OpenSUSE Network :: Wifi Master Mode Not Supported Using Yast?

Jun 2, 2010

after trying several pci and usb network cards none were able to have their ssid broadcasted. The question that i have is: Can a suse box be converted to act as an acces point without the use of atheros based hardware, without switching over to ubuntu and or debian, without the use of openwrt?

View 4 Replies


ADVERTISEMENT

OpenSUSE Wireless :: WiFi Printer Mode Off In Yast With Firewall

May 5, 2011

I have WiFi printer, HP DeskJet F4500. If suse firewall is on, yast doesn't see that printer. If I turn firewall off, Yast sees printer and install it just fine. Problem is, that when i start firawall again, yast denies whole printer and turn it off mode in Yast. What firewall rule i have to make to get this work?

View 2 Replies View Related

Ubuntu Networking :: Consulting Regarding Edimax Wifi-usb Supported Modes At Jaunty (master And Ad-hoc)?

Jan 25, 2010

After purchasing few wifi-usb-dongles for my jaunty and lost many hours, i had no success in bringing them to operate as master or ad-hoc.The devices were Belkin, Level1, and a TP-Link 620 Though the Belkin could work as ad-hoc, but very often disconnects due to buffers issue (though I couldn't build the zd1211b driver for jaunty and it seems that no one can really help with that).

Now I would like to consult with you ahead regarding new potential devices, whether you know it operates as master mode or ad-hoc mode under jaunty (9.04)?

My concerns are regarding:
1. Edimax EW-7318UG
2. Edimax EW-7318USg
3. Edimax EW-7711UMN
4. Edimax EW-7711UTN
5. Edimax EW-7311USN
6. Edimax EW-7717 nMax
7. Edimax EW-7718 nMax
[URL]..

View 1 Replies View Related

Hardware :: USB Wifi With Master Mode?

Jan 6, 2010

I'm looking for a USB wifi which supports master mode, 11n modulation, 5GHz band (with master and ad-hoc support for this band) and has detachable antenna connector.

View 1 Replies View Related

OpenSUSE Network :: Getting Yast DHCP Out Of Expert Mode?

Dec 22, 2010

I feel really dumb for asking this but I cant figure out how to get it back to simple mode

View 4 Replies View Related

Ubuntu Networking :: TP-Link Wifi USB Adapter: Cannot Setup It In Master Mode To Use PC As A Router

Jun 10, 2010

I got two issues with my wifi usb adapter:

1) it cannot see any networks around
2) i cannot setup it in master mode to use my PC as a router

As far as i can see, the device is recognized and the correct driver (rt73usb) is loaded. I was able to connect to a laptop somehow (the laptop could see other networks and the adapter's PC-to-PC network). I'd like to make it work as a router, i.e. share my internet connection (eth0) via wlan0. Here is what i have:

Code:
Ubuntu 10.04
Linux 2.6.32-22-generic #36-Ubuntu SMP Thu Jun 3 19:31:57 UTC 2010 x86_64 GNU/Linux
TP-Link TL-WN321G wifi usb adapter as seen as
Bus 001 Device 006: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
$ iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
[Code]....

View 4 Replies View Related

OpenSUSE :: 11.1 - Installing WiFi Internet Access (YAST Disappeared)?

Sep 26, 2010

I use openSUSE 11.1 since quite a bit and I frequently use YAST (not as root of course). However, since the problems I have to deal with while trying to install WiFi internet access I meet the following problem. I call YAST, get the small authentication screen, I give the right password, which seems to be recognized as such, but I never see YAST appearing. So I can't manage neither my hardware, nor my software.

View 9 Replies View Related

OpenSUSE Network :: Device YaST - Can't Identify YaST - "Unknown Network Device"

Dec 8, 2010

In my YaST Network Settings (11.3), I see an entry labelled "Unknown Network Device" how to remove the confusion? The Overview tab also correctly lists my three known network devices (listed below), as does the Hardware Information utility. This is the output of lspci, and as far as I can tell, is accurate and complete. So what has YaST seen that it can't identify?

Code:
00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 11)
00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 11)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI [Code].....

View 7 Replies View Related

OpenSUSE Wireless :: Edimax WiFi Cards Is Supported?

Mar 14, 2011

which chipsets are on the PCi and PCie cards, EW7722in and EW-7612PIn, and whether they can be made to run on a linux system. My system is recent (Linux home 2.6.37.2-0.6-default kernel) Do they have the same chipset as EW-7711In, which I notice has explicit linux support? Now this was on the 3/03/2011, and I had given up getting any kind of useful support, but I got a reply today. I hope they wont mind if I quote them:

[Code]...

View 4 Replies View Related

OpenSUSE Network :: Configure A Connection With YAST As Well As With Network Manager?

Feb 1, 2010

Im new in this world of linux and suse. I have just installed the opensuse 11.2 in a Dell Inspiron 5160. Such laptop has a BCM4306 Wireless LAN controller. When I tried to configure a wlan connection, I found that the firmware was not installed. After looking in different forums, I installed the firmware b43. Now, my wlan card is abled to find the wireless of my router.

I have tried to configure a connection with YAST as well as with Network Manager, but both cases failled. Specifically, when I use Network manager, Im able to see in the applet my connection, how strong is the signal, but I see a yellow symbol (in one forum, such a box is shown with a green symbol).

I have check many time all about the secutity, encryption, and so one and all seems to be correct. But when I open the mozila firefox or the konqueror browser, no chance to surffer in internet. Now Im just a step to become crazy. The drivers are ok, the information about the router and the keys are ok, but in such a way, I am still harmloss.

View 1 Replies View Related

OpenSUSE Hardware :: Error - Kernel: [time] Sisfb: Mode 'none' Not Supported Anymore. Using Default

Aug 7, 2010

I have just upgraded to 11.3 and work in icewm (I have kde apps installed but no other desktops). When I boot up the computer it gives me this console error message:

Code:
kernel: [time] sisfb: Mode 'none' not supported anymore. Using default.
kernel: [time] sisfb: Fatal error: Unable to reserve 16MB framebuffer memory
kernel: [time] sisfb: Is there another framebuffer driver active?
Apart from that I'm not exactly sure what the problem is. The computer isn't displaying immediate symptoms to me. I checked the hardware sticky and when I have a few hours I can work through

HTML Code:
http://en.opensuse.org/SDB:Configuring_graphics_cards but I don't have that kind of time at the moment, so I wanted to check that that was the route I should be going down before I did. I googled this stuff but everything seems to start from a knowledge base above mine and leaves me clueless.

View 6 Replies View Related

OpenSUSE Network :: 11.2 Install - When Exit YaST The Network Doest Show Up - No Icon In The System Tray And Doesn't Even Try To Connect

Jan 16, 2010

I am relatively new at Linux and am having some problems with an install of openSUSE 11.2. I installed 11.2 on my Thinkpad X31 dual boot with WinXP. It seems to work very well except the network. I looked up swerdna's instructions on setting network cards up. I used YaST to try and set the system up as described in swerdna's instructions. Everything looks fine my network card and wireless card show up in the overview settings screen and everything sets up fine. But when I exit YaST the network doest show up no icon in the system tray and it doesn't even try to connect.

I did go into hardware to see if it was identifying my hardware and my network card shows up as "Thinkpad R40" and the wireless shows up as Cisco Aironet Wireless 802.11b. As far as I know this is correct. I have tried three other distro's and this one has gotten the closest to working so far.

View 8 Replies View Related

OpenSUSE Network :: Using Yast / Ifup Instead Of Network Manager?

May 27, 2010

How do you mannually set up a network using Yast/ifup? I'm trying to get my wireless running on a Broadcom 1390 WLAN. I've gone through the stickies in the wireless forum (this is my first stab at Linux) and have gotten the drivers installed and the internet working (albeit intermittently) using Knetwork manager. It seems that some folks that have had the same issue did not have problems setting the network up manually with Yast & ifup. I've disabled network manager in Yast, and I went through man ifup. It seems I need a "pre-configured interface," but I don't know how to make that happen.

View 9 Replies View Related

OpenSUSE :: Yast Unable To Restart Network?

Dec 9, 2010

When I change something in network setings using yast (for example hostname) it failes to restart the network. I have to start knetworkmanager manually from the terminal. Does anyone get the same type of behaviour ? I'm attaching the relevant yast log.I'm using 11.3 KDE 4.5.4 2.6.34.7-0.5-desktop kernel.

Code:
2010-12-08 07:06:17 <1> opensusetest(6010) [YCP] network/runtime.ycp:28 Running SuSEconfig ...

[code]....

View 9 Replies View Related

OpenSUSE Network :: Set Up Dial Up Modem Using Yast

Jun 28, 2010

I have a US Robotics serial modem, and I have smpppd enabled in system services, with wvdial and kppp installed. When I try to set the modem up using yast, I keep getting hung up by the different screens. First a screen that asks if I need to dial a number to get out. I have to dial 9, so I have that entered. Then a screen that asks for "country" and "provider."

When I try to enter anything, nothing shows in the boxes, so I go to a screen that asks for the phone number, provider, user name and password. When I enter those, it goes to a screen that wants "Connection Parameters", with default settings and the "buttons" at the bottom of the screen "muted," or flattened out, i.e. unusable. That makes it impossible for me to set the information as saved, so it's back to the beginning and sart over, with the same results over and over. How do I get the modem so it dials out?

View 9 Replies View Related

OpenSUSE Network :: Connect To DSL Using YAST Manually?

Aug 23, 2010

I have installed 11.3. Now for DSL I use PPP over Ethernet. I have configured DSL via YAST and it works fine. The connection is set at boot.

Now I want DSL to connect manually not at boot time. I did changes in the YAST/DSL to start Manual and rebooted. Once rebooted how do I connect?? Like any button/applet ??

View 1 Replies View Related

OpenSUSE Network :: How To Configure YaST Firewall

Mar 5, 2011

I'm looking forward to the release of openSUSE 11.4, which I'm looking to install as an Internet facing gateway on a mini-ITX machine with 2 Ethernet cards. As such I've been reading up on the YaST Firewall trying to find out to configure it, and there's one thing I'd like to be able to do: 'stealth' all the firewall ports.

In other words, if someone were to hypothetically do a port scan of my external IP address, I would rather they not know whether any of the ports on my gateway are open or closed, so instead of replying with the status of those ports the packets get dropped. I've been able to do this with a product called Astaro Security Gateway, which I currently have installed on a second hand Dell Optiplex machine, but I am now looking into the possibility of installing this as a virtual machine inside an openSUSE 11.4 host (extra level of security) and would like the same functionality for the host OS.

View 9 Replies View Related

OpenSUSE Network :: Yast Won't Set DNS Servers / Resolve It?

Apr 29, 2011

When I set my DNS servers via Yast>Network Devices>Network Settings>Hostname DNS it accepts the addresses, but then when I check then the next time they are faded out. I set them again, but same results.

View 6 Replies View Related

OpenSUSE Network :: Kerberos + LDAP With YaST?

May 26, 2011

In the OpenSUSE documentation I red this very exciting chapter Chapter 6. Network Authentication with Kerberos That mentions "Using LDAP and Kerberos" which combined with NFSv4 would give my office net functionality of a M$ Win network.

We are still on 11.2 (we have no win clients at all) and I was testing different setups of 11.4 in VM, but I can't get YaST to configure the LDAP with Kerberos setup (our current setup does not use Kerberos only LDAP). Unfortunately I could not find any meaningful HOWTO on how to do it in SuSE. The page in docs involves editing config files, but I would like to avoid this, because from my former experience with Samba, as it would mean I cannot use yast anymore and that is sad.

Is there a way to configure LDAP + Kerberos (in terms of issuing of krb tickets at login) with YaST?

PS: I basically need Kerberos for NFS and Intranet site.

View 5 Replies View Related

OpenSUSE Network :: Is LLA Supported By The 11.3

Feb 4, 2011

anyone know if LLA is supported by openSUSE 11.3?

View 8 Replies View Related

OpenSUSE Network :: Configure YAST To Work With A Proxy?

Mar 14, 2009

I work with a proxy serverWhen i try to update my system i am not being allowed access. it tells me that i am denied access. what can i do?

View 7 Replies View Related

OpenSUSE Network :: Using OpenLDAP With Yast Configure Tool

May 9, 2009

I am new to using OpenLDAP on OpenSUSE with the yast configure tool. I have used Openldap on Fedora before and there was a slapd.conf file that I could modify. It appears that the yast does something different. Anyway I need to find out what the rootdn password is, but I cannot find it since there is no slapd.conf file.

View 2 Replies View Related

OpenSUSE Network :: YaST Package Manager Wants IPv6?

Apr 12, 2010

it's a couple of weeks I can't perform YaST updates from my openSUSE 11.2. The reason is that YaST wants to connect to repositories "only" through IPv6, but my network doesn't support it. I quoted only because I suppose it prefers v6 over v4, but it keeps trying to connect without switching to v4 or returning error.

Even if I disabled IPv6 from YaST/Networking/Network Settings, I still have a local scope address. I connect to Wifi using KNetworkManager. The TCP/IP stack should know that if an interface has a local scope v6 address and a global v4 address, it's a bad idea to keep trying with v6. Italian mirror, garr.it, of openSUSE repository both has v4 and v6 addresses. If I try to ping opensuse.mirror.garr.it I ping v4, but if I try to telnet that host on port 80 it tries to connect to v6. Same if I try to connect with Firefox.

How to tell Linux that I don't have IPv6? I'm connecting from University of Naples wireless network. While unina has IPv6 via GARR's Teredo tunnel (2001:760::/32 as I remember), it doesn't reach students' network because DHCP server doesn't release IPv6, nor Zeroconf obtains one. I just would like to use classic IPv4 until, at least for now.

View 2 Replies View Related

OpenSUSE Network :: Yast Could Not Connect With HTTP Proxy

Apr 25, 2010

My box has to connect to internet using specified http proxy.I have set proxy in both kde control center and yast2 control center. They both tell me the proxy works fine. But when I really try to use yast2 to update my system, it report an error:

Code:
Failed to download ./repo/repoindex.xml from [URL]
History: - [AbstractCommand.cc:195] URI = [URL]

Even I try
Code:
export http_proxy=http://XXXX
yast in command line,the error still exist.

In debian apt-get and slackware slackpkg,my proxy works fine. So I am sure it is not my fault and maybe it is a bug of yast2.

View 7 Replies View Related

OpenSUSE Network :: Has The YaST Proxy Module Changed From 11.2 To 11.3

Sep 1, 2010

I'm currently running 11.2 and I configured Proxy settings in the YaST module. It seems that when I use a proxy I have problems updating. It can retrieve some files, but while getting others it fails. Furthermore, I can't establish a connection with the timeserver in the YaST -> NTP configuration module.

My question is if there have been changes from this version to 11.3 regarding the Proxy settings.

View 1 Replies View Related

OpenSUSE Wireless :: How To Change From Network Manger To Yast

Mar 24, 2010

I'm having a wireless issue (go figure) where I can't get to the internet, can get to my LAN just fine, but trying to ping anywhere on the net just gives me "network unavailable" message.One thing I've seen noted here time and again is people saying "Use Yast vs Network manager" when I go through the Yast Network Devices GUI it tells me it's using network manager, and I need to use ifup (if I want to use Yast), however I have no clue how to go about changing it from one to the other?

Currently I'm using hard-link to get all the updates and see if that will resolve my problems, but figured I'd learn how I'm supposed to switch it for the future.

View 5 Replies View Related

Fedora Networking :: How To Set Ath9k In Master Mode In F11

Apr 9, 2010

Anybody have any idea that how to set the ath9k in master mode in fedora 11. I am unable to set the same.
I am using the D-Link DWA556 card using the kernel built in ath9k.Find below the output I got while setting up it in master mode sudo iwconfig wlan0 mode master.Error for wireless request "Set Mode" (8B06):SET failed on device wlan0 ; Invalid argument.Does that mean that master mode is not supported?Also Want the information if there is any separate community or development group for ath9k development and download the source of same except linuxwireless.com.

View 1 Replies View Related

General :: 802.11n PCI/(USB Okay, Not Preferred) Card That Can Do AP/master Mode

May 19, 2011

I am looking for a 802.11n wireless card that Linux supports that can be dropped into AP/master mode.

I would prefer PCI, but USB would be tolerable, just not preferred.

View 2 Replies View Related

Ubuntu Networking :: Cannot Set Wireless Mode To Master

Aug 6, 2010

Code:
root@Atlantis:~# iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
root@Atlantis:~# iwconfig wlan1 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan1 ; Invalid argument.
All other modes except secondary work fine.

The wireless cards are both PCI, a Netgear WG311v1 and a Linksys WMP54Gv4.1, though I'm not sure which is which.

View 5 Replies View Related

OpenSUSE Hardware :: Accidentally Deleted Network From YAST - How To Get It Back

Apr 30, 2011

I deleted the card from my 'network settings' in YaST. How do I get it back?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved