Ubuntu Networking :: How To Bridge A Wlan Card In Managed Mode
Feb 3, 2011
I have 2 wlan cards. wlan0 and wlan1. wlan0 is in AP mode(Master mode) using hostap. wlan1 is connected to another wireless network and is in Managed mode. Now I want to make a bridge between wlan0 and wlan1. I do it like that:
ifconfig wlan0 0.0.0.0
ifconfig wlan1 0.0.0.0
brctl addbr mybridge
brctl addif mybridge wlan1
can't add wlan1 to bridge mybridge: Operation not supported
It doesnt work, because wlan1 is in managed mode. But Windows 7 can bridge 2 Wlan cards when one is AP and another one is STA. How to do it in Linux?
View 4 Replies
ADVERTISEMENT
May 25, 2011
Can you "split" a network interface in Ubuntu, similar to how airmon-ng lets you use your wireless card in managed and monitor mode, by making another interface out of the same hardware? I know it'd be slower, but I'd still like to do it.
View 4 Replies
View Related
Jan 11, 2011
I'm trying to get a wireless PC (PCMCIA?) card working under 10.04 desktop. It does not seem to be recognized by nm-applet and I cannot see any particular reason why. I have disabled the built in wireless (Intel 2200) in both BIOS and by blacklisting the appropriate module so there should be no interference from that. The card is a Linksys WPC300N V1. It has Power and Link/Act LEDs both of which remain dark.
Here's the information I have collected regarding the card:
lshw:
Code:
hbarta@willow:~$ sudo lshw -c network
*-network
description: Ethernet interface
product: 82540EP Gigabit Ethernet Controller (Mobile)
[Code]....
I saw a comment about 'You need to have "managed=true" for NetworkManager to bring the interfaces up. in '/etc/NetworkManager/nm-system-settings.conf and did so but I see no change.
I understand that modules must be compiled to support network-manager but I would expect that to be the case with modules that ship with 10.04. I don't see any obvious indications for why this is not coming up with network-manager. Is there something I;m overlooking or something else I need to do?
View 5 Replies
View Related
Nov 7, 2010
I have OpenVPN running on my Ubuntu Server just fine. I can connect over the Internet and access all my resources on the LAN via bridged mode perfectly. My server only has one LAN card and sits behind my router, which means it has a private IP address of 10.1.1.2....Which brings me to my question. I want to open up access to my friends via OpenVPN, but I don't want them to be able to access other machines on my LAN (e.g. 10.1.1.20). However, I do want them to be able to talk to each other and pass broadcasts (old LAN games), as well as my laptop (let's say 10.1.1.7).I've tried using iptables to block traffic to the LAN (such as .20), to no avail. I've been reading up and it seems as though iptables won't even filter the traffic, as it's passed at a lower layer. Is this true? If so, what do you recommend I do in order to prevent my buddies from accessing the rest of my LAN while siumultaneously allowing broadcasts pass for some very old Windows LAN games (we're talking Windows 9.
View 2 Replies
View Related
Apr 7, 2010
I have installed CentOs 5.4 for Snort sensor , on the location where i intend to place the Snort sensor to listen for internal firewall leg (LAN) the switch doesn't support port mirror so i would like to create with 2 nic's bridge and pass trough the firewall internal leg my question how do i set such configuration.
View 2 Replies
View Related
Jun 27, 2011
How would I configure my box to connect to a modem in bridge mode?
I have a server at home that im migrating over to be the default-gateway/router. I have everything else setup (dns,dhcp etc) now just need the ppoe part, or so i beleive?
I have two interfaces. eth0 (lan) and eth1 ready to connect to the modem.
The modem is in bridge mode ready to go.
What is my next step? Are there any good guides, I didn't find any.
View 5 Replies
View Related
Nov 3, 2010
I use my T61 both wireless and in the dock, where I switch to the wired connection. After the latest round of updates, I seem to have lost the ability to switch to the wired network. When I turn the laptop on, I see it connect to the wireless network, but when I left click on the tray icon under Wired Network is says Device not managed. I have not made any changes to anything in the last couple weeks, besides some updates. How do I go about getting the wired network back in there?I tried to add eth0 back into System - Preferences - Network Connections, but whenever I try and add eth0, but it still says Device not managed.
View 2 Replies
View Related
Mar 3, 2010
setup linux in bridg mode for my windows server ?
my both linux and windows has 2 network cards each.
basicaly it is vLan cards, each server has 2 network cards. one to main switch and one to local IP.
data will be going like below:
internet ----------------> eth0 --> linux --> eth1 ----------------> Windows.
i have vLans on both servers. And i need cross connection setup. And use linux in bridg mode / cross connection .
actualy i want to use Iptable rules to filter bad packets and forward good packets to windows. i have scripts how to forward packets to windows. but the problem is i dont know how to setup both servers in this topology. and how to make linux as bridge.
All it should be in transparent mode. Not in NAT mode.
View 14 Replies
View Related
May 23, 2010
specific Ubuntu supported WLAN PCI-cards? This link shows a list of supported PCI-cards, but which is best: [URL] And the installation needs to be easy! I�ve tried installing these PCI-cards in my computer, useing Linux drivers, NdisWrapper, etc. Unforutately without any success:
- DWL-G510, Ralink Chipset, Ralink RT2561/RT61
- Realtek Semiconductor, RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller
View 1 Replies
View Related
Aug 10, 2010
I have bought a new laptop with win7 on it , I delete win7 and install ubuntu64 everything is ok but my wireless card won't work ( it is recognized) and even I can connect to INTERNET but nothing is download or upload so I have bought another usb wireless card but now when I connect this new card to my laptop it still tries to use the old one and so I could not connect to internet
View 4 Replies
View Related
Dec 25, 2010
I'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.
Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.
View 1 Replies
View Related
Jun 25, 2010
Am having intermittent connectivity issues with my stock Atheros AR5212 on my Thinkpad X61 using Ubuntu 10.04. Am wondering if there is a known to be good b/g min-PCIe card that I can replace my AR5212 with that would be more solid in Ubuntu?
View 2 Replies
View Related
Mar 5, 2009
I have been using FC10, it works well with wlan for sometime and goes inactive after some time and hence network goes unavailable. Even after few attempts to reconnect doesn't help. Rebooting helps in bringing it back temporarily.
View 7 Replies
View Related
May 17, 2011
I upgraded Ubuntu to 11.04 I can NO longer connect wirelessly using my BCM4312 WLAN Card. It connected with no problems before dist upgrade using Ubuntu 10.04. Im really not sure why I cannot connect. I cannot even see my router in edit wireless connections settings. I can however see my neighbours routers who are using WPA2 encryption. But I cannot see my router.
I have uninstalled and reinstalled The Broadcom STA proprietry wireless driver several times using Additional drivers. This did not fix my issue.
I am connected by ethernet at the moment so I do have internet connection.
View 4 Replies
View Related
Nov 20, 2010
I'm having trouble setting up new Alix URL... system with a wireless card. I got the card from an old working Buffalo AirStation router. The card is a WLI-MPCI-G54 and is using Broadcom BCM4306 chip. I've installed Debian on the system.My goal is to make a wireless access point by using hostapd authentication service. I thought it might be a good idea to verify that the wlan-card is working properly first, but it can't seem to detect my local wlan.
View 1 Replies
View Related
Jul 28, 2010
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
View 3 Replies
View Related
Sep 9, 2010
I'm using Ubuntu 9.10 on a Lenovo ThinkPad T61 using an Intel PRO/Wireless 3945ABG. My laptop's ability to connect to a wireless network stopped last night, and I'm not sure why. It's definitely something on my end, as my roommate can connect to the internet on a Windows box. I can wire in without a problem, but that's a pain and my Ethernet cable got lost in the shuffle when I moved back to school. I've been able to get into this network before and nothing about it has changed. I've been able to hibernate and restart and such and nothing has ever needed to be reset.
The router's a D-Link WBR-2310. Wicd and Network Manager see the network (I'm back to using wicd) , but wicd appears to get stuck at "Obtaining IP address..." and says "Unable to connect: Cannot obtain IP address". I know my password is correct (I set up the router and I'm the CS undergrad in the apartment so I manage it), lspci sees the wireless card, ifconfig and iwconfig return information about the interface, dmesg|grep wlan0 doesn't seem to have anything terribly out of the ordinary, but here's that output:
Code:
allyanncah@taliesin:~% dmesg | grep wlan0
[ 23.514202] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.609016] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 38.756143] wlan0: direct probe to AP 00:24:01:cb:4e:7e (try 1)
[ 38.758791] wlan0: direct probe responded
[ 38.758796] wlan0: authenticate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.760587] wlan0: authenticated
[ 38.760609] wlan0: associate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.763318] wlan0: RX AssocResp from 00:24:01:cb:4e:7e (capab=0x431 status=0 aid=1)
[ 38.763322] wlan0: associated
[ 38.765502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready .....
I've tried:
- reinstalling wicd
- uninstalling wicd and installing network-manager
- restarting
- shutting down and booting back up
- restarting the router
- sudo /etc/init.d/networking restart
- taking the interface down and back up with ifconfig
I haven't changed anything recently in regards to my wireless card, and all the fixes I've tried are things I've done before without an issue. The only thing I'm wondering about is if doing a hard reset might have broken something (I know this is a cardinal sin, but there's a whole 'nother problem I haven't been able to fix with the OS hanging every once in a while over a VPN daemon when it tries to shut down or restart -- I've left it for hours to see if it actually gets anywhere and no luck, won't do a soft reset). I'm nervous about reinstalling the driver just because I've never had to do it and drivers are a finicky business. I imagine there's a config error somewhere?
View 2 Replies
View Related
Sep 8, 2010
I have a Dell Inspiron 1525 laptop using Dell Wireless 1395 WLAN Mini-card (This is what Windows Vista says I have). I have installed Ubuntu as dual boot with existing Windows Vista. Wireless is not working in Ubuntu but working flawlessly in Windows.
Here is the output using CODE: lspci.
hai@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
02:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
02:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12)
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
hai@ubuntu:~$
View 2 Replies
View Related
Jul 5, 2010
I've just got a TP-Link wn-851n PCI WLAN card, and the problem is that ubuntu can search for the network, but I can't join into the network after typing the password. I'm sure that it is correct as m Windows notebook is also using that network.
Taking a look in dmesg, and it start to loop this message after I joined the network.
Quote:
View 1 Replies
View Related
Jul 9, 2010
I want to connect my modem straight to my fedora 13 box, using it as a firewall, and I want to use my wireless card to set up an ad-hoc to give internet to the windows computers in my house. My router has been messing up and I am trying to create a quick fix until I can solve the problem.
My eth0 has internet connectivity but when I use the brctl command to try to create a bridge it doesn't let me add my wireless card, wlan0, and also I lose internet while my eth0 is in a bridge. I am fairly new to Linux.
View 2 Replies
View Related
Feb 18, 2010
I have a Dell Latitude D800 with a Dell Wireless 1350 (802.11b/g) WLAN miniPCI Card. I need to install wireless on this laptop but I see no wireless card when I know I have the above wireless card. Here are some commands that I ran that I might prove useful:
[Code]....
View 6 Replies
View Related
Oct 26, 2010
Inspiron 1525 - Wireless 1395 WLAN Mini-Card I passed two days browsing the net looking for a solution to my problem but no way.. Im running ubuntu 10.10 in my inspiron via VirtualBox and my wireless card is not detected by ubuntu.. I installed the bcmwl6.inf driver with the wrapper and it show me in wireless window that the hardware is not present.. So checked that in the terminal by typing :
Code:
lshw -C network
*-network
description: Ethernet interface
product: 82540EM Gigabit Ethernet Controller
[Code].
View 9 Replies
View Related
Dec 8, 2008
I want to set up a bridge using bridge-utils within /etc/network/interfaces like is shown here in this guide: [URL] The problem is that, at the same time, I want eth0 to have a specific static IP address. Right now I have a configuration for eth0. This guide tells me that I should not configure eth0 outside of the br0 configuration.
View 3 Replies
View Related
Mar 30, 2009
very much like everybody i am also waiting for centos 5.3, because 5.2 could not sit on my notebook due to obvious driver issues. would anybody tell if centos 5.3 support my x3100 graphics card and bcm 4311 wlan card?
View 5 Replies
View Related
Nov 15, 2009
I have a desktop that has a d-link DWL-520 wireless card, which was working under Windoze. Today I installed Centos 5.4 on the system , which went cleanly. I then used Network Configuration to set up the wireless card. I specified to use DHCP, set the SSID and authentication password. When I tried to activate the card I get these error messages
Error for wireless request "Set Mode" (8B06): SET failed on device wlan0 ; Operation not supported. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Error for wireless request "Set Encode" (8B2A): SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0.
The hardware manager seems to have correctly identified the card and chipset, (Intersil Prism 2.5) and installed driver hostap_pci which came with the distro. This web site seems to suggest that this is the correct driver: [URL] searching forums I've found a few references to these errors, but they were from several years ago, and for different distros and cards. I did find a reference to using Network Manager to configure the card instead of Network Configuration. I started the NM service and configured a connection using it instead, but still no luck.
[Code]....
View 15 Replies
View Related
Mar 30, 2010
I have a dell 1521 and I can't get internet working, I thing the driver is no working with ubuntu 9.10
View 1 Replies
View Related
Sep 24, 2010
I wonder what is your opinion about the best method for using an ADSL modem. Router or bridge? I did read some articles that say "that the bridge mode gives you more stability and has higher speed". Is that true?
Furthermore, you suggest any alternative to "pppoeconf"? I've been getting this errors ( in the plog), related to "PAD packet loss" and also errors in "PPPOE Discovery", even when I am connected. When this things starts to show up on the log, my connection "pauses" for some seconds. I do not feel very safe with this program.
View 3 Replies
View Related
Dec 20, 2008
I've successfully install kvm with private network (nat) up running. I want to switch the kvm network using bridge mode (or host-interface), but do not success. env: nic iwl4965/ kernel 2.6.27.8/ debian etch upgrade to lenny/ kvm 0.9.1/ hardware hp 6910p The doc I follow up is at [URL] The way how i set it up is to modify /etc/network/interfaces by adding following section to enable br0
Code:
allow-hotplug br0
iface br0 inet dhcp
bridge_ports wlan0
bridge_fd 9
[code]....
However, the problem is the guest os, which starts with -hda k1.img, can not access to the internet. Is there any step I miss? or it is because wireless does not support bridge (I've heard doc says that wireless does not support wireless bridge)?
View 4 Replies
View Related
May 12, 2011
I'm trying to setup openVPN on debian, well this worked. But every client will get the same ip (172.17.0.6 - local it is). how to set my server in bridge mode. I've read about: server-bridge LOCALIP 255.255.0.0 172.17.1.20 172.17.1.100
BUT, my server has no ipv4 address, but only ipv6: 2001:41d0:2:b2d6::542a:74a so I am not sure how I can do this.
View 1 Replies
View Related
Sep 3, 2010
I configured squid in transperant proxy and it's working fine.Now i tried it in bridge mode for that i did setup for bridge mode and it's working fine.But i can not get any http request in squid access log.i can see traffic from my bridge. tcpdump -i br0
configure bridge:
ifconfig eth0 0.0.0.0
ifconfig eth1 0.0.0.0
brctl addbr br0
brctl addif br0 eth0
brctl addif br0 eth1
[Code]...
View 1 Replies
View Related
