OpenSUSE Install :: LV's No Longer Accessible After Update From 11.3 To 11.4

Aug 26, 2011

after upgrading 11.3 to 11.4 with zypper dup my logical volumes are no longer accessible The YAST Partitioner recognize them as Linux Raid but I could not mount them.

linux-dv06:~ # blkid
/dev/sdb1: UUID="3ed0f7a9-8986-254c-a14d-c8941769f33a" UUID_SUB="b558e84e-6369-8803-f65f-455bd0e5f0f7" LABEL="linux-2zun:0" TYPE="linux_raid_member"
/dev/sda1: UUID="482595d1-cbf0-43fb-8026-1ed4d1229fbc" TYPE="ext4"
/dev/sda5: UUID="f30bb3a9-2690-403f-9f45-45c3379a512b" TYPE="ext4"

[Code]....

View 2 Replies


ADVERTISEMENT

OpenSUSE Install :: Ubuntu Grub2 No Longer Detected 11.3 After Online Update

Jan 6, 2011

I was using tripleboot system in one hard drive. That included Windows 7,Ubuntu 10.10 and Ubuntu 11.04. And yesterday I decided to added openSUSE 11.3 at another partition. I'm using Ubuntu 11.04 grub2 as bootloader.

At first there was no problem. All OS detected well, but after opeSUSE online updates last night my openSUSE partition won't boot. First, at boot I chose openSUSE and it said "Boot kernel first" and nothing happens. And then I boot to ubuntu and ran update-grub then I saw grub no longer detected openSUSE partition.

View 9 Replies View Related

General :: Network Computer Is No Longer Accessible?

Dec 13, 2010

When i first install ubuntu 10.10 the other day my entire windows shared network was visible and accessible through places/network ect.i only had an issue creating a link.Now , for some reason i can no longer see the other windows comp or any of its folders but i can see my sons laptop ( running vista) . obviously i still have access to the network and i have checked the sharing settings on the windows machine.

View 3 Replies View Related

Ubuntu Networking :: Open Linksys Router No Longer Accessible

Aug 28, 2011

I have a linksys router in my basement and physical access is pretty much blocked by a stuck trap-door. I could try to shut off the main power switch, but I like to see that as a last resort. The problem I have is that I have an open (no encryption) wifi connection between my pc and linksys router, yet I cannot connect to it. Until a couple of days ago I could connect to it with my android handheld device, my linux laptop, and my windows desktop. All these devices are now unable to connect. I attached the wicd log from my linux laptop. How to gain access to my router again?

View 9 Replies View Related

Ubuntu :: Compiz Stopped Working, CompizConfig Settings Manager No Longer Accessible?

May 18, 2010

I did a clean install of Ubuntu 10.04 on a Toshiba Satellite, Intel graphics card, a few days ago, and had no trouble accessing the CompizConfig Settings Manager. I changed a number of settings, and everything seemed to be working just fine. But two days ago, I noticed that the compiz effects (rotating desktop cube, minimize effect etc.) were gone; and when I now try to access the Settings Manager, I see a "Starting CompizConfig..." appear in the panel and linger for about five seconds; then it's gone. No settings manager, no error message.

The day that happened, I had (to the best of my memory) not installed any updates. I had, however, removed a bunch of applications through the Software Center. I had also launched Ubuntu Tweak and changed a couple of settings. The only option it showed, and shows, under 'Compiz Settings' was then (and still is): "Prerequisite Conditions" : "Install Advanced Desktop Effects Settings Manager". The box was checked. I have since unchecked and re-checked it, thereby uninstalling and re-installing the settings manager. But that hasn't changed anything.

[Code]...

View 9 Replies View Related

Slackware :: Dead Items At Slackbuilds.org - Default Source Tarball Is No Longer Accessible

Oct 6, 2010

Recenlty I installed sbopkg for maintaining slackbuilds scripts and I found it very useful. But there are some limitations coming from outdated repositories for older version of slackware. Eg. a tar ball with Maxima source maxima-18.1.... which is default in the slackbuilds.org repository for slack 12.2 doesn't exist at this moment. One can find older and newer versions. I understand that maintainers of slackbuild scripts are rather focused on recent slack version. Nevertheless such outdated entries should be somehow marked

in the way that a visitor will know that a default source tarball is no longer accessible. Maybe persons who submit the scripts should be responsible for keeping track for a sources. If that problem won't be solved it is a danger that slackbuilds.org will play only a role of some addons to the very recent slack release - but if this will be a case then simpler is to build say additional two or three DVD's of packages.

View 14 Replies View Related

OpenSUSE :: Gnome No Longer Starts After Update?

Jan 21, 2011

since the last SuSE online update (last Wednesday?) the X server no longer starts on our notebook (ATI HD 4200) so we only have the consoles available, which limits the WAF heavily . We were using SuSE 11.3 with the Gnome desktop for about one months and it worked smoothly, but since the update (which included a kernel update to 2.6.34.7-0.7) the X server tries to start 5 times and then gives up. All logfiles end with:

Code:
...
[ 13.899] Segmentation fault at address 0x3c
[ 13.899]
Fatal server error:

[Code]....

I used the ati driver ati-fglrxG02-kmp-desktop, version 8.762_k2.6.34.0_12-31.1 from the ATI Suse repository. To solve the problem I already switched to the Xorg driver which lead to a color distorted display but no segmentation fault. But I'd like to get the ati driver running again.

View 9 Replies View Related

OpenSUSE :: Virtualbox No Longer Running Since NVidia-Update

Sep 11, 2011

Trying to start a running installation of virtualbox I get:

And it seems that it doesn't work with the new 275 build I got pushed when updating. Updating virtualbox didn't help. Besides uninstalling the 275 version of nvidia and installing the 270.

View 4 Replies View Related

OpenSUSE :: After Update To Ubuntu In VirtualBox Shared Folder No Longer Mounting

Oct 6, 2010

I recently applied a bunch of updates to my guest OS (Ubuntu) inside VirtualBox (NOTE: NOT updates to virtual box. Updates to the OS) and now on startup, I get the error:

"An error occurred while mounting /media/share. Press S to skip mounting or M for manual recovery"

I tried a fix which said to comment out the mounting in /etc/fstab and instead put it into rc.local, but this does not work.

Also, when I press "M" to try it manually and type:

mount.vboxsf -w mysharedfolder /media/share

I get the error:

mount.vboxsf: mounting failed with the error: No such device

But before I updated Ubuntu, that shared folder worked perfectly!

View 1 Replies View Related

Fedora Networking :: Internet Not Accessible After Update / Reboot

Mar 3, 2010

After a recent update and reboot, I can no longer access the internet. Typing google.com in firefox or elinks results in firefox/links complaining about the server not found. However, I can find the server by using dig on the command line. I have checked the DNS configuration in resolve.conf and it is exactly the same as on a RHEL 5 system connects fine. The strange thing is, I can connect to other local machines in my domain just fine but can not connect to any other machine on the internet on this one Fedora 12 host even though I can on all other machines!

View 11 Replies View Related

OpenSUSE Install :: Can't Update (by Update Applet), Install Codec, New Software

Jul 19, 2010

i am a new opensuse user from vietnam. I installed opensuse 11.3 last week, and i have a serious problem with repo. I can't enter it . It's mean i can't update (by update applet), install codec, new software, .

View 1 Replies View Related

OpenSUSE Install :: No Longer Get GRUB's Boot Screen

Jan 28, 2010

I've run into a strange problem recently. My primary OS right now is Windows 7, and OpenSUSE is secondary. I had GRUB as the bootloader, and everything seemed fine, but I ran into one problem in Windows 7: one program refused to work correctly with ATI forced anti-aliasing on, but it is needed by others (or else edges look jagged).So I decided to install ATI Tray Tools. But it seems that Windows 7 is being evil and won't let install drivers that their creators didn't pay Microsoft for (thank goodness that's not the case in Linux). That means I had to use a driver overrider program, and that means that it had to change the Windows 7 BCD options. And that's where bootloaders kick in. It seems that Windows 7 is too lazy to check for its BCD on other than active partitions, so it doesn't allow the overrider to function.

So what I did was change GRUB to boot Windows 7 with makeactive flag. The problem now is - it won't deactivate! I no longer get GRUB's boot screen, it just boots to BCD directly. So my question is - is there a way to deactivate (or, rather, reactivate the /boot partition) after Windows 7 shuts down or restarts automatically? Obviously I don't want to use GPartEd each time I want to boot to Linux.

View 7 Replies View Related

OpenSUSE Install :: Geeko No Longer Shown At Boot?

Jan 16, 2011

I updated my GRUB config. I reordered some menu items and set openSUSE as default OS.When I boot into openSUSE, I am no longer greeted by Geeko when openSUSE is loading. I only see text from the boot procedure scroll by like it's still the 90s. While there's a certain coolness in seeing openSUSE switch to runlevel 5 and all that jazz, I want my chameleon back.A few weeks ago, I configured openSUSE to boot with flag vga=0x3ef so that it would boot with my preferred resolution immediately. This used to work fine. Since this morning, openSUSE crashes when X is attempting to start. I can still boot into openSUSE by removing that flag, but even then I still don't see the chameleon.

View 9 Replies View Related

OpenSUSE Install :: OpenSySE 11.4 - Keyboard No Longer Works Under X?

Mar 19, 2011

I have new install of 11.4 X86_64 which has been working fine up until this morning. Now when I boot and get the kdm login screen, the keyboardis no longer working, nothing appears from typing, no key sequences are recognized. The mouse works fine and when I go Console Login, the keyboard works fine.The mouse and keyboard are both Logictech wireless using the Logitech unifying usb link. As I said, it was working fine until this morning.I have no idea how to even diagnose this.

View 8 Replies View Related

OpenSUSE Install :: Find Packages That Are No Longer Present In Repository

Jul 19, 2010

I want to clean my system out of old packages. I can use rpmorphan to find orphaned packages, but how do I find packages that are not longer present in their vendor repository?

View 2 Replies View Related

OpenSUSE Install :: Ubuntu No Longer Shows In Boot Options

Mar 10, 2011

Everything went fine but whenever I rebooted, Ubuntu 10.10 was not an option in the boot list. However, Windows shows up and boots just fine. I am currently tri booting (not sure if that's the correct term) Windows 7, Ubuntu 10.10, and OpenSuse each on a hard drive of their own. In the dolphin file manager I can still see all the files for Ubuntu so I know it was not partitioned over or deleted.

View 7 Replies View Related

OpenSUSE Install :: Can No Longer Boot Into 11.4 After Updating NVIDIA Drivers

Apr 24, 2011

Basically everything was going fine, and i was enjoying the OpenSuse experience, then downloaded djl (Games Launcher) , installed some games and found that i had a very very very bad frame rate (about 1FPS), and my GPU is a NVIDIA GTS250 (1GB), and runs most games flawlessly under m$, so i went about installing the graphics drivers for my card. I followed the instructions and was under the assumption that i installed the correct ones, but now i cannot boot into any graphical interface. I think that it should be a graphics issue, as this was one of the few things done before rebooting. I have tried booting into the normal mode, and the failsafe, I have read many other "Not booting'' posts, and have tried their solutions without success, there include: Changing the boot parameters Logging in and manually trying to boot up the gui (init 3.... init 5... etc)

When the computer tries to load up OpenSuse in normal mode, it comes up with the normal loading screen, and then about 90% of the way it stops for about 30 seconds, and then switches over to a CLI, asking for a login, going through the log a couple of things fail, did have these noted down (but cannot find and will post along with other commands that i am asked to do) I want to try and avoid a reinstall as it took me a long time to get the WiFi card working.

View 9 Replies View Related

OpenSUSE Install :: Can't Longer Access LUKS Encrypted Volumes?

Aug 26, 2011

I've had everything but /boot on LVM LUKS encryption since I installed 11.4 on my netbook. Suddenly it won't accept my password and boot. Nothing had been updated since the last successful boot. The only possibly different thing that occurred was that I had plugged in my Android phone to charge before it booted up. Anyway, the specific error it gives when I enter the password (and I'm absolutely sure it's the correct password):

Code:
No key available with this passphrase.
Here is everything else on the screen:
Code:
doing fast boot
Creating device nodes with udev
[number (not sure if relevant/unique)] fb:conflicting fb hw usage inteldrmfb vs VESA VGA - removing gen
Volume group "system" not found

[Code]...

View 9 Replies View Related

OpenSUSE Install :: EXT4 And Power Outage - No Longer Mount At Boot-up

Sep 24, 2010

Due to a power outage, my EXT4 file systems (which contain /usr and /opt) no longer mount at boot-up. They are, however, seen by disk utility in Knoppix, so I assume the data is still there and that it's just matter of making a connection to it.

View 6 Replies View Related

OpenSUSE Install :: Online Update Fails To Refresh Update Repo?

Sep 21, 2010

when I launch Yast2 - Online Update, I get an error during the repository refresh that it could refresh the repository.Since it's easier to copy-paste - here is the output from 'zypper ref' with the same error:

Code:
Retrieving repository 'Updates for openSUSE 11.3 11.3-1.82' metadata [|]
Failed to download ./repodata/cefcc9d56264aa169f70a53c560ffc39cb6af575-deltainfo.xml.gz

from http://download.opensuse.org/update/11.3/
A[code]...

View 8 Replies View Related

OpenSUSE :: Gnome3 - Check Whether Server Accessible

May 13, 2011

Cannot access installation media
Index of /repositories/GNOME:/STABLE:/3.0/openSUSE_11.4
GNOME:STABLE:3.0 (Medium 1).
Check whether the server is accessible.

Index of /repositories/GNOME:/STABLE:/3.0/openSUSE_11.4
File './x86_64/Mesa-7.10-1.2.x86_64.rpm' not found on medium '[URL]'
Fresh Install. Used Gnome3 link from here
openSUSE:GNOME 3.0 - openSUSE

Worked Yesterday. Not today

View 1 Replies View Related

OpenSUSE Network :: XP Pro Share Not Accessible In Explorer

Jun 10, 2010

I have a share accessible from XP. However if I go for lunch and come back when I click on the share in Explorer it says its not accessible. When I click on it again it works. Its like the network card in the Suse server is going to sleep but I cant see any settings for it. I know where they are in XP and wonder if they are somewhere in openSuse? Or if there is some other explanation.

View 6 Replies View Related

OpenSUSE Network :: Samba Share Only Accessible Via IP?

Oct 19, 2010

have a server here running opensuse 11.3 that I need to access via network using samba.
Samba is working so far and I can ping the serve and browse the shares from windows (WinXP) computers; but only via the IP.Now I've read up on samba on this forum and other sources, like the official samba documentation and compared my smb.conf with an older one on another server which works (and even copied this one over to the new one) - to no avail.I seem to be missing something and I just can't find it.Since the problem is probably not in the smb.conf (previously working one doesn't work on new server) - where else could I have screwed up?

View 6 Replies View Related

Debian :: Scanner No Longer Recognized After Update

Nov 30, 2015

I am running Wheezy 7.9 32 bit, with the kernel Linux 3.2.0-4-686-pae, and Gnome 3.4.2 on an Intel Pentium CPU G3420 @ 3.2 GHz. I installed a new printer in August, an HP Officejet 7612 all-in-one printer/scanner/copier, and it worked perfectly as both a printer and a scanner first time, despite not being listed on the supported list in SANE. Two weeks ago, I got a general software update notification, and did the update. Now the scanner is not recognised. The printer still works fine as a printer, but when using Simple-scan, I get the error message "No scanners detected. Please check your scanner is connected and powered on". I have had a look round on Google, and all the suggestions made do not work.

I tried the suggestion to add myself to the scanner users list on my PC which made no difference (even though the scanner previously worked without my being added to the scanner users list).

I have deleted the printer and re-installed it using CUPS, but that still has no effect. I tried re-installing HPLIP also to no avail, and I have now lost the toolbox on the drop down menu under <Applications> <Accessories> <HP Toolbox>, as when I click on it, nothing happens.

It would seem that something in the update has messed up Simple-scan. Looking at the dpkg log (is this the right thing to look at?) for the date of the update, I cannot find anything which directly involved SANE, so I think that it might be something else which has affected SANE. How I can find out which update did the damage? I don't normally do anything except accept recommended updates, so I am a bit lost as to what to do.

View 2 Replies View Related

Fedora :: 10 - Ran Update - Can No Longer Use Nivida Drivers ?

Aug 6, 2009

I ran an update yesterday ( like i do most days ) and now my dual screen doesnt work and when i load the nvidia conrol panel it says to run a command as root ( summat liek nivida-xorg ) it then does something tomy xorg that then completely breaks it.

I havent made any changes other than the update.

How do i get nvidia installed properly again?

Im currently running on a strange screen with 2 black lines on the sides and a bad res.

I fear its borked it royally?

View 4 Replies View Related

Ubuntu Installation :: No Longer Login After Update?

Feb 28, 2011

I am having a problem with the latest update of lucid ubuntu. I was on 10.04 for the longest time but decided to update while I was out doing errands. When I got back the logon screen was made up of blue and gray windows on a completely black background and the mouse and keyboard wouldn't work!

I found that if I unplugged and then replugged my mouse that I could get it working, but not all the options work properly. When you try to close a menu it just stays up, but it isn't there at the same time. Also, the shutdown/restart options don't work along with the physical power button on my computer, I have to remove the battery and power cord to shut it down.

I am currently dual booting ubuntu and windows 7 on my gateway NV59 laptop.

View 9 Replies View Related

Ubuntu :: Use The Update Manager It Says That It Is No Longer Supported?

May 31, 2011

I have a pc at work with 9.04 on it and when I try to use the update manager it says that it is no longer supported. how do i upgrade to the newest version?

View 6 Replies View Related

Ubuntu :: Cdrom And Hd No Longer Recognized After Update In 10.04?

Jun 5, 2011

After running an update in my 10.04 installation, both cdrom drives are not recognized anymore and won't even open when i push the eject button. Also, a 2TB storage drive is not recognized any longer and the computer won't even boot if that drive is plugged in..

View 5 Replies View Related

CentOS 5 :: KMail And PGP No Longer Working After 5.3 Update?

May 3, 2009

Have a problem to decrypt emails after I updated to 5.3. Didn't change anything to the pgp or Kpgp settings and Kmail says that it failed decryption with openpgp. As I don't know what to look for or what to check I am lost.. it encrypts outgoing messages just fine.

View 1 Replies View Related

OpenSUSE Hardware :: External NTFS USB Drive Not Accessible By Windows

Aug 11, 2010

I've been using it for a couple of years, it has been mounted various ways and into various places, for the past year under Suse 11.2

Suddenly I discover that it's not accessible in Windows anymore. Drive gets an assigned letter but can't be opened. Tried on Windows 7 and Windows Xp.

This is the current fstab line:

/dev/disk/by-id/usb-Seagate_FreeAgentDesktop_3QK0A0N7-0:0-part1/home/stan/Seagatentfs-3gdefaults,locale=en_US.UTF-800

Drive is owned by the root but permissions are set for everybody.

This is ls -l line for it's mount point

drwxrwxrwx 1 root root 8192 2010-07-16 21:48 Seagate

Another weird thing about it is that if I try to copy a folder into it Dolphin gives me "can't create directory" error and then hangs. If I restart Dolpin I see that the folder has been created just fine and I can copy anything into this new folder without any problems, including creating any sub-folders.

That weirdness doesn't exist if I run Dolphin as a superuser.

I would create a separate thread for this issue if there's no connection.

For now I believe something screwed up the part where Windows reads what file system it is.

Is there a way to "unscrew" it and make sure that NTFS looks ok to Windows, too?

Backing up 750 GB drive and reformatting it is not an option in the near future and I occasionally need to take the drive and plug it into friends' Windows.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved