I am using OpenSUSE 11.2. Knetworkmanager seems to connect to AP with the highest signal most of the times(even after choosing others from the scan list). But I want to connect to another AP which has a lower signal but lesser number of users. how to ALWAYS connect to a specific AP(I know the address of the AP) using the command line or some other method.
View 2 RepliesMy wireless is a libertas 88w8335. Suse 11.4 just installed. For this one, I need a windows driver with ndiswrapper. ndiswrapper is installed, and the driver as well.
I can see my networks with iwlist scan my network is set up in yast with ifup (I can scan the networks and find mine), but I cannot connect to my Acces point : there is no SSID with iwconfig.
I have a complicated situation due to my goals and network structure. I have in mind a potential solution, a bridge, but I do not know whether it is feasible or what hardware it will require.
The network:
My apartment community provides residents with free Internet access through an ancient T1 line. We do not have the option of other Internet providers, so having a router and modem in the home are not an option. The T1 line is split among some 24 switches, one for each building, and each switch has one port per floor. At each floor, there is a D-link WAP, and each has a separate SSID and WEP key. Additionally, they control access at the switch level using Access Control.
My goals:
I'm used to being in control of my networked environment. I like to have friends over often, and most of them have a laptop, a smart phone, or both, which makes Access Control a pain. I don't want to have to think ahead and get their MAC addresses to the IT consultant while he's here during business hours. My wife and I have 6 devices, two of which require an Ethernet connection.
I use a few applications for streaming that utilize UDP (I'm not sure if the WAPs are smart enough to even handle this) and I don't like having my traffic muddled with my neighbors.
I should note that I tried extending the network with my Airport Extreme router, which apparently only works with other Apple devices. I've also looked into WDS, but that seems to require an unlikely amount of cooperation from the IT consultant on site.
The potential solution: a Linux server that acts as a router. Ideally, it could act as a webserver for a small static site as well, but let's focus on the routing. I'd like to bridge two NICs and use masquerading (Internet Connection Sharing). The public interface would connect to the WAP using WEP. The private interface would allow up to 8 devices to connect to the server.
It seems easy enough to configure the public interface, and even to bridge the connections. What I've never done before is purchase a wireless card that can accept multiple clients. Maybe they can all do this?
i've finish install driver for my wireless adapter and the result like this:
Code:
rapc0d@rapc0d-laptop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[Code].....
I just installed the wicd network manager and when i was setting it up it said it couldn't find the ip address so when i input the address its saying it can't connect to a wireless access point. I am using wireless that has worked with the default network manager but will not work with this one.
View 1 Replies View RelatedI installed it alongside Win XP, using Wubi, and it seems I use Ubuntu 10.04.Everything worked out as expected, and my wired internet connection works like a dream.However:My wireless connection seem a little buggy.I can see all networks (except WPA2) so even if I want to fix the WPA2 problem, I'd rather just open my network for now.
So my network is now open, I see it in the NetworkManager list, and as i try to connect, the following happens:The wireless symbol start flashing. From here it keeps flashing, untill it gives up.I use RT2870 drivers, and D-Link DWA-140 USB wireless adapter.
It goes without saying I am a freshman regarding Linux, so if anyone knows what to do, and cares to take the time to tell me, please do tell me in a detailed manner.I do know the basics of the Terminal, and yes, I do know how to copy/paste commands I find linux way more satisfying than Windows so far ... And thanks in advance for giving away your time More info can be given upon request (You might have to explain how to find that specific info)
I have an Intel PRO 2200BG wireless card and can connect to my router when logging in via gdm (using Xubuntu.) No problems there, connection never drops, very reliable!
But I've since had the need to shutdown X and keep a simple terminal instance open but as soon as I stop gdm the connection to the router drops. Trying to connect via the terminal using wpa_supplicant has so far been unsuccessful.
I know for a fact I'm doing something wrong, just don't know what and would appreciate some help!
Some dumps:
Code:
Code:
Code:
Code:
I am quite new in Linux and start trying by using Fedora. I installed Fedora 10 on an old PC. I installed once and Fedora 10 recognized my wireless USB finger. Well after some setting but I cannot recall teh exact details. Due to certain reasons, I have to re-install Fedora 10. However, this time the wireless device is not working (The system recognized it and the driver is working ok but not able to connect to the access point and I caanot find a place to check the available wireless network list. I used WEP password protection so need to see the network list and select the network for prompt of the password entry.)
View 1 Replies View Related10.04 in a couple of identical lenovo laptops (of friends) suddenly have stopped connecting successfully to wireless, coinciding approximately with a mains power socket fail at the modem router, now fixed. presumably the machines were trying to connect to the access point, which may or may not have been working, but themodem router was not. Now, internet connection and wireless access point is fixed ok and is back up, and i can connect wirelessly to the access point ok using an eeepc with 10.04.2 with no problem so the access point is working ok
the target laptop/s are still ok via wired ethernet, and can *also* connect to a neighbours open wireless (a british telecom so called fon network, it asks for an account password), and all local wireless networks can be seen normally, and the home access point ssid can also be seen ok. so the aptop wireless is connecting ok, but not to this particular access point now. maybe someting has got screwed up? it is wpa2 and when clicked, after a long-ish time, the authentication is requested, then given, correctly, and still not connecting, asks for authentication again etc etc. no local secure wallet is being used.
when upgrading these laptops for my friend some time ago from 9.04 i have a small recall that 10.04 had a odd thing with wireless authentication (?) bug? i have deleted the network connections gui listing for this ssid and restarted the laptop, still no joy.
I'm able to configure my Wireless network to connect with an AP with WEP key but...
Now I'm at home, I've a WPA2 key (my router now is supporting both, WPA and WPA2). I used WICD to connect but no success at all! It just stops with "Connection failed: Could not contact the wireless access point"
if I type IWLIST key:
Code:
ra0 2 key sizes: 40, 104bits
4 keys available
[1]: off
[2]: off
[3]: off
[4]: off
code....
I decided to change my DSL internet connection to cable and WiFi. So far so good, and under Windows, the system is very well working.
I use openSuse 11.1 but I can't establish contact between my computer and the new Wireless N acces point.
I have a Ralink network card, which functions under Windows.
/usr/bin/lsusb gives this result : bus 001 device 006 ID 148f:2573 Ralink Technology, Corp. RT2501 Wireless adapter
dmesg | less gives (amongst others !) - so my card is recognized :
usb 1-1.2: configuration #1 chosen from 1 choice
usb 1-1.2: New USB device found, idVendor=148f, idProduct=2573
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[Code]....
The wireless access point I bought from the cable company is a D-Link Model DIR-615 which should be capable of IEEE 802.11 b/g/n. I have its MAC ID.
When in YAST, I want to make my computer hook on to my D-Link router (my new access point), I go to YAST Manage Network Wireless and I want to fill in BSSID, I get stuck.
Running OpenSuSE 11.2 32 bit dual boot with XP. 3Com OfficeConnect Wireless 11g USB dongle connects and works happily in XP. Can not get it to associate with the same AP in Linux.
Device identified as:
Device 3CRUSB10075 wlan0
Driver zd1211rw
Appears to be installed, to the extent that it sees the broadcast SSID. Output of /usr/sbin/iwlist scan correctly identifies the ESSID and encryption (disabled) More particularly, /usr/sbin/iwconfig outputs that the "Access Point: Not-Associated"
linux-tgb6:~ # /usr/sbin/iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[code].....
Debian 2.6.32-5-amd64 KDE I have to make one of my computers wireless. i need some product recommendations for a wireless access point & a wireless network card.
View 4 Replies View Relatedone of these "WiFi works in Gnome, not in KDE" threads, but I have been all over google and hundreds of threads across different sites and can't figure this one out.As mentioned, wireless is peachy in Gnome, unfortunately I like KDE and I'm more productive using it (when I have internet). Wired network works fine in KDE, and my network card
Code:
03:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
Subsystem: Intel Corporation Device 1201
[code]....
I have done the follow steps.
sudo ifconfig wlan0 up
sudo iwlist wlan0 scan (I see my access point without problem)
then...
sudo iwconfig wlan0 essid MY_ESSID key s:MY_PASSWORD
I get the follow error:
Error for wireless request "Set
Encode" (8B2A) :
SET failed on device wlan0 ; Invalid argument.
I used s: because I want to pass and ASCII password.
Install Fedora 12 on my laptop and having problem connecting to access point using WEP . I complied with wireless setup with key but will not connect. Works with security disable, the router is a Westell 327W from what was Bellsouth.
View 1 Replies View RelatedSo theres this project I'm going to try working on during my free time and part of it includes using a wireless NIC as an access point. The way I see it, if a wireless NIC can send and receive wireless signals to a wireless router/WAP, why can't it be treated like one as a router/WAP? A router is a specialized computer after all.From what I heard this idea is possible but I'm having trouble finding results, since search engines don't know exactly what I'm talking about. Does anybody have any idea how I can accomplish this?
View 5 Replies View RelatedI am trying to make my computer an access point for a PS3 to connect to directly. I'm not too bothered about it behaving as a router, just a direct connection would be sufficient. I have installed hostapd from slackbuilds.org and followed the guide given at [URL]. Hostapd seems to work ok - it creates a new interface called mon.wlan0 and I can see the access point from my netbook but I can't connect to it. I think the problem is with dhcpd. Here's my /etc/dhcpd.conf:
[Code].....
OK, what I want to do, I think is possible but I dont kno name of it or how 2 do it under even windows for that matter. I have my current PC connected via Ethernet directly to my house router. Now on this Motherboard, I also have a wireless nic that I have no plans on usin. Can I turn it in2 an access point/wifi for other devices like iPods, Wii, Labtops, ect?Also, how would I do it if not Wifi, use the other Ethernet port to plug up say a labtop. In which the labtop uses the net I am getting from the router?
View 1 Replies View Relatedi ahve just installed fedora 11 kde edition and i used to use fedora 10 after finish installation i edit the connectons to connect to my network im in lan network but i connect my cable to an access point to free using my laptop anywhere after adding every thing (wep key ,static ip's,) as i used to do and i have the connected sign at the system tray.i open the browser but no internet connection pinging the gateway returns "Destination Host Unreachable".
View 1 Replies View RelatedI am looking for help on how to create a wireless access point using fedora core 12.I have done some searching and have not found anything.
View 1 Replies View RelatedI have a laptop with Fedora installed and an iPad.The only connection to internet in my house is wireless router. It has strong signal to catch it with laptop in every corner in my house, but not strong enough for an iPad..Since my iPad is mostly near my laptop, I'd like make my laptop to be turned to wireless repeater or that serves as access point so I can connect to network with an iPad.How can I do that from my Fedora machine?
View 1 Replies View RelatedI have a Sonicwall access point, which I am able to set up through the interface, but after that I am unable to achieve a connection through my wireless card. I have a good understanding of everything involved, but really have no hands on experience when it comes to networking.
Code:
lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 735 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
[code]....
Also, I should have mentioned that @ the interface for the Sonicwall it said that "no DNS server had been specified", but I set it up for DHCP, and I thought my ISP is using PPPoE (which I also thought used DHCP).
I'm trying to set up a wireless access point and router using Ubuntu 10.10. My machine has an Atheros AR5001X+ PCI card, and eth0 is connected to an ADSL modem.After literally days and days of going in circles, I'm hoping that somebody here can help get me on track.This sort of works, though I had to go through some other contortions to get the madwifi driver to finally compile on my machine.At this point, I can see and connect to the WAP, but nothing more. When I try "sudo /etc/init.d/networking restart",
I also have a second problem, which is that I want to use WebMin to manage this server, but I cannot figure out how to get the ADSL client module configured -- RP-PPPoE version 3. It seems to expect to work with pppoe-start, pppoe-stop, and pppoe-status, but when I try to run pppoe-status it says "Link is down", even though my ppp connection is actually working.Is is possible to use the WebMin ADSL client module with Ubuntu? I spent a lot of time trying to get pppoe-start, stop, etc. working but it was a complete mess and never seemed to behave. Finally, I just put the ppp startup commands into the /etc/network/interfaces file and that worked, but now the pppoe-* commands no longer seem to function.
I'm going to be working in an office with no wifi and no 3g signal but my laptop will be connected to the web via a wired network.Any way I can use the wifi card in my ubuntu laptop to create a wireless access point so my phone can connect? Would have to be easily selected and deselected as I'd then want to use wifi to connect to the internet at home.
View 1 Replies View RelatedI started using Arch just a few days ago. forward traffic to the Wireless access point I created on arch. i am using cable internet (ppp0) which I want to share via a usb wifi adapter running as a WAP. I followed the instructions in this link to enable the AP mode. Afterwards I followed the instructions provided in the Arch Wiki to forward the traffic but because of my inexperience I am still unable to connect to the internet. Here is the output of iptables -nvL :
Code:
Chain INPUT (policy DROP 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
77 31312 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0
0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID
[code]....
i'm running slack 13.37. my machine has a "generic" wireless card which is currently sitting idle in it, since i used a wired interface for internet and local networking (i used the wireless interface for a while, but for what i need it wasn't a reliable or stable enough connection). my question is, can the idle card be used as a wireless access point on a separate subnet? if so how?
View 1 Replies View RelatedI just upgraded to 13.37, and for some reason wicd now cannot connect to my wireless point. It keeps saying the password is wrong, when I know for an absolute fact that it is correct (even changed the password to '1' just to make sure, and no dice. Which is weird because even though its the exact same version of wicd, and not only that, it no longer seems to be able to see networks with my built in card, so having to use a USB card. Anyway, googling turned up very little. Seems to be a common problem across distros, and some people reported that downgrading to 1.6.x fixes it.
So, I ran
Code:
removepkg wicd
And it uninstalled wicd. Downloaded wicd-1.6.2.1-x86_64-1.txz from a 13.0 mirror and did
Code:
installpkg wicd-1.6.2.1-x86_64-1.txz
While in the correct directory. It installed, and I ran wicd. But checking the version number when it loaded, it says its 1.7.0 again.
Not really sure why this happens. I'm assuming there's some remnant of wicd that removepkg doesn't dump, and its preventing me from installing this older version of wicd. What do I need to do for this? If anyone has a surefire way to make 1.7 work again, that would be fine.
My wireless is 'almost' working, but frustratingly not quite there. Debian Testing (squeeze). I have two different wireless adapters. Both work flawlessly from an ubuntu live CD in the same machine, connecting to the same unencrypted access point so the problem is not faulty hardware, weak signal, overpowering signal, interference from other AP's, MAC filtering, or anything to do with WPA.
I have loaded the correct (I think) firmware packages for both adapters. dmesg is not complaining about missing or incompatible firmware. I have googled the various error messages reported in dmesg and found that the /etc/Wireless/RT2860STA/RT2860STA.dat missing config file is normal. I could not find anything that I understood concerning the BSS returned, data->length messages but since I see the same thing in Ubuntu (where the wireless is working flawlessly) I assume they are also normal and not related to the problem.
Both adapters can see all the available access points (using iwlist {iface} scan or using gui tools such as wicd, wifi-radar) NEITHER adapter will associate with any access point (and I've tried three different unencrypted AP's so far). I can connect to all/any of these AP's from an ubuntu live CD using the exact same hardware, so this is NOTHING to do with MAC filtering, etc... using 'iwconfig {iface} essid' as root to set the essid "appears" to work, but simple does not set the ESSID on either wireless adapter.
Using the GUI tools (which are only a front end for the command line tools so I have no idea why everyone thinks a GUI front end like wicd will magically work where the command line tools don't!!) I simply wait a long time for "getting network address" before it eventually fails. LOTS of information in pastebin, please make the effort to read it before asking me for things I have already supplied. And please keep any "RTFM noob" or "go back to ubuntu" replies to yourself. I HAVE read the f*cking documentation and I do not want to go back to ubuntu. I just want to get my wireless working in debian.
I'm trying to make my F10 Laptop a wireless Access point.
When I 'iwconfig wlan1 mode Master' I get:
SET failed on wlan1; Invalide argument.
wlan1 is a Netgear WG111v2 which worked as soon as I plugged it in after I installed F10.
I don't know is it not supported? What is? Is there a different driver I can put on that will work in master mode.
What should I do basically?