Ubuntu :: Can't Connect To Wired Network

Jun 18, 2010

I can get my desktop to connect to network on the router its plugged into.

View 1 Replies


ADVERTISEMENT

Ubuntu :: 8.10 - Cannot Connect To Network (Wired Connection)

Feb 11, 2010

I just installed ubuntu 8.10 on my pc. Before was XP installed. I formatted the system and installed ubuntu. Installation was successful. Problem is that I cant connect to network. My network card: realtek 8139 ethernet card

On ifconfig I get:
Code:
eth0 Link encap:Ethernet HWaddr 00:16:76:af:23:b3
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:23 Base address:0xb800

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:502 errors:0 dropped:0 overruns:0 frame:0
TX packets:502 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:31896 (31.8 KB) TX bytes:31896 (31.8 KB)

Also the connection is wired one with modem only it's reliance broadband. The wire is connected between modem and pc but there is no blinking of light for this connection. The wan is active and wan's light is blinking and when I was on xp on same pc there was no such problem.

View 4 Replies View Related

General :: Wired Network Won't Connect Ubuntu 10.04.2?

Feb 23, 2011

I have a new install of Ubuntu 10.04.2 and the network will not connect. This is a dual boot desktop system with Vista. The Vista network is good. When I boot up Ubuntu, the network icon seems to be searching but then the message "Wired network disconnected - you are now offline" appears. I ran ifconfig -a & got:

eth0 Link encap:Ethernet HWaddr 00:1d:09:7b:b5:29
inet6 addr: fe80::21d:9ff:fe7b:b529/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

[code]...

View 5 Replies View Related

Ubuntu :: Can't Connect To A Wired Or Wireless Network?

Aug 11, 2010

I have a laptop with Ubuntu 9.04 on it. I wanted to try out fluxbox, so I did a apt-get install fluxbox. When I went into fluxbox, I was having trouble getting connected to my network wirelessly. I saw a post online that said to install wicd. So I did a apt-get install wicd. This removed the Gnome network manager (nm-applet) which I didn't realize that it would do. I removed wicd when I saw this is what happened, and now I can't connect to a wired or wireless network. I tried connecting to my wired network, and I ran

Code:
sudo ifconfig eth0 192.168.1.115

but I still can't access the internet, or other things on the network.

View 2 Replies View Related

Ubuntu Networking :: 10.04 Cannot Connect To The Network - Wired Or Wireless

May 5, 2010

I have just installed Ubuntu 10.04 on an HP Pavilion dv6000 series laptop, dual-boot. Everything is working except the networking. It can see wireless networks, and when I type in the password for my wireless network, it tries to connect, then asks for the password again. When I plug in the Ethernet cable, again it tries to connect, but after a few seconds gives up and tells me I am now offline.

View 8 Replies View Related

Ubuntu :: Cannot Connect To Wired Network (wireless Works)

Sep 17, 2010

I rebooted my machine, and now I can't connect to the wired network for some reason. Wireless works fine.

Code:
eth0 Link encap:Ethernet HWaddr 00:18:f3:5a:66:70
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0

[Code]....

View 5 Replies View Related

Ubuntu Networking :: 10.10 Doesn't Connect To Wired Network

Jan 9, 2011

I just finished installing Ubuntu 10.10 64bit. During installation Ubuntu was connected to the network and was downloading updates. After rebooting though, it cannot connect to the network.

View 1 Replies View Related

Fedora Installation :: Connect With The Wired Network

Jul 7, 2009

I installed Fedora 11 on my computer with the live cd. If I run the live cd, the network connection is active. But, after the installation the cannt connect with the wired network. I must use an internal Server to connect the www. The server controlls my mac address and if it correct, the server allow the connection. ipconfig and the network manager can read the correct mac address. Why it does not work

View 1 Replies View Related

Networking :: How To Get It To Connect To Wired Ethernet Network

Mar 4, 2011

Just installed Scientific Linux 6. Does anyone know how to get it to connect to wired ethernet network?

View 3 Replies View Related

Ubuntu Networking :: Wired Network Active But Cant Connect Online?

Feb 20, 2010

Yesterday I moved my modem (wireless) to my living room so the PS3 detected a better signal. In doing so, I had to run a new ethernet cable from my living room where the modem is into my office where the computer is. I use ubuntu 9.10

For some reason I cannot connect to the internet now. When I scroll over the connection, it says wire connection 1 is active. I have my settings manually set. I did notice the MAC address field is blank...

I didn't have an issue before, but with changing cables and whatnot, something got messed up somehow.

View 1 Replies View Related

Ubuntu Networking :: Unable To Connect To Any Network Wired Or Wireless

Nov 30, 2010

I am unable to connect to any network, wired or wireless. Network-manager and wicd are both gone, as in no longer installed. Please don't tell me to apt-get anything. I have no network connection. I have tried downloading packages for nm onto a usb stick only to find myself in dependency hell which ended with the impassible error "Requires installation of untrusted packages".

View 6 Replies View Related

Ubuntu :: Unable To Connect To Network (wired LAN Connection, No Wireless)

Jul 14, 2011

I've just installed 11.04 Natty on an old Laptop (Dell Lattitude C400) and am unable to connect to my home network (wired LAN connection, no wireless). The laptop previously had WinXP installed and was able to connect (I have also double checked the cables and ports and they're all functioning ok).

sudo lshw -C network

Code:

*-network
description: Ethernet interface
product: 3c905C-TX/TX-M [Tornado]
vendor: 3Com Corporation

[code]...

View 9 Replies View Related

Fedora Networking :: Cannot Connect To Wired Or Wireless Network F14

Apr 29, 2011

F14 did not recognize my wired or wireless NIC upon installation. I have enabled network manager, what should I do from here? Here is my hardware specifications:

Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01)
Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05)

View 11 Replies View Related

Networking :: Connect To A Windows Computer Via A Wired Network?

Feb 15, 2011

cannot connect to my window computer using open SuSe

I am attempting to connect to my Windows Computer via a wired network on a sky router. When I tried with PClinuxOS it configured automatically. With the latest version of open SuSe 13.1this is quite a bit different. I have got as far as the network being auto and active with an Icon showing on the taskbar. However when I click on the Windows network Icon SuSe tyies to locate my Computer but then comes back with " failed to reteive share list from server. This is as far as I can get after several hours of trying.

View 1 Replies View Related

Fedora Networking :: Wired Network Won't Connect Automatically After Upgrade

Jun 11, 2010

I just upgraded to Fedora 13 (from 10, using preupgrade), and I've gotten most things working again, but I'm still having trouble with the network.My wired connection (eth0) doesn't connect on boot (even though ONBOOT=yes in /usr/sysconfig/network-scripts/ifcfg-eth0).Because of that, I figured I'd just leave eth0 connected manually (with ifup eth0). However, I then found that if I try to connect to a VPN like this, the system reverts to the "stalling every time I try to connect to the internet" problem that I had earlier.

View 1 Replies View Related

Ubuntu Networking :: Unable To Connect To Wireless But Can Connect To Wired

Nov 2, 2010

I am unable to connect to wireless network in ubuntu 10.10.i have noticed that the iwlagn driver isnt been used by anything.

View 9 Replies View Related

Ubuntu Networking :: Cannot Connect To Wired And Wireless In 10.10 It Tries To Connect But Fails?

Jan 10, 2011

in linux world and have recently downloaded and installed ubuntu desktop 10.10i cannot connect to both wired and wireless ethernet on my laptopit tries to connect but fails in 30 seconds , it says"disconnected" while i am able to connect to the same in windows i have broadcom 4315 and i have tried both fwcutter and ndiswrapper but the problem persiststhe device id is 14e4:4315

View 9 Replies View Related

Ubuntu Networking :: Network-Manager Tries Always To Autoconnect To Wired Network

Feb 18, 2010

I have the problem with my notebook, that, after I used it at work, the network-manager always tries to autoconnect after boot. He has no cable network and so I get the message "not connected" after a while.how to tell the network-manager, not to autoconnect each time?

View 4 Replies View Related

Debian :: NetworkManager Applet Shows No Network While Connected - Wired Network Device Not Managed

Oct 30, 2010

I'm running Squeeze and I'm looking 3 days now for a solution in some weird problem. The NetworkManager Applet shows that there isn't connection although I am connected. The icon has this small "x" and when mouseover it says "No network conncection". Moreover when left clicking it, it says

"Wired Network Device not managed"

While I was looking for the solution a came across this post by an Ubuntu developer who says:network-manager-applet displays the connectivity state of network-manager's managed interfaces not every interface. So the title "network manager says disconnected but is connected and working" is actually misleading. The interface is connected and working but not from network-manager's point of view since it is not managing the interface. Additionally, in Lucid now network-manager applet displays nothing now for non-managed interfaces so is less misleading. You can check to see whether or not an interface is managed by network-manager by using the command line too nm-tool. You'll see "State: unmanaged" for unmanaged interfaces.

View 14 Replies View Related

OpenSUSE Network :: Lost Wired Network Interface Eth0

Feb 14, 2010

Last night while setting up wired & wireless connection in openSuse 11.2 Gnome version via YAST's ifup, I got wireless but lost wired connection (interface eth0). Dmesg shows that eth0 became eth1. I cannot get eth0 back. Is there any way to remedy this situation, eg. get info from the Ubuntu partition in my triple-boot laptop, without having to re-install openSUSE?

View 3 Replies View Related

OpenSUSE Network :: Network Wired / Wireless Not Working

Feb 11, 2010

I can not get my network to work.Wireless shows no networks at all and wired the ethernet light does not even turn on. I have dpne heaps of searching but i can not seem to find a solution.

View 6 Replies View Related

Ubuntu :: Connect To The Internet With A Wired LAN Connection?

Jan 11, 2010

I have been trying to connect to the internet with a wired LAN connection for a while now with no luck. Running version 8.04 LTS on a 32-bit desktop. Interestingly, my 64-bit desktop running version 8.04 64-bit automatically connected to the internet with no problems or input from me. Both are connected to the same router.

I figured i'd try and copy the network manager settings from the 64-bit machine to the 32-bit machine, which involved setting an automatic configuration (DHCP}. All went well except no DNS server address showed up on the 32-bit system, despite there being one on the 64-bit system. Trying to run Firefox like this results in the 'page load error' page coming up immediately.

I then manually added the DNS server address from the 64-bit system to the 32-bit system, and all that did was prolong the time it takes for the 'page load error' page to appear.

View 1 Replies View Related

Ubuntu Networking :: Cannot Connect Wired Or Wireless On 10.04

Apr 30, 2010

I just did a fresh install of ubuntu studio 10.04 and I can not connect to either a wired or wireless network. The In Network Tools the IPv4 IP address is 127.0.0.1. It is plugged into a network giving out DHCP IP's. Both wired and wireless were working on ubuntu 9. I have tried to bring eth0 up in the terminal but it did not give an error or anything. It it running on a Dell Latitude D820 laptop.

View 3 Replies View Related

Ubuntu :: Wired Internet - Can't Connect To Modem

Aug 28, 2010

I have wired internet, but I can't connect to my modem. I have cable internet (Comcast) but my computer can't detect it. I do not know what do to. Tried a whole bunch a things, but I'm a novice, (Ubuntu 10.something I tried to call but they say everything was okay and I keep telling the Comcast lady I had Ubuntu, but apparently she insisted I had Windows. I thought they were not very smart, so I gave up on them.

View 4 Replies View Related

Ubuntu Networking :: Connect Dsl & Wired Connection With NM?

Sep 1, 2010

The situation is I have one machine just installed 10.04yesterday, and I plan to take it as FTP server sharing filesvia LAN and WAN as wellBut after setting up all network withNetwork-Manager found that my dsl connection willdisconnect while my wired connection was connected.

my network-manager setting process is:
1.wired tab:
IPv4:192.168.1.x

[code]....

View 2 Replies View Related

Ubuntu Networking :: Can't Connect To Wired Router?

Oct 23, 2010

I wanted to try Ubuntu again but have gone wayback to an old 8.10 disk because I couldn't get 10.10 to work. The install with 8.10 went fine but the internet will not connect. The network manager shows eth0 grayed out and when going in to manage the connection it says 'never'. I'm using Vista with a broadband modem connected to a netgear router.

View 3 Replies View Related

Ubuntu Networking :: Connect To The Internet ('Wired')

Mar 26, 2011

I am a Ubuntu novice who recently shifted completely to Ubuntu 10.04 from Windows 7 on my Dell Inspiron Mini.

1. I am able to connect to the internet ('Wired') at home but when i plug in the internet cable at work it is not connecting. It gives me the message 'Unplugged, you are now disconnected'.

2. I tried installing the Wicd network manager. Even though there are wireless networks in range it doesnt show me the wireless networks (like it used to show in wiindows).

I have read through a long list of commands in the forums of commands to be executed and executed them all but couldnt connect. Is there anything basic that I am overlooking?

I thought that wired network should work once I plug in a network cable irrespective of the place. How come I am unable to connect to the network at work? I used to have a windows 7 partition and the net connected plug and play when i was in the windows side. I dont want to install Windows just for the internet at work again.

View 9 Replies View Related

Ubuntu Networking :: Connect To The Wired Connection Using 10.04

Apr 20, 2011

i can't connect to the wired connection, but i can connect to the wireless... i'm using Ubuntus 10.04. when i run this codes into the terminal it shows:

root@valdivia-laptop:/home/valdivia# sudo lshw -C network
*-network
description: Wireless interface
product: AR9285 Wireless Network Adapter (PCI-Express)
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:04:00.0
logical name: wlan0
[Code].....

View 9 Replies View Related

Ubuntu Networking :: Wired And Wireless Won't Connect?

May 5, 2011

I have recently developed a problem with my computer connecting to the internet which has totally stumped me and is currently forcing my to use windows much to my frustration. I am using ubuntu 10.04 on a Toshiba Satellite laptop. My wireless and wired network connections will not connect. They are all present in the menu and i can click on them but the connection tries to connect and then just times out and fails to connect. Everything still works fine in windows Vista. The more confusing thing is i tried some live disks to see if they would work but they all did exactly the same thing including a live disk of ubuntu 9.10 which used to work perfectly and live disks of openSUSE 11.4 and Mint 10. I struggling to tell if this could be a hardware problem or not. The fact that the live disks wouldn't work suggests a hardware problem but the fact that Vista still works totally throws that argument. I have looked all over these forums and elsewhere and have found some similar ish problems but non seem to have the severity of this one as all of those seem to be wireless only problems. The only thing that i was doing at the time this started was i had just set up a new secondary user account but i suspect that may be coincidental.

View 4 Replies View Related

Ubuntu :: Cannot Connect Wireless Through Wired Router?

Aug 13, 2011

I have searched and found no answer to this one. I have a Linksys DSL router BEFSR41 (wired) which works great. I recently got a Linksys Wireless-G Broadband router. Which also works great with my Dell mini 10 netbook running 10.04. I have two computers (wired) also running 10.04, what I want to do is use both routers with only one internet DSL connection. I have the wired (Master Router) connected to the wireless (Slave Router) and I fire up the Dell it sees it and connects but I can't connect to the internet. I can connect through my network and share files through all 3 machines. Do I need to reset the wireless, to enjoy the internet? If so the wireless came without instructions or CD.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved