Ubuntu Installation :: Regular Update On 9.10 Breaks USB Printer?

Feb 10, 2010

I did an update during a time when power was cycling due do a nasty snow storm, but I'm pretty sure the update was completed successfully before I lost power. What did happen though is that my BIOS setup was reset.

Now if my HP Laserjet 1020 is plugged into USB during boot all other USB devices freeze for a while. So I played with my BIOS setting for USB:

- Enabled V1.1 and V2.0
- Disabled System USB Shadowing

So now my bootup doesn't hang. But now when I actually go into Karmic I still can't print.

dmesg shows the following:

[ 205.940008] usb 1-10: new high speed USB device using ehci_hcd and address 9
[ 219.510026] hub 1-0:1.0: unable to enumerate USB device on port 10
[ 223.430008] usb 1-10: new high speed USB device using ehci_hcd and address 10
[ 223.600766] usb 1-10: configuration #1 chosen from 1 choice

[Code].....

View 4 Replies


ADVERTISEMENT

Debian Installation :: Upgrade To Lenny Breaks The Printer

Feb 11, 2010

I just upgraded to lenny (stable) from a working etch system. It went pretty nicely but I'm having a problem with the print system.

Ok, I have an HP Laserjet 4M+ connected to my system by USB. (I have another color printer too and a scanner but I don't use them often).

I use CUPS. I never bothered with the HPLIP packages because straight cups has always worked well.

What happens now is that I'll send a job to the printer and nothing will happen. The printer won't get it. Looking at CUPS on the localhost:631 page I can see that the printer is on, connected, ready; the job is there too but just stuck on "processing".

Now here's the thing. If I manually load the ehci_hcd module with "modprobe ehci_hcd" then the job will make it to the printer and it will print.

I can't just make that module load at boot time because if I do and the printer is off, it doesn't work. (I have to unload it and reload it). For whatever reason, I have to make sure that module gets loaded AFTER the printer is turned on, or nothing gets sent to the printer!

View 10 Replies View Related

Ubuntu :: Kernel Update Breaks Installation?

Mar 5, 2010

It seems that updating the Kernel breaks my installation. I've tried it twice, and both times it disabled my gui desktop. I'm posting this with links2 in my terminal. The terminal works perfectly.

This is really annoying, as I can't even use my computer. What do you think is the problem?

View 6 Replies View Related

Ubuntu Installation :: Recent Update Breaks Remote Control?

Jul 17, 2011

My mythbuntu 10.10 system including its lirc managed remote control has been working fine.I've recently done some updates (see below) and now the remote doesn't work correctly (only some of its keys seem to work). I suspect that lirc is no longer managing the remote and now instead the remote is now being treated like a keyboard.How do I get lirc managing my remote control correctly again,Before the updates the kernel was:

Code:
$ uname -a
Linux pvr 2.6.35-28-generic-pae #50-Ubuntu SMP Fri Mar 18 20:43:15 UTC 2011 i686 GNU/Linux

[code].....

View 2 Replies View Related

Ubuntu Installation :: Regular Update Now Can't Boot From HD Or CD?

Oct 7, 2010

I updated my Ubuntu 10.04 on Dell 1330 and on the next boot it failed. I get a series of messages, the main point seems to be that it can't find the files it needs to mount.I tried booting from the live cd I used to install 10.04, but it can't boot either due to wrong user id error and maybe trying to boot from wrong kernel?At this point I am willing to just wipe the hard drive and do a fresh install but how to do that if I can't run the install cd?Or is there a way from initramfs to solve this?I tried mount /dev/sda1/mnt but it says cannot read /etc/fstab no such file.libdevmapper

View 9 Replies View Related

Ubuntu Installation :: Update - Error - PkgProblemResolver:Resolve Generated Breaks - This May Be Caused By Held Packages

Oct 10, 2010

I'm trying to update my Ubuntu 10.04 to 10.10... But I get this error message:pkgProblemResolver:Resolve generated breaks, this may be caused by held packages

I tried to disable all the repositories, and also "sudo apt-get -f"... But still having this error message...

View 8 Replies View Related

Ubuntu Servers :: Apache Update Breaks PHP

Oct 20, 2010

I updated my server (Ubuntu 10.04 LTS) today and had about 23 updates in Webmin. After the update suddenly apache doesn't render php pages anymore, instead letting you download the source code for the scripts. I checked the logs and found this:

Code: Syntax error on line 1 of /etc/apache2/mods-enabled/php5.load: Cannot load /usr/lib/apache2/modules/libphp5.so into server: /usr/lib/apache2/modules/libphp5.so: cannot open shared object file: No such file or directory I tried reinstalling php5 but I can't get it to work. I also hope that this was a glitch and that updates that break stuff like this don't get through QA.

View 9 Replies View Related

Ubuntu :: 10.04 Amd64 Grub Breaks After First Update?

May 28, 2010

a fresh install of 10.04 all worked well installed apps as i wanted all went well... system update download completed no restart required... restarted anyway only get grub prompt... repeated this operation twice.... how do i fix getting fed up with ubuntu promising easy of use ...

View 6 Replies View Related

Ubuntu Installation :: Printer Yields Only Error Message Since Update

Feb 24, 2010

Sometime during the morning of Feb 23, 2010, I accepted Update Manager's updates on both my desktop and my laptop, both of which are running Karmic and both of which have been regularly updated by Update Manager. Before the updates, which I think I saw included an update to CUPS, my Brother MFC-8820D printer had been running satisfactorily.

Since the updates, all the printer yields, in response to my attempts to print from either my desktop or my laptop, is the following six lines:
ERROR NAME;
configuration error
COMMAND;
setpagedevice
OPERAND STACK;
--dicttype---

Assuming I'm correct that CUPS was updated on Feb 23, is there some way to find out what the latest CUPS update involved, and/or how to return to a prior version?

View 2 Replies View Related

Ubuntu :: Kernel Update Breaks Suspend On Lenovo SL510

Dec 23, 2010

I just updated my kernel to the latest version (2.6.35-24). Now my suspend function on my Thinkpad SL510 no longer works. The system simply hangs with a solid cursor in the corner of a black screen. USB devices remain powered on, HDD keeps spinning, and all indicator lights remain lit. When this happens, the only thing I can do is hold the power button down for a hard power off.My first thought would be to troubleshoot this with dmesg, but I don't know how to record dmesg after a power off. The message buffer is reset when I reboot.

View 1 Replies View Related

Fedora :: YUM Update Breaks Nvidia Driver

Mar 11, 2010

I updated my fedora 12 GNOME installation. Now Compiz fusion is not working. It says Accelerated 3D support not found. Though Nvidia drivers are already installed. Now I can't even ALT+TAB between open applications.

I tried "metacity -- replace" but then windows wore a weird look with only a minimize button. No sign of maximise & close buttons.

View 14 Replies View Related

Fedora :: Update Breaks Gnome Shell?

Aug 14, 2011

I updated last night and after a reboot I can get the GDM login but as my desktop loads it suddenly stops and complains of an error and won't load. If I load legacy Gnome desktop with Compiz it loads but ALL the lettering and words on the interface are messed up. By this I mean the letters are upside down and the words are spelt backwards. The mouse menus also work in reverse as in the menus themselves are also upside down and the highlighting moves from bottom to top as I move down the menu. Amusing but not what I want from my computer. There is nothing in /var/log/messages or /var/log/Xorg.0.log that would indicate anything is wrong.

I sooo don't want to have to rebuild, again, because of instabilities in F15 updates.

View 10 Replies View Related

OpenSUSE Install :: Update From X11:Xorg Breaks X?

Mar 2, 2009

I just got a set of updates from Xorg11 (Index of /repositories/X11:/XOrg/openSUSE_11.1/i586) repository and now, my X doesn't come up. During update, zypper complained about xorg-x11-libxcb and it didn't get updated. On further investigation I noticed that libxcb-xlib.so.0.0.0 is missing in the new package (version 7.4-4.2. The one currently installed in 7.4-1.24).

View 9 Replies View Related

Debian Installation :: When Connect The Printer, Doesn't Recognize Printer As The Photosmart B109 Printer For Unknown Reason?

Jan 3, 2011

I've bought a HP Photosmart printer, HP Photosmart wireless e-All-in-One printer - B110a and i've got a problem installing it properly. I'm using Debian 6.0 Squeeze. When i connect the printer, Debian doesn't recognize my printer as the Photosmart B109 printer for unknown reason. When i go to the site of HP and search for a driver, it directs me to this site:I've downloaded that latest hplip file as a .run file and installed it. My printer is recognized proparly, but when i try to print a colored image, it comes out black/white. Something is not crrect. Does anyone recognize this problem with this type HP printer?

View 7 Replies View Related

Ubuntu Installation :: Mythbuntu System Hangs After Regular System Update: "out Of Memory" Errors

Aug 4, 2010

I have Mythbuntu 10.04 installed on an exclusive HTPC and working great... until tonight. After letting the system update some packages (161 packages if I remember right), I suddenly have an issue where the graphical system won't start. After researching I found three error messages that might be causing that.

1. At the start of splash screen I see "UUID=xxxxxxxCD7 not ready yet or not present" I checked in /etc/fstab and found that this is the swap partition. I don't remember seeing this before so this could be the culprit.

2. I'm not at the computer in question right now but I saw a Plymouth error about "mountall" and then the message "plymouth command failed". Not sure if this could be the main error.

3. after a while (usually ca. 1-2 min) I receive thousands of errors of the kind "out of memory"... "kill process XXXX" (process vary wildly e.g. dbus-daemon, mysql, etc)... "process killed"..."respawning"

After error 3, I'm not able to switch to graphical console (ctrl-alt-F7). If I was in the graphical console at this moment, I simply can't switch to the CLI console. I'm always afraid of updating my system since I've seen lots of things breaking afterwards (usually the proprietary graphic drivers) but this is really strange.

View 1 Replies View Related

Ubuntu Networking :: 2.6.35-24-generic Kernel Update Breaks Broadcom STA Driver

Dec 29, 2010

I upgraded my Linux kernel from 2.6.35-23-generic to 2.6.35-24-generic and the Broadcom wireless STA driver stopped working. If I try to reinstall it with Jockey it fails and shows this in the log:

[Code]....

View 3 Replies View Related

Debian :: Squeeze Update On 2011-07-21 Breaks Grub?

Jul 22, 2011

yesterday I updated my squeeze amd64 on my Phenom X4 and now it is not booting anymore. Have you experienced the same problem?

After that I noticed the shutdown was not working anymore, it just restarted instead of powering down. This morning it wouldn't boot squeeze anymore, when grub starts and prints "Welcome to grub" (or something like that) the list of operating systems is not shown.

I noticed the updated also included grub and I saw it correctly detected my operating systems.

I am planning to boot knoppix soon and try to reinstall grub from chroot, but currently I am at work.

View 2 Replies View Related

Fedora :: Latest Chromium Update Breaks Flash V10.0.42.34

Dec 24, 2009

I installed Chromium via a repo generously maintained by Tom "Spot" Callaway. Since it's his repo I thought I'd contact him, but I don't really know how - so I'm brining my issue to the forum to see if anyone has a possible solution.I've been using Tom's Chromium fine for the past couple months. After a "yum update", Flash no longer works in Chromium. It works in Firefox. If I try to play any Flash videos it's just a blank box.

View 3 Replies View Related

Fedora :: Update To F14 Breaks Gnome Icon Theme / Why Is So?

Nov 3, 2010

After I had upgraded the system to Fedora 14, the icons for pretty much everything except for programs and plain text files in gnome theme (and every other theme that shares them) became inaccessible - they are replaced by a standard icon that appears when no other is found. Other themes, that share no icon with gnome (tango, gnome-colors, etc.), work correctly. I'm using Xfce desktop.

I've deleted icon-theme.cache, but it did nothing.

Any suggestions, what may be causing this?

View 7 Replies View Related

Fedora Hardware :: Wlan Breaks After Kernel Update

Aug 8, 2011

I run an Aspire One 522 with a Broadcom BCM4313-Wlan-Card and Fedora 15. To run the card, I had to install der broadcom-wl-Driver, as described here: [URL]... It worked okay. (Althought not perfect. It crushed everytime the whole system, when it tried to connect to a WLAN-Net, unless I first started the Windows on the computer, then shut it down and restarted Fedora. But maybe thats some strange Dual-Boot-thing.) Anyway. After I updated the Kernel to 2.6.40 it seems to be broken. I deleted the driver, reinstalled it, tried the B43-driver. But no mater what: It seems like the NetworkManager doesn't find the card at all. lsmod shows that a modul "wl" is running. And - as mentioned - I installed the Kernel and the two other packages fresh form the repositories.

View 3 Replies View Related

Networking :: Lighttpd Breaks After Large System Update?

Feb 24, 2010

I am not fully sure if this belongs more to the networking section or the software. O hope it is related to here enough.

My problem is as the topic says.

My port 80 seems to be already taken. lighttpd fails to start reporting that it cannot bind to port cause its already taken.
The error message itself:

Code:
"Starting web server: lighttpd2010-02-21 07:01:02: (network.c.345) can't bind to port: :: 80 Address already in use failed!"

I am not able to crack this by myself. Ihve tried investigating this by

Code:
lsof -i :80
netstat -ape | grep -v unix

First doesn't show anything second anything abt port 80.

Now hints I can think of. Maybe you have more experience and ideas what I can do and where should I look for the culprit.

I am using debian (unstable) and lighttpd. I even tried rebooting; it says that the port is taken already at the boot sequence (well it starts pretty much at end anyway but the system should be clean).

It seems that it started failing after a major distro update, so maybe there are some conflicts based on ipv6/v4 or something, though I have no idea what it could be. Well my hit for that is the part of error msg "bind to port: :: 80 ". This "::" looks like ipv6 naming convention. Maybe its lighttpd internal.

View 2 Replies View Related

Debian Configuration :: Squeeze Update To Network-manager Breaks Functionality

Feb 7, 2010

I have just updated my Squeeze system. The update included a newer version of network-manager (and it can not be more than a few hours old). After the update all network functionality on my machine (via knetwork-manager) is broken. The GUI applet has no effect.

Hence can anyone help me: a) Downgrade network-manager by one version; b) Find out what is causing knetworkmanager to break; c) See if the problem is with knetworkmanager or network-manager.

View 5 Replies View Related

Debian :: Difference Between Regular Lenny And 'update' ISO?

Jun 6, 2010

I was looking through the Debian FTP site, and noticed
debian-504-amd64-DVD-1.iso

and with a modification time only about 24 hours later,
debian-update-5.0.4-amd64-DVD-1.iso

Whats the difference between these two?

View 1 Replies View Related

CentOS 5 :: Xen Not Starting - After Doing A Regular Software Update On A 5.5 Box - And Rebooting

Jun 21, 2010

After doing a regular software update on a 5.5 box (and rebooting), I now have problems starting xen (version "xen-3.0.3-105.el5_5.3.x86_64").

Running "/etc/init.d/xend start" yields no output, and checking the script, I see that the script halts if "/proc/xen" doesn't exist.

Checking the filesystem, I find that the "/proc/xen" entry is indeed gone. Restarting the CentOS box does not help.

Should I reinstall Xen? If so, should I remove any portions of Xen before I do?

Update:

When I run /usr/sbin/xend I get:

View 2 Replies View Related

Ubuntu :: Wireless Stopped Connecting - Applying Regular Updates Via Update Manager

May 9, 2011

My self-built PC had a BT wireless adaptor in it which worked, albeit after a bit of a faff, with Ubuntu 10.10 in connecting to my BT HomeHub2.

When I came to use it last week it would not connect. I'd not changed any hardware but I had been applying regular updates via Update Manager.

Bearing in mind the "faff" factor, I decided to try a different (Edimax) wireless card but got the same result. Upgrading to 11.04 has made no difference either.

It does *try* to connect but fails, so I think the card is installed correctly. I've also tried a full reset on the HomeHub and the setup works fine with W7.

View 6 Replies View Related

Fedora :: Knetwork Manager With The Update - Stable And Robust Enough For Regular Use?

Nov 18, 2009

I'm running Fedora 11, and just did an update of the system. It looks like there was an update to the package that takes care of knetwork manager. In the past, I have played around with it, but it hasn't met my needs, so I went back to nm-applet, which works fine.

I'm curious about the update, and would like to see if it works. However, knetwork manager won't start as there is another network manager already running (there is a message about this everytime I log in). I can easily kill nm-applet, but logging out and back in causes it to reload, and I still get the message from knetwork manager. So here are my questions:

1) With the update, is knetwork manager stable and robust enough for regular use (the docs for F11 said it wasn't upon F11 release, so included gnome's network manager as the default network manager)?
2) How do I get knetwork manager to work (I presume this means I turn off Gnome's network management and switch to knetwork management)?

View 2 Replies View Related

Ubuntu :: VirtualBox Kernel Module Breaks After Each Kernel Update?

Jan 6, 2010

I'm running Virtualbox from the Sun website (need the USB support) and it breaks after each kernel update.The problem is that I installed a lot of Ubuntu systems for transitioning windows users with Windows in virtualbox to ease the migration but I have to rerun vboxdrv setup after each kernel patch.

View 2 Replies View Related

Ubuntu Installation :: Setup USB Printer On Lucid Without Printer Connection?

Aug 3, 2011

I'm setting up a netbook for somebody (in another country!) and one of the last hurdles is the printer setup. I only have the netbook and not the printer with me. I know that the printer is a HP PSC 1215 All-In-One Printer but there seems to be a Catch-22 that I need to have the printer connected in order to be able to set this up using the GUI tools. How do I work around this? As a minimum I just want to enable printing, although scanning would be a bonus.

View 1 Replies View Related

OpenSUSE Network :: Stunnel Update Breaks Programs Using Stunnel (11.4)?

Jul 30, 2011

I received stunnel 4.40-0.6.1 as an update from "zypper up" (openSUSE 11.4).After a reboot, stunnel does not work anymore for the programs that need it.Symptom: the program (emacs+mew) hangs for ever, telling me

"Creating an SSL/TLS connection..."
/var/log/messages does not contain a clue and restarting stunnel via
"rcstunnel restart" looks fine:

[code]....

View 8 Replies View Related

Ubuntu Installation :: 9.10 Breaks ATI X-1950 Pro

Jan 31, 2010

I just upgraded to the new 9.10. In 8.04 when I went into "Restricted Drivers" it showed something for my video card. Now there is nothing.

I'm trying to play a game (Counter-Strike) and it's just too laggy, probably because I don't have any drivers installed for the video card.

It's an ATI Radeon X-1950 Pro. What can I do?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved