abhishek:/ # sudo /usr/sbin/iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a Flags: bus master, fast devsel, latency 0, IRQ 23 Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
I am running SLED 11 and My Networkcard is Intel PRO/Wireless 5300. In short, it is not there anymore! I mean I was connected and everything and the next time I restarted It could not detect any wireless network. I deleted the wireless network card in hopes that the OS will automatically detect it on startup and set it right but NOPE. When I check the hardware information in YAST, it is listed there and it is also working under Windows.
i've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:
Code: zypper in broadcom-wl broadcom-wl-kmp-desktop So now, the networkmanager detects all the networks around, but i cannot (or i don't know
I can not install a driver for device EDUP WU2070. I have a disk with a driver for linux general. I don't know how to compile a makefile. My OS 11.3v doesn't see a device. But when I run in Live CD mode all drivers install automatically and my WI-FI device work properly.
I'm running OpenSuse 11.4 with kernel (184.108.40.206-1.2-desktop i686) and KDE 4.6.00 "release 6".When I first installed the system the KNetworkManager found my wireless network. After entering my details it suddenly couldn't find it any more and hasn't found it since (even after re-install). My network is definitely working. I did try and set it up with ifup but it still couldn't find any network. Unfortunately I don't know anything about networks even less about wireless ones. Many thanks in advance.
I find any wireless networks, except mine. Moreover, my wifi works, because I can surf with the university connection.But the network works, because I can connect to it both with Windows and with Ubuntu.I have a Broadcom 4321 like wireless network card, opensuse 11.4 and the default network manager.
I have a dwa-125 dlink wireless card which will not work. This is my first time using OpenSuse 11.2 (Well OpenSuse period). I had the same problem with Ubuntu 9.10 as well. If it will help the solution I used with Ubuntu is here: [ubuntu] Dlink DWA-125 Wireless Card Issue - Page 4 - Ubuntu Forums. I'd rather use OpenSuse than Ubuntu.
I can't get on the Internet at all not even through Ethernet. (It recognized my Ethernet hardware but doesn't connect.) I got the broadcom-wl drivers from Packman and installed those and it still was a no go. I tried to get the drivers straight from Broadcom and those didn't work. I couldn't compile the source code from the Brodcom site because i could not get build installed (got make installed but build just didn't install.)
Card BCM4322 When I enter /sbin/lspci -nnk Code: 00:00.0 Host bridge : Intel Corporation Mobile 4 Series Chipset Memory
So decided to try a fresh install as ubuntu was having issues every update for me. Regardless i can't seem to get my wireless working and i'd really appreciate some help as i have no idea what i'm doing.
Using a hp pavilion dv5 1235dx.So my network card does show up it's a broadcom 4312 pci id 4315.Installed the b43 & wl drivers but it didn't help. The hardware switch is stuck at orange but in ubuntu it would function despite this(sometimes ).
I have a AR928X wireless card and everything I have tried has failed. The default driver ath9k scans and connects to my router but cant connect to any site or ping anything , same with the madwifi driver lspci prints 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
Well this my first time working with linux and openSUSE, and I love it. But one problem I can't overcome is my network card is not working. I went to bestbuy and bought the dynex enchanced wireless G card. Model # dx-ebnbc ver. 1011
I installed wine to run the .exe but that did nothing and gave me that the dll is not registered. openSUSE detects that the card is plugged in but the card does not light up or activate in anyway. The only way I can connect to the net is through an Ethernet cable.
I am having trouble getting a Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller to work on openSuSE 11.3. Most of the data for the problem is in this pastebin of the output of Framp's collectNWData.sh. I have also downloaded drivers for this card as detailed below.
I installed 10.3 (after buying it a couple of years ago and letting sit on the shelf) and can't get it to configure my ethernet connection or my wireless card. Yast doesn't include a list of available cards, and the error I get in installation-network setup is that the kernel isn't present. The machine I'm installing this on is a Lenovo, in which there isn't a discrete ethernet card (it's in the motherboard), but my wireless card (a Cisco LINKSYS 802.11G) is a discrete card. Because I'm divorcing Microsoft for a number of valid reasons, I don't have Windows available on that box.
i installed suse (KDE) on my old notebook and now I'm trying to get the wlan to connect to our router and can't figure out how to get it to work. My card seems to work, the network manager even finds the router, but i just cant get a connection. I followed the steps of the "Getting Your Wireless to Work" thread and these are the results:
- i messed around a bit with the network settings and might have cluelessly broken something (or broken it more)
- i tried a usb-wlan-card as an alternative, which didn't work either, but could possibly have messed things up even more.
wifi card:atheros ar5007egOS: openSUSE11.4My laptop can't connect on network after system hibernate. It has been asking me for enter the wifi password. But when I input the wifi password it still can't connect on network. I have to reboot it.
Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .
My Dell Vostro 1520's Dell Wireless 1397 WLAN Mini-Card must not have been set-up correctly, as the Network Manager won't even let me select the wireless tab. Please just explain to me, step by step, what exactly I must do to make it work! Additionally, I can't figure out how to disable my Touchpad's Tap to Click funtionality, which must be done if I'm to effectively use my current KDE installation of openSUSE
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
I have a Toshiba Satellite L305-SP6944C, Pentium Dual Core 2.16, 2GB RAM, 160GB hard drive, DVD-RAM UJ880AS, display 15.6 TFT widescreen, ethernet Realtek RTL8101E/RTL8102E PCI Express, WLAN Realtek RLT8187, Opensuse 11.2 and KDE 4.3.1. Installation was OK and finally the wireless card is working... but I don't have conectivity bacause in the browser (Firefox) appears a message saying "the server can't be found"
I follow the howto write by Swerdna. With ndiswrapper I install the XP driver for RLT8187, KnetworkManager is in charge of connections showing both eth0 and wlan0, the wireless sign of router Dlink DIR-280 is OK, in the dialog box of network connection I put the mac address of the wlan card but I think that is not the problem.
Other thing that I missed is that I don't find boot.ini at any directory to add modprobe ndiswrapper in the boot sequence, in etc/init.d/ appears a "boot" file, is this file that I have to change to modprobe ndiswrapper??
my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."
I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.
I've installed the Ubuntu 10.04 Server onto a PPC G4 Mac just for the experience of setting up a server. During the installation process Ubuntu couldn't auto-configure my DHCP Network. I'm using the airport card on a wireless network. How can I manually configure the network once Ubuntu is installed.
How do you find one that runs in USB and how do you find it when it runs from a pci port. i already know that you might be able to find the kind of driver that is required to run the device
Lots of people have accomplished this by using aircrack but some operating systems can't install aircrack (not to mention that the use of some software is illegal depending on where you live) so i want an alternative.