Ubuntu Installation :: No Longer Use Monitor "out Of Range" After New Update

Jan 5, 2011

I am using an external monitor for my laptop to run Ubuntu with. I just updated Ubuntu today, but when it is about to reach the Ubuntu login screen, then the monitor says "out of range." Now, Ubuntu boots up into the GUI if I unplug my monitor and use my laptop screen, but I prefer to use the external display. I have tried all of the suggestions from my search results in Google. I did Ctrl + Alt + +, but nothing happens. I did Ctrl + Alt + -, but nothing happens.

I used Ctrl + Alt + F2 to get into a terminal to run the command: sudo dpkg-reconfigure xserver-xorg, but nothing happens. I believe there are supposed to be options to change the settings, but it does not even give me any. I tried to edit /etc/usplash.conf and /nano/etc/usplash.conf, but they do not exist. My monitor is a Westinghouse 22" LCD with resolution 1680x1050. It has been working for the past few months until I updated it today.

View 2 Replies


ADVERTISEMENT

Ubuntu Installation :: Updated To 10.04 And Now Monitor Frequency Is Out Of Range

May 1, 2010

I just updated my Wubi install of 9.10 to 10.04 last night. Everything went well until it required me to reboot the computer. I rebooted, loaded Ubuntu from the startup list, and then the screen went blank and I got "H.V. frequency over range" on the monitor.

I can load the GRUB options, but recovery mode using the most recent kernel does not work. I am entirely unexperienced with using the terminal and command prompt options.

Here's what I have attempted so far:

$ sudo dpkg-reconfigure xserver-xorg this did not do anything, the command was not recognized

$sudo nano xorg.config I don't even know what to do when I get to this screen

and I am about to try $ sudo displayconfig-gtk

I have an ATI Radeon 9100 IGP card

View 7 Replies View Related

Ubuntu Installation :: Can Not Run Live Cd Monitor Input Out Of Range?

Nov 7, 2010

this has happened with a few different attempts of ubuntu based distros lately ... i try to boot a live cd it gets to where it starts loading and the monitor pops off and says input out of range ... im aware that this is a known bug with xorg choosing either the wrong resolution or refresh rate ... but what the heck are we supposed to do , i can't get far enough into the boot process that i can open a terminal and try to bypass xorg ... so will all future distributions of ubuntu just be out of the question for me ? if you ask me what needs to be done is make the installer ASK what resolution you want to attempt to boot at .... similar to what puppy does

View 2 Replies View Related

Debian Installation :: Monitor Out Of Sync Range?

Jan 18, 2010

My last Linux install was SUSE 6 on an early ISA based Pentium clone. I'm used to Unix / bash from OS X, MinGW, QNX & BeOS... none of these rely heavily on X. But I'm thinking that Linux is so popular, I'm doing a lot of my Windows stuff under MinGW, why not just stick Linux on and be done with it.So I've polled the various distros, I'm a power-user / dev so Ubuntu doesn't seem like me, and I'm not familiar enough with Linux to go Gentoo just yet, but the way I slim Windows and OS X installs down to just what I need. I love apt-get and like FreeBSD installs I've seen, but want some Linux kernel goodness for my self, so I have chosen Debian.

I grabbed the amd64 build of lenny DVD 1, partitioned up and installed a bare system that I can apt-get the bits I want later.Here's the problem... When the install completes rebooting sends the graphical login to a frequency my old Hanns-G TFT can't handle.I can Ctrl-Alt-F1 back to the terminal or boot in single user mode, and everything seems to be good until you go GUI.Here's what I've tried.

I've renamed /etc/X11/xorg.conf to /etc/X11/xorg.conf.oldI ran dpkg-reconfigure xserver-xorgI've reinstalled using both simple GUI and Expert GUI using both kernelsI've tried adding nvidia-* packages with apt-get and aptitudeI remember there used to be a frequency tuner app for SUSE 6 and XFree86, but it seems that sort of thing is depreciated in modern Linux.Info? My GFX card is an nvidia GT 220, the motherboard is an ASUS P5QL Pro, the Monitor (Hanns-G) is attached via RGB HD-15 D-Sub (sadly that's all I have access to right now) and it's native resolution is 1280x1024 4:3 @ 60Hz, but in heXPee it will sync at that resolution at 60, 70, 72 or 75Hz, though it does get fuzzy at 75Hz.I'm fairly certain that X is working, just not at a frequency my screen can display... how can I fix this from single user, or regular bash terminal?

---edit--- Forgot to mention I ran dpkg-reconfigure on the XServer. :s It didn't offer video drivers, only to change from gb 105 keyboard layout and ps/2 mouse. I set the META key to the logo key while I was there, but it wasn't really helpful in any other way.

View 14 Replies View Related

Ubuntu Installation :: Clean Install Of Karmic - Monitor Out Of Range?

Jan 30, 2010

I've just installed Karmic and get an Out Of Range message on my monitor when starting.I had to use the alternate install in order to get Karmic on there in the first place.I have an Nvidia GeForce 7600 GS, and a BenQ FP767-12 TFT.

Output of lspci;01:00.0 VGA compatible controller: nVidia Corporation G73 [GeForce 7600 GS] (rev a2)Not sure how to get my xorg.conf as I can only get to a shell. Here are (what I think are) the important bits;

Code:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "screen0" 0 0
EndSection
Section "Module"

[Code]...

View 1 Replies View Related

Ubuntu Installation :: 2ond Monitor Does Not Detect - Shows Out Or Range

Feb 15, 2011

My brother got a new 120hz monitor, but can only get the old one to work. If he boots up with both of them connected in windows xp they work fine, but in Ubuntu 10 only the old one works. If he tries to detect the monitor in Display Preferences, nothing happens. The old monitor is connected to vga output (lcd with vga only) the new monitor is connected to dvi with a dual-link dvi cable. We know the graphics cards cannot provide 120hz, for now we run the monitor at 60hz until he upgrades the rest of the pc (sandy bridge i guess).The 120hz monitor worked fine until he changed graphics card from a ATI radeon 9200 to a geforce 3 ti 500.

He has tried

sudo dpkg-reconfigure xserver-xorg

and detect monitor in Display Preferences but no dice. Could he try restricted drivers?

System specs:

Ubuntu 10.04 32bit
athlon xp 1700mhz
1GB ram
ati radeon 9200
geforce 3 ti 500
lg w2363d

View 1 Replies View Related

Debian Installation :: Monitor Signals Out Of Range On Reboot

Mar 15, 2010

I am running an AMD Athlon 64 with an NVIDIA 6600 video built into the motherboard (PC Chips). My monitor is a 19" LCD with a standard VGA connector. I tried installing Lenny and everything went smoothly. However, when I rebooted, the monitor said "Signal out of range." I had this happen with a live CD of another distro too.

View 1 Replies View Related

Fedora Installation :: Cannot Install Core 10 Monitor Out Of Range?

Jan 15, 2009

I cannot install Fedora core 10. It boots up and it gets to the Fedora 10 loading screen. After that it complains my monitor is out of Range and that's as far as I can go. I had originally thought I could get to some text install mode, but I don't make it far enough to do that.

View 1 Replies View Related

Fedora Installation :: Monitor Setting Caused Out Of Range

May 12, 2009

I think the settings in /etc/X11/xconf.org are wrong. I do know what the settings should be and have SSH access, (root plus password). Being new to linux I cannot figure out how to save the file after editing. I have been using: vi /etc/X11/xconfig.org to get to the file, but haven't been able to save the file.

the edit and save commands I need, I hate to do an entire install since this is about my 6th install.

View 2 Replies View Related

OpenSUSE Hardware :: SuSE 11.3 Installation : Monitor "out Of Range"?

Aug 7, 2010

I am installing SuSe 11.3, and during the initial boot after installation, I got "out of range" message on the monitor and nothing happens afterwards.My PC is dual CPU (intel), Video card is " nVidia N240GT" and the monitor is Gateway flat screen "FPD2485W".I tried both interfaces (gnome and KDE) and got the same problem ("out of range")

View 4 Replies View Related

Fedora Installation :: 14 Monitor "Out Of Range"

May 20, 2011

I run Windows 7 on my home PC and I recently installed Fedora 14 on my USB. When I boot from the USB, I see the Fedora loading screen (3 bars overlaying each other), but once its fully loaded and goes to move forward, both my monitors go blank, one says "Out of Range", the other "No Input".

View 1 Replies View Related

Ubuntu Installation :: No Longer Login After Update?

Feb 28, 2011

I am having a problem with the latest update of lucid ubuntu. I was on 10.04 for the longest time but decided to update while I was out doing errands. When I got back the logon screen was made up of blue and gray windows on a completely black background and the mouse and keyboard wouldn't work!

I found that if I unplugged and then replugged my mouse that I could get it working, but not all the options work properly. When you try to close a menu it just stays up, but it isn't there at the same time. Also, the shutdown/restart options don't work along with the physical power button on my computer, I have to remove the battery and power cord to shut it down.

I am currently dual booting ubuntu and windows 7 on my gateway NV59 laptop.

View 9 Replies View Related

Ubuntu Installation :: Update Manager No Longer Working In 11.04?

May 11, 2011

I recently tried to add a repository by following the directions here: Banshee.fm/download and then select the ubuntu icon at the top. Here is the error I get when I try to run update manager: "Could not initialize the package information An unresolvable problem occurred while initializing the package information.

Please report this bug against the 'update-manager' package and include the following error message:'E:Type 'banshee-team/ppa/ubuntu' is not known on line 1 in source list /etc/apt/sources.list.d/banshee-team-ppa-natty.list'The command I entered was sudo add-apt-repository ppa:banshee-team/ppa. I have tried to remove all banshee related checks in software sources of the ubuntu software center. Then I just removed the lines all together. I still cannot open update manger. Get the same error. Anyone know of a fix?

View 6 Replies View Related

Ubuntu :: Monitor Frequency Out Of Range - 10.04

Oct 16, 2010

I've recently reinstalled a computer with 10.04 for my parents to use, and it worked fine at mine, but after transporting it to theirs and hooking it up to their existing monitor it doesn't seem to work anymore!Well, it boots and I hear it login but I don't get a splash screen and at some point between the bios and the login sound it comes up with Frequency out of Range. On the warning message it displays a frequency of "72.9 kHz / 90.2 Hz" but in the monitor settings its reporting that its operating at horizontal 64,0 kHz and vertical 60.0 Hz. I also don't get any splash screen when starting up, just a flashing _ before the monitor stops things

What I can do however is drop into a the tty console (alt+ctrl+1) and login to the shell but don't really know what things to change from there.Having googled things a bit I've found references to xorg.conf but there's no such thing on my system so I can't edit that to fix this. Likewise I also have found references to fiddling with grub to get into the recovery, but grub doesn't even appear when I boot and I don't know what to press to get it to drop into its menu...

This is really urgent as I need to go home tomorrow at the latest and I want to get my parents system working before then. I also have no spare monitors here and I didn't think to bring with me a liveCD to fiddle with things (only a UNR netbook which I'm posting this from), so the console is the only access I have to the machine.Some specs: Ubuntu 10.04. ATi Radeon 9100 IGP, no proprietary drivers are installed. The monitor is an old CRT that still works beautifully and whose replacement is not an option.

View 3 Replies View Related

Ubuntu Installation :: Grub Update - Can No Longer Boot Vista

Feb 27, 2010

I recently installed Ubuntu (Karmic Koala) on a Dell Inspiron 1525 which already had Vista installed on it. The installation went just fine and I could boot into either Ubuntu or Vista using the Grub bootloader options. After updating grub through the update manager however, I can no longer boot into Vista and get an error message that says:
"Windows cannot start. A recent upgrade or hardware change may have caused this".

And below that:
File: \boot\bcd
Status: 0xc000000e
info: An error occurred while attempting to read the boot configuration data"

When I run sudo fdisk -l, I get the following:
Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000080

Device Boot Start End Blocks Id System
/dev/sda1 1 6 48163+ de Dell Utility
/dev/sda2 * 7 13619 109345113+ 7 HPFS/NTFS
Partition 2 does not end on cylinder boundary.
/dev/sda3 13619 15936 18605117+ 7 HPFS/NTFS
/dev/sda4 15937 19457 28282432+ f W95 Ext'd (LBA)
/dev/sda5 19066 19457 3148708+ dd Unknown
/dev/sda6 15937 18930 24049242 83 Linux
/dev/sda7 18931 19065 1084356 82 Linux swap / Solaris

Partition table entries are not in disk order. I have the Vista recovery disk but was wondering whether using it to repair the Vista bootloader might mess up Grub.

View 4 Replies View Related

Ubuntu :: Monitor 'out Of Range' With Black Screen Msg

Mar 6, 2010

i tried to install linux mint, at first i got 'out of range' with black screen msg but used compability mode and got past it and installed mint on my HD. a moment after it updated my nvidia drivers and after reboot I got the out of range message again, which leaves me in the situation where i cant do pretty much anything I tried editing xorg.conf added VertRefresh 60-75 and Modes "1440x900_75.00"

View 4 Replies View Related

Ubuntu :: Monitor Input Signal Out Of Range / Fix It?

Nov 28, 2010

I basically destroyed my laptop a couple of years ago. Windows XP wouldn't even start but it didn't come with an installation disk. I tried recovering it but it just died. So a few months ago I put a box of thing on top of it which broke the screen! I was going to chuck it out until I stumbled upon a page which told you you could use it as a web server.

I decided to use it to host my website. I installed ubuntu without a problem however it wasn't until I was about to start it up I found out it was against BT's terms and conditions!! So since I installed ubuntu I thought I might as well make use of it and use it to render my files. When I went to turn it on for the second time and plugged it into the monitor it said input signal out of range!

I can see the login screen but I can't move the mouse or anything. I can't access the terminal, how can fix this?

View 9 Replies View Related

Ubuntu Servers :: 11.04 - Out Of Range Error On Monitor

May 7, 2011

I just installed Ubuntu server on one of my computers, but when I boot up the screen goes blank and the monitor gives me an 'Out of Range' error. I understand that this means that the resolution settings are too large for the monitor, but I don't understand how to change them, since there is no GUI installed. Details:

Monitor:

LCD
Recommended Resolution is 1280x1024

I have also tried it on another monitor with a recommended resolution of 1920x1080, This also gave me an OOR error. Ubuntu Server version 11.04

View 6 Replies View Related

Ubuntu Installation :: After Update, Windows 7 No Longer Auto-Detected By GRUB2?

Apr 23, 2011

I'm using Maverick Meerkat, 10.10, 64bit. I'm a pretty basic user but am trying my best to learn.

My background: I have a laptop on which I installed Win7 Ulimate on one partition. After installing Win7 I then installed Ubuntu on a separate partition. GRUB2 found both Win7 and Ubuntu perfectly. I could choose to boot into either one and the ability for GRUB2 to "remember" which OS I booted into last worked properly. I then did a kernel update a couple days ago via Ubuntu's Update Manager. After that, GRUB2 could no longer see Win7. I added a custom boot entry in /etc/grub.d/ so that Win7 would show up in GRUB2.

However once Win7 did show up in GRUB2 I kept having a problem with the Windows bootloader being missing. I used the Win7 Recovery DVD to get into Windows and then installed EasyBCD for Win in which I was able to create a Win7 boot entry and get the Win7 bootloader back. I set EasyBCD to skip the bootmenu so my current configuration now is that on bootup I see GRUB2, which shows Maverick Meerkat & Win7. If I select Win7 then Win7 loads via EasyBCD and it works fine.

The problem though is that GRUB2 does not auto-detect Win7 AND it no longer remembers the last OS that I booted into. I would rather not use EasyBCD if I can help it and would like to just use GRUB2 for everything.

My question is this: How can I get GRUB2 back to controlling Ubuntu & Win7 properly without the need for anything else in between. I have asked in the Freenode Ubuntu channel but haven't received any help besides "sudo update-grub" which I have done and it hasn't helped.

View 9 Replies View Related

Debian :: Starts Up Out Of Range From Monitor?

Jul 2, 2010

i just did a graphic install of debian lenny and when i finished the installation and restarted the computer the grub boot menu appeared and i selected debian and nothing happened the monitor just displayed a message saying "out of range" i have a dell studio xps 1800is it my graphics card (it shouldn't be) how do i start x server in a different resolution (if screen resolution is the problem

View 9 Replies View Related

Hardware :: Monitor States Out Of Range?

Aug 4, 2010

I have recently got the Linux bible 2010 and it came with a cd and dvd containing multiple distro's of linux. I have tried them all with the same problem. Everything until the actual GUI desktop shows up from the live disks as well as an actual debian install, when I get to the desktop however out of range shows up. I have a video card hooked up, figured that might be the problem, it was not. I tried the on-board video and it also did the same thing. I also tried a different monitor, which did not work.

View 3 Replies View Related

Hardware :: Out Of Range Error On Monitor

Oct 4, 2010

I am a Windows Server guy trying to stay afloat on this Linux installation I am doing so please bear with me. I have installed RHEL 5 and installed the updated NVIDIA 256.53 certified driver. Upon rebooting everything was great. I got to the X server login and entered my user name and password. The very next thing I see is "Out of Range" error on my monitor. I know that I needed to verify that my xorg.conf file had the proper refresh rates specified in it for my monitor, which I have done.

View 3 Replies View Related

General :: Monitor Resoluti8on - All Out Of Range

Mar 28, 2010

the electric went off and when it come back on my monitor picture was all out of range. I changed the resolution to bring the picture back in and now the words are almost unreadable.

View 1 Replies View Related

Ubuntu Multimedia :: Warsow: Monitor Says 'Out Of Range' On Start?

Mar 15, 2010

I am on ubuntu 9.04. I have nVidia 8500GT and I installed Warsow 0.5 today.When I start the game my monitor goes black with a message "Out Of Range"I can only hear the music.I tried hitting a few keys here and there and I could also hear the tutorial start.

View 1 Replies View Related

Ubuntu :: Error Resolution Out Of Range On Computer Monitor

Oct 14, 2010

I have an hp vs17e monitor and I am running slax linux But I have absolutely no idea how to fix the error resolution out of range on my computer monitor.it then shuts off and I can turn it back on and it'll do the same thing.

View 1 Replies View Related

Ubuntu Installation :: Update Manager No Longer Works Post Upgrade To Lucid

May 28, 2010

When I run update manager, it gives me an error message saying:

Code:

This can be caused by:
* A previous update which didn't complete
* Problems with some of the installed software
* Unofficial software packages not provided by Ubuntu
* Normal changes of a pre-release version of Ubuntu
if I click partial upgrade, it looks like it did during the upgrade, then says:

Code:

There are no upgrades available for your system. The upgrade will now be canceled.
if I click close from the first "not all updates can be installed" dialog, it says:

Code:

It is impossible to install or remove any software. Please use the package manager "Synaptic" or run "sudo apt-get install -f" in a terminal to fix this issue at first.
running the suggested line gives the following output:

Code:

In Synaptic, fixing broken packages does nothing. Mark All Updates > Apply seems to work, but I'd still like to figure out why Update Manager does not?

View 7 Replies View Related

Hardware :: ATI Driver Install / Monitor Out-of-range

Jun 15, 2009

I have tried installing the ATi drivers via the 1-click install process, however when I get to init 3 and try to run sax2 (sax2 -r -m 0=fglrx) my monitor just goes out of range. I have tried this in both OpenSuSE 11.1 and 11.0 - both the same. I have tried running sax2 with the -l switch for low resolution - no change. I have also tried the switch "--vesa 0:800x600@60" and "--vesa 0:1024x768@60" which are known resolutions/requencies that this monitor supports (the latter is the native resolution) - no change.

I have tried another monitor but it's exactly the same. My video card is an ATi Radeon HD2600AGP and is correctly identified by OpenSuSE, and displays video fine using the default driver.

View 17 Replies View Related

Ubuntu :: Monitor Out Of Range Noob Dual Boot Pita?

Jul 6, 2011

I just installed ubuntu in a dual boot with Windows 7, I have a new emachines pc compact with 3gb ram 2.8 amd processor, and nvidia 6150 integrated. I cannot see the boot menu, so now I cannot go back into windows anymore becaue I am receiving the message "monitor out of range change to 1600x900" so it just automatically boots into ubuntu. I have searched alot on this topic, and have tried giving terminal commands specified for thiis issue, but the termnal does not recognize the commands. I am logging in and am typing "sudo" before I go into configutration. I am BRAND NEW to linux and am really struggling with this.

my monitor is a 4 month old HP 2010
Display size
50.8 cm (20")
Display type
Wide Thin Film Transistor Liquid Crystal Display active matrix
Aspect ratio

[Code]...

View 2 Replies View Related

Ubuntu Multimedia :: Fglrx Driver For ATI Card Pushes Monitor Out Of Range?

Feb 21, 2010

fglrx driver for ATI card pushes monitor out of range

I am running Ubuntu 9.10, my video card is ATI Radeon HD 3600

Heres my issue:

When I originally attempted to enable desktop effects, I was told that I was unable to do so. Not being one to rush to ask a question, I tried to figure out the issue, and it seemed to be that I needed to install the fglrx driver available for ATI cards- a simple enough fix. I installed the driver, and rebooted my machine, and everything seemed to be fine- the initial splash page came up- but immediately afterwards (presumably when I reached the login screen) My monitor went out of range.

Not being strong in coding, I was unable to figure out a way to remove the driver without a GUI (though I think I very well could have), so I had to uninstall and reinstall (no sweat, I hadn't really started anything yet). However, its obvious that the fglrx driver is what blew it out of range.

My question is, is there anything I can do to get this driver to work on my machine? I found similar questions but they all seemed either to be slightly different from my issue or recommended changing the .xorg file, which does not exist in 9.10.

View 9 Replies View Related

Debian Hardware :: AMD Quad M4A785TD-V: Monitor Freq Out-of-Range, Blank Screen?

Mar 14, 2010

Last Thursday, 3/11, I installed a new mother board (ASUS M4A785TD-V EVO), AMD Athlon II X4 Processor, 4Gig DDR3 ram (RIP JAWS), 1 SATA DVD drive, along with my 2 IDE HDD's. The display was OK during BIOS review, and boot UNTIL it came to mounting x-graphics, at which point the screen went black, and a display message came up saying Out-of-RangeHf: 30KHz-70KHzVf: 50Hz-90HzCurrent Frequency:90.3KHz, 60.0Hz.

Does anyone know what is causing this? I mean, is there no way that Deb 5 X86 is going to run on a quad 64-bit system, or can something else be wrong? Before changing hardware, I had seen indications that this system was backward-compatible to older systems, and the more in depth study I've done since seems to verify this.y be, however, that I completely mis-understand what I am reading - this is all pretty new to me.

I tried booting into Debian 4, Libranet 3, and Linspire 6. They all complained loudly, but differently, about x being inoperable. I can't tell you how they complained because I can't go back and check them. THAT is because, in BIOS, I was testing the system with all the different options for "Internal Graphics", to see if one would work. One of these options was "Disabled". Oh-ho-ho! BAD MOVE!!! it's disabled, all right, including BIOS! I can't believe it. There was no warning, whatsoever. I assumed no engineer in his right mind would allow that option to lock out the BIOS without SOME kind of warning. I'm going to try to call ASUS tech support tomorrow to see if they have a solution, but if anyone knows how to reverse this, please let me know. I suppose the only answer is a separate graphics board. But I don't want to get that if I can't use this MotherBd.-processor setup.

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved