OpenSUSE Network :: 11.3 - No Network Connectivity - Audio To Work On Skype

Oct 16, 2010

I had Kubuntu 64-bit installed and decided to try OpenSUSE instead as I was having problems getting the audio to work on Skype. After installing OpenSUSE 11.3 (64-bit), I do not have network connectivity (Ethernet or Wireless)? Neither adapter can be detected? I thought the install would be fairly straightforward as Kubuntu 64-bit detected all the hardware.

View 6 Replies


ADVERTISEMENT

OpenSUSE Network :: Create Network Bridge / Device Hooked Up Via Ethernet Had No Internet Connectivity?

Feb 25, 2011

I'm on opensuse 11.4 (11.3 won't work with my monitor).

My computer gets internet through wireless and I want to share that internet through its ethernet port. So far I've tried using Knetworkmanager to create a network bridge between my wireless and wired connections. I created a new wired connection and shared it using the ip address settings. I was able to get both connections active, but the device hooked up via ethernet had no internet connectivity.

I also tried this command:
echo 1 > /proc/sys/net/ipv4/ip_forward

but another test resulted in the same fashion (no internet on wired). I believe anything I add to /proc should have an immediate effect, correct?

View 9 Replies View Related

OpenSUSE Network :: 11.4 Ath USB WLAN Does Not Work Except Skype?

Jul 6, 2011

Being in China has some disadvantages reagardings internet.To enjoy unfiltered speed and access I use my non mainland mobile phone card.

Using LAN works fine in the office.But if I connect the WLAN USB dongle except skype nothing works.

ifconfig
eth1 Link encap:Ethernet Hardware Adresse 00:1A:A05:26:C5
inet Adresse:192.168.1.3 Bcast:192.168.1.255 Maske:255.255.255.0
inet6 Adresse: fe80::21a:a0ff:fed5:26c5/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
code....

View 5 Replies View Related

OpenSUSE Network :: Xen NAT Setup In 11.2 - No Basic Connectivity?

Feb 21, 2010

I am experimenting with Xen with the standard kernel (kernel-xen package) and utilities. I already got bridged setup to work with a single domU, but found out that because of my wireless card I cannot expect bridging to work when connected wirelessly. Now I am trying a NAT setup but I cannot seem to get any network connection from the domU to the dom0 and viceversa. Comparing the network devices and routing tables of others, I cannot see any problem.

The domU runs with IP 10.0.0.1 and the dom0 has a vif with IP 10.0.0.128 with a default gateway of 10.0.0.254. Pinging from the domU to the dom0 and viceversa does not show any traffic at all when I use tcpdump to monitor eth0 in the domU or the vif interface in dom0. It seems that basic connectivity of the vif interface and eth0 in the domU does not work. Any tips on how to debug this problem?

View 1 Replies View Related

OpenSUSE Network :: Changing MAC Using Ifconfig Causes Connectivity Lost?

Jun 15, 2010

I am using Suse 10 sp2. By running ifconfig I am changing the mac address. Everything is happening successfully, but this is adapter losing the network connection. Even when I give a static IP. I am not able to ping any other IP.

View 9 Replies View Related

OpenSUSE Network :: WiFi Internet Works Fine But Limited Connectivity Elsewhere?

Feb 22, 2010

I'm using 11.2 with KDE.

I can connect to the Internet on my WLAN just fine (using Opera) and can dload torrent files (using the same).

However, I have had trouble accessing some community repositories in the past, cannot synchronise with an NTP server (annoying since my battery is low and time and date are reset most reboots) and cannot use the lyrics function or Wikipedia function in Amarok. Nor can I connect to the net using Firefox (though conqueror works just fine...) I cannot download torrents on KTorrent either.

It seems that there is some sort of 'permission'/connectivity issue.

View 8 Replies View Related

OpenSUSE Network :: Network - Browsing The Internet With Domain Names Does Not Work

Jun 25, 2010

In short: browsing the internet with domain names does not work. The long version: I've configured my network with DHCP and ifup. Ping works on my internal net and with servers in the internet. Dig work's too! I get the right IP to the requested domain. When i try to access the internet using firefox or even wget i get an DNS error. For example wget is showing the following error: Resolving heise.de... failed: Name or service not known. wget: unable to resolve host address 'heise.de'

Again dig show me the right IP and if i add the entry to /etc/hosts it work's too! I've even tried it with manually setup of ip address, nameserver and default gateway but with the same result. Switching off the firewall has no effect on this problem, too.

View 9 Replies View Related

OpenSUSE Network :: No Network Connection After Firwall Settings Changed / Get It To Work?

Nov 17, 2010

I deleted the firewall files "K09SuSEfirewall2_init", "K01SuSEfirewall2_setup", "S11SuSEfirewall2_setup" and "S01SuSEfirewall2_init" from "/etc/rc.d/rc5.d" in order to disable the firewall when rebooting.

As a consequence all network services are not working. I can't connect to any other machine nor to the internet.

I rebuilt the symbolic files based on the ones for runlevel 3, but still no network services are available.

Any suggestions how to make it work again? I'm using Suse 11.3.

View 9 Replies View Related

OpenSUSE Network :: Network Not Work \ After Install All Packet On Test Internet / Update Was Error?

Jan 5, 2011

I install from openSUSE-11.3-NET-x86_64.iso. Installation was succesfull, but after install all packet on test internet / update was error. And after log in in installed system internet not work. I use router with DHCP

View 8 Replies View Related

OpenSUSE Network :: Literally ODD - Network Services Don't Work Every Second Boot?

Sep 14, 2010

I have an OpenSuSE 11.1 in vmWare ESX and every other boot I can't access any running network services (ssh, webmin, qmail, mysql, ...) from outside. I just need to login, reboot and voila - network services are working.I gradually updated to 11.2 and 11.3 by following the wiki with success but this problem remained. So I reverted to snapshot of 11.1 and now I would like to identify and solve the problem here first.I also looked at /var/log/messages /var/log/boot.msg /var/log/lastlog but can't find anything usefull. I will now compare those files from the working and non-working boot but meanwhile someone already has an idea or experience what could be wrong?

View 3 Replies View Related

Debian Hardware :: 8.1 - Network And EDP Video / DP Audio Not Work

Sep 24, 2015

I have the Debian 8.1 problem on the Intel Broadwell system , there are some issue which we have been found below.

1.Onboard eDP panel is not work.
2.Onboard DP audio has no sound
3.Intel WLAN is not work.
4.Intel onboard LAN is not work.

OS : Debian 8.1

CPU: Intel i5-5300U
Graphic : Intel HD Graphics 5500
Wireless : Intel wireless 7265AC

View 0 Replies View Related

OpenSUSE Network :: Trying To Find Out Skype Alternative

Jun 6, 2011

Last two days I am trying to find alternative to skype. So I decided to find solution for my family, friends to chat, call (audio, video) using opensource product on linux. I have tried the following: (using same clients and gtalk accounts on both test machines)

1. Kopete 1.0.80
Firstly, I like it because it is native in opensuse KDE system.
Secondly, it has optional jungle support for gtalk, which is ok for me.
The only problem, I cannot turn on jingle support, because there should be talk.google.com server , but the right server is gmail.com. Only with gmail.com server I can connect to my gtalk. I was managed to do it right, but my friends do not have jingle settings (libjingle installed). What should we do? Will we be able to talk when we activate it?

2. Pidgin 2.7.10 (libpurple 2.7.10)
Video calling, audio calling doesn't work at all. We using same version of pidgin on two computers, there is mention that it is calling but no progress after, nothing. Even camera turns on (no image though) but after doesn't turn off (camera light).

3. PSI 0.14 patched
Psimedia installed, doesn't call at all. Says that the client reject me or busy.

4. Empathy 2.32.2
No options for video and audio hardware, nothing to change at all). Call from menu doesn't work, nothing happens after I press "call". Call from chat window impossible because buttons are grey, are not active. Now error "could not sync the state of the new nicesrc with its parent"

5. Gajim
Even after writing down stun server stun.ekiga.net call buttons for video and audio call were inactive, unable to make call.

6. Ekiga
Using pctel.ru. Works ok, sometimes problems with intiating video, but still something. I am not very happy because it is not XMPP.

7. Twinkle works like a charm. The only one client using which I haven't had any problems at all. The only thing to tailor is audio codec (also encryption if you like).

I hope to make a call one day and to be sure that I haven't used any closed program for it!

View 9 Replies View Related

OpenSUSE Network :: Use Skype But Can't Browse Pages With Firefox?

Nov 22, 2009

I have openSUSE 11.2 64-bit KDE, I have installed it with lan cable connected, install updates and than switch to wireless.Everything worked great until I went to my girlfreind with laptop, there I can connect to router, use Skype but can't browse pages with firefox, can't install packages with YAST Also wired connection gives the same result but her PC have no problem with Internet.I have traied ifup, deleting /etc/resolv/conf, disabling NetworManager routing options with no succes

View 9 Replies View Related

OpenSUSE Network :: Cannot Connect With Skype - Don't Change Settings?

Dec 22, 2010

If you cannot connect with Skype, don't change your settings. The problem comes from Skype. Google for Skype outage.

View 4 Replies View Related

OpenSUSE Network :: Skype 2.2 On OpenSUSE 11.4 Mic And Video Not Working / Get That?

Aug 28, 2011

I have a fresh install of openSUSE 11.4 with KDE. This includes ALSA and Pulseaudio.

I have a mic and speakers and a webcam. As far as I can see microphone and sound reproduction work, the webcam also works:
- I can arecord and aplay
- KMix works
- amixer and alsamixer work (I am using microphone boost)
- test sounds play
- the webcam works in "Personal Settings (Configure Desktop)": Hardware > Multimedia > Phonon (test camera)
- Pidgin and Empathy work with sound and video.
(had to set this: gconftool-2 --set --type=string /system/gstreamer/0.10/default/audiosrc pulsesrc,
without this setting it was set to alsasrc by default and Pidgin and Empathy didn't work).

I installed Skype 2.2 (also tried 2.1) and tested the video camera in Skype. Result: doesn't work.
I made a test call: I hear the voice of the lady answering the call, but my own voice is not recorded.
In Skype everything is set to use Pulseaudio.

I am at a total loss to understand what is going wrong here. Why does Skype not work, when everything else does??

I made this observation:
When an application records something, a "Capture stream" shows up in the KMix "Capture Streams" tab. For example, when I use arecord, "ALSA capture" shows up, while I record. When I make a call on Empathy, a capture stream shows up in the said tab.

When I make a Skype call, NO capture stream shows up, so obviously Skype is not capturing anything.

View 9 Replies View Related

OpenSUSE Network :: Wireless Card Realtek 8187 Connectivity - (Firefox) "the Server Can't Be Found"

Dec 3, 2009

I have a Toshiba Satellite L305-SP6944C, Pentium Dual Core 2.16, 2GB RAM, 160GB hard drive, DVD-RAM UJ880AS, display 15.6 TFT widescreen, ethernet Realtek RTL8101E/RTL8102E PCI Express, WLAN Realtek RLT8187, Opensuse 11.2 and KDE 4.3.1. Installation was OK and finally the wireless card is working... but I don't have conectivity bacause in the browser (Firefox) appears a message saying "the server can't be found"

I follow the howto write by Swerdna. With ndiswrapper I install the XP driver for RLT8187, KnetworkManager is in charge of connections showing both eth0 and wlan0, the wireless sign of router Dlink DIR-280 is OK, in the dialog box of network connection I put the mac address of the wlan card but I think that is not the problem.

Other thing that I missed is that I don't find boot.ini at any directory to add modprobe ndiswrapper in the boot sequence, in etc/init.d/ appears a "boot" file, is this file that I have to change to modprobe ndiswrapper??

View 9 Replies View Related

OpenSUSE Network :: Skype Aborting On Launch - Tray Icon Will Pop Up For 1 Second And Then Just Disappear

May 27, 2011

Wondering if any one else is having this problem lately under 11.4. My Skype does not want to launch any more. When I click to open Skype, the tray icon will pop up for 1 second and then just disappear. Have tried launching from command line to see if there are any messages, but it just says aborted when you try launch it.

I noticed this started happening randomly when I had the laptop in hibernate and then would resume, Skype would then just disappear and then I would just relaunch it and it would be find again.

View 5 Replies View Related

OpenSUSE Network :: 11.4 - Firefox Fails To Connect To Internet (Skype Intact)

Jul 26, 2011

I have a Lenovo S10e netbook running a pretty clean version of 32bit opensuse 11.4, with very few standard patches since I installed it all those moons ago. The problem is that firefox cannot connect to the internet, the odd bit is that skype has no such problems. Are there any network related functions that that typically go screwy that might cause such a problem? The netbook really hasn't been used much for tinkering to have 'accumulated' a problem, but I'm about to give it to the extremely non-technical parents in law and cannot have it misbehaving, especially not as they are in a different country.

View 8 Replies View Related

Hardware :: No Network Connectivity?

Jul 18, 2009

I just installed a linksys router for the computers in my house. All the MS windows computers work but the linux computer that I use does not work.

View 2 Replies View Related

Fedora :: Unable To Get Network Connectivity Up?

Jul 30, 2009

Tried to re-install Fedora 11 since I haven't been able to get my network connectivity up for some reason. But during the boot process it got into a comand prompt complaining about some boot record problem and the need to create a soft link to /etc/root.

View 3 Replies View Related

Fedora :: Network Connectivity Drops Out Randomly?

Jan 21, 2010

Installed Fedora 12 recently.

For some reason, my network connectivity drops out randomly. This has happened between 5 minutes to 1 hour of booting and logging into the machine.

When the internet does work, its great, and super fast !

When it drops out, Internet stops working, cannot ping to external site and I cannot ping my router 10.1.1.1

I have onboard realtek network ports on my motherboard.

View 6 Replies View Related

Ubuntu :: Not Getting Network Connectivity Via Ethernet Cable?

Jul 14, 2011

I've just installed Ubuntu Desktop and connected the ethernet cable, but I don't have network connectivity. Why?

View 7 Replies View Related

CentOS 5 Networking :: Static Ip - No Network Connectivity

Oct 27, 2009

I'm having strange difficulties in setting a static ip for my CentOS 5.4 installation. If I use DHCP everything is fine, but with a static ip I have no network connectivity. I have done this many times with RedHat/Fedora/Ubuntu etc. with no problems and now I have no idea what I'm missing or doing wrong. I have tried to set ip as 192.168.1.20 (anything below .100 will do). GW is 192.168.1.1 and NM is 255.255.255.0. This is all I have had to use with other distros, but now when I set these I cannot even access my routers admin page or ping it (192.168.1.1). (I just did this with Vista on my other machine and all worked fine).

View 13 Replies View Related

Ubuntu Networking :: Eth0 Won't Enable - No Network Connectivity

Aug 24, 2010

Trying to get the wired nic working so I can troubleshoot the wireless. I cannot get any kind of network activity. Been searching so I will post a little information that seems to be common with my situation.

lshw -C network

reveals:

WARNING: you should run this program as super-user.
*-network DISABLED
description: Ethernet interface
product: 82562EZ 10/100 Ethernet Controller
vendor: Intel Corporation

[code]....

View 9 Replies View Related

Ubuntu / Apple :: Getting ANY Network Connectivity On Macbook 5,5 Running 10.10

Oct 24, 2010

Anyone have success setting up either wireless or ethernet connectivity on a Macbook Pro 5,5 on the 10.10 Maverick install? Normally in the past with 10.04, etc... I just plug in my ethernet cable and update my wireless using "sudo apt-get install bcmwl-kernel-source", but I can't even get my ethernet to work. I tried to load it from the live CD once logged in but couldn't figure it out.

View 9 Replies View Related

Ubuntu Servers :: Plugged In The Ethernet - No Network Connectivity?

Jul 14, 2011

I just installed Ubuntu Server, plugged in the ethernet cable, and there is no network connectivity.

View 2 Replies View Related

Red Hat / Fedora :: Xend Kills Network Connectivity On Boot

Oct 31, 2010

red hat 5 update 4 64bit. linux newby. on an interactive boot i can ping -t my vm linux server from my physical MS XP workstation and a vm W2000 64 bit server until xend is started, after that i get destination unreachable. if i choose not to start xend on the interactive boot i retain connectivity. i have read some blogs that imply this might be a bug - is this so? do I need xend on my vm red hat box that is a database server?

View 1 Replies View Related

Networking :: Network Server (DHCP) - No Connectivity To Modem

May 4, 2010

Basically, I wanted to use the Bootp (PXE) protocol to boot a machine (my laptop) from my network instead of using USB/DVD boot medias to reinstall if need be. My router being a piece of crap, I couldn't setup the DHCP server to allow PXE packets. Confirmed from the manufacturer that it is not possible. Well for a $140 router, you would expect the opposite. Anyways, here I am with a small machine setup with Slack, no desktop environment (only CLI) and connected to my router (which I deactivated the DHCP) so the machine can act as a DHCP server. It works very well. However, I would like to install a few other utilities into that machine and for them to work, I need to put the machine between my cable modem and my router. Basically, here's the topology from outside):

Internet (ISP) --> Modem --> DHCP machine --> Router (no DHCP - acting as a switch) --> computers & printers

The problem is that I cannot connect to the modem from the computers on the network. Also I cannot access the internet (go on the WAN side) from the computers. From the computers (namely my laptop), I can ping the router, but cannot ping the interface where DHCP broadcast. Also I cannot ping the modem. From the router (using the web config page), I can ping the DHCP broadcast. From the DHCP machine, I can ping the modem. In the DHCP server, I setup the eth0 (the interface where the modem connect to) as a DHCP assigned IP so it can obtain the IP from the modem. The eth1 (the interface where DHCP broadcast) is static. All my machines obtains a IP from the DHCP machine without a hiccup.

View 13 Replies View Related

General :: Xend Kills Network Connectivity On Boot?

Nov 1, 2010

red hat 5 update 4 64bit. on an interactive boot i can ping -t my vm linux server from my physical MS XP workstation and a vm W2000 64 bit server until xend is started, after that i get destination unreachable. if i choose not to start xend on the interactive boot i retain connectivity. i have read some blogs that imply this might be a bug - is this so? do I need xend on my vm red hat box that is a database server?

View 1 Replies View Related

OpenSUSE Network :: Can't Find Network Hard Driver On Network?

Oct 31, 2010

On Linux Mint (Gnome) i used to go to Network drive. that is on the right hand side of Nautilus there is a short cut for Network. in there i could see my network hard drive and other laptops connected to the network, and i could access my files. but on OpenSuse, when i open the network folder, nothing comes up. may be it needs some sort of configuration.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved