OpenSUSE Network :: Network Manager And Static IP Setup?

Jan 12, 2010

I'd like to have a set up where my Ethernet card has a static IP set up but my WiFi card doesn't.Currently I have a profile for this set up in Network Manager, however on boot up and every time I replug the cable Network Manager chooses the default "auto eth1" profile. I manually have tochoose my own profile for the Ethernet card every time. How can I make it default??I know the workaround would be to use ifup but then I lose the ability to quickly change access points for my WiFi card so that's not a solution for me

View 9 Replies


ADVERTISEMENT

OpenSUSE Network :: Enable Static DNS Address For Mobile Broadband In KDE Network Manager?

Mar 5, 2010

How do I activate static DNS for mobile broadband. I can't find any place to write down this information. Settings are made in Network Manager - not Yast.

View 3 Replies View Related

OpenSUSE Network :: Setup Fast Apache - Launch Static Html Pages

May 22, 2011

I would like to set-up a pretty fast a running apache. I would like to use him so to launch a pretty small web site of 10 static html pages. At this time there is no security concerns (even though I want to do it right) , because the computer has not even ethernet cable. I have some experience, 8 years ago I Was setting up virtual hosts in fedora, so this process is not a blackbox for me.

View 9 Replies View Related

OpenSUSE Network :: SUSE 11.3 No Network Access With Static IP

Aug 20, 2010

New SUSE 11.3 install connects to network/internet etc OK with DHCP-assigned IP address. When I switch to static IP, I can no longer ping internal network, or anything else. This works OK with SUSE 11.2 on same hardware and (as far as I can see) same setup. Some diagnostics are shown below.

Firewall
Disabling the firewall makes no difference.

Not using a network manager (can't see how to assign fixed address if I do - all greyed out).

ifup eth0:
eth0 device: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)
SuSEfirewall2: Warning: no default firewall zone defined, assuming 'ext'
(not sure why the warning - eth0 is assigned to external in the firewall setup).

[code]....

View 9 Replies View Related

Networking :: Use The Network Manager App To Set A Static IP?

Jan 12, 2009

In 8.04 I can use the network manager app to set a static IP.

In 8.1 the network manager doesn't seem to work. I tried many different permutations of settings and got nowhere. Even though I put in IP subnet and gateway it still does the DHCP config.

So I added lines to my /etc/networking/interfaces file like this:

auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.0.100
netmask 255.255.255.0
gateway 192.168.0.1

I then either reboot or do this: sudo /etc/init.d/networking restart

This made the network manager icon in the top panel vanish. An ifconfig showed that those settings are in place but DNS doesn't seem to be working. I can ping other hosts on my network by IP but not www.yahoo.com etc.

I even read the man, that's how desperate I got! (a config like the above seems to work on my 8.04 machine except that the auto eth0 appears at the end of the file.)

I didn't see how to set the DNS server(s), unless I was in the wrong man.

View 7 Replies View Related

Networking :: Static Network Setup?

Aug 16, 2010

I have a fresh install of Centos 5.x and I'm having issues on setting up the network...i know i have to edit/etc/sysconfig/network-script/ifcfg-eth0 and create an ifcfg-eth0:0 right?im just having issues getting everything setup correctly.my network setup:Router IP: 192.168.2.1IPs on network: 192.168.2.xNetmask: 255.255.255.0

View 3 Replies View Related

Ubuntu :: 10.04 Static IP Addresses Using Network Manager?

May 2, 2010

I have four PC's in a home network setup, no server just peer to peer using ssh. I have tended to use wicd to set static IP addresses because Network Manager didn't always perform as I thought it should. Now that I have installed 10.04 I cannot see how to set static addresses using Network Manager so I installed wicd, and disabled Network Manager. After setting the address with wicd it shows that the computer is connected to the internet however I cannot get internet access, though I can network with my other computers. I've uninstalled and reinstalled a few times just to check that I haven't been careless but the results are still the same.

View 8 Replies View Related

Fedora Installation :: Unable To Set A Static IP With Network Manager

Jun 22, 2010

I had been running Fedora 12 for some time without much difficulty until I had to change the motherboard of the computer. The new MB comes with Realtek 8112L PCIe Gigabit LAN controller.I am not able to use this LAN controller without Network Manager. The problem is I am not able to set a static local IP with it. Network Manager -> Edit Connections -> Auto eth2 -> edit -> IPV settingsAs soon as I change Method to Manual, 'Apply' button gets grayed out.I am not able to save any change.

View 5 Replies View Related

Ubuntu Networking :: Static Wireless IP With Network Manager?

Jul 3, 2011

I want to set up a static IP on my laptop that connects via wireless to my home network. I have 11.04 installed on my laptop. When I try to use the manual IPv4 setting in the network manager the save option gets greyed out. I tried to edit the /etc/network/interfaces file but all the examples I could find on the net refer to eth0. I tried replacing this with wlan0 but this did not work. I tried installing wicd but I kept getting "Bad Password" errors even though I know the password is correct. A number of people recommended uninstalling network manager to get wicd to work but many other posts said that uninstalling network manager didn't help so I didn't want to go ahead and uninstall unnecessarily. Besides I figure if Ubuntu is distributed with network manager there must be a reason for having it. So what do I do to get a static IP address for the client on a wireless connection?

1. I went to network manager and selected "Connection Information" On the information window I saw the following:

IPv4
IP Address: 192.168.1.6 (This is the item I wanted to change and make static)
Broadcast Address: 192.168.1.255
Subnet Mask: 255.255.255.0

[code].....

2. I went to network manager and selected "Edit Connections"
3. I selected the wireless tab and then the wireless network I wanted to edit
4. I clicked on the edit button and then I clicked on the IPv4 settings tab.
5. I changed method from Automatic (DHCP) to Manual

[code]....

View 8 Replies View Related

OpenSUSE Network :: Network Using Static IP

May 3, 2010

Recently our sys administrator decided to go to static IPs from the earlier assigned dynamic ones. This has created some havoc in my open suse 11 and I do not have access to network. I tried using the YAST network configuration manager, after everything is done it shows 'network wired' but unable to ping.

View 1 Replies View Related

OpenSUSE Network :: Network Manager Default Connection Can Handle Virtual Interfaces?

Jun 7, 2011

I've not found how to configure more than one ip address with network manager.Nor with kde nor with plasmoid network manager.I need several virtual ip addresses for eth0 when the "default" of eth0 is connected i.e. "Connected to Auto eth0" should initialize the virtual interfaces.I have not found no even how to configure the ip address.I think this will be used from ifup config in yast or not?There I have the virtual interfaces but they are not taken from network manager.And last but no least: Is it possible that when using network manager the eth0 is enabled even no user has logged in?

View 4 Replies View Related

OpenSUSE Network :: Susie 11.4 Network Manager Doesnt Start At Bootup

May 22, 2011

I am using an Acer Aspire 5536 AMD dual core laptop with a 64bit installation of Susie 11.4. Using 11.2 I had no problems connecting to the wireless router. As soon as 11.4 was installed, clean install, and the laptop rebooted, network manager failed to start, until manually invoked and then enabling networking through the system tray. Even after this it will not connect to a wired or wireless network sometimes for more than 30 minutes.

View 9 Replies View Related

OpenSUSE Network :: Network Manager Is Not Present In Tray Bar After Upgrading Gnome 3?

Jul 23, 2011

I tried to install suse 11.4 on the new gnome desktop 3. everything seems to work except the network manager. Is not present in the bar and I can not restore it. tried to reinstall network manager but to no avail.Does anyone know how I could solve this problem

View 1 Replies View Related

OpenSUSE Network :: Unable To Setup 10.3 As Samba PDC - The Network Path Was Not Found

Jun 1, 2009

I am trying for the last many days to setup my opensuse 10.3 as Samba PDC Server according to the URL mentioned below, but in vain:How to setup SUSE 10.3 as Samba PDC - openSUSE When ever I try to join a Windows XP machine to the domain setup on Opensuse, I get the error:'The following error occured while attempting to join the domain. The network path was not found'. What could be the reason for this error despite of the fact the I am able to ping the FQDN of the PDC from the XP machine, but the XP machine simply denies to join the domain because of the above mentioned error.

View 7 Replies View Related

OpenSUSE Network :: Wireless Not Responding, Hardware / Unable To Enable It Through Network-manager Applet?

Apr 4, 2010

I recently installed OpenSUSE 11.2 and everything works fine except wi-fi card, of course. The problem is that after installation the system recognized the card (is was listed in network devices in Yast) but I was unable to enable it through network-manager applet. Though the device could make scanning through terminal (found article in docs but didn't fully understand wpa_gui). Then i was stupid enough to delete the device from Yast list to try to reinstall it. So the problem is that i simply can't do this cause i see no way to re-detect. That is the goal is to at least turn back to post-install system state and try to enable wifi card again.

View 9 Replies View Related

OpenSUSE Network :: Network Manager & Bluetooth Systray Applet Takes Time To Load

Mar 5, 2011

I am using opensuse 11.3 64 Bit Gnome. The problem is the network manager & the bluetooth icon takes unnecessarily long time to load (2-3mins) & until it loads I cannot connect to the internet.

View 1 Replies View Related

OpenSUSE Network :: Setup As A Network Boot Server To Install Solaris 10 On A Sun Ultra 10 Client?

May 12, 2011

I have an opensuse 11.3 install which I want to set up as a network boot server to install Solaris 10 on a Sun Ultra 10 client. According to what I've read, this requires rarpd and tftpd which I've set up on opensuse, but also bootparamd which I can't find for 11.3. It seems it was last included with opensuse 9.2. Does anyone know if it's available, if I could use the suse 9.2 version, or any alternative?

View 3 Replies View Related

OpenSUSE Wireless :: Network Manager Stuck On 'setting Network Address' Then Continuously Prompts For Hex Or ASCII Key

May 28, 2011

When I attempt to connect to a wireless network, the network manager asks me for the network's password, then says 'setting network address' for 20 or so seconds, then asks me for some random Hex or ASCII key in the same type of window I put the password in (Secrets for Noel -- KDE Daemon). Since a key is already typed into the window, I press OK, which then causes the network manager to go back to 'setting network address', then the window pops up again and keeps repeating itself.

I'm running Opensuse 11.4 with KDE, and my driver is ath9k. I don't know much about linux so please don't tell me to 'recompile this' or 'change this setting' without explaining how to do it. Please help, I've been unable to connect to wireless in OpenSUSE for 2 weeks now.

View 9 Replies View Related

OpenSUSE Network :: Configure A Connection With YAST As Well As With Network Manager?

Feb 1, 2010

Im new in this world of linux and suse. I have just installed the opensuse 11.2 in a Dell Inspiron 5160. Such laptop has a BCM4306 Wireless LAN controller. When I tried to configure a wlan connection, I found that the firmware was not installed. After looking in different forums, I installed the firmware b43. Now, my wlan card is abled to find the wireless of my router.

I have tried to configure a connection with YAST as well as with Network Manager, but both cases failled. Specifically, when I use Network manager, Im able to see in the applet my connection, how strong is the signal, but I see a yellow symbol (in one forum, such a box is shown with a green symbol).

I have check many time all about the secutity, encryption, and so one and all seems to be correct. But when I open the mozila firefox or the konqueror browser, no chance to surffer in internet. Now Im just a step to become crazy. The drivers are ok, the information about the router and the keys are ok, but in such a way, I am still harmloss.

View 1 Replies View Related

OpenSUSE Network :: Connecting Mobile Via Network Manager In11.2

Mar 7, 2010

I m nokia mobile to connect to internet in 11.2 configured it all in n/w manager with phone number *99#

APN: XYUX(as given by provider)

Also wrote the dns in resolv.conf but all in vain . it is not connecting neither dialing any number just shows "activating" but with no progress earlier in 11.1 i used kinternet (but i couldn't find it here) is there not any other dialer ? as i ve heard that n/w manager is quite troublesome.

View 7 Replies View Related

OpenSUSE Network :: Network Manager Won't Connect To Wireless Router

Apr 15, 2010

All settings are correct as far as i can tell. The wep key works on all my windows boxes. When i have connect automatically enabled it never tries to connect. if I go to edit it it pops kde wallet up i put in credentials. wallet goes away then nothing happens. if i double click connection to my router also nothing happens. I have the wep key in there and i even made it visible to make sure.

View 5 Replies View Related

OpenSUSE Network :: Network Manager Not Detecting Wireless Device?

Sep 25, 2010

Having a hard time getting NM to detect wireless usb device: Linksys model WUSB600N. Here are a few commands I do know about.

iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.

[code]....

View 9 Replies View Related

OpenSUSE Network :: Cannot Start Network Manager - To Configure My Wlan ?

Nov 27, 2010

I have just installed opensuse 11.3. I am absolutely new for Linux and for this forum. I have tried to open Network manager to configure my wlan. But its not starting. How to start network manager and configuring my wlan.

View 4 Replies View Related

OpenSUSE Network :: Add Network Manager Notifier In Open Suse 11.3 KDE?

Apr 4, 2011

I mistakenly delete my default panel. How to add the network notifier? Tried to look for the widget but nothing? i need to choose my network connections. And when i look at the Network manager my wireless if black ? It means it didn't detected my wireless?

View 8 Replies View Related

OpenSUSE Network :: View Of The Network Manager In System Tray?

May 21, 2011

openSUSE 11.4 | SUSE Linux | Beginner's guide to multimedia codecs MP3 DVD 3D nvidia ati wireless wi-fi netbookplease see the second image under wireless driver installation in above link.it is a image of a network manager when we clicked the network manager icon in system tray.but i am not getting the like that.if i click that icon i will see only a small window only with enable networking,enable wireless and manage connections only.how to get a detailed windows like that in the image.

View 9 Replies View Related

OpenSUSE Network :: Network Manager Gnome 3 - 11.4 Mobile Broadband ?

Jul 20, 2011

I want to use my laptop to share network for VoIP adapter. I'm using mobile stick as well as wi-fi and Network manager under Gnome 3. Voip adapter asks for address via DHCP to gain the access to the server some where in the other side of the world.

View 6 Replies View Related

OpenSUSE Network :: How To Stop Kwallet From Interfering With Network Manager

Aug 12, 2011

I'm putting a opensuse 11.4 64 bit KDE install on an HP -G62 laptop.

I also use an NFS network.

I want to use a wireless network.

The problem is that network manager keeps insisting on asking kwallet for permission to start up the network. As a consequence boot hangs because the nfs network can't find the files in /etc/fstab because the network can't start because you can't see kwallet until it finishes booting.

I have options set in networkmanager to store the password in connection secrets in secure storage, and it insists on asking kwallet!

I don't want to get rid of kwallet because it's very useful otherwise - just not at boot time?

How do I modify the behaviour shown here?

View 1 Replies View Related

OpenSUSE Network :: Setup Xen Virtual Nodes We Encountered One With The Network?

Jan 26, 2010

while trying to set up Xen Virtual Nodes we encountered one issue with the network (which is why it is posted here On the DomU the interface is provided by a bonding -bond0- of three NICS. Now the Xen network script a) does not take this bonding b) destroyes even this bonding From a number of posts I assume I have to configure this by hand, correct? Is there an instruction how to do this? Simply create a bridge on top of bond0??

View 1 Replies View Related

OpenSUSE Network :: Network Manager Won't Accept Security Key?

Feb 22, 2009

The network manager will ask me for my security key and it will not accept it. Instead when I use the show password feature to see what I typed in was correct, it shows something completely different than what I typed. For instance if my Key was :when it pops up and ask to for me to retype it again it shows something completely different in hex. Is there anyway I can use a different network manager?

View 8 Replies View Related

OpenSUSE Network :: Can't Use Network Manager To Connect To Internet

Jan 10, 2010

the thing is that I cant use Network Manager to connect to Internet, because it simply do not connect. The connection, although, awailable throught yast when i choose "traditional method with ifup", so everything is just fine, but if i need to reconnect, i have to reboot. How do I setup a !working! connection through Network Manager, or maybe i do not do something properly.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved