Ubuntu Networking :: 10.04 Wireless Connected But No Internet Access
Aug 26, 2011
I have installed ubuntu 10.04 and STA wireless driver. I am using a wimax modem, the wireless is connected (have IP addresses) but I do not have access to the internet.I also have installed a windows XP as a guest OS (ubuntu is the host) on vmware. By using a bridged network connection, I am able to access internet. So I guess the problem is related to the ubuntu wireless driver.
View 9 Replies
ADVERTISEMENT
Sep 17, 2009
if i'm connected to my wireless network it only gives me internet acces for a few minutes. The connection with my network stays but i have to close it back of and reconnect before i get back online.
View 1 Replies
View Related
Mar 4, 2010
im using mandrake linux 2010.0 , and i connected my router cable (dlink) to the computer, and it detects without needing configuration to the 'eth0' and it shows me the ip the dns and gateway, everything ok, but then i go in firefox it says that i couldent connect because theres no internet connection,ive looked at the proxys the firewall, tried to uninstal the eth0, the ppp0 and install then again and still the same,does any one have an idea of what could be?
View 9 Replies
View Related
Jan 12, 2010
When I connect my PDA (AT&T Tilt with Windows Mobile 6.1) to my desktop via USB (my desktop is connected to Internet via LAN), I can't access Internet from my PDA. How can I share Internet from my desktop with my mobile phone?
p.s. I can only find how to access Internet on a desktop using a mobile phone as a modem.
View 2 Replies
View Related
Sep 5, 2010
I've been using my upstairs computer with no problems recently up until this evening, when I rebooted it did an automatic scan of my disks, so I left it to it's thing and when I came back ubuntu had successfully booted, and had seemingly successfully connected to my wireless network as usual.
I've been through the wireless troubleshooting guide, paying special attention to sections 4 and 6 but to no avail, while I'm apparently connected, and have been assigned an IP by my router I'm unable to access anything outside my computer, including the router itself. This happened before, however I solved it by reinstalling ubuntu, and I'd rather not do that again!
output of ifconfig
eth0 Link encap:Ethernet HWaddr 00:1c:25:38:8e:de
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code]....
View 6 Replies
View Related
Sep 20, 2010
I am facing very strange problem with my Dell with WiFi card (04:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100) It seems I am connected to the WiFi but can not access internet I have to disable networking and re-enable it to access internet.
Network configuration
Quote:
-network
description: Wireless interface
product: Wireless WiFi Link 5100
vendor: Intel Corporation
[code]....
View 4 Replies
View Related
Mar 24, 2010
Background infoMy laptop (MySN MG6.c) is dual-booted with Windows 7 and Ubuntu 9.10, and connected to the internet through a router (Digitus DN-11004-O), which is set-up to use DHCP. The internet connection works fine under Windows, and my previous laptop, which also ran Ubuntu 9.10, had no problems connecting to the internet through that router.The network adapter is an Atheros AR8131 PCI-E (also detected as Attansic under Ubuntu)stem infoResults from running various diagnostics (I have removed the output that relate to the wireless connection, as I don't use it):
Code:
$ uname -a
Linux valyria 2.6.31-14-generic-pae #48-Ubuntu SMP Fri Oct 16 15:22:42 UTC 2009 i686
[code]...
View 2 Replies
View Related
Jun 5, 2011
I am using ubuntu (11.04) here, when i connect Bsnl broadband link(wired connection). Internet is connect automatically But unable to instal, upgrad and access Internet pages ..
View 1 Replies
View Related
Nov 7, 2010
Im using a laptop with a wireless card inside it is a Realtek RTL8187B network adaptor. I go to wireless connections in the toolbar at the top of the screen and click on my internet modem and it says its connected. So I go to firefox and it brings up google. I try and do a search and it says something and at the bottom of the page it displays a button that says "Try Again". Im booting ubuntu from the cd drive so its not installed on my computer what should i be trying?
View 2 Replies
View Related
Jan 11, 2011
I have an old GX 159 Dell Desktop I tried to install Ubuntu 10.10 on it and it worked like charm the problem is when I connect my Alfa 1 wireless adapter and connect to the network it won't let me connect to the internet. Well I have been succeeded to connect to the weather center, but I can't update or open the Internet even if I have been able to open Hotmail.com after 2 minutes it won't open anything after that
Note: I didn't install the driver for adapter and I don't know how to do it because I tried before and I failed adding I used it on more than one distro. By the way it works perfect on Windows?
View 1 Replies
View Related
Nov 17, 2010
I have internet from KabelBW (cable modem which doesnt require any username,password,dns,mac...) they gave me a cisco modem, I connected it with my asus router and it has been working fine since today! when I woke up I turned on my lap top and loged in skype, but I couldnt open google, then I tried yahoo..nothing! I havent made and changes yesterday! I dont know what is wrong! I am new to ubuntu and I dont know what to do! when I connect directly to modem I have internet it works good, but when I connect through my (LAN or Wireless) router I cant view web pages. I have tried to google for the answer but all the answers are for windows OS versions! I tried to restart lap top, and the router 100 times but nothing!
View 9 Replies
View Related
Apr 26, 2011
can't access internet. The up and down icon appears by the network connection (upper right hand corner). When I review connection properties, I see that the computer has a valid address, subnet, gatway, dns, etc... But it still can't connect to the internet. I can't ping external addresses either. But I can access internal addresses (local router).
View 2 Replies
View Related
Nov 9, 2010
I upgraded to 10.10 the day it came out, and haven't had any problems with internet stuff. My wireless card works without any proprietary drivers. Last night, the computer stopped connecting to the internet. I am still connected to my wifi network, but I can't do anything online. I had assumed that my internet connection was just down in general, and tried resetting the computer, shutting down the computer and then turning it on again, and rebooting the modem, but then my Xbox connected, and my laptop running 10.04 connected, so I'm confused as to what is going in. Any ideas?
View 2 Replies
View Related
Dec 27, 2010
I am running Ubuntu 10.10 on a Dell Dimension 4700 desktop computer. I just upgraded to 10.10 from the previous version after getting my D-Link wireless adapter back after loaning it out. My internet now won't stay connected. I can connect when I firstrn on the computer, with after 2-5 minutes it drops the connection and gives me the "Wireless Network Authentication Required" prompt. It won't connect again without unplugging the adapter and plugging it back in.I borrowed a Belkin wirelss adapter to try it, and it does the exact same thing. PLEASE can someone help me, I really need the internet up on the computer(Also, when I first got the adapter-- while running the old version of Ubuntu-- it would not recognize or connect at all and I spent 4 hours messing with drivers and settings to get it to work, which it did flawlessly. Until I upgraded.)
View 3 Replies
View Related
Feb 22, 2011
I've had ubuntu installed for a bit now and I want to start using it as my main OS, but the wireless internet will not stay connected. It will connect at first and if I'm lucky it will stay connected for around 15 - 20 minutes. I have a toshiba laptop with an AtherosAR5007EG internal network card.
View 2 Replies
View Related
Sep 3, 2011
I installed Fedora 15 today and after a few very long hours finally got the broadcom driver to work and my laptop is now connected to my router. Yay! But now when I try going to a website in firefox it says server not found. I can ping anything inside my network but when I try to ping outside the network, for example google, it says ping: unknown host google.com. So I thought it might be a DNS problem but the network settings point to the router for DNS so I'm not sure what else could be wrong. All of the other settings look correct.
View 2 Replies
View Related
Dec 11, 2010
I have Ubuntu running from my flash drive. My wireless connection shows good connection to my router and other routers I have tried; however, when I open Firefox or chrome there is no internet connection.
View 1 Replies
View Related
Mar 1, 2011
This morning my Ubuntu 10.10 Meerkat desktop suddenly lost internet connection, but stayed connected to my netgear router. After the usual "tried turning it off and on again" methods didn't work, I booted into my Win Vista partition to find that connected no problem. I have another Ubuntu netbook and a Windows 7 laptop in the house as well as an Android. These all connect fine. It appears to be just the desktop Ubuntu.
I can ping my router 192.168.0.1 and log into it's UI via browser. I can also ssh to the box. My router does not do any filtering or blocking. I've tried disabling the firewall and changing the nameservers in /etc/network/interfaces and dhclient.conf as well as the network manager. The network card is a Belkin 54g but I can't remember the exact model no. it was bought years ago.
Code:
$ping www.google.com
PING www.l.google.com (74.125.230.115) 56(84) bytes of data.
^C
--- www.l.google.com ping statistics ---
30 packets transmitted, 0 received, 100% packet loss, time 29004ms
Code:
$traceroute 74.125.45.100
traceroute to 74.125.45.100 (74.125.45.100), 30 hops max, 60 byte packets
1 * * *
...continues to...
30 * * *
When I do a restart of the networking service it spits out the error:
Code:
Ignoring unknown interface wlan0=wlan0
However, as I said the wireless itself works.
/etc/network/interfaces:
Code:
auto lo
iface lo inet loopback
iwconfig:
Code:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"haters gonna hate" .....
View 1 Replies
View Related
Aug 2, 2011
I think something weird is going on. On a fresh installation of 11.04, I seem to be connected to my router just fine, but I can't reach the internet or anywhere else on my network. Anybody see my problem from what I've posted? The computer is only connected via wireless (so I don't know why eth0 would be connected as well). I can't think of what I'm missing...My system seems to be connected to my router on two interfaces. "ip addr" gives:
Code:
1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
[code]....
View 9 Replies
View Related
Mar 21, 2010
Is there away to view wireless access points without being connected. I am having trouble getting connected to my wireless DSL modem. I have no problems connecting with Windows Vista. Just can not get Ubuntu 9.10 to connect. iwconfig says no associated with access point. I can connect with ethernet cable.
View 3 Replies
View Related
Sep 7, 2011
I just installed a dualboot win7/F15 on my laptop (dell XPS 15) and everything seems to be working fine except that when I connect to my network it is connected and the network is accessible (I can visit my gateway/ router) but when I try to visit a website it simply never ends loading it.Internet is working on win7 so it isn't my network's fault.Now I found somewhere that updating could help but since I dont have internet I can't update
View 3 Replies
View Related
Sep 14, 2010
So I installed 10.4 on a new Toshiba Satellite L645DWhen I connect to my wireless at home, the Network Manager shows that I am connected but I can't reach any websites via ping or firefox. I also can't ping my router. I also don't have wired access working at all.iwconfig shows connected to correct ESSIDI can ping localhostcan't ping google:
Code:
ping: unknown host www.google.com
can't ping my router (192.168.2.1):
[code]....
View 8 Replies
View Related
Dec 7, 2009
I was trying out the fedora live cd but I couldn't get my Internet to work. When I open firefox it always said server not kind no matter what I searched or put into the address bar:
I tried many different things but none o them worked
I am able to ping m router an I'm able to login to my routers page
I am also able to login to my modems page and it says connected to the Internet
I tried restarting the modem and the router but I still got the same problem
I also tried disabling the firewall but still had the same problem
I tried a command and I was able to receive packets from google.com, but It never went through in firefox
I also tried out a torrent (I had it saved on a USB) and it worked it was downloading fine
I am able to ping googles web page but I am not able to search anything.
In firefox preferences and in network proxy I tried many different proxy settings bit none o them worked I always get the message server not found. All this was done while connected directly with Ethernet cable modem and router but untried wireless and it didn't work either on the top right corner of the screen the network icon says auto eth0 active. I'm using fedora 12 livecd.
View 2 Replies
View Related
Oct 15, 2010
I can connect to my school's wireless network using the standard network manager, but often (not always) it repeatedly disconnects and reconnects every few minutes. Occasionally it also prompts me for the security information again (even after it previously connected successfully).
By running iwconfig when it's on the fritz, I can see that it's often switching access points for the network - which is what I think is causing the problem. It disconnects and reconnects even when the signal strength for the current AP is fine, and it will often switch to an AP with a weaker signal strength.
$sudo lshw -C network
Code:
description: Wireless interface
product: Realtek Semiconductor Co., Ltd.
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:05:00.0
logical name: wlan0
[Code]...
View 4 Replies
View Related
May 15, 2011
I have a wireless network (192.168.1.0) that's bridged to the Internet and a wired one (192.168.0.0) that's only local. When I am connected to both networks, Natty wants to route my Internet traffic through the wired, local-only one.
Can I make it automatically "just work", so that the right network is chosen for Internet traffic? Otherwise, what's the workaround?
View 2 Replies
View Related
Sep 17, 2010
I cant connect to the internet with my wireless( or my lan for that matter, but i mainly want to use my wireless). I am going to follow the ticket provided by one of the sticky threads [URL]
1.Machine Brand and Model
Actually i am using a computer i built myself using following components
AMD Phenom II x4 965 CPU
ASRock 890FX Mobo
[Code]....
View 4 Replies
View Related
Mar 22, 2011
Heres the set up I have: one eeepc running ubuntu netbook. with a usb wifi dongle, this is connected to a parabolic antenna i made out of pizza boxes and tin foil. One fujitsu laptop running ubuntu 10.10. the eee connects to the internet via the dongle. then the laptop connects to the eee. I set this up by using network manager. I created a new wirless connection and called it "UbuntuAdhoc". The on-board card connected to this without issue and the laptop was able to connect to the new wireless broadcast by the eees on-board card.
This worked perfectly untill I rebooted the eee. Now the eee is unable to conect to the internet if the on-board caard is conected to "ubuntuadhoc". also the dongle now wants to conect to "ubuntuadhock" too.
View 1 Replies
View Related
Feb 10, 2010
Running Ubuntu 9.10 Ive just got my wireless connection working after first having got the wired eth0 connection working.
With the wired connection I could SSH into my server through my firewall/router (via a forward). I can run up VNC, from there firefox, browse the web - all is well.
I have now setup the wireless connection, using a static IP, and I can likewise SSH into my server. I can run up VNC. I can ping my router. I can log onto it via VNC. I can browse to my router. But I cant browse the internet.
But I cant ping google.com. The reason is there is no host lookup service. Nslookup eventually says no servers could be reached.
So specifically, if I ping www.google.com Im told "unknown host". If I do an NSlookup on it I get timeout, no servers could be reached. However if I ping 66.102.11.104 I get responses.
I see no relevant entries in my firewall log.
Unfortunately I cant traceroute because the package isnt found - and of course I cant install it because I have no internet !
Strangely (to me at least !) if I then tunnel through SSH and browse the web, I have no problems. It works ? I know I am browsing through my SSH tunnel because whatsmyip gives the IP of my router at home, not where Ive SSHd in from. I can surf just fine.
why I cant do host lookups any more (and this did work with my wired connection, but whether its related to my change to wireless, or static IPs or both I cant be sure - it certainly appeared to happen at the same time). And, more to the point, what I need to look for/do to rectify it ?
As a bonus Id be interested in why I can SSH and browse via tunnelling but not direct from my server (via VNC). Just for interests sake !
if config reports :
wlan0 Link encap:Ethernet HWaddr 00:90:4b:27:ae:17
inet addr:192.168.1.69 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::290:4bff:fe27:ae17/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]....
View 1 Replies
View Related
Apr 18, 2010
I have a dual-boot desktop with Windows 7 and Ubuntu.Problem: Linux does not recognize my D-Link DWA-131 Wireless N USB Adapter. So, I can't access my wireless router or the internet.D-Link has a Linux driver for the DWA-131 posted on their website URL...that includes a readme file with long, strange, convoluted instructions on how to install the driver.
View 9 Replies
View Related
Dec 6, 2010
I had been happily using a wireless connection for about two weeks. The connection then went down for a few days. Since it came back up, I can connect to the network, but cannot access the internet. Other users of the network can both connect to the network, and access the internet, though people have experienced the same problem as me the last time the network went down (they could connect to the network but not access the internet). I have tried deleting and re-starting the connection, to no avail. I have looked around the forums, but haven't found anything that can help: do any of you have any suggestions? I am malarial and at the end of tether.It is not a problem with Ipv6, which is set to ignore, as it was in the past when the connection workedI am running Ubuntu 10.10 on an X61 Thinkpad. Below is the output of iwconfig, route -n, lspci, and what happens when I ping other network
Iwconfig:
eth0 Link encap:Ethernet HWaddr 00:1d:72:9e:09:8f
UP BROADCAST MULTICAST MTU:1500 Metric:1
[code]....
View 2 Replies
View Related