OpenSUSE Install :: Invalid Module Format - FATAL: Error Inserting P4_clockmod

Jan 10, 2010

I have a problem with loading the powersaving kernel module p4-clockmod.ko. When I try inserting the module (via modprobe or insmod) I get FATAL: Error inserting p4_clockmod (/lib/modules/2.6.31.8-mediaserver/extra/p4-clockmod.ko): Invalid module format The module has been compiled together with the kernel. Other modules load with no problem at all. I've tried recompiling the kernel (after re-installing the sources, make xconfig from scratch) - no avail. There's only one kernel source package installed. Searching the forum and google didn't yield a helping answer.

View 9 Replies


ADVERTISEMENT

OpenSUSE :: VirtualBox: Error Inserting Vboxnetflt: Invalid Module Format

Jul 29, 2010

i installed SLES 11 sp1 as guest on openSUSE 11.3 host, then change the adapter network from 'NAT' to 'Bridged Adapter', but when i hit start i got this error message: Failed to open a session for the virtual machine sles. Failed to open/create the internal network 'HostInterfaceNetworking-wlan0' (VERR_SUPDRV_COMPONENT_NOT_FOUND). Failed to attach the network LUN (VERR_SUPDRV_COMPONENT_NOT_FOUND). One of the kernel modules was not successfully loaded. Make sure that no kernel modules from an older version of VirtualBox exist. Then try to recompile and reload the kernel modules by executing '/etc/init.d/vboxdrv setup' as root (VERR_SUPDRV_COMPONENT_NOT_FOUND). but when run: sudo /etc/init.d/vboxdrv setup

[Code]....

View 2 Replies View Related

OpenSUSE Wireless :: Linksys WUSB600N (rt2870) - Insmod: Error Inserting 'rt2870sta.ko': -1 Invalid Module Format

May 24, 2009

I'm new to openSUSE and as a matter of fact, to linux too. I've got a Linksys WUSB600N wireless adapter which used to work fine with some live versions of linux that I was testing out before moving onto suse... Each time, upon booting using live CDs, I used to copy the driver I had downloaded from:

SpeedShare - Download rt2870-kernel-2.6.24-nemesis.tar.bz2

Then 'make' and get into the driver's os/linux directory to load the driver using 'insmod rt2870sta.ko' Now, upon doing a 'make' and 'make install', followed by the 'insmod rt2870sta.ko', I get the error saying:

insmod: error inserting 'rt2870sta.ko': -1 Invalid module format

I tried doing 'modprobe -rv rt2870sta' and didn't get any error messages. But while doing 'modprobe -v', this error shows up: insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/rt2870sta.ko
FATAL: Error inserting rt2870sta (/lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/rt2870sta.ko): Invalid module format

View 7 Replies View Related

Slackware :: Nfsd In Current - WARNING: Error Inserting Sunrpc: Invalid Module Format

Mar 13, 2010

I'm having some troubles with nfsd in slackware-current. When I start the service, I get the following error messages: Quote:

WARNING: Error inserting sunrpc (/lib/modules/2.6.33-smp/kernel/net/sunrpc/sunrpc.ko): Invalid module format
WARNING: Error inserting auth_rpcgss (/lib/modules/2.6.33-smp/kernel/net/sunrpc/auth_gss/auth_rpcgss.ko): Invalid module format
WARNING: Error inserting lockd (/lib/modules/2.6.33-smp/kernel/fs/lockd/lockd.ko): Invalid module format
FATAL: Error inserting nfsd (/lib/modules/2.6.33-smp/kernel/fs/nfsd/nfsd.ko): Invalid module format

The mount fails from the clients with the error message: Quote: mount.nfs: access denied by server while mounting jupiter:/media/Backup A look at syslog from the server side gives: Quote: exportfs: exports duplicate symbol exportfs_decode_fh (owned by kernel) mountd[28198]: getfh failed: No such device kernel: exportfs: exports duplicate symbol exportfs_decode_fh (owned by kernel)

View 3 Replies View Related

Networking :: Rtl8187 Driver Module Load Error (Invalid Module Format)?

