Red Hat :: Fatal Server Error No Screens Found On RedHat 7.1 XFree86
Apr 4, 2009
there are several posts related to my problem but not quite what I want. I don't need any effects to be running nor do I need perfect resolution. I have a PCI-E card Nvidia 8600 gts and I need to run redhat 7.1 for reasons that are not debatable. I also have an onboard ati radeon X 1250 but currently I am running the PCI-E.The installation was successful and ran in GUI, however after installation and reboot, the screen keeps flickering trying to load the desktop.I just need to get the GUI running the same way the installer was able to run in GUI, I tried editing the XF86Config file to change the driver to either vesa or vga but still didn't work. Probing for devices is not an option since the card is not listed and the maximum video ram goes up to 64MB in xconfigurator. It probes my card as a VGA generic with 1 MB ram. I know there is a way to have the desktop load just the same as the installer's gui settings but that's where I need help.
this is after changing all the 'driver' values to vesa. I don't understand why it can't find the screen even though I used the horizontal and vert. sync values for my monitor. Any instructions or advice on how to just get the desktop loaded would be great, I know this is a very old OS but regardless I need for it to work.
Ubuntu 10.10 Whenever I try to boot up now I get a command line environment instead of the normal gnome desktop. The first error message that comes up is: "Screens found,but none have a usable configuration" further down: "Fatal server error: no screens found" Any way I can re-configure so it detects my monitor?
I've installed 9.10 on a work station with success. I've got an nvidia quadro fx 3000 and its supported under nvidia legacy driver apparently. So I've tried to install the driver with no success. Xorg.0.log reports a fatal server error no screens found. I get a flashing console login when I boot with "nvidia" device driver in xorg.conf, it boots fine with "nv". No matter what I try I cant get it to boot with nvidia drivers. Also, on a side note, after initially installing nvidia driver thru hardware in gnome, I no longer have a grub loader option to select recovery or anything else. Upon boot it displays "grub" briefly then continues to boot to gui. I've set the delay to 20 seconds with no results.
Resolved the issue of the display, now on to the grub menu.
I have just upgraded from 11.1 to 11.4. When I boot up, I get a command line, but when I do 'startx', I get 'Fatal server error: no screens found'. I have been looking for a solution and tried 'Xorg -configure' but this gives:
Code: Failed to load /usr/lib/xorg/modules/drivers/vboxvideo_drv.so: undefined symbol: resVgaShared
My issue began with my resolution changing to 800x600 in Karmic Koala and then my inability to change it back to anything else. In my haste to fix it before going to work this morning I loaded a new xorg.conf without backing up the old xorg.conf with data not relevant for my monitor and now I'm in limbo. The good news, I hope, is that I also run 8.04 on the same computer so I do have access to what I hope is proper xorg.conf / I've modified the existing xorg.conf file and I'm still getting the "low graphics mode" message (EE) problem parsing the config file and (EE) Error parsing the config file. Fatal Server Error: no screens found.
I have this old box that I used at school that I wanted to re-purpose and use. So i decided to that I wanted to run xp, ubuntu studio and slackware so I can learn about linux and do some other things with xp. I think I got through the installatiosa all fine and dandy, and I installed grub for my boot loader, I can boot into studio and xp, but I cant get into slackware. the grub boot menu is sorta funky too, it shows a generic and recovery mode for studio which is fine, and then another option for xp, some memory test boot option, but then for slackware it shows "Slackware Linux (Slackware 13.1.0) (on /dev/sda4) four times in a row. If I select any of them they all end up with some error; the third SW [slackware] option down the list of the repeated 4 allows me to sign into root, but when I type "startx" i get :
(EE) intel(0): No kernel modesetting driver detected (EE) Screen(s) found, but none have a usable configuration
Fatal server error: no screens found
but thats with a lot of other text above that. if you need any more details, please dont hesitate to request for them. I'm going to take some time and cool down. I'm trying to get these three OSes running from one HD. I've partitioned the 80 gig drive as follows
Primary 40 G NTSF for XP Primary 2G Linux Swap Primary 16G Slackware Primary 18 U Studio Primary
I must say, the RPMfusion version of the Nvdia driver package work better with FC10 than they did under FC9 for me, which is to say: they work at all. Still get corrupted output after a few hours of work, but I imagine that's just the underlying weakness of the Nvidia driver bubbling up. Either way, now I have other problems:
First off, the Intel driver for my onboard video setup has stopped working entirely. The attempt to bring up X on the Intel setup gets me to the KDE login screen and locks the machine up hard (poweroff required). A look at the xorg.0.log shows that the server seems to be stuck in a loop trying to determine the valid video properties for the session.
Here's my xorg.conf, BTW. I have it setup to perform different configurations depending on which DefaultServerLayout line gets uncommented (lines 4 - 6). If anybody has a better way of doing this, I'm all ears. While we're on my xorg.conf, pleas view lines 64-67 and/or 75-77. This is my quickie way of changing drivers (again, all ears) which brings us to the next problem, neither the nv or nouveau drivers work with my system. Interestingly enough, both drivers tend to fail in the same relative spot in the process, I think. Please refer to line 207 of this xorg.0.log with the nv driver or line 140 of this xorg.0.log from the nouveau setup. Either way, both sessions die with the same message: (EE) Screen(s) found, but none have a usable configuration. Fatal server error: no screens found Gotta go, x session getting corrupt,,,
I just installed Maverick on a brand new system last Saturday. Everything worked, except dual monitors, so I activated the proprietary ATI/AMD driver. That allowed the dual monitors to work, except that it put a little "AMD unsupported hardware" watermark in the lower right-hand side of each screen. After a day or two, I decided to go back to the default driver while trying to figure out how to avoid the watermark.
I assumed that when I deactivated/removed the proprietary driver that it would automatically switch back to the default. Instead, my computer now boots to TTY1, and when I try to install xserver.xorg, etc., I get a lot of error messages,ike "No screens found" or "Screens found, but configuration is unusable," etc. The same messages show up in the logs.Can anyone help me get back to a useable desktop display? At this point, I don't care which one. erhaps the proprietary would be easiest since it seems to be holding my system hostage, but either one would work.
husam@ubuntu:~$ compiz setting manager compiz (core) - Error: Screen 0 on display ":0.0" already has a window manager; try using the --replace option to replace the current window manager. compiz (core) - Fatal: No manageable screens found on display :0.0
Launching fallback window manager Window manager warning: Buggy client sent a _NET_ACTIVE_WINDOW message with a timestamp of 0 for 0x1e000b4 (Mozilla Fi)Window manager warning: meta_window_activate called by a pager with a 0 timestamp; the pager needs to be fixed. Now, if i close terminal, window's will be bugged .
I downloaded the new gparted (6.4.1 I think) and when I try to run it from a live cd in the default settings it keeps telling me that it can't find my screens. I have an intel video card. I haven't had this problem with older versions of gparted. I suppose I could use an older version, but I'd like to know what the problem is.
I am novice in linux and I have installed linux ES in my previous window desktop it was working fine. I try to make a bootidisk and system is not booting anymore. Following error I am getting at the booting time.
Running Ubuntu 10.10 x64, fully updated kernel and stuff, in VMWare Workstation 7.
Before I tried installing the Nvidia driver, I set up all my stuff, settings, etc. Restarted several times, everything went okay.
I then decided to install the Nvidia drivers for my GTS 250. I first tried the manual install (sudo sh NVIDIA-INSTALL-NAME.run) and it failed saying something about the nvidia.ko or nvidia.so. I tried using this page http://ubuntuforums.org/showthread.php?p=9203671 to fix it, but it still failed, so then I used the automatic method (sudo apt-get install nvidia-current) and it installed fine, then I ran nvidia-xconfig and restarted.
The VM started up, but no GUI came up, instead, a black screen with a terminal (I think it's called a Virtual Terminal) came up and asked me to log in. I tried the command "startx" from there, and it told me no screens were found.
while booting with bootsplash turned off there's a message "FATAL: Module ata_piix not found FATAL: Error running install command for ata_piix" .Though everything works fine i'd like to know what does this message mean and is there a way to disable loading of ata_piix whatever it means.
I installed debian 4.0 (etch) on an old computer with some pickled graphics card in it, and then I upgraded the computer to one with slightly newer hardware only without the graphics card (the new one used on board graphics). I moved the hard drive from the old one to the new one but when I booted it up it failed to start the X-server and I got some errors listed for "device not found" and "no screens found".
I tried using "dpkg-reconfigure xserver-xorg" however I can't seem to find a working configuration. It seems pretty silly that when installing debian it can detect all this automatically with no problems but when it comes to changing some hardware around you are left in the dark with a complicated re-configuration process. Is there not some way to automate this? I'd rather not have to re-install everything
Boot up with 2.6.32 kernel. Get to login screen, X attempts to start and fails. I log in, execute startx and succeed. Yesterday, could not boot up at all with .30 kernel. Upgraded to .32, so partially fixed. Yesterday also un-installed Synaptics package, as do not have touch-pad on this machine (Thinkpad X40)
This from kdm.log: X.Org X Server 1.7.4 Release Date: 2010-01-08 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.32-trunk-686 i686 Debian .....
I'm installing a NVIDIA driver and encountered some error message. Please see below the sequence (I've set runlevel to init 3);
linux:~/SuSe # rpm -ivh NVIDIA_GLX-1.0-4191.suse81:i586.rpm Preparing... ############################ [100%])file /usr/X11R6/lib/modules/drivers/nvidia-drv.o from install of NVIDIA_GLX-1.0-4191 conflicts with file from package XFree86-server-220.127.116.11-21
I have got xorg and gnome-core installed. When I put in command startx I get the following message: X: warning; process set to priority -1 instead of requested priority 0 Fatal server error:Server is already active for display 0 If this server is no longer running,remove /tmp/.X0-lock and start again. when I try to sudo Xorg -configure it shows me same message server is ..... lspci shows me the following information 04:02.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)So what I am doing wrong and how do I get this videocard working with Xorg.
I have VIA/S3G unichrome IGP video card of 32MB after installing fedora i am getting very worst resolution of 600x400which is completely irritating so please provide me a way out from this problem to use fedorathe solutions i followed and failed are given below
1. Some one told me to change the xorg.conf file but i failed because there is no such file in the given location
2. Some one told me to create it using system-config-display but for fedora 14 there is no package for that
3. some one told me again of using the command Xorg -configure but it said as followed [root@localhost tmp]# Xorg -configure
Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again.
I am having a strange problem with the Opensuse 11.2 Xorg server. Graphics hardware is Nvidia Quadro FX-5000, driver is ver 190.53. 90% of the time, I am getting a seg violation from the Xserver on trying to login via kdm:
...is the error that is present in the "kdm.log" file. So far, it doesn't seem to be user dependent (happens either as root or joe random user,) Again, so far, it only seems to happen with "driver nvidia" enabled in the config file, not with "driver nv" The failure occurs shortly after hitting return on the login screen. After it fails, it starts up a new Xserver, and presents a new login screen. Repeated attempts seem to *eventually* succeed, but 90% of the time, it fails I strongly suspect the Nvidia driver, but I have not been able to find anything documenting any similar problems.
This box is running 10.04 server, it's been running perfectly for almost 6 weeks. It's only function in life is running MailArchiva which is an ediscovery package, runs very well. Anyhow, yesterday the boss tells me he wants to do something else so the last thing I did was an apt-get update and an apt-get upgrade, no errors were observed, I seem to remember like 8 updates were available, this is what I've normally done in the past to keep it current. The last thing I did after that was shutdown -r now.
This morning I can't get into the box, I reconnected a monitor to it and this is the error I'm getting when it stops after about 9 lines into the boot process; modprobe: FATAL: Error inserting padlock_sha (/lib/modules/2.6.32-24-server/kernel/drivers/crypto/padlock-sha.ko): No such device. This is a mystery to me, the system is not encrypted. The only stuff that is belongs to MailArchiva. Anyhow someone evidently made off with my install cd so I am downloading another to see if I can repair this but I have no idea what broke.
I'm using with success NX server and client on Ubuntu 11.04 on both side. Yesterday the server crashed and now the client can't connect to it. The client works well because if I try to connect to an other server it works well and if I try to connect to this server with an other user it works well. So I think that there is a problem with my user. I have tried to solve the problem as explained in the details of the error. Unfortunately there is no file /var/log/messages so I can't search the code of the exception.
Code: NX> 203 NXSSH running with pid: 3877 NX> 285 Enabling check on switch command NX> 285 Enabling skip of SSH config files NX> 285 Setting the preferred NX options NX> 200 Connected to address: 10.1.0.60 on port: 22 NX> 202 Authenticating user: nx
I have server 10.04 running, and I modified my fstab file to automatically mount an NTFS partition on startup, but after a reboot, I see that I clearly did something wrong, as now it will not boot. The output is:
init: ureadahead-other main process (923) terminated with status 4 If this is an error with my changes to the fstab file, is there any way I can access is to change it? No matter what i do I can't get it to boot.
I have 3 accounts setup on this machine. One is root, one is my own, and one is for my kids. My account and root work fine, but today when I tried to log my kids on, startx fails (it also fails from runlevel4). I have tried creating new accounts and they fail as well. I'm not sure when the issue started, but it's been less than a week I believe. The consistent error which I receive is Quote: