OpenSUSE Wireless :: Unable Build Rt73.ko After Upgrade To 11.2

Jan 21, 2010

On my opensuse 11.1 system. I used my tp-link tl-wn321g usb wireless adapter to access the internet. It runs on rt2501 chipset and I used the serial monkey rt73 driver from here.

Code: [URL]

What I did was I installed the kernel-headers, kernel source, gcc and make. And then I cd to the module directory and did

Code:
make
make install
modprobe rt73

And then I configured the network with yast.

That was until I upgraded to 11.2 using the guide here.

Code: [URL]

The upgrade went well, but I could no longer use my wireless adapter. I tried installing the driver again but when I tried to run "make", it says

Code:
make: *** /lib/modules/2.6.31.8-0.1-pae/build: No such file or directory. Stop.
rt73.ko failed to build!
make: *** [module] Error 1

I've checked that kernel-headers, kernel-source, gcc and make are all installed.

I installed "ralink-firmware-1.1-1.5.noarch.rpm" from Software.openSUSE.org. I tried "make" again, but still the same error return.

View 9 Replies


ADVERTISEMENT

OpenSUSE Wireless :: Unable To Build Rt73.ko After Upgrade To 11.2?

Jan 25, 2009

On my opensuse 11.1 system. I used my tp-link tl-wn321g usb wireless adapter to access the internet. It runs on rt2501 chipset and I used the serial monkey rt73 driver from here.

[URL]

What I did was I installed the kernel-headers, kernel source, gcc and make. And then I cd to the module directory and did

Code:
make
make install
modprobe rt73

[Code].....

I installed "ralink-firmware-1.1-1.5.noarch.rpm" from Software.openSUSE.org. I tried "make" again, but still the same error return.

View 3 Replies View Related

General :: Unable To Net With Build In Wireless Card On Laptop?

Feb 6, 2011

I am getting obsessed with Linux OS up to the point of starting to swap MS OS.I opened WICD and it show (Wired network = 0 wired-default VVV and wireless network = C STR ESSID ENCRYPT BSSID MODE CHNL is this meaning that build in wireless card is or is not recognized? I will keep looking for info, although is hard to learn a new OS from scratch.

View 4 Replies View Related

OpenSUSE Wireless :: Build Up A Connection To A VPN Provider Using Profile Openvpn And Kvpnc?

May 8, 2010

Is there any way to run successfully umtsmon with kvpnc? Trying to build up a connection to a VPN provider using his profile openvpn and kvpnc. It connects as "low level connection" , the indicator of kvpnc remains red, but then kvpnc would not pass the network traffic through umts-mon (or better vice versa, umtsmon doesn't). In principle I would like to pass both interfaces (wireless, umts) through vpn.

View 4 Replies View Related

OpenSUSE Hardware :: Unable To Build Kernel Module For NVidia On A Fresh 11.4 Installation?

Mar 13, 2011

I'm trying to install the nVidia driver for a fresh Installation of OpenSUSE 11.4 (32-bit) but I'm running into some issues. I followed the instructions (SDB:NVIDIA the hard way - openSUSE) using the driver binary mentioned in the workaround link (NVIDIA DRIVERS 256.53 Certified) but the installer fails while building the kernel module with the following errors:

Code:
nvidia-installer log file '/var/log/nvidia-installer.log'
creation time: Sun Mar 13 17:32:56 2011

[code]....

View 7 Replies View Related

Ubuntu Networking :: Unable To Use Wireless After 8.10 To 10.04 Upgrade

Nov 28, 2010

I have an out-of-the-box Belkin G wireless router. I also have a Linksys USB adapter on a particular box. When I run the Ubuntu 8.10 live CD on that box I can see the router's SSID, I supply the password, and all is fine. I think that rules out any problems with the router or the ISP.

When I run the Ubuntu 10.04 on that same box I can still see the SSID but when I try to connect to it the DHCP fails. Checking the system logs I see the DHCPDISCOVER entries but no corresponding DHCPOFFER responses. So this seems on the surface to be a DHCP problem. To get around this I tried to edit the connection to use manually supplied settings. On the 8.10 system I supplied:

Code:

IP=192.168.2.200,
Netmask=255.255.255.0
Gateway=192.168.2.1
DNS=192.168.2.1

and again all worked just fine. But when I supply the same values to the 10.04 system it does not work. Even attempts to ping the router (192.168.2.1) fail. So if this fails then perhaps the problem is more fundamental than DHCP? I have tried searching the net for quite a while and found a number of similar problems, but clear solutions seem to be lacking (or I haven't come across them). One common suggestion is to blacklist the ipv6 module. I tried that and it seemed to have no effect. Since this worked so well in 8.10 and doesn't work in 10.04.

View 9 Replies View Related

OpenSUSE :: Find All The Build-deps Or What They Are For That Matter To Build Boxee

Feb 20, 2010

I'm in love with my Opensuse 11.2. Love my KDE 4.4. The only thing I miss from my Ubuntu installation, is the ability to use Boxee. I would be more than willing to compile Boxee from source. I only have 2 problems with that:

1) I don't know where I can find all the build-deps or what they are for that matter to build Boxee.

2) I'm running on a Netbook. Yes, my measly Intel Atom is no fun for compiling and building.

What are my options/what can I do to get Boxee up and running on 11.2? I've tried searching on build service for an RPM, but I think due to legal restrictions, Boxee can't be on there.

View 9 Replies View Related

OpenSUSE :: Build Libevent-dev 2.0.10 In Ooder To Build New Version Of Transmission?

Feb 16, 2011

looking for LIBEVENT... configure: error: Package requirements (libevent >= 2.0.10) were not met: In order to build transmission 2.21.I need libeventnew version of transmission,I need to build libevent-dev >= 2.0.10 and installed first.But I can't get any information about building development files for libevent.

View 1 Replies View Related

Ubuntu Networking :: Unable To Connect (wireless) Since Upgrade To 11.04

Jul 19, 2011

What has changed to the wireless function and possibly the use of the ndiswrapper in 11.04.

I originally install ubuntu 9.10 and immediately upgraded to 10.04. I have just now decided to upgrade to 10.10 and then to 11.04. Everything went ok and all still worked fine up until the upgrade to 11.04.

I've checked my settings and they are fine. The power light is still on my wireless card but no connection?

View 7 Replies View Related

OpenSUSE Wireless :: Wireless Card Detected But Unable To Scan The Network

Oct 27, 2010

1 ) make and model of wireless device Athreos 5k

2 ) driver version in use dont know

3 ) any error message. -

abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down

4 ) what you have tried to rectify the problem.

Tried to install all the patches.

5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies

6 ) openSUSE version 11.3

7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)

Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]

[code]....

View 9 Replies View Related

OpenSUSE Wireless :: Unable To Enable Wireless On Laptop Even Though It's Not Grayed Out

Mar 30, 2011

I am using OpenSuse 11.4(32 bit) on my Lenovo B460 laptop, and as the title points, am unable to use wireless on it. The 'enable wireless' option from icon menu is not greyed out, however clicking it does nothing, it remains disabled.

lspci -vv shows:

"04:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
Subsystem: Broadcom Corporation Device 0510
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

[code]....

so it seems that opensuse knows my hardware but networkmanager doesn't! I have all broadcom packages installed as well as kernel-firmware installed.

View 9 Replies View Related

OpenSUSE Wireless :: Slow Wireless After Upgrade To 11.4?

Mar 20, 2011

I have an Acer Aspire 5920G laptop, which uses Intel PRO/Wireless 3945ABG wireless card. I upgraded from 11.3 to 11.4 using live upgrade and after the upgrade wireless internet became really slow. Now I'm back to 11.3. I experienced the same problem with speed when I was choosing Linux distro - first I tried Fedora and Ubuntu and both had the same problem, but when I tried openSUSE 11.3 it worked fine. With 11.4 Network Manager showed that signal is at 100% and it connected to router with normal speed, but when I tried downloading a file I got 30kB/s max, while I used to get 1,1 MB/s with windows and 11.3. I also noticed that right after boot I got decent speed, but it only lasted for less than a couple of minutes.

Since 11.4 should have better or at least the same driver as 11.3, problem is probably with configuration, but I am using NetworkManager, so I have no idea what could be wrong.

View 5 Replies View Related

OpenSUSE :: Ant Build.xml Does Not Exist - Build Failed

Apr 19, 2011

Ant was installed in yast2 but will not run since build.xml was never created. How can this be fixed? I would like to run AudioTool.

View 5 Replies View Related

OpenSUSE Install :: Install Some Wireless Drivers - Don't Have A /lib/modules/<kernel>/build Directory

Dec 14, 2009

I'm trying to install some wireless drivers, but apparently I don't have a /lib/modules/<kernel>/build directory, which is causing the Makefile to throw an error. Is there a specific place I should point the Makefile at?

View 9 Replies View Related

Slackware :: Compiling A RT73 Module In Slack 64 13.1?

Sep 27, 2010

Actually, I have posted this problem here but I don�t know if is best to ask it here. The problem is that I have upgraded my OS to Slackware 13.1 64 bits, and now, I can�t compile the module RT73 from serialmonkey

There are a lot of similar tutorials explaining the steps for a succesfully installation. I had followed any of them before, and I had no problem never.

But now, I get this error:

Code:
make[1]:Entering directory "/usr/src/linux-2.6.33.4"
Building modules, stage 2
MODPOST 0 modules
make [1]: Leaving directory "/usr/src/linux-2.6.33.4"
rt73.ko failed to build!
make:*** [module] Error 1
On the other hand, in the serialmonkey page they said that the driver was included into the kernel yet, but I don�t know how can I now if I have the driver installed. The true is that my usb doesn�t work.

It�s is a USB D-Link System AirPlus G DWL-G122 Wireless Adapter (rec.C1) [Ralink RT73]

View 4 Replies View Related

Debian Configuration :: WiFi Rt73 Won't Connect To Network?

May 20, 2011

I bought a USB wireless adapter for my desktop. I finally got it to partially work using firmware-ralink as described [URL]sing network manager it will pick up my wireless network. However it will not connect to it.

The output of iwconfig is
wlan0IEEE 802.11bg ESSID:"familyfarm"
Mode:Managed Frequency:2.437 GHz Access Point: 00:1C:DF:B6:EA:B9

[code]...

View 5 Replies View Related

Fedora Networking :: Edimax RT73 USB Recognized But Not Working?

Feb 17, 2009

I have just installed Fedora 10 on a Dell Inspiron 530. I was delighted to see on the very first boot into the system that my Edimax RT73 USB stick was recognised by the system as it was offering a selection of wireless networks to connect to. But oddly, my own network wasn't listed there. I created a new network and entered the network id manually. Once it was in the list, I checked the radio button and saw a message that I am connected to my network. But after a few seconds the network icon disappeared.

I rebooted the system and again went through the same process with the icon disappearing.

I have an Edimax wireless access point with DHCP enabled. The security is WPA2 Personal with AES.

Vista is also dual booting on the same machine and working fine.

View 6 Replies View Related

OpenSUSE Install :: Build A Multiseat System (Build A Six-headed Six-user System LG #124)

Oct 1, 2010

I am trying to build a multiseat linux system(Build a Six-headed, Six-user Linux System LG #124). I am posting some outputs output of lspci | grep VGA

Code:
00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2)
02:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 8400 GS] (rev a1)
ls /dev/input/mouse*
Code:
/dev/input/mouse0 /dev/input/mouse1 /dev/input/mouse2
more /proc/bus/input/devices

[Code]...

I am having trouble in configuring xorg.conf. I am running Suse 11.3 desktop on my PC. Also, I have one onboard nvidia graphics 6150SE and I have put one nvidia 8400GS 512Mb in the 16X PCIe slot for the additional seat...

So kindly tell me what should I do now or what things are missing ?? For any further info abt my PC plz tell me to post outputs(specify the commands for the same..)

View 11 Replies View Related

OpenSUSE :: Unable To Upgrade Applications In 11.4

Apr 4, 2011

I was anxious to update my Opensuse to 11.4 but was worried about my slow internet connection. However an user of this forum kindly sent me a DVD by mail wich enabled me to do what I wanted. I just finished making a fresh install of Opensuse 11.4. It's wonderful. Almost all applications have improved a lot. But, unhappily some few have acquired new problems now, specially some that are in repos but not in the DVD. Let me number those I have found:

1 - In all versions of Gnome ctrl+alt+arrow (left or right) was the shorcut to switch between workspaces. Now it doesn't work. When I go to keyboard shortcuts in Gnome all options in the section of desktop enviroment are written "unknown action". There is no place to create shortcuts for actions related to the desktop as switching between workspaces. (I also want to use the opportunity to ask how can I create a shortcut to switch between workspaces in KDE too.)

2 - I used Qsynth/Fluidsynth as the default output synth for Rosegarden in Opensuse 11.3. In all versions Fluidsynth recognized bank variations immediatily and automatically as I changed them in Rosegarden. Now I installed the latest versions from Opensuse download site and it doesn't recognize bank variations anymore. It only recognize presets of the first bank of my soundfont. Strangely, in Fluidsynth-dsii I can load presets of any bank. But Qsynth/Fluidsynth doesn't recognize them.

3 - Nvidia proprietary drviers always used to cause some minor problems with compiz. But now they are worst than ever! When I launch applications most of the times windows come maximized but on the screen they are not really maximized at all. I have to click on the window title to bring it to the right size. If I don't do it letters inside that window don't appear correctly. Sometimes I click in close button in a window and it only works after the 2nd or 3rd click. And there are another some minor flaws or slowdowns.

4 - In a terminal I typed su. As superuser I typed nautilus. It didn't launch and gave me back the following message:

GLib-GIO:ERROR:gdbusconnection.c:2279:initable_init: assertion failed: (connection->initialization_error == NULL)

I just can launch nautilus if I login as root.If anyone have tried to connect Opensuse 11.4 to internet using DSL and it complained about one or more missing files and you didn't find those files in neither in DVD nor in 11.4 repos, it really has happenned (at until last week if anyone didn't correct it yet). The workaround is to download them from 11.3 repos and install them manually using Yast. It really works!

View 9 Replies View Related

OpenSUSE :: Unable To Use Emacs After Upgrade From 11.3 To 11.4?

Apr 5, 2011

I'm using emacs as editor. When using Emacs with any kernel for the 11.4 version, I observe that the cursor does not follow the arrow keys, and that some characters are randomly appearing in the Emacs text windows. This disappears when using the failsafe kernel. What could be the origin of this flaw and what can be done for solving this issue ?

View 1 Replies View Related

OpenSUSE Wireless :: No Connection After Upgrade

Dec 18, 2009

I've got an old Compaq Armada E500 laptop (850mhz PIII, 512mb RAM, 30GB HD) that I've been running OpenSUSE 11.1 w/Gnome desktop. My wireless adapter (Linksys Wireless-G, model WPC54G ver. 2 w/acx-111 chipset) worked well with this setup, but no that I've upgraded to OpenSUSE 11.2 w/KDE, I've got to start all over. I tried doing what I did before, which was to copy the firmware file into /lib/firmware.

View 9 Replies View Related

OpenSUSE Wireless :: How To Get AP Back After The 2.6.27.42 Upgrade

Jan 15, 2010

I ran the update last night and my Access Point died!It seems that the update has renamed my wireless interface from wlan0 to ath0.I also noted that the wlan0.mon and wireless.mon interfaces are not there any more? I may not have exactly the right names - 'cos there not there to check! I'll change hostapd.conf (interface=ath0) to reflect the new interface name. what else I must do to get my AP back after the 2.6.27.42 upgrade?

View 9 Replies View Related

OpenSUSE Install :: Unable To Use Keyboard After Upgrade To 11.4?

Mar 16, 2011

A few days ago I upgraded my workstation from OpenSuse 11.2 to 11.4 and found that when I got to an X login screen I could not type anything though the mouse worked. If I went straight to a terminal, such as by booting to runlevel 3 the keyboard worked fine so I figured the problem was related to Xorg. I did some research on the web and tried various fixes, such as reloading the proprietary Nvidia drivers, trying the nouveau drivers, booting with the nomodeset option, as well as trying most of the suggestions in this excellent article: SDB:Configuring graphics cards - openSUSE. No of these solutions remedied the problem.

Eventually I looked closer into the new (at least compared to 11.2) configuration for xorg. If I used the xorg.conf.install file or used an earlier Nvidia-specific xorg.conf file the problem continued. After taking a closer look at /etc/X11/xorg.conf.d/90-keytable.conf file I noticed all of the values for the options were blank, just "". I set XkbLayout to "us", started X and I had a functioning keyboard!

View 1 Replies View Related

OpenSUSE Install :: Unable To Mount Drives After Upgrade

Jan 10, 2011

I just upgraded from 11.2 to 11.3, everything seems to be working fine except that my other hard disk partitions are un mountable as my normal user. I used to be able to click on the drive in Dolphin and it would ask for the root password to mount it, but now it gives the error that the action is denied by org.freedesktop.hal.storage.mount-fixed auth_admin_keep_always <-- (action, result) What do I do to fixed this? I have checked as many settings as I can and can't find it. I would like to avoid editing the Policykit.conf file manually if possible (if that even is the right file).

View 6 Replies View Related

Ubuntu Installation :: Build An Upgrade CD With Apt-get?

Jun 16, 2011

Using Ubuntu Server 10.04 LTS. I have only command-line on this. I have limited band-width were box is located. After a fresh install I'll want to update the install. Is there a way to after the inital install to get a file or script file of everything it wants to upgrade with all dependencies, take may laptop with this info to another high-bandwidth location get the pacakges burned to a CD, then return to the server and tell it to update from the CD.