Jun 1, 2009

When I try to load the Realtek 8187 modules to kernel using the ./wlan1up command, I get the following error:

[root@localhost rtl8187_linux_26.1025.0328.2007]# ./wlan1up
insmod: error inserting 'ieee80211_crypt-rtl.ko': -1 File exists

[code]...

Can someone tell me how to correct the "Invalid module format"? I hope that correcting the "Invalid module format" error, I will not have the "Unknown symbol in module" error.

Note: I am using wlan1 for this module as I previously am online with the wlan0 network.The same error occurs if I use ./wlan0up.

View 3 Replies View Related

Fedora Networking :: Insmod Error - Invalid Module Format

Mar 4, 2011

I successfully built the sources for 64 bit linux drivers from [URL].... on the 64 bit F14 machine: Linux localhost.localdomain 2.6.35.6-45.fc14.x86_64 #1 SMP Mon Oct 18 23:57:44 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux and got wl.ko:

[Code]...

View 2 Replies View Related

OpenSUSE Hardware :: Modprobe Acpi-cpufreq -FATAL - Error Inserting - No Such Device

Apr 17, 2011

(Opensuse 11.4, nvidia, core2) PROBLEM: cpu goes into C3 powersaving state even on full load (even when disabled from bios) (acpi=off prevents this). opensuse 11.4 kernel ignores boot option processor.max_cstate=2 (option has no effect). cpufreq util should be able to change governor policy to performance, however acpi-cpufreq driver doesn't load: modprobe acpi-cpufreq -> FATAL: error inserting acpi_cpufreq (/lib.../acpi-cpufreq.ko): No such device

View 7 Replies View Related

OpenSUSE Install :: Booting With Bootsplash Turned Off / Sending Error FATAL: Module Ata_piix Not Found?

Dec 20, 2009

while booting with bootsplash turned off there's a message "FATAL: Module ata_piix not found FATAL: Error running install command for ata_piix" .Though everything works fine i'd like to know what does this message mean and is there a way to disable loading of ata_piix whatever it means.

View 2 Replies View Related

OpenSUSE Network :: CISCO Vpnclient - Invalid Module Format

Sep 7, 2010

I am trying to compile the Cisco vpnclient on my Opensuse 11.2 and (after some troubles) I got the module compiled and installed but when I try to load with insmod I got this error

<</etc/init.d/vpnclient_init start
Starting /opt/cisco-vpnclient/bin/vpnclient: insmod: error inserting '/lib/modules/2.6.31.12-0.2-default/CiscoVPN/cisco_ipsec.ko': -1 Invalid module format
Failed (insmod)>>

I am able to use the vpnclient forcing the module with modprobe -f cisco_ipsec but I'd prefer to solve the 'invalid format' original problem. I 'googled' around and it seems related with this warning during vpn_install script "WARNING: Symbol version dump /usr/src/linux-2.6.31.12-0.2/Module.symvers is missing; modules will have no dependencies and modversions." I have these rmps:........

View 2 Replies View Related

General :: Getting Error "invalid Module Format" And "insert Kernel Module" / What Is This?

Feb 22, 2010

What is the error "invalid module format" and the message "insert kernel module" mean? And whats the reason for the same?

View 8 Replies View Related

Slackware :: Modprobe Kvm-intel Gives An Error - FATAL: Error Inserting Kvm_intel

Jul 2, 2010

I've just install qemu-kvm from [URL]

I run modprobe kvm and modprobe kvm-intel to load the modules, but the second command won't work.

It gives the following error -

Code:

root@mika:/home/mika# modprobe kvm-intel

FATAL: Error inserting kvm_intel (/lib/modules/2.6.33.4/kernel/arch/x86/kvm/kvm-intel.ko): Operation not supported

View 10 Replies View Related

Fedora :: FATAL - Error Inserting Padlock_sha With 2.6.29.5-191 Kernel

Jun 25, 2009

I updated the latest kernel and other new maintenance tonight and started getting this error at boot...doesn't appear to be hindering anything. My encrypted partitions (luks, ext4) still open and are accessible.

modprobe: FATAL: Error inserting padlock_sha (/lib/modules/2.6.29.5-191.fc11.i586/kernel/drivers/crypto/padlock-sha.ko): No such device

See similar errors reported on ubuntu forums... with various recommended workarounds... update/add an alias, blacklist a module, fresh install

View 13 Replies View Related

Software :: Modprobe Usb-storage - FATAL - Error Inserting

Jun 5, 2010

I took some pictures tonight and plugged in my flash card reader (via usb) as always. Only this time, the device isn't assigned a proper location (like "sdc3").

A little research later and I *think* I need the module "usb-storage", which I can't get to load. It's been a *long* time since I had to mess with modules and I'd like some fresh eyes on what the problem might be.

This is my lsmod output:

Code:

I also ran modprobe with -n -v:

Code:

I have run depmod -a and tried the modprobe again...

Code:

If I drill down to the /lib/modules/<kernel -r>/drivers/usb/storage/ where the .ko file is and say:

Code:

So.... since I haven't changed anything that I can think of since the last time I took pictures...what happened? How do I fix this?

View 3 Replies View Related

General :: FATAL: Error Inserting Ip_tables When Try To Create New Iptable

Jun 16, 2010

So I am new to ubuntu and am trying to work with "iptables". I have ubuntu version 10.04, in the terminal I try to create a new iptable by writing: iptables -N chain but the response is: FATAL: Error inserting ip_tables......... also it says "you must be root", what does root mean?

View 2 Replies View Related

Ubuntu :: Access The Tty's - When Hit Ctrl + Alt + F1 Get A Screen That Says - FATAL: Error Inserting Uvesafb

Jul 20, 2010

I am running ubuntu 10.04 I am trying to access the tty's

When I hit Ctrl + Alt + F1 I get a screen that says: FATAL: Error inserting uvesafb (/lib/modules/2.6.32-23-generic/kernel/drivers/video/uvesafb.ko): unknown symbol in module, or unknown parameter (see dmesg)

Ctrl + Alt + F2-F6 all I get is a flashing cursor that won't do anything

View 1 Replies View Related

Red Hat :: Error Inserting MD5 - Invalid Argument

Mar 24, 2011

I am running Red Hat with 2.6.18-194.8.1.el5PAE kernel version. I am trying to run encryptfs to encrypt a partition on my hard drive. One of the kernel modules necessary is the md5.ko. I noticed it wasn't loaded in when doing an lsmod. I tried running modprobe md5 and it fails to load:

[root@ ~]# /sbin/modprobe -v md5
insmod /lib/modules/2.6.18-194.8.1.el5PAE/kernel/crypto/md5.ko
FATAL: Error inserting md5 (/lib/modules/2.6.18-194.8.1.el5PAE/kernel/crypto/md5.ko): Invalid argument

I ran dmesg and grepped for md5, but I didn't see anything in there.

View 1 Replies View Related

OpenSUSE Install :: Fatal - MBcache And Ahci Module Not Found

Nov 30, 2009

I am using openSuSE 11.2 on a VGN-AR41L. I have also erased the preinstalled Home Vista (what a pleasure). Now to my problem. My system boots correctly but if I press the <ESC> key while booting I can see the following messages:

"Doing fast boot
FATAL: mbcache module not found
FATAL: ahci module not found
"
and the boot process continues normally.

Why this happens? Does this mean that I have a problem that I haven't discovered yet? Is it something that I can ignore? I am using SUSE Linux from version SUSE Linux 8 personal and although I am not a power user I have done my two desertions on this system and I am very happy with SUSE. I have bought SUSE Linux 8 Personal and SUSE Linux 10 all the other versions until today have been downloaded.

View 6 Replies View Related

OpenSUSE Install :: VMtoolsd Fatal - Module Vmmemctl Not Found?

Feb 8, 2011

vmtoolsd FATAL: Module vmmemctl not found.
What does this mean and should I activate/deactivate anything in the system or is this no problem.

View 8 Replies View Related

Software :: Insmod Failed With Invalid Module Format 1

Jun 22, 2011

With hello kernel module, i use two types of Makefile, one is using kernel build system:

obj-m += hello.o
all:
make -C /lib/modules/$(shell uname -r)/build M=$(PWD) modules

module loads successfully; another is using (CC) and then creating the module by "make -C /lib/modules/$(shell uname -r)/build M=$(PWD) modules", this module gives the error message when it is inserted, .........

View 5 Replies View Related

OpenSUSE Install :: Root Fs Mounts R/o After Update To 11.2 - FATAL: Module Jbd Not Found

Dec 13, 2009

I've updated my openSUSE 11.1 to 11.2 using installation DVD. After that, as system boots, I started to get lines like:

Code: FATAL: Module jbd not found
FATAL: Module mbcache not found
FATAL: Module ext3 not found and so on with different modules.. and this exact string several times:

Code: WARNING: All config file need .conf: /etc/modprobe.d/tv, it will be ignored in a future release. Finally I get:

[Code]....

View 4 Replies View Related

Debian Hardware :: Advantech USB 4761: Invalid Module Format

Jan 20, 2010

I've got a brand new Advantech USB 4761 Digital/Analog PC Lab card. They claim to run under Linux. The install, " dpkg -i advdaq_1.04.0006-1_i386.deb", was successful. But when I tried to modify and run their install script, "adv_load_template", I get this:./adv_load_templateinsmod: error inserting './modules/advdrv_core.ko': -1 Invalid module format insmod: error inserting './modules/usb4761.ko': -1 Invalid module format

View 1 Replies View Related

General :: ZTE AC2726 Not Working In Fedora 11 - Invalid Module Format

Apr 18, 2010

I am using reliance zte modem ac2726.i inserted the modem in my laptop and tried wvdialconf command and it was working.but when i type

Code:

modprobe usbserial vendor=0x19d2 product=0xfffd

command it shows the following error message

Code:

FATAL: Error inserting usbserial (/lib/modules/2.6.29.4-167.fc11.i686.PAE/kernel/drivers/usb/serial/usbserial.ko): Invalid module format
But "cat /proc/bus/usb/devices","lsusb","dmesg" everything are working perfectly."Wvdial.conf" file also got configured perfectly.what can i do now?

View 3 Replies View Related

Slackware :: Invalid Module Format Both Broadcom Wireless And Nvidia Gfx

Jan 25, 2011

A little background first: Wireless card: Broadcom BCM4312 Wireless driver used: [URL].... (and slackbuild variation of the same)
GFX card: nVidia geForce 7150m I installed Slackware yesterday, along side my Ubuntu (yes yes, I use Ubuntu lol. I've been using it for about four years, I added Slackware to grub.cfg, using the OS prober, which added four menu entries. The first two caused kernel panic, the third worked, and I don't think I tried the fourth. (I'm pretty sure they were, in this order: generic, generic-smp, huge, and huge-smp). Using huge, I could not modprobe my wireless driver, I would get a "Invalid Module Format" error with wl, and when installing the nVidia drivers (from their site), I would get:

[code]....

I then booted using a menuentry my friend gave me, created my initrd, and everything worked fine, both graphics and wireless (mostly fine). So I upgraded to -current, kernel 2.6.35.10, and I started getting the same errors as before, 'Invalid Module format' and the same thing with the nVidia drivers, although this time, it happens regardless of if I use the generic kernel, or the huge kernel. I've done heaps of Google'ing around, and nothing I found worked.

View 8 Replies View Related

General :: Error Inserting Module ?

Jan 31, 2011

I am having a problem while inserting a particular module.

Following are some prints :-

I am using STLinux-2.4 Distribution, kernel 2.6

I have changed the access permissions on all the .ko as rwx. Still I am getting the problem.

View 2 Replies View Related

Programming :: Insmod: Error Inserting 'kernel.ko': -1 Invalid Parameters?

Jan 16, 2010

insmod: error inserting 'kernel.ko': -1 Invalid parametersI am getting this error when i am try to insert kernel.ko into kernelMy systemfedora 12 with gcc 4.4.2insmod kernel.koinsmod: error inserting 'kernel.ko': -1 Invalid parametersmy program

__________________kernel.c________________________ ___________

#include <linux/module.h> /* Needed by all modules */
#include <linux/kernel.h> /* Needed for KERN_INFO */

[code].....

View 4 Replies View Related

Hardware :: Error During Inserting Of Parallel Port Module

Apr 15, 2011

I am tiring to insert a parallel port module into the kernel when i received this error.

[root@localhost paralelport]# ls
a.out light.c Module.markers parlelport.c parlelport.mod.c parlelport.o
light Makefile Module.symvers parlelport.ko parlelport.mod.o
[root@localhost paralelport]# make
make -C /lib/modules/2.6.18-128.el5/build M=/home/backup/parallal/paralelport modules
make[1]: Entering directory `/usr/src/kernels/2.6.18-128.el5-i686'

[Code]...

View 1 Replies View Related

OpenSUSE Install :: Cant Boot Xp - Invalid Or Unsupported Executable Format Chainloader +1

Sep 27, 2010

I was installing opensuse on the c partition and it gave errors so i aborted it now i click on windows and it says invalid or unsupported executable format chainloader +1 so then i proceeded to try and fix this by changing the menu.lst to this:

And now it tells me that disk isnt found so i need to know what to put in the menu.lst to load the actual windows partition and then fix the original error.

View 9 Replies View Related

Debian Configuration :: FATAL: Error Inserting Pcc_cpufreq (/lib/modules/3.0.0-1-amd64/kernel/drivers/cpufreq/pcc-cpufreq.ko): No Such Device

Jul 31, 2011

I recently started having this odd behaviour while using and loading cpufrequtils on boot, I don't know if it is happening to someone else.During boot I'm getting( when /etc/init.d/cpufrequtils invokes /etc/init.d/loadcpufreq to load the proper module):

Loading cpufreq kernel modules...FATAL: Error inserting speedstep_centrino (/lib/modules/3.0.0-1-amd64/kernel/drivers/cpufreq/speedstep-centrino.ko): No such device
FATAL: Error inserting pcc_cpufreq (/lib/modules/3.0.0-1-amd64/kernel/drivers/cpufreq/pcc-cpufreq.ko): No such device

[code]....

View 2 Replies View Related

Debian Configuration :: FATAL: Error Inserting Nvidia (/lib/modules/2.6.26-2-686/nvidia/nvidia.ko): No Such Device

Mar 15, 2010

I'm trying to install the nvidia drivers but it is not working.

lspci | grep VGA

02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX - nForce GPU] (rev a3)

My xorg.conf looks like this:

# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.

[code]...

And after that my X is not working. And when i try sudo modprobe nvidia I get this:

FATAL: Error inserting nvidia (/lib/modules/2.6.26-2-686/nvidia/nvidia.ko): No such device

View 2 Replies View Related

Ubuntu Installation :: Grub And 9.04 - Error "invalid Command" Or "invalid Execution Format"

Aug 16, 2011

Bottom Line: Dvd Drive died in my toshiba laptop and it was replaced (not before tech for some reason reformatted the Win7 partition... which was 100% un-needed, but thats beside the point now. I redid win7 (the tech installed vista) and am TRYING to "redo grub". Facts: The Slackware AND Ubuntu Partitions ARE STILL THERE and when i use SuperGrub Boot CD (which doesn't restore my grub by itself) to boot into slackware, i can see ALL THE CONTENT of both Linuxes still there including grub on ubuntu partition

(Tri-Boot: Ubuntu, Slackware, and WIn7) I had it working for two years or so, SO i know this "setup" works fine. I am A) Trying to do this as simply as possible. B) Trying to avoid the need to download a 800MB ISO (as seen for this issue on this forum) and trying not to have to reformat Ubuntu Partition (though I have the .Debs I have downloaded for it backed up ... all 1.7GB of them) I have /dev/sda1 as win7, /dev/sda2 as Slack and /dev/sda3 as Ubuntu (which contains Grub Legacy).. Every command I do seems to result in an error like "invalid command" or "invalid Execution format " (i think that second one is right) type errors. I compiled (awhile back) a few kernels for Slackware, but feel goofy that I cant figure what i this out (what i thought was going to be a "2 minute" fix)

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved