Should I be able to see eth0 in the Network Connections control program that ships with Kubuntu?Its not there. See screen-shot.eth0 definitely exists and I can access the Internet no probs but it doesn't show in the above.
I'm running Fedora 12. I've been using Amahi for a trial but this blew up. Last attempt to use it flagged up a problem with Ruby on Rails release version incompatabilies. I've removed Amahi using the software toolk. I now have no internet access and no ETH0 in network manager. How do I get my ethernet back?
i'm trying to install virt-manager , to run a couple of virtual machines, i created a virtual nic vnet0 and bridged it to my eth0, i have configured the /etc/network/interfaces file with proper static ip, but i beleive the network manager is renaming my nic to eth1 and causing all kinds of problems. I uninstalled network manager and now i can ping anywhere in the network, but not outside it. ie google.com
I'm running Kubuntu 10.4. My problem is that Network Manager keeps defaulting back to Auto eth0. I have created a new wired connection and set my manual addresses. I have ticked the 'connect automatically' button. Every time I reboot or wake up it reverts back to Auto eth0.I did have wicd installed but this was not reconnecting after wake up (said it was connected but I couldn't ping etc), this is a pain also.
I used the network manager to configure my eth0 interface.It is working fine. I have found the nameserver entries in /etc/resolv.conf files. But the /etc/network/interfaces file does not carry the ip, netmask, gateway,network and broadcast entries. It only has a entry for the lo interface. where are the settings for eth0 as done by the network manager, stored in case of ubuntu?
I have a troubling networking situation that is compounded by the system being remote without any out-of-band mgmt in place nor a serial connection - but am relying on a coworker entering commands into the terminal for me, or doing stuff in the GUI I have an FC12 i386 install running, that was up and stable for 6 days. Primarily this was only being used for a deployment of nTop. Up through Monday evening, I was connecting to the system (in NY) via VNC (here in SF), and was successfully watching nTop do its thing.
Tuesday morning, I go to connect to SSH and I can't get in. The NAT translation is still in place on the firewall, but there is no connection to the NIC/eth0 from the router. This is what I've had my coworker run:
I was going to try and have her run the /sbin/mii-tool eth0 tomorrow a.m. just to verify that the interface isn't physically bad? But this is a brand new desktop, and I can't for the life of me understand why this interface went down. I also have the internal IP on a DHCP reservation, which is the same IP listed in IPADDR in the ifcfg-eth0 file - could this be a problem? should I remove the DHCP reservation? I did this so I could SSH to a public IP which I have NAT'd back to the internal 10.0.x.x address I had my coworker take a look at the GUI, and the eth0 properties are "inactive" and the "Activate|Deactivate" buttons are greyed out.I suppose I can have my coworker grab the /var/log/messages and copy to a USB drive, then email me that from another workstation.
i have installed kubuntu in ubuntu 10.04 lts, the problem that i have right now is that whenever the laptop hibernates the network manager is disabled!! so i always have to go to the ubuntu desktop enviroment in oder for me to activate the network kubuntu.Is there a way i can just activate the network manager without going to ubuntu desktop enviroment??
If I made a distro from scratch it would have been Lubuntu, cept I'm sure my theming would have been horrible. Now Ive installed on a couple of my Laptops, and even had a few friends convert, and for the most part everything is hunkus doris, cept one small issue thats keeping me from slapping it on my trusty laptop. I'm lost as to what the problem could be. Ive tried just about all I can think of, but I use sprint mobile broadband to connect to the net and then use Network Manager to share this connection with the laptops and Palmtops around the house. I can get my sprint modem to connect thats not a big problem the problem is now I cannot get the Auto Eth0 to connect to send out as a share. It just refuses to connect. Now this is not a Lubuntu problem at all Im sure its somehow a Lxde problem, as Mint Lxde, PeppermintOS, and so on do the same thing, refusing to connect Auto Eth0 while Sprint is connected. Any Gnome based distro this works flawless, as does Xfce distros, so Im sure this is somehow something within Lxde. Im sure its down to just "missing" a file or some stupid overlooked thing.
I am a ubuntu user and recently install kubuntu desktop in to it.In the ubuntu I am using gnome network manager which is very user friendly to connect Internet.But when I log to kubuntu I am getting headache due to that unfriendly network manager.Stillcouldn't connect to Internet in kubuntu.I heard that we can install gnome network manager tokubuntu. I go through several documentation in Internet and tried for that.And they all failed.most of the document describe to install it via online.But I cant connect to Internet through kubuntu.Is there any way to do that.Can I do it off-line or can I do it through Ubuntu(can I use Ubuntu synaptic package manager or terminal to install gnome network manager to Kbuntu ).If can how to do it.I am new to linux.
I'm trying to connect to the VPN of my employer; after fix various minor issues I reach this point in which the DNS entries and the default gateway of the VPN are overwritten with the values of the eth0 device that appears by default. Therefore the vpn is not useful.
I had trouble connecting to a wireless network with openSUSE, so I tried the YAST network manager to see if that fixed it. Not only did it not fix it, but now I cannot connect to any network, wired or wireless. I tried to open the default network manager and it said "Network management disabled". How do I re-enable it?I also have set YAST settings back to their originals with no luck.
I know I sound pretty nooby atm, but I'm thinking of making a switch to Kubuntu. But only if it has a software centre, similar to Ubuntu, I know Linux Mint has it now so I would expect same from Kubuntu (Y). I just cba to run off a live CD, I'm typing an important document atm.
Only problem is when there's no information to read I can't learn anything. So I've looked and looked but I can't find anything on the KDM theme manage that comes with kubuntu 10.10.
SO here's what I want to do:
All I want to do is just change the login and splash screens to something more to my liking when I got to System settings -> System Administration -> Login Screen , which is the KDM that comes on kubuntu (trust me I looked for kdmtheme under KpackageKit I get a chance to pick new themes I go through and find something I like and go to install and it doesn't show. All I get is the original one and that's it.
why it doesn't show up or how I may go about changing these two things
Last night while setting up wired & wireless connection in openSuse 11.2 Gnome version via YAST's ifup, I got wireless but lost wired connection (interface eth0). Dmesg shows that eth0 became eth1. I cannot get eth0 back. Is there any way to remedy this situation, eg. get info from the Ubuntu partition in my triple-boot laptop, without having to re-install openSUSE?
I'm new to this forum site and I was wondering how can I bridge a network between the eth0 and wlan0 connections?my eth0 NIC is a RealTek RTL8111B 10/100/1000 Ethernet Card (OnBoard) and my wlan0 NIC is a RealTek RTL8187B 802.11b/g WiFi USB Adapter Card.Are there any utilities, such as bridge-utils that I can use, except for Firestarter since Firestarter states that the eth0 connection is not established, or do I right-click on the network icon and select Edit Connections and go to Auto eth0 and under the IPv4 Address setting and select Shared to other computers and run a live connection there?The main reason is that I need an Internet connection for my Xbox 360, which is connected to my Linksys WRT54G 802.11b/g Wireless Router, that has DD-WRT firmware installed and 4 WiFi hotspots for any wireless device, such as my PSP, DS, DS Lite, Wii, Laptop(s), my brother's PC (needs a WiFi card), and my dad's PC (needs either a WiFi card or an Internet connection from my brother's computer to my dad's PC)
Here are my Computer Specs: ECS nForce6m-a Motherboard 2GB DDR-800 PC6400 Memory
I am running ubuntu 11.04 in classic mode with macubuntu theme and the avant window navigator. I am very impressed. I have downloaded kubuntu and have tried it from the live cd. The question I have, is can I also install this on my pc and choose at login which version to boot and do I install it from the cd at boot up or can I install it from the archive manager in ubuntu 11.04.
I am running Kubuntu 6.10. I opened adept package manager to create a new repository. It opened and I created the new repository (/home/dell/repository/)it went through. I closed adept. Opened adept and a error message reading this popped up: "The APT database could not be opened! This may because by incorrect APT configuration or some similar problem. Try running apt-setup and apt-get in terminal and see if it helps resolve the problem." I ran it in terminal (I was online) for both and update and upgrade in both apt-get apt-setup, but it tells me "E: type "/home/dell/repository/" is not known on line 1 in source list /etc/apt/sources.list E: The list of sources could not be read." I tried opening Add/Remove Programs but it did the same thing as adept. I am a linux newbie, and haven't toyed with APT database. When I added the new repository I just opened Manage Repositories and then entered "/home/dell/repository/", clicked add and it was put on the list as "Comment | /home/dell/repository/" in a grey text. I right clicked on it and clicked enable, it stayed grey. I left the program then. How can I fix the APT database?
I have been trying to lighten the load that Ubuntu uses on my RAM and processor, and decided to try LXDE, as it is the lightest-weight DE that I have tried and liked. I noticed I didn't have any wireless connectivty under LXDE, so I checked the LXDE site for the solution, and it said to download and install LXNM, which supports wireless connections. Unfortunately, installing LXNM (apt-get install lxnm) also uninstalled nework-manager, and network-manager-gnome, on top of lxnm not working properly, and stranding me without any way of reinstalling the OS, and without an internet connection (I can't connect with a wired connection, either). Is there anything I can do, aside from reinstalling?
When I log onto my Ubuntu 9.04 boot I am disconnected from the internet, on my windows 7 boot It works just fine, I have attempted disabling networking, power cycling the modem and router, and re-enabling networking, no dice though. hovering over the connection icon tells me that there is no network connection.
Opening the edit connections window tells me that there a wired connection called Auto eth0 that is set to never, and that is all that I can find. I hunted for other forums on this and found a few but none with a successful resolution.
So far as my knowledge goes, /etc/network/interfaces is supposed to contain a list of all the available interfaces. But my /etc/network/interfaces looks like this,auto loiface lo inet loopbackBut I have a perfectly working eth0 connection. Why does not it appear here?
Upgraded To Ubuntu 10.04 The Other Day. And when I first installed it everything worked great except for my sound card which I fixed. But there was no problem with connecting to my Router via an Ethernet cable. Then I updated the video card drivers, restarted my PC and it wouldn't connect. It would try over around 1-2 mins then tell me its disconnected. No green light activity on the router / network card either.
I've reinstalled fresh copies of Ubuntu a couple of times now, Hoping to get the default settings back. But nothing has worked since.
I looked around the net and found quite a few people had this problem on previous versions of Ubuntu but it would seem most of there fixes were for there Version, so it hasn't helped me.
Heres some info:
I've tried all the various things from dhclient to ifup/ifdown etc etc.
Trying to get the wired nic working so I can troubleshoot the wireless. I cannot get any kind of network activity. Been searching so I will post a little information that seems to be common with my situation.
lshw -C network
WARNING: you should run this program as super-user. *-network DISABLED description: Ethernet interface product: 82562EZ 10/100 Ethernet Controller vendor: Intel Corporation
I have recently upgraded the ubuntu desktop edition from 8.04 to 10.04. after upgrading i cannot show my eth0 nic interface in the System > Preferences > Network connections----- wired tab. and i also not getting network indication in the top of the panel beside the date time indication. but i can access network and using internet with that lan card. i cant understad my eth0 is connected or unpluged..
Since I installed ubuntu 10.04 I dont see my eth0 card in System->Preferences->Network _connections. Everything works fine but it puzzles me. In ifconfig iI just see the eth0, networking seems to be working fine, but it keeps puzzling me. Adding theinterface is no solution: add it and it doesnt show again
I am using BSNL broadband ISP and I am able to get network on windows os but not on my ubuntu.( I have a dual boot). I see Auto eth0 connected from the notification but when i am pinging [URL]... it says unknown host.
I tried for two days to install ubuntu server to my computer from a cd. Whenever I tried burning to a CD-RW (using two programs at highest and lowest speeds), my cd always said it had corrupt files. So I setup a virtualbox harddisk that was setup tonuse my slave harddisk and installed ubuntu server in virtualbox successfully. Now when I boot my server, it won't connect to my network. Long story short, I have taken lo out of my interfaces and tried resetting my dhcp ip address by releasing and renewing it using dhclient. I have realized that eth0 doesn't exist (it shows up in windows). I think that all I need to do is add eth0 to ubuntu...