After that's done I could update as usual, it's that first update that's usually the big one.

View 1 Replies View Related

OpenSUSE Install :: Upgrade From 11.1 To 11.2 - Wireless Card Configuration

Dec 1, 2009

I've got an old Compaq Armada laptop (850 mhz PIII processor, 512mb RAM, 30GB HD, DVD ROM) that I've been running OpenSUSE 11.1 on in a dual boot configuration with WinXP for almost a year. I've downloaded and burned a LiveCD of OpenSUSE 11.2 and booted the computer with it. Very impressive. I want to install it on the HD without doing a clean install. That is, I want to replace 11.1 and keep the WinXP partition intact. My biggest trepidation is getting the wireless card configured again. It was a bear the first time. Is there a way to update OpenSUSE without losing those settings?

View 9 Replies View Related

OpenSUSE Wireless :: No Change After Kernel Upgrade For Betterment?

Jan 7, 2010

This is my first post here. I'm using Opensuse 11.2 (Gnome)and the inbuilt kernel is 2.6.31.xx. My laptop is having bcm4312 (14e4 : 4315 id)chipset for wireless. (0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) 0e:00.0 0280: 14e4:4315 (rev 01) ) I have read multiple times here in some threads that this kernel will require Broadcom-wl drivers(Tried ,No success with this) And If I want to use b43 drivers , then I need to go for the 2.6.32 kernel (stable one from this release). I've done the same exactly given in some other link -

Steps-
make mrproper
make menuconfig
make dep
make clean
make bzImage
make modules
make modules_install

After rebooting it's not showing anything new.Just the boot menu with the older one. Experts, Kindly let me know what I'm missing?

View 6 Replies View Related

OpenSUSE Install :: 11.2 Recent Upgrade Unable To Input At Login

Jan 9, 2010

I just recently updated to openSUSE 11.2, but after restarting my computer, I was unable to do anything with the keyboard(type my password, CAPS LOCK, Ctrl+Alt+Backspace) or move the pointer with my wireless mouse. After restarting the computer again, I turned on the touchpad of my laptop and was able to move the pointer using the built-in touchpad. After yet a 3rd restart, I could not move my pointer using any method.

After a 4th restart, I chose to enter the failsafe mode, where I could attempt to find the problem from the command line. I manually started KDM as root by typing in "kdm", but nothing happened, which means that the screen did not switch into graphical mode, but the terminal only accepted the command. Then, I manually started X as root by typing in "X", and X started. I only saw a black screen, but I could not kill X by the traditional "Ctrl+Alt+Backspace" and was forced to shutdown my computer via the power button.

I do want to note that on every boot of my machine, "WARNING" messages have begun appearing, but they went so fast that I could not read them. If there is any way to read them, I would greatly appreciate knowing. Also when updating my machine, I remember ignoring some dependencies for kernel-extra, kdm-branding, sox, and gcc44-fortran; but I did not believe that ignoring these dependencies could cause a broken system so I proceeded with the upgrade.

View 8 Replies View Related

OpenSUSE Wireless :: Unable To Set Up Ad-hoc Network

Oct 5, 2010

I'm using OpenSUSE 11.3 64-bit on a Lenovo G560. I'm able to establish both wired and unwired connections without problems. Now I'm in a situation where I'd like to share my laptop's internet connection with other devices. My thought was to establish an ad-hoc network that another computer could connect to wirelessly in order to get into the Internet, because I've only got one ethernet jack.

First thought was to use Network Manager, since that manages all my connections. A left click on the Network Manager icon brings up a menu in which "Wireless 802.11, Create network connection..." is an option. If I click on that I see a list of all the networks available in the area, as well as all the networks I've set up in the past. Below that are two options: "New Ad-Hoc Network" and "Connect To Other Network With Wireless 802.11..."

"New Ad-Hoc Network" seems like the right option, but when I double click on it the window closes and nothing happens. No error message, nothing. Network Manager continues to run and my connection is unchanged. If I just left click on it and then click "Connect" at the bottom of the window, the same thing happens.

View 9 Replies View Related

Software :: Build Samba From Source And UPGRADE It Easily?

Jan 6, 2010

Now that we are starting to face the reality of Vista/Win7 implementations, we will need to do an upgrade of Samba to enable functionality. I am having difficulty in upgrading our version of Samba (3.3.4), as I compile from source, and do not use binary distributions. I'm running Slack12 and could really use some help on how I can build samba from source and UPGRADE it easily?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved