internet access. I reinstalled the 2 sets of packets for my BCN4312 (bcmwl-kernel-source and b43-fwcutter ), but no change.
May I put a USB 54Mbps Wireless Network Card Adapter into Ubuntu Studio- 64 bit, does the 64 bit Ubuntu Studio (9.10) support this usb wireless network card adapter? how to let it work in Ubuntu Studio 9.10
I recently upgraded from Ubuntu 9.10 to 10.04 (both 64-bit) and my USB WiFi adapter which previously worked fine stopped working. The adapter is a Hama USB stick based on the Ralink rt73 chipset. I've tried using the Ralink drivers that come with 10.04 (both rt2800usb and rt73usb) but neither work. When I use rt2800usb, the adapter is recognized as interface wlan0, however I can't see any wireless networks. When I use rt73usb (and blacklist rt2800usb to avoid conflicts) I no longer have a wlan0 interface and there is no wireless adapter shown in the network manager. I've pasted in the results of lsmod, lsusb, and ifconfig -a (with MAC addresses removed) below.
I have a Toshiba MX35 laptop it's a little old but does the job. I'm have a problem getting the wireless to work. I can boot a live CD either Ubuntu 10.10 or Fedora 14 and they will see the wireless card. The card is Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01).
I have Ubuntu 9.10 installed and that is the OS that is having the problem seeing the wireless. The computer will not handle Ubuntu 10.10 (at least it won't handle the desktop effects under Ubuntu 10.10) but handles them just fine under 9.10 and that's why I have 9.10 installed. I really need the Wifi to work because I'm going to travel in a few days.
Using openSuSE 11.4 D-Link DWL-520+ won't connect to my router. The computer recognises the wireless card is there and working but I can't get it to connect to the router. Not sure how to get it to connect